ASRock IMB-1211-D, IMB-1211-L, IMB-1210-D, IMB-1210-L User Manual

IMB-1211-D

IMB-1211-L

IMB-1210-D

IMB-1210-L

User Manual

Version 1.1

Updated September 3, 2020

Version 1.1

Updated September 3, 2020

No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Pract ices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate”

ASRock Website: http://www.asrock.com

CAUTION:

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTER IES ACCOR DING TO THE INSTRUCTIONS.

Contents

1 Introduction ....................................................... 5

1.1 Package Contents ......................................................... 5

1.2 Specications ................................................................. 6

1.3 Motherboard Layout ....................................................... 14

1.4 I/O Panel ........................................................................ 16

2 Installation ......................................................... 20

2.1 Screw Holes ................................................................... 20

2.2 Pre-installation Precautions ........................................... 20

2.3 Installation of Memory Modules (SO-DIMM) .................. 21

2.4 Expansion Slots ............................................................ 23

2.5 Jumpers Setup ............................................................... 25

2.6 Onboard Headers and Connectors ................................ 28

3 UEFI SETUP UTILITY ......................................... 33

3.1 Introduction .................................................................... 33

3.1.1 UEFI Menu Bar .................................................... 33

3.1.2 Navigation Keys ................................................... 34

3.2 Main Screen ................................................................... 34

3.3 Advanced Screen ........................................................... 35

3.3.1 CPU Conguration ............................................... 36

3.3.2 Chipset Conguration........................................... 38

3.3.3 Storage Conguration .......................................... 40

3.3.4 Super IO Conguration ........................................ 41

3.3.5 AMT Conguration ............................................... 42

3.3.6 ACPI Conguration............................................... 44

3.3.7 USB Conguration ............................................... 45

3.3.8 Trusted Computing ............................................... 46

3.4 Hardware Health Event Monitoring Screen ................... 47

3.5 Security Screen ............................................................. 48

3.6 Boot Screen ................................................................... 49

3.7 Exit Screen .................................................................... 51

4 Software Support .............................................. 52

4.1 Install Operating System ................................................ 52

4.2 Support CD Information ................................................. 52

4.2.1 Running Support CD ............................................ 52

4.2.2 Drivers Menu ........................................................ 52

4.2.3 Utilities Menu........................................................ 52

4.2.4 Contact Information .............................................. 52

Chapter 1: Introduction

Thank you for purchasing ASRock

1210-L

motherboard, a reliable motherboard produced under ASRock’s consistently

stringent quality control. It delivers excellent performance with robust design con-

forming to ASRock’s commitment to quality and endurance.

In this manual, chapter 1 and 2 contain introduction of the motherboard and step-

by-step guide to the hardware installation. Chapter 3 and 4 contain the conguration

guide to BIOS setup and information of the Support CD.

Because the motherboard specications and the BIOS software might be

updated, the content of this manual will be subject to change without no-

tice. In case any modications of this manual occur, the updated version

will be available on ASRock website without further notice. You may nd

the latest VGA cards and CPU support lists on ASRock website as well.

ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for specic information about the model you are using.

www.asrock.com/support/index.asp

1.1 Package Contents

ASRock

(Mini-ITX Form Factor: 6.7-in x 6.7-in, 17.0 cm x 17.0 cm)

ASRock

struction

1 x I/O Panel Shield

IMB-1211-D / IMB-1211-L / IMB-1210-D / IMB-1210-L

IMB-1211-D / IMB-1211-L / IMB-1210-D / IMB-

Motherboard

Driver CD

Jumper setting in-

1.2 Specications

IMB-1211-D:

Form Factor

Processor System

Expansion Slot

Memory

Graphics

Ethernet

Dimensions Mini-ITX (6.7-in x 6.7-in)

Socket LGA 1151 for 9th/8th Intel® Core i7/i5/i3/

CPU

Chipset Intel® Q370 PCIe 1 x PCIe x16

Mini-PCIe 1 x Full/Half mini-PCIe with PCIe x1 and USB 2.0 mSATA N/A

M.2

Technology Dual Channel DDR4 2400/2666 MHz

Max.

Socket 2 x SO-DIMM Controller Intel® HD Graphics (By CPU) VGA N/A DVI N/A LVDS N/A HDMI N/A

DisplayPort

MultiDisplay Triple Display

eDP

Ethernet 10/100/1000 Mbps Controller 1 x Intel® I210, 1 x Intel® I219LM

Celeron (Supports up to 65W) * The Performance of CPUs over 65W will be limited due to power design.

1x M.2 (Key E, 2230) with PCIe x1, CNVI and USB2.0 for Wireless 1x M.2 (Key M, 2242/2260/2280) with PCIe x4 and SATA3 for SSD

64GB* * Intel® Core i9/i7/i5 CPUs support up to 64GB (32GB per DIMM) Intel® Core i3/Pentium®/Celeron® CPUs support up to 32GB (16GB per DIMM)

Supports max resolution up to 4096x2304@60Hz

Rear I/O

Internal Connector

Watchdog Timer

Power Requirements

Environment

VGA N/A HDMI N/A DisplayPort 3 Ethernet 2 USB 4 x USB support USB3.1 Audio 2 (Mic-in, Line-out) Serial 2 x COM(RS-232/422/485)

PS2 N/A

USB 4 x USB 2.0 LVDS/ inverter eDP 1 VGA N/A Serial 3 x COM(RS-232) SATA 4 x SATA3 (6.0Gb/s) GPIO 4 x GPI, 4 x GPO SATA PWR Output Speaker Header TPM 1 x Onboard TPM 2.0 IC Output From super I/O to drag RESETCON# Interval 256 Segments, 0,1,2…255 Sec Input PWR ATX PWR 24+4-pin

Power On

Operating Temp Storage Temp

N/A

AT/ATX Supported AT: Directly PWR on as Power input ready ATX: Press Button to PWR on after Power input ready

0ºC – 60ºC

-40ºC – 85ºC

IMB-1211-L:

Form Factor

Processor System

Expansion Slot

Memory

Graphics

Ethernet

Dimensions Mini-ITX (6.7-in x 6.7-in)

Socket LGA 1151 for 9th/8th Intel® Core i7/i5/i3/

CPU

Chipset Intel® Q370 PCIe 1 x PCIe x16

Mini-PCIe 1 x Full/Half mini-PCIe with PCIe x1 and USB 2.0 mSATA N/A

M.2

Technology Dual Channel DDR4 2400/2666 MHz

Max.

Socket 2 x SO-DIMM Controller Intel® HD Graphics (By CPU)

VGA

DVI N/A

LVDS

HDMI N/A

DisplayPort

MultiDisplay Triple Display eDP N/A Ethernet 10/100/1000 Mbps Controller 1 x Intel® I210, 1 x Intel® I219LM

Celeron (Supports up to 65W) * The Performance of CPUs over 65W will be limited due to power design.

1x M.2 (Key E, 2230) with PCIe x1, CNVI and USB2.0 for Wireless 1x M.2 (Key M, 2242/2260/2280) with PCIe x4 and SATA3 for SSD

64GB* * Intel® Core i9/i7/i5 CPUs support up to 64GB (32GB per DIMM) Intel® Core i3/Pentium®/Celeron® CPUs support up to 32GB (16GB per DIMM)

Supports max resolution up to 1920x1200@60Hz

Supports max resolution up to 4096x2304@60Hz

Rear I/O

Internal Connector

Watchdog Timer

Power Requirements

Environment

VGA 1 HDMI N/A DisplayPort 2 Ethernet 2 USB 4 x USB support USB3.1 Audio 2 (Mic-in, Line-out) Serial 2 x COM(RS-232/422/485) PS2 N/A USB 4 x USB 2.0 LVDS/ inverter eDP N/A VGA N/A Serial 3 x COM(RS-232) SATA 4 x SATA3 (6.0Gb/s) GPIO 4 x GPI, 4 x GPO SATA PWR Output Speaker Header TPM 1 x Onboard TPM 2.0 IC Output From super I/O to drag RESETCON# Interval 256 Segments, 0,1,2…255 Sec Input PWR ATX PWR 24+4-pin

Power On

Operating Temp Storage Temp

N/A

AT/ATX Supported AT: Directly PWR on as Power input ready ATX: Press Button to PWR on after Power input ready

0ºC – 60ºC

-40ºC – 85ºC

IMB-1210-D:

Form Factor

Processor System

Expansion Slot

Memory

Graphics

Ethernet

Dimensions Mini-ITX (6.7-in x 6.7-in)

Socket LGA 1151 for 9th/8th Intel® Core i7/i5/i3/

CPU

Chipset PCIe 1 x PCIe x16

Mini-PCIe 1 x Full/Half mini-PCIe with PCIe x1 and USB 2.0 mSATA N/A

M.2

Technology Dual Channel DDR4 2400/2666 MHz

Max.

Socket 2 x SO-DIMM Controller Intel® HD Graphics (By CPU) VGA N/A DVI N/A LVDS N/A HDMI N/A

DisplayPort

MultiDisplay Dual Display

eDP

Ethernet 10/100/1000 Mbps Controller 1 x Intel® I210, 1 x Intel® I219V

Celeron (Supports up to 65W) * The Performance of CPUs over 65W will be limited due to power design. Intel® H310

1x M.2 (Key E, 2230) with PCIe x1, CNVI and USB2.0 for Wireless 1x M.2 (Key M, 2242/2260/2280) with shared SATA3 for SSD

64GB* * Intel® Core i9/i7/i5 CPUs support up to 64GB (32GB per DIMM) Intel® Core i3/Pentium®/Celeron® CPUs support up to 32GB (16GB per DIMM)

Supports max resolution up to 4096x2304@60Hz

Rear I/O

Internal Connector

Watchdog Timer

Power Requirements

Environment

VGA N/A HDMI N/A DisplayPort 3 Ethernet 2 USB 4 x USB support USB3.1 Audio 2 (Mic-in, Line-out)

Serial

PS2 N/A USB 4 x USB 2.0 LVDS/ inverter eDP 1 VGA N/A Serial 2 x COM(RS-232)

SATA

GPIO 4 x GPI, 4 x GPO SATA PWR Output Speaker Header TPM 1 x Header Output From super I/O to drag RESETCON# Interval 256 Segments, 0,1,2…255 Sec Input PWR ATX PWR 24+4-pin

Power On

Operating Temp Storage Temp

1 x COM(RS-232/422/485), 1 x COM (RS-

232)

N/A

4 x SATA3 (6.0Gb/s), one is shared with M.2 Key M

N/A

AT/ATX Supported AT: Directly PWR on as Power input ready ATX: Press Button to PWR on after Power input ready

0ºC – 60ºC

-40ºC – 85ºC

IMB-1210-L:

Form Factor

Processor System

Expansion Slot

Memory

Graphics

Ethernet

Dimensions Mini-ITX (6.7-in x 6.7-in)

Socket LGA 1151 for 9th/8th Intel® Core i7/i5/i3/

CPU

Chipset Intel® H310 PCIe 1 x PCIe x16

Mini-PCIe 1 x Full/Half mini-PCIe with PCIe x1 and USB 2.0 mSATA N/A

M.2

Technology Dual Channel DDR4 2400/2666 MHz

Max.

Socket 2 x SO-DIMM Controller Intel® HD Graphics (By CPU)

VGA

DVI N/A

LVDS

HDMI N/A

DisplayPort

MultiDisplay Dual Display eDP N/A Ethernet 10/100/1000 Mbps Controller 1 x Intel® I210, 1 x Intel® I219V

Celeron (Supports up to 65W) * The Performance of CPUs over 65W will be limited due to power design.

1x M.2 (Key E, 2230) with PCIe x1, CNVI and USB2.0 for Wireless 1x M.2 (Key M, 2242/2260/2280) with shared SATA3 for SSD

64GB* * Intel® Core i9/i7/i5 CPUs support up to 64GB (32GB per DIMM) Intel® Core i3/Pentium®/Celeron® CPUs support up to 32GB (16GB per DIMM)

Supports max resolution up to 1920x1200@60Hz

Supports max resolution up to 4096x2304@60Hz

Rear I/O

Internal Connector

Watchdog Timer

Power Requirements

Environment

VGA 1 HDMI N/A DisplayPort 2 Ethernet 2 USB 4 x USB support USB3.1 Audio 2 (Mic-in, Line-out)

Serial

PS2 N/A USB 4 x USB 2.0 LVDS/ inverter eDP N/A VGA N/A Serial 2 x COM(RS-232)

SATA

GPIO 4 x GPI, 4 x GPO SATA PWR Output Speaker Header TPM 1 x Header Output From super I/O to drag RESETCON# Interval 256 Segments, 0,1,2…255 Sec Input PWR ATX PWR 24+4-pin

Power On

Operating Temp Storage Temp

1 x COM(RS-232/422/485), 1 x COM (RS-

232)

4 x SATA3 (6.0Gb/s), one is shared with M.2 Key M

N/A

AT/ATX Supported AT: Directly PWR on as Power input ready ATX: Press Button to PWR on after Power input ready

0ºC – 60ºC

-40ºC – 85ºC

1.3 Motherboard Layout

1 : COM Port PWR Setting Jumpers PWR_COM3 (For COM Port3) PWR_COM4 (For COM Port4) 2 : Backlight Power Select (LCD_BLT_VCC) (BKT_PWR1) 3 : BL1 4 : Inverter Power Control Wafer (BLT_PWR1) 5* :

LVDS Panel Connector * eDP Connector 6 : BL2 7 : Buzzer 8 : Panel Power Select (LCD_VCC) (PNL_PWR1) 9 : Backlight Volume Control (BLT_VOL1) 10* : COM Port Headers (COM1, 2, 5)

(COM5 is for IMB-1211-D / IMB-1211-L only) (COM1, COM2, COM5 support RS232 only) 11 :

Digital Input / Output

12 :

4-Pin Chassis FAN Connector (+12V) 13 : 24-pin ATX Power Input Connector 14 : ATX/AT Mode Jumper (SIO_AT1) 15 :

System Panel Header 16 : LPC Header 17 : Digital Input / Output Power Select (JGPIOPWR) (JGPIO_PWR1) 18 : Digital Input/Output Pin Header (JGPIO1) 19* : COM Port PWR Setting Jumpers (PWR_COM5 PWR_COM1 (For COM Port1) PWR_COM2 (For COM Port2) PWR_COM5 (For COM Port5) 20 :

Chassis Intrusion Header (CI1) 21 : 4-pin ATX Power Input/Output Connector 22 : PWR_BAT1 23 :

USB2.0 Headers ( 24 : Clear CMOS Headers (CLRMOS1, CLRMOS2) 25 : M.2 Select (M2_SEL1) (For IMB-1210-D / IMB-1210-L only) 2

6 : 3W Audio AMP Output Wafer

27 :

Front Panel Audio Header 28 : SATA3 Connectors (SATA3_1~4) 29 : USB Power Setting Jumpers (USB2_PWR_H1 (For USB2_5_6)) (USB2_PWR_H2 (For USB2_7_8)) (USB3_PWR1 (For 30 :

4-Pin CPU FAN Connector (+12V) (CPU_FAN1)

is for IMB-1211-D / IMB-1211-L only)

(For IMB-1210-L / IMB-1211-L only)

(For IMB-1210-D / IMB-1211-D only) (

Default Value Setting (JGPIO_SET1)

USB2_5_6, USB2_7_8

USB3_1_2

))

)

on the Backside of PCB)

* IMB-1211-D / IMB-1210-D supports DisplayPort on the rear I/O panel. IMB-1211-L / IMB-1210-L supports VGA port on the rear I/O panel.

Back Side : M.2 Socket ( * M2_2 supports either PCIe or SATA mode for IMB-1211-D. M2_2 supports SATA mode only for IMB-1210-L. * M2_2 and SATA3_1 share lanes. If either one of them is in use, the other one will be disabled.

Key-M)

(M2_2) :

1.4 I/O Panel

IMB-1211-D:

1 COM Port (COM3) (RS232/422/485)*

2 DisplayPort (DP1)

3 LAN RJ-45 Port**

4 LAN RJ-45 Port**

5 Line out (Lime)

6 Microphone (Pink)

* This motherboard supports RS232/422/485 on COM3, 4 ports. Please refer to below table for

the pin denition. In addition, COM3, 4 ports (RS232/422/485) can be adjusted in BIOS setup

utility > Advanced Screen > Super IO Conguration. You may refer to page 41 for details.

PIN RS232 RS422 RS485

1 DCD TX- RTX2 RXD RX+ N/A 3 TXD TX+ RTX+ 4 DTR RX- N/A 5 GND GND GND 6 DSR N/A N/A 7 RTS N/A N/A 8 CTS N/A N/A 9 +5V / +12V N/A N/A

COM3, 4 Port Pin Denition

7 USB 3.0 Ports (USB3_3_4) (Only +5VSB)

8 USB 3.0 Ports (USB3_1_2)

9 DisplayPort (DP3)

10 DisplayPort (DP2)

11 COM Port (COM4) (RS232/422/485)*

** There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

Activity/Link LED SPEED LED

Status Description Status Description

LAN Port LED Indications

ACT/LINK

LED

SPEED

LED

O󰀨 No Link O󰀨 10Mbps connection

Blinking Data Activity Orange 100Mbps connection

On Link Green 1Gbps connection

LAN Port

+ 36 hidden pages