Beko wmy 7046LB2 User Manual
Washing Machine
User’s Manual
WMY 7046 LB2
Document Number
2820524400/ 25-11-14.(10:37)
This product was manufactured using the latest technology in environmentally friendly conditions.
1 General safety instructions
This section includes security instructions which may help prevent the
injuries and material damage risks. All kinds of warranties shall be invalid if
these instructions are not observed.
1.1 Life and property safety
u
Never place the product on a carpet-covered floor. Electrical parts will get
overheated since air cannot circulate from under the device. This will cause
problems with your product.
u
Unplug the product if it is not in use.
u
Always have the installation and repairing procedures carried out by the
Authorized Service Agent. Manufacturer shall not be held liable for damages
that may arise from procedures carried out by unauthorized persons.
u
The water supply and draining hoses must be securely fastened and remain
undamaged. Otherwise, water leak may occur.
u
While there is still water inside the product, never open the loading door or
remove the filter. Otherwise, risk of flooding and injury from hot water will
occur.
u
Do not force open the locked loading door. Door can be opened a few
minutes after the washing cycle ends. In case of forcing the loading door to
open, the door and the lock mechanism may get damaged.
u
Use detergents, softeners and supplements suitable for automatic washing
machines only.
u
Follow the instructions on the label of textiles and the detergent package.
1.2 Children's safety
u
This product can be used by the children who are at the age of 8 and
over and the people whose physical, sensory or mental skills are not
fully developed or who do not have necessary required experience and
knowledge as long as they are supervised or trained about the safe use of
the product and its risks. Children should not play with the device. Cleaning
and maintenance works should not be performed by children unless they
are supervised by someone. Children of less than 3 years should be kept
away unless continuously supervised.
u
Packaging materials may be dangerous for the children. Keep packaging
materials in a safe place away from reach of the children.
u
Electrical products are dangerous for the children. Keep the children away
from the product when it is in use. Do not allow them to play with the product.
Use child lock to prevent children from intervening with the product.
3 / EN
Washing Machine / User’s Manual
u
Do not forget to close the loading door when leaving the room where the
product is located.
u
store all detergents and additives in a safe place away from the reach of
the children by closing the cover of the detergent container or sealing the
detergent package.
1.3 Electrical safety
u
If the product has a failure, it should not be operated unless it is repaired by
the Authorized Service Agent. Risk of electric shock!
u
This product is designed to resume operating in the event of powering
on after a power interruption. If you wish to cancel the programme, see
"Cancelling the programme" section.
u
Plug the product into a grounded outlet protected by a 16 A fuse. Do not
neglect to have the grounding installation made by a qualified electrician.
Our company shall not be liable for any damages that will arise when the
product is used without grounding in accordance with the local regulations.
u
Do not wash the product by spraying or pouring water onto it! Risk of electric
shock!
u
Never touch the power cable plug with wet hands! Do not grab the power
cord to unplug the machine, always unplug it by holding the socket with one
hand, and pulling the plug with the other hand.
u
Product should be unplugged during installation, maintenance, cleaning
and repair procedures.
u
If the power cable is damaged, it must be replaced by the manufacturer,
after sales service or a similarly qualified person (preferably an electrician)
or someone designated by the importer in order to avoid possible risks.
1.4 Hot surface safety
4 / EN
While washing the laundry at high temperatures,
the loading door glass will get hot. Considering
this fact, during washing operation keep the
children away from the loading door of the
product to prevent them touching it.
Washing Machine / User’s Manual
2 Important instructions for environment
2.1 Compliance with WEEE Directive
This product complies with EU WEEE Directive (2012/19/EU). This product bears a
classification symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which can be
reused and are suitable for recycling. Do not dispose of the waste product with normal
domestic and other wastes at the end of its service life. Take it to the collection center for
the recycling of electrical and electronic equipment. Please consult your local authorities to
learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain
harmful and prohibited materials specified in the Directive.
2.2 Package information
Packaging materials of the product are manufactured from recyclable materials in accordance with
our National Environment Regulations. Do not dispose of the packaging materials together with the
domestic or other wastes. Take them to the packaging material collection points designated by the local
authorities.
3 Intended use
• This product has been designed for domestic use. It is not for commercial purposes or it
should not be used out of its intended use.
• The product must only be used for washing and rinsing of laundry that are marked
accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage or
transportation.
5 / EN
Washing Machine / User’s Manual
4 Technical specifications
Supplier name or trademark Beko
Model name
Rated capacity (kg) 7
Energy efficiency class / Scale from A (Highest Efficiency) to D (Lowest Efficiency) A+++
Maximum spin speed (rpm) 1400
Height (cm) 84
Width (cm) 60
Depth (cm)
Net weight (±4 kg.) 71
Single Water inlet / Double Water inlet
• Available
Electrical input (V/Hz) 220-240 V / 50Hz
Total current (A) 10
Total power (W) 2000-2350
Main model code
Technical specifications may be changed without prior notice to improve the quality of the product.
WMY 7046 LB2
54
• / -
1011
6 / EN
Washing Machine / User’s Manual
4.1 Installation
• Apply to the nearest authorized service agent for the installation of your product.
• Preparation of the location and electrical, tap water and waste water installations at the place of installation
is under customer's responsibility.
• Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or
crushed while pushing the product into its place after installation or cleaning procedures.
• Make sure that the installation and electrical connections of the product are performed by authorized
service. Manufacturer shall not be held liable for damages that may arise from procedures carried out by
unauthorized persons.
• Prior to installation, visually check if the product has any defects on it. If so, do not have it installed.
Damaged products cause risks for your safety.
4.1.1 Appropriate installation location
• Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other similar
surfaces.
• When the washing machine and drier are placed on top of each other, their total weight –when loaded–
amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying
capacity!
• Do not place the product on the power cable.
• Do not install the product in the environments where the temperature falls below 0 ºC.
• Leave a minimum space of 1 cm between the machine and the furniture.
• On a graduated floor, do not place the product next to the edge or on a platform.
4.1.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging reinforcement.
Remove the packaging reinforcement by pulling the ribbon. Do not make
this operation alone by yourself.
4.1.3 Removing the transportation locks
1 Loose all bolts with an appropriate wrench until they turn freely (C).
2 Remove the transport safety bolts by turning them slightly.
3 Insert the plastic covers in the bag containing the user manual to the openings on the rear panel. (P)
CAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be
A
C
7 / EN
damaged.
Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the
future.
Install the transport safety bolts in reverse order of the disassembly procedure.
Never move the product without the transportation safety bolts properly fixed in place!
Washing Machine / User’s Manual
4.1.4 Connecting water supply
The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have
10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure
C
A
reducing valve if water pressure is higher.
If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the supplied stopper
to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.)
CAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will
get damaged or the product will switch to protection mode and will not operate.
CAUTION: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.
Connect the special water supply hoses supplied with the product to the water inlets on the
product. Red hose (left) (max. 90 ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is
for cold water inlet.
Make sure that the hot and cold water taps are connected correctly when the product is
being installed. Otherwise, your laundry will come out hot at the end of the washing process
and wear out.
1 Tighten the nuts of the hose by hand. Never use a tool when
tightening the nuts.
2 When hose connection is completed, check whether there is leak
problems at the connection points by opening the taps fully. If any
leaks occur, turn off the tap and remove the nut. Retighten the nut
carefully after checking the seal. In order to prevent the water leaks
and resultant damages, keep the taps closed when you do not use
the product.
4.1.5 Connecting the drain hose to the drain
• Attach the end of the drain hose directly to waste water drain, lavatory or bathtub.
CAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge. Moreover, there
A
is risk of scalding due to high washing temperatures! In order to prevent such situations and make sure that the machine
performs water intake and discharge processes without any problem, fix the drain hose securely.
• Connect the drain hose to a minimum height of 40 cm
and a maximum height of 100 cm.
• In case the drain hose is elevated after laying it on the
floor level or close to the ground (less than 40 cm above
100cm
• To prevent the waste water to go back into the machine again and to ensure easy drainage, do not immerse
the end of the hose into the waste water or do not insert it into the drain for more than 15 cm. If it is too
long, cut it short.
• The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched
between the drain and the machine.
• If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may
not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the
drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.
8 / EN
the ground), water discharge becomes more difficult and
the laundry may come out excessively wet. Therefore,
40cm
follow the heights described in the figure.
Washing Machine / User’s Manual
4.1.6 Adjusting the feet
CAUTION: In order to ensure that the product operates more silently and vibration-free, it must stand level and balanced
A
1 Loosen the lock nuts on the feet by hand.
2 Adjust the feet until the product stands in a stable and balanced way.
3. Tighten all lock nuts by hand again.
4.1.7 Electrical connection
Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for any
damages that will arise when the product is used without grounding in accordance with the local regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after installation.
• If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician
install a 16 Amp fuse.
• The voltage specified in the "Technical specifications" section must be equal to your mains voltage.
• Do not make connections via extension cables or multi-plugs.
on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing
and vibration problems.
CAUTION: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.
B
4.1.8 Initial use
C
9 / EN
CAUTION: Damaged power cables must be replaced by the Authorized Service Agents.
Before starting to use the product make sure that the preparations are
made which are in line with the “Important Safety and Environment
Instructions” and the instructions in the “Installation” section.
To prepare the product for washing laundry, perform first operation
in Drum Cleaning programme. If this program is not available in your
machine, apply the method which is described in the section 4.4.2.
Use an anti-limescale suitable for the washing machines.
Some water might have remained in the product due to the quality control processes in the production. It is not harmful for
the product.
Washing Machine / User’s Manual
Loading...