User manual
A50-71533-00001
EUROLIVE E1220A/E1520A
EUROLIVE E1220A/E1520A
2
Important safety instructions
This symbol, wherever it appears, alerts you to the
presence of uninsulated dangerous voltage inside the
*
enclosure - voltage that may be sufcient to constitute
a risk of shock.
This symbol, wherever it appears, alerts you to important
operating and maintenance instructions in the accom-
!
panying literature. Please read the manual.
Warning
To reduce the risk of electric shock, do not remove the +
top cover (or the rear section). No user serviceable parts
inside; refer servicing to qualied personnel.
To reduce the risk of re or electric shock, do not expose +
this appliance to rain and moisture. The apparatus shall
not be exposed to dripping or splashing and no objects
lled with liquids, such as vases, shall be placed on
the apparatus.
These service instructions are for use by qualied +
service personnel only. To reduce the risk of electric
shock do not perform any servicing other than that
contained in the operation instructions unless you are
qualied to do so.
Ventilation:
The appliance should be situated so that its location or +
position does not interfere with its proper ventilaton.
For example, the appliance should not be situated on
a bed, sofa, rug, or similar surface that may block the
ventilation openings, or placed in a built-in installation,
such as a bookcase or cabinet that may impede the ow
of air through the ventilation openings.
Check the oor:
Always check the oor for stability before you set up the +
speaker cabinet. Vibrating oors (e.g. elements/compo-
nents on the stage) do not provide reliable support for
speaker stacks. So, always set up your speakers on a
solid and even support.
Read these instructions.1)
Keep these instructions.2)
Heed all warnings.3)
Follow all instructions.4)
Do not use this apparatus near water.5)
Clean only with dry cloth.6)
Do not block any ventilation openings. Install in accor-7)
dance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, 8)
heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
Do not defeat the safety purpose of the polarized or 9)
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not t into your outlet, consult an electrician
for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched 10)
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
The apparatus shall be connected to a MAINS socket 11)
outlet with a protective earthing connection.
Where the MAINS plug or an appliance coupler is used 12)
as the disconnect device, the disconnect device shall
remain readily operable.
Use only attachments/accessories specified by the 13)
manufacturer.
Use only with the cart, stand, tripod, 14)
bracket, or table specied by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when 15)
unused for long periods of time.
Refer all servicing to qualied service personnel. Servic-16)
ing is required when the apparatus has been damaged in
any way, such as power supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or mois-
ture, does not operate normally, or has been dropped.
Make sure that speaker cabinets are set up properly:
Set up your speaker cabinet at a distance to dance oors +
or other audience areas, so as to avoid the possibility
of somebody knocking over a speaker stack.
EUROLIVE E1220A/E1520A
3
E1220A/E1520A
EUROLIVE
Processor-Controlled 400-Watt 2-Way PA Loudspeaker/Floor Monitor
High-power 400-Watt 2-way PA sound reinforcement speaker/oor monitor for live =
and playback applications
Exceptional sound quality, wide frequency bandwidth and extensive dynamic range =
Integrated sound processor for ultimate system control and speaker protection =
Extremely powerful 12"/15" long-excursion driver provides incredibly deep bass and acoustic power =
Proprietary 1'' HF driver for exceptional high-frequency reproduction =
Ultra-low noise Mic/Line input with Volume control and Clip LED =
Additional Line output allows linking of additional speaker systems =
Versatile enclosure prole allows different positioning: =
10 & 35 degree cluster and stacking mode -
Stand mounting with 35-mm pole socket -
Floor monitor wedge -
Ergonomically shaped handles for easy carrying and setup =
Rugged steel grill for optimal speaker protection =
High-quality components and exceptionally rugged construction ensure long life =
Conceived and designed by BEHRINGER Germany =
EUROLIVE E1220A/E1520A
Introduction4
Foreword
Dear customer,
welcome to the community
of EUROLIVE users, and
thank you very much for
expressing your confidence in us by purchasing
these PA loudspeakers.
Writing this foreword for
you gives me great pleasure, because it represents the culmination of
many months of hard work
delivered by our engineering team to achieve a very
ambitious goal: to develop
an outstanding PA system
that offers a maximum in
exibility and performance
th rough its imp ressive
sound character and out-
standing fea tures. The
task of designing our new E1220A/E1520A certainly meant a great
deal of responsibility, which we assumed by focusing on you, the
discerning user and musician. Meeting your expectations also
meant a lot of work and night shifts. But it was fun, too. Developing a product usually brings a lot of people together, and what a
great feeling it is when all who participated in such a project can
be proud of what they’ve achieved.
It is our philosophy to share our enjoyment with you, because you
are the most important member of the BEHRINGER team. With
your highly competent suggestions for new products you’ve made
a signicant contribution to shaping our company and making it
successful. In return, we guarantee you uncompromising quality
as well as excellent technical and audio properties at an extremely
reasonable price. All of this will enable you to give free rein to your
creativity without being hampered by budget constraints.
We are often asked how we manage to produce such high-quality
devices at such unbelievably low prices. The answer is quite
simple: it’s you, our customers! Many satised customers mean
large sales volumes enabling us to get better purchasing terms
for components, etc. Isn’t it only fair to pass this benet on to you?
Because we know that your success is our success too!
I would like to thank all of you who have made the E1220A/E1520A
possible. You have all made your own personal contributions, from
the developers to the many other employees at this company, and
to you, the BEHRINGER user.
Table of Contents
1. Introduction ......................................................................... 4
1.1 Before you get started .................................................. 4
1.1.1 Shipment ............................................................. 4
1.1.2 Initial operation ................................................... 5
1.1.3 Online registration ............................................... 5
2. Control elements and connections ................................... 5
3. Application examples ......................................................... 6
3.1 Using a mixing console ................................................ 6
3.2 Using several E1220A/E1520A loudspeakers.............. 6
3.3 Direct connection of a stereo signal source ................. 6
4. Installation........................................................................... 7
5. Specications ..................................................................... 7
6. Warranty .............................................................................. 8
Introduction1.
Thank you for the condence you have placed in us by purchasing
the BEHRINGER EUROLIVE E1220A/E1520A speaker. Targeting
DJs and presenters, these extremely robust, high-power loudspeakers offer amazing performance, durability and portability
that have made the series of EUROLIVE loudspeakers so widely
used and appreciated.
With powerful 400 Watts, wide frequency bandwidth and extensive
dynamic range, these sound reinforcement speakers deliver truly
impressive sound. The powerful long-excursion drivers crank out
big tone in the bottom end and mid-range, while the state-of-theart 1" HF drivers deliver crisp and detailed highs. Each speaker
has been optimized for maximum reliability through the integrated
sound processor, ensuring ultimate system control and speaker
protection. The enclosure's shape not only allows use in an up-
right position, but can also be tilted for use as a oor monitor. It
also offers a high degree of durability that can endure even the
harshest road conditions.
My friends, it’s been worth the effort!
Thank you very much,
Uli Behringer
Before you get started1.1
Shipment1.1.1
Your E1220A/E1520A was carefully packed at the assembly plant
to assure secure transport. Should the condition of the cardboard
box suggest that damage may have taken place, please inspect the
unit immediately and look for physical indications of damage.
Damaged equipment should NEVER be sent directly to +
us. Please inform the dealer from whom you acquired the
unit immediately as well as the transportation company
from which you took delivery. Otherwise, all claims for
replacement/repair may be rendered invalid.
Please always use the original packaging to avoid dam- +
age due to storage or shipping.
Ne ve r let unsuperv is ed chi ld re n pl ay with the +
E1220A/E1520A or with its packaging.
Please dispose of all packaging materials in an environ- +
mentally friendly fashion.
EUROLIVE E1220A/E1520A
Control elements and connections 5
Initial operation1.1.2
Be sure that there is enough space around the unit for cooling.
To avoid overheating, do not place the E1220A/E1520A on top of
power amps or near radiators, etc.
Blown fuses must be replaced by fuses of the same +
type and rating. Please refer to the “SPECIFICATIONS”
for further details.
The mains connection is made using the enclosed power cord
and a standard IEC receptacle. It meets all international safety
certication requirements.
Please make sure that all equipment is properly ground- +
ed at all times. For your own safety, never remove or
disable the ground conductor of the unit or of the AC
power cord.
The sound quality may diminish within the range of pow- +
erful broadcasting stations and high-frequency sources.
Increase the distance between the transmitter and the
device and use shielded cables for all connections.
Warning
This loudspeaker is capable of producing extreme vol- +
umes. Please keep in mind that high sound pressures do
not only temporarily damage your sense of hearing, but
can also cause permanent hearing damage. Be careful
to select a suitable volume at all times.
Online registration1.1.3
Please remember to register your new BEHRINGER equipment
right after your purchase by visiting www.behringer.com (alternatively www.behringer.de) and read the terms and conditions of
our warranty carefully.
Should your BEHRINGER product malfunction, our goal is to
have it repaired as quickly as possible. To arrange for warranty
service, please contact the retailer from whom the equipment was
purchased. Should your BEHRINGER dealer not be located in your
vicinity, contact directly one of our subsidiaries. Corresponding
contact information is included in the original equipment packaging (Global Contact Information/European Contact Information).
Should your country not be listed, please contact the distributor
nearest you. A list of distributors can be found in the support area
of our website (www.behringer.com).
Registering your purchase and equipment with us helps us process
your repair claims quicker and more efciently.
Thank you for your cooperation!
Control elements and connections2.
Control elements and connections (E1220A and Fig. 2.1:
E1520A)
Use this 1/4" stereo jack to connect a signal source that {1}
has 1/4" output.
Use this XLR connector to connect a signal source that has {2}
XLR output.
Always use either the XLR or the 1/4" jack input, and +
use the LEVEL control {4} to adapt the input sensitivity.
Never use both inputs at the same time!
The {3} LINK OUTPUT is directly connected to the inputs of
the E1220A/E1520A and carries the input signal with no
processing applied. In this way, you can route the signal
to the input of another device (for example, a second
E1220A/E1520A).
To set the volume of the LINE or MIC signal, use the {4} LEVEL
control. The left half of the control range is for attenuating
the LINE signal. The right half is for raising the level of the
MIC signal.
The {5} CLIP LED lights up when signal distortion occurs.
Reduce the volume with the LEVEL control until the CLIP
LED does not light up any more, or occasionally lights up
at signal peaks.
We would like to draw your attention to the fact that ex- +
tremely loud sound levels may damage your hearing as
well as your headphones/loudspeakers. Turn the LEVEL
control fully to the left before you switch on the unit. Be
careful to select a suitable volume at all times.
The {6} HIGH control adjusts the level of the high-frequency
range.
The {7} PWR LED lights up when the loudspeaker is put into
operation.
The {8} LOW control adjusts the level of the low-frequency
range.
EUROLIVE E1220A/E1520A
Application examples6
EUROLIVE E1520A
INPUTINPUT
INPUT
Output LOutput R
INPUT
LINK OUTPUT LINK OUTPUT
EURORACK UB2442FX-PRO
Application examples3.
Turn the LEVEL control fully to the left before you switch +
on the unit with the POWER switch. Then, raise the
volume to a suitable level.
Using a mixing console3.1
A common way to use 2 E1220A/E1520A loudspeakers is with
a mixing console. In this case, connect each of the main outputs
that are on the mixing console to a E1220A/E1520A loudspeaker.
The E1220A/E1520A includes XLR and 1/4" connectors. To avoid
interference, use only XLR or 1/4" jack cables.
Using several E1220A/E1520A loudspeakers3.2
Control elements and connections Fig. 2.2:
(E1220A and E1520A)
The mains connection is established using a cable with {9}
an IEC mains connector. This cable is packaged with the
E1220A/E1520A. To avoid ground-loop hum, loudspeakers and mixing consoles should be connected to the same
power circuit.
You can replace fuses at the [10] FUSE SWITCH of the
E1220A/E1520A. Always replace fuses with the same type.
Please follow the instructions given in chapter 5 “SPECIFICATIONS.”
Press [11] POWER to turn on your E1220A/E1520A.
The POWER switch does not fully disconnect the unit +
from the mains. To disconnect the unit from the mains,
pull out the main cable plug or appliance coupler. When
installing the product, ensure the plug or appliance
coupler is readily operable. Unplug the power cord
completely when the unit is not used for prolonged
periods of time.
SERIAL NUMBER[12]
Wiring several E1220A/E1520A loudspeakers using Fig. 3.1:
the LINK OUTPUT connector
For larger rooms, you can connect several E1220A/E1520A speakers using the LINK OUTPUT connector {3} (see g. 3.1).
Direct connection of a stereo signal source3.3
When you use two E1220A/E1520A loudspeakers, you can directly
connect one stereo signal source, for example, a CD player. In
this case, each of the speakers is connected to 1 signal-source
output. (If necessary, use the appropriate adaptor.)
EUROLIVE E1220A/E1520A
Specications 7
Installation4.
Both audio inputs of the BEHRINGER E1220A/E1520A and the
LINK OUTPUT connector are fully balanced. To maximize interference compensation, try to establish balanced connections to other
equipment, whenever possible.
1/4" TRS connectorFig. 4.1:
XLR connectorFig. 4.2:
Make sure that only competent personnel install your +
E1220A/E1520A. They must be sufciently earthed during and after the installation process. Otherwise, elec-
trostatic discharges may negatively affect the operating
characteristics of your equipment.
Specications5.
Output power
Low-frequency range
RMS @ 1% THD 200 W @ 8 Ω
Peak power 320 W @ 8 Ω
High-frequency range
RMS @ 1% THD 50 W @ 8 Ω
Peak power 80 W @ 8 Ω
Input
XLR connector (servo-balanced)
Sensitivity -40 to +4 dBu
Input impedance 24 kΩ
1/4" jack (servo-balanced)
Sensitivity -40 to +4 dBu
Input impedance 24 kΩ
Link output
XLR connector
System data
E1220A
Frequency range 60 Hz to 20 kHz
Crossover frequency 2.2 kHz (12 dB)
Maximum sound pressure level 124 dB @ 1 m
Limiter optical
Dynamic Equalizer Processor-controlled
E1520A
Frequency range 50 Hz to 20 kHz
Crossover frequency 2 kHz (12 dB)
Maximum sound pressure level 125 dB @ 1 m
Limiter optical
Dynamic Equalizer Processor-controlled
Equalizer
HIGH 12 kHz / ± 15 dB
LOW 80 Hz / ± 15 dB
Power supply
Mains voltage/fuses
100 -120 V~, 50/60 Hz T 5,0 A H 250 V
220 -230 V~, 50/60 Hz T 2,5 A H 250 V
Power consumption max. 400 W
Mains connector Standard IEC receptacle
Dimensions/Weight
E1220A
Dimensions (H x W x D) approx. 400 x 410 x 585 mm
Weight approx. 22.3 kg
E1520A
Dimensions (H x W x D) approx. 465 x 485 x 640 mm
Weight approx. 26.3 kg
BEHRINGER is constantly striving to maintain the highest professional standards.
As a result of these efforts, modications may be made from time to time to existing
products without prior notice. Specications and appearance may differ from those
listed or illustrated.
approx. 15.7" x 16.1" x 23"
approx. 49 lbs.
approx. 18.3" x 19" x 25.2"
approx. 58 lbs.
EUROLIVE E1220A/E1520A
Warranty8
Warranty6.
Other warranty rights and national law§ 1
This warranty does not exclude or limit the buyer’s statutory 1.
rights provided by national law, in particular, any such rights
against the seller that arise from a legally effective purchase
contract.
The warranty regulations mentioned herein are applicable un-2.
less they constitute an infringement of national warranty law.
Online registration§ 2
Please do remember to register your new BEHRINGER equipment right after your purchase by visiting www.behringer.com
(alternatively www.behringer.de) and kindly read the terms and
conditions of our warranty carefully.
Registering your purchase and equipment with us helps us process
your repair claims quicker and more efciently.
Thank you for your cooperation!
Warranty§ 3
BEHRINGER (BEHRINGER International GmbH including 1.
all BEHRINGER subsidiaries listed on the enclosed page,
except BEHRINGER Japan) warrants the mechanical and
electronic components of this product to be free of defects in
material and workmanship for a period of one (1) year* from
the original date of purchase, in accordance with the warranty
regulations described below. If the product shows any defects
within the specied warranty period that are not excluded from
this warranty as described under § 5, BEHRINGER shall, at its
discretion, either replace or repair the product using suitable
new or reconditioned parts. In the case that other parts are
used which constitute an improvement, BEHRINGER may,
at its discretion, charge the customer for the additional cost
of these parts.
If the warranty claim proves to be justied, the product will be 2.
returned to the user freight prepaid.
Warranty claims other than those indicated above are expressly 3.
excluded.
Return authorization number§ 4
To obtain warranty service, the buyer (or his authorized dealer) 1.
must call BEHRINGER (see enclosed list) during normal business hours BEFORE returning the product. All inquiries must
be accompanied by a description of the problem. BEHRINGER
will then issue a return authorization number.
Subsequently, the product must be returned in its original ship-2.
ping carton, together with the return authorization number to
the address indicated by BEHRINGER.
Shipments without freight prepaid will not be accepted.3.
Warranty regulations§ 5
Warranty services will be furnished only if the product is ac-1.
companied by a copy of the original retail dealer’s invoice. Any
product deemed eligible for repair or replacement under the
terms of this warranty will be repaired or replaced.
If the product needs to be modied or adapted in order to com-2.
ply with applicable technical or safety standards on a national
or local level, in any country which is not the country for which
the product was originally developed and manufactured, this
modication/adaptation shall not be considered a defect in
materials or workmanship. The warranty does not cover any
such modication/adaptation, irrespective of whether it was
carried out properly or not. Under the terms of this warranty,
BEHRINGER shall not be held responsible for any cost result-
ing from such a modication/adaptation.
Free inspections and maintenance/repair work are expressly 3.
excluded from this warranty, in particular, if caused by improper
handling of the product by the user. This also applies to defects caused by normal wear and tear, in particular, of faders,
crossfaders, potentiometers, keys/buttons, tubes, guitar strings,
illuminants and similar parts.
Damages/defects caused by the following conditions are not 4.
covered by this warranty:
improper handling, neglect or failure to operate the unit in =
compliance with the instructions given in BEHRINGER user
or service manuals.
connection or operation of the unit in any way that does not =
comply with the technical or safety regulations applicable
in the country where the product is used.
damages/defects caused by force majeure or any other =
condition that is beyond the control of BEHRINGER.
Any repair or opening of the unit carried out by unauthorized 5.
personnel (user included) will void the warranty.
If an inspection of the product by BEHRINGER shows that the 6.
defect in question is not covered by the warranty, the inspection
costs are payable by the customer.
Products which do not meet the terms of this warranty will be 7.
repaired exclusively at the buyer’s expense. BEHRINGER will
inform the buyer of any such circumstance. If the buyer fails to
submit a written repair order within 6 weeks after notication,
BEHRINGER will return the unit C.O.D. with a separate invoice
for freight and packing. Such costs will also be invoiced separately when the buyer has sent in a written repair order.
Warranty transferability§ 6
This warranty is extended exclusively to the original buyer (customer of retail dealer) and is not transferable to anyone who may
subsequently purchase this product. No other person (retail dealer,
etc.) shall be entitled to give any warranty promise on behalf of
BEHRINGER.
Claim for damages§ 7
Failure of BEHRINGER to provide proper warranty service shall
not entitle the buyer to claim (consequential) damages. In no
event shall the liability of BEHRINGER exceed the invoiced value
of the product.
* Customers in the European Union please contact BEHRINGER Germany Support
for further details.
Technical specications and appearance are subject to change without notice. The information contained herein is correct at the time of printing. BEHRINGER accepts no liability
for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. Colors and specications
may vary slightly from product. Our Products are sold through authorized dealers only. Distributors and dealers are not agents of BEHRINGER and have absolutely no authority
to bind BEHRINGER by any express or implied undertaking or representation. This manual is copyrighted. No part of this manual may be reproduced or transmitted in any form or
by any means, electronic or mechanical, including photocopying and recording of any kind, for any purpose, without the express written permission of BEHRINGER International
GmbH.
© 2008 BEHRINGER International GmbH, Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Muenchheide II, Germany,
ALL RIGHTS RESERVED.
Tel. +49 2154 9206 0, Fax +49 2154 9206 4903
Loading...