AT&T 902 User Manual
User’s Manual for the
• Try calling the number you want
to enter into memory. When the
call is ended, press ,
and a memory button.
• If someone lifts an extension
phone while you are storing numbers in memory, programming
might be interrupted. Make sure
all extensions are on hook while
storing numbers in memory.
• You might not hear the confirma-
tion beep if the RECEIVER
(handset) volume is set too low, or
if you are in a noisy location.
• If the number is more than 24
digits long, make sure you follow
the directions for “Dialing Long
Numbers.”
• Do not put the phone on Hold
while storing numbers.
Problems With Line Status Lights
• Make sure all plugs are connected
properly. Inspect the line cord
connections at the modular jack
and at the telephone. Also inspect
the coiled handset cord connections
at both ends.
• Try replacing old bat t e ries. See
“ B at t e ri e s ” in the Installation section.
• Make sure the batteries are
correctly installed, and that the
battery contact surfaces and
battery case are clean.
• If only one telephone line is
connected, make sure that only the
batteries for that line (as labeled
on the battery compartment) are
installed.
Telephone Does Not Ring
• Make sure the RINGER switch
is set in the LO or HI position.
• If there are several other
telephones on the same line, try
disconnecting some of the other
telephones. Having too many
telephones connected can also
create problems such as low ringer
volume, or impaired sound quality
during calls.
Other Problems
Make sure you have followed all the
instructions in this booklet. If you
continue to have problems, call
1 800 722-9125. If you cannot
correct the problem, disconnect the
telephone and refer to the warranty
information.
Two-Line Speakerphone 902
Fold open this manual for information about
this telephone’s installation and operation.
Please read Part 1 — Important Product
Information, included in this package.
Part 2
© 1998 Philips Consumer Communications, L.P. All rights reserved.
Printed in Mexico. 848236212 Issue 1AT&T
IN CASE OF DIFFICULT Y
I N S TA L L AT I O N
NOTE: This telephone requires a
2-line modular jack or two separate
one-line modular jacks to use this
unit as a two-line phone.
NOTE: To use both lines of a twoline telephone, your local telephone
company must provide two telephone
numbers.
Batteries
B e fo re using the telep h o n e, yo u
should install AA bat t e ries (not
i n cluded). If you are connecting
o n ly Line 1 or only Line 2, use two
b at t e ri e s , as indicated on the bottom of
the phone. If you are connecting both
l i n e s , use four bat t e ri e s .
You can use the phone without
batteries to make and receive calls,
but it requires batteries to power the
Line Status lights.
If you have wall-mounted the
telephone, follow these directions:
1 Remove the telephone from
the wall.
2 Turn the telephone upside down.
3 Remove the base by pressing the
tabs located on the top of the base.
4 Press down on tab on battery
door located between arrows on
battery door (Figure 2A). Swing
door open and insert new batteries
(Figure 2B).
5 Close the battery door.
C AU T I O N : A lways unplug the line
c o rd befo re installing new AA bat t e ri e s .
Figure 2B
Figure 2A
Line Status
Lights
Line selection
Programs a number
in memory
Programs a pause
in memory
Conferences
both lines
Accesses memory
dialing numbers
Directory Card/Cover
Line 2 Ringer Volume
Line 1 Ringer Volume
Access Call Waiting
or other services
Handset
Temporary
Tone
Press down on tab to
open battery door
Insert 2
AA batteries
for Line 2
Figure 1
BATTERY DOOR CLOSED, BASE OFF
BATTERY DOOR OPEN, BASE OFF
Puts a call on hold
Mutes a call
Redials last call made, or starts Auto Redial
Speaker/Handset Volume
Turn speaker on or off
Insert 2
AA batteries
for Line 1
Figure 3
Loading...