Behringer DSP1424P Ultramizer Pro Preset List

Presets (Factory Settings)

e

Nr. Name

Max. Out Level

Mode (C = Couple)

1 Heavy Pop C 0 100 25 12 -87 0 44 12.0 kHz 22 80 20 250 Hz
2 It’s 3D C 0 0 1 3 -87 0 20 12.0 kHz 25 85 100 100 Hz
3 The Wall C -1 100 32 24 -87 0 20 10.5 kHz 8 80 0 160 Hz
4 Mr. Enhancer C 0 0 1 0 -87 0 62 12.0 kHz 60 75 0 100 Hz
5 Analog Compressor C -1 70 85 5 -87 0 0 12.0 kHz 0 100 0 160 Hz
6 Disco C -1 32 66 9 -87 0 40 10.5 kHz 50 100 15 250 Hz
7 Heavy Denoiser C 0 15 43 0 -80 70 27 9.0 kHz 0 100 10 125 Hz
8 Light Denoiser C 0 24 50 1 -75 33 40 7.5 kHz 0 100 10 125 Hz

9 It’s Pop C 0 50 55 3 -87 0 29 9.0 kHz 18 80 30 125 Hz
10 The Drums C 0 70 83 6 -87 0 40 9.0 kHz 10 100 0 100 Hz
11 RMS Limiter C -14 (RMS) 50 20 24 -87 0 10 5.0 kHz 5 90 0 250 Hz
12 The Voice C -1 30 90 12 -60 10 53 5.0 kHz 0 90 0 2.0 kHz
13 Max. Headroom C 0 88 1 3 -82 10 0 12.0 kHz 0 100 0 0.8 kHz
14 Power to the people C -16 (RMS) 100 1 24 -75 10 0 12.0 kHz 0 100 0 0.8 kHz
15 Want it all ? C -1 60 1 12 -85 25 70 8.0 kHz 15 61 65 0.32 kHz
16 Pop / Enhance L 0 100 25 12 -87 0 44 12.0 kHz 22 80 - 250 Hz

17 Wall / Denoiser L -1 100 32 24 -87 0 20 10.5 kHz 8 80 - 160 Hz

18 RMS Limiter / Compressor L -14 (RMS) 50 20 24 -87 0 10 5.0 kHz 5 90 - 250 Hz

19 Limiter / Limiter L -14 (RMS) 50 20 24 -87 0 10 5.0 kHz 5 90 - 250 Hz

20 Compressor / Compressor L -1 70 85 5 -87 0 0 12.0 kHz 0 100 - 160 Hz

21 - 50 (Default) C 0 0 1 0 off 0 0 12.0 kHz 0 100 0 100 Hz

*) You can change the MAX. OUT LEVEL parameter from Peak to RMS mode by pressing the MAX. OUT LEVEL key for about 2 seconds.

R 0 0 1 0 -87 0 62 12.0 kHz 60 75 - 100 Hz

R 0 15 43 0 -80 70 27 9.0 kHz 0 100 - 125 Hz

R -1 70 85 5 -87 0 0 12.0 kHz 0 100 - 160 Hz

R -14 (RMS) 50 20 24 -87 0 10 5.0 kHz 5 90 - 250 Hz

R -1 70 85 5 -87 0 0 12.0 kHz 0 100 - 160 Hz

Ultramizer Speed

Ultramizer Density

Ultramizer Range

Denoiser Threshold

Denoiser Sensitivity

Exciter Process

Exciter Tune

Super Bass Process

Super Bass Tune

3D Surround Stereo Width

Crossover Frequency

MIDI Implementation

)XQFWLRQ 7UDQVPLWWHG 5HFRJQL]HG 5HPDUNV

Basic
Channel

Mode

Note Number

Velocity

After Touch
Pitch Bender X X

Control O 70 - 87 O 70 - 87 see add. Tabl
Progr.
Change
System Exclusive X X

System
Common

System
Real Time

Aux
Messages

Notes
O = YES, X = NO
Mode 1: OMNI ON, POLY
Mode 2: OMNI ON, MONO
Mode 3: OMNI OFF, POLY

ULTRAMIZER PRO DSP1424P

© 2002 BEHRINGER Spezielle Studiotechnik GmbH

Mode 4: OMNI OFF, MONO

0,',,PSOHP HQWDWLRQFKDUW

Default
Changed
Default
Messages
Altered

True Voic e
Note ON
Note OFF
Key´s
Ch´s

True #

Song Pos
Song Sel
Tune
Clock
Commands
Local O N/ O F F
All notes OFF
Active Sense
Reset

OFF, 1 - 16
OFF, 1 - 16
1,2,3,4
X
X
X
X
X
X
X
X

O (0-49)
1-50

X
X
X
X
X
X
X
X
X

OFF, 1 - 16
OFF, 1 - 16
1,2,3,4
X
X
X
X
X
X
X
X

O (0-49)
1-50

X
X
X
X
X
X
X
X
X

memorized

www.behringer.com

R

Controller Functions with MIDI

Parameter Name Display Range Midi Control

Control Value Range

Num ber

Max. Out Level -48 . . 0 70 0 .. 48

RMS Mode 71 0 = Peak, 1 = RMS

Stereo Width 0 .. 100 72 0 .. 100

Ultramizer Density 0 .. 100 73 0 .. 100

Ultramizer Speed 1 . . 100 74 0 . . 99

Ultramizer Range 0 .. 24 75 0 .. 24
Denoiser Threshold OF, -90 .. 0 76 0 .. 91
Denoiser Sensitivity 0..100 77 0 .. 100

Left / Right - 78 0 = coupled, 1 = L, 2 =

Exciter Process 0 . . 100 79 0 .. 100

Exciter Tune 4 .. 12 80 0 .. 100

Super Bass Process 0 .. 100 81 0 .. 100

Super Bass Tune 50 .. 150 82 0 .. 100

Crossover 20 (Hz) .. 20 (kHz) 83 0 . . 30

Low Mute - 84 0 = On, 1 = Mute

High Mute - 85 0 = On, 1 = Mute

Store - 86 0 .. 49

In / Out - 87 0 = Out, 1 = In

Quickguide

Connect the analogue outputs of the signal source (e.g. playback unit or mixing console) to the left and right inputs of your ULTRAMIZER PRO. Connect the
outputs of your DSP1424P to the analogue inputs of a recording device or a power amp. For use on single channels / subgroups on a mixing desk please
refer to chapter 3.6 in the English manual.

s Power up the ULTRAMIZER PRO. The last selected preset will automatically be loaded.

s Run a signal into your mixing console and assign it to the L/R master out.

s The two IN LED chains of your DSP1424P show the input signal level indB. Select the input sensitivity using the OPERATING LEVEL switch on the

rear panel (-10dBV semi-pro level used for home recording or the professional +4dBu studio level). If in doubt, please refer to the manufacturers
data for the unit which is connected to the DSP1424Ps inputs.

Setting the Max. Out Level

s Press the MAX. OUT LEVEL key and set the maximum output level using the JOG WHEEL. We suggest e.g. 0 dB as a brick wall limiter. Nothing will

go over this level.

Setting the Ultramizer

+ When the EXCITER and SUPERBASS keys are pressed simultaneously, the crossover frequency between the lower and higher

bands of the multiband compressor can be adjusted from 20Hz to 20kHz. If you need to, you can mute either low or high band by
pressing the respective key for more than 2 seconds (all GR LEDs for the muted band will blink in time).

s If you press the ULTRAMIZER key once, you have access to the parameter DENSITY. Use the JOG WHEEL to set this parameter. The higher the

value, the more gain reduction is achieved.

s After pressing the ULTRAMIZER key a second time, the parameter SPEED can be set with the JOG WHEEL. Choose a slow speed (large value) when

the Ultramizer must do its job inaudibly and high speed (small value) when fast recovery from transients is necessary.

s The parameter RANGE, which you access after pressing the ULTRAMIZER key a third time, determines the maximum gain the Ultramizer function will

apply to the signal. The actual amount of gain being applied to the signal is also dependent on the Max. Out Level.

Setting the Exciter

s When the EXCITER key is pressed once you gain access to the PROCESS parameter. Use the JOG WHEEL to set the intensity of the Exciter effect

between 0 and 100.

s When pressed twice you have access to the TUNE parameter. This is the lower frequency limit of the Exciter function. This can be set from

4 to 12 kHz using the JOG WHEEL.

Setting the Super Bass

s The SuperBass function is the low frequency equivalent of the Exciter function. After pressing the SUPER BASS key once, you can adjust the

PROCESS parameter. Press this key again to TUNE the cut-off frequency. This is the highest frequency affected by the Super Bass function.

Setting 3DSurround

s First of all, ensure that couple mode is activated i.e. both LEFT and RIGHT keys are lit simultaneously. Do this by pressing and holding both of these

keys together for a second or two. The depth of the 3D Surround function is determined by only the PROCESS parameter, which can be set using
the JOG WHEEL.

Setting the Denoiser

s When the DENOISER key is pressed once, the THRESHOLD can be set. This function is used to remove unwanted noise. The higher the value, the

more effective the denoiser.

s When the DENOISER key is pressed a second time you can edit the parameter SENSITIVITY. With this parameter you determine the sensitivity of the

Denoiser.

Saving edits

s After editing, the flashing PRESET key reminds you that the preset settings have been changed but not saved yet. Press this key once. The display

reads the current patch number. When pressed again, this number starts flashing. If you need to retain the original patch, use the JOG WHEEL to
save to another patch, one which can be overwritten. Press the PRESET key a third time to save the edits to the selected patch.

© 2002 BEHRINGER Spezielle Studiotechnik GmbH