ASRock 980DE3, 980U3S3 User Manual [en, ru, de, es, fr, it]

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans­lated in any language, in any form or by any means, except duplication of documentation
by the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identica­tion or explanation and to the owners’ benet, without intent to infringe.

Disclaimer:

Specications and information contained in this guide are furnished for informational use

only and subject to change without notice, and should not be constructed as a commit­ment by ASRock. ASRock assumes no responsibility for any errors or omissions that may
appear in this guide.
With respect to the contents of this guide, ASRock does not provide warranty of any kind,
either expressed or implied, including but not limited to the implied warranties or condi-

tions of merchantability or tness for a particular purpose. In no event shall ASRock, its
directors, ofcers, employees, or agents be liable for any indirect, special, incidental, or
consequential damages (including damages for loss of prots, loss of business, loss of

data, interruption of business and the like), even if ASRock has been advised of the pos­sibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published June 2013

Copyright©2013 ASRock INC. All rights reserved.

ASRock 980DE3/U3S3 Motherboard

English

1

Motherboard Layout

English

2

1 ATX 12V Power Connector (ATX12V1) 20 SATA2 Connector (SATA2_1 (PORT 1))
2 Power Fan Connector (PWR_FAN1) 21 USB 2.0 Header (USB6_7)
3 CPU Fan Connector (CPU_FAN1) 22 USB 2.0 Header (USB4_5)
4 AM3+ CPU Socket 23 USB 2.0 Header (USB8_9)
5 CPU Heatsink Retention Module 24 System Panel Header (PANEL1)
6 2 x 240-pin DDR3 DIMM Slots 25 Power LED Header (PLED1)
(Dual Channel: DDR3_A1, DDR3_B1) 26 Chassis Speaker Header (SPEAKER1)
7 2 x 240-pin DDR3 DIMM Slots 27 Floppy Connector (FLOPPY1)
(Dual Channel: DDR3_A2, DDR3_B2) 28 Internal Audio Connector (CD1)
8 Northbridge Controller 29 Front Panel Audio Header (HD_AUDIO1)
9 SATA3 Connector (SATA3_2 (PORT 7)) 30 HDMI_SPDIF Header (HDMI_SPDIF1)
10 ATX Power Connector (ATXPWR1) 31 Infrared Module Header (IR1)
11 SATA3 Connector (SATA3_1 (PORT 6)) 32 PCI Slots (PCI1-2)
12 Chassis Fan Connector (CHA_FAN1) 33 PCI Express 2.0 x1 Slot (PCIE4)
13 Southbridge Controller 34 PCI Express 2.0 x16 Slot (PCIE3)
14 SPI Flash Memory (16Mb) 35 PCI Express 2.0 x1 Slot (PCIE2)
15 SATA2 Connector (SATA2_6 (PORT 5)) 36 IDE1 Connector (IDE1)
16 SATA2 Connector (SATA2_5 (PORT 4)) 37 PCI Express 2.0 x1 Slot (PCIE1)
17 SATA2 Connector (SATA2_4 (PORT 3)) 38 Clear CMOS Jumper (CLRCMOS1)
18 SATA2 Connector (SATA2_3 (PORT 2)) 39 USB 3.0 Header (USB3_2_3)
19 SATA2 Connector (SATA2_2 (PORT 1))

ASRock 980DE3/U3S3 Motherboard

I/O Panel

1 PS/2 Mouse Port (Green) 6 USB 2.0 Ports (USB01)
* 2 LAN RJ-45 Port 7 USB 3.0 Port (USB01)
3 Line In (Light Blue) 8 USB 2.0 Ports (USB23)
** 4 Front Speaker (Lime) 9 Serial Port: COM1
5 Microphone (Pink) 10 PS/2 Keyboard Port (Purple)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED
indications.

Activity/Link LED SPEED LED

Status Description Status Description

Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

LAN Port LED Indications

ACT/LINK
LED

LAN Port

SPEED
LED

** To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. Please refer to below steps for the software setting of Multi-Streaming.
For Windows® XP:

After restarting your computer, you will nd “Mixer” tool on your system. Please select “Mixer

ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or

“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker
and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then
reboot your system.
For Windows® 8 / 7 / VistaTM:
After restarting your computer, please double-click “Realtek HD Audio Manager” on the

system tray. Set “Speaker Conguration” to “Quadraphonic” or “Stereo”. Click “Device

advanced settings”, choose “Make front and rear output devices playbacks two different audio
streams simultaneously”, and click “ok”. Then reboot your system.

ASRock 980DE3/U3S3 Motherboard

English

3

1. Introduction

Thank you for purchasing ASRock 980DE3/U3S3 motherboard, a reliable mother­board produced under ASRock’s consistently stringent quality control. It delivers
excellent performance with robust design conforming to ASRock’s commitment to
quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found
in the user manual presented in the Support CD.

Because the motherboard specications and the BIOS software might

be updated, the content of this manual will be subject to change without
notice. In case any modications of this manual occur, the updated ver­sion will be available on ASRock website without further notice. You may

nd the latest VGA cards and CPU support lists on ASRock website as

well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for specic information about the model you are using.

www.asrock.com/support/index.asp

1.1 Package Contents

ASRock 980DE3/U3S3 Motherboard (ATX Form Factor)
ASRock 980DE3/U3S3 Quick Installation Guide
ASRock 980DE3/U3S3 Support CD
2 x Serial ATA (SATA) Data Cables (Optional)
1 x I/O Panel Shield

English

4

ASRock Reminds You...

To get better performance in Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM
/ VistaTM 64-bit, it is recommended to set the BIOS option in Storage

Conguration to AHCI mode. For the BIOS setup, please refer to the “User

Manual” in our support CD for details.

ASRock 980DE3/U3S3 Motherboard

1.2 Specications

Platform - ATX Form Factor

- All Solid Capacitor design
CPU - Support for Socket AM3+ processors

- Support for Socket AM3 processors: AMD PhenomTM II X6 /
X4 / X3 / X2 (except 920 / 940) / Athlon II X4 / X3 / X2 /
Sempron processors

- Supports 8-Core CPU

- Digi Power Design

- Supports CPU up to 140W

- Supports AMD OverDriveTM with ACC feature (Advanced
Clock Calibration)

- Supports AMD’s Cool ‘n’ QuietTM Technology

- FSB 2600 MHz (5.2 GT/s)

- Supports Untied Overclocking Technology

- Supports Hyper-Transport 3.0 (HT 3.0) Technology
Chipset - Northbridge: AMD RX881/760G

- Southbridge: AMD SB710
Memory - Dual Channel DDR3 Memory Technology

- 4 x DDR3 DIMM slots

- Support DDR3 1866(OC)/1600(OC)/1333/1066/800
non-ECC, un-buffered memory (see CAUTION 1)

- Max. capacity of system memory: 32GB (see CAUTION 2)
Expansion Slot - 1 x PCI Express 2.0 x16 slot (PCIE3 @ x16 mode)

- 3 x PCI Express 2.0 x1 slots

- 2 x PCI slots

Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec)
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supports Wake-On-LAN

- Supports LAN Cable Detection

- Supports Energy Efcient Ethernet 802.3az

- Supports PXE
Rear Panel I/O I/O Panel

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Serial Port: COM1

- 4 x Ready-to-Use USB 2.0 Ports

- 2 x Ready-to-Use USB 3.0 Ports

English

ASRock 980DE3/U3S3 Motherboard

5

English

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)

- HD Audio Jack: Line in / Front Speaker / Microphone
SATA3 - 2 x SATA3 6.0 Gb/s connectors by ASMedia ASM1061,

support NCQ, AHCI and Hot Plug

USB 3.0 - 2 x Rear USB 3.0 ports by Etron EJ188, support
USB 1.1/2.0/3.0 up to 5Gb/s

- 1 x Front USB 3.0 header by Etron EJ188 (supports 2
USB 3.0 ports), supports USB 1.1/2.0/3.0 up to 5Gb/s
Connector - 6 x SATA2 3.0 Gb/s connectors, support RAID (RAID 0,

RAID 1, RAID 10 and JBOD), NCQ, AHCI and “Hot Plug”

functions

- 2 x SATA3 6.0Gb/s connectors

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x HDMI_SPDIF header

- 1 x Power LED header

- 1 x CPU Fan connector (4-pin)

- 1 x Chassis Fan connector (4-pin)

- 1 x Power Fan connector (4-pin)

- 24 pin ATX power connector

- 8 pin 12V power connector

- CD in header

- Front panel audio connector

- 3 x USB 2.0 headers (support 6 USB 2.0 ports)

- 1 x USB 3.0 header (supports 2 USB 3.0 ports)
BIOS Feature - 16Mb AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

- CPU, VCCM, NB Voltage Multi-adjustment
Support CD - Drivers, Utilities, AntiVirus Software (Trial Version),
CyberLink MediaEspresso 6.5 Trial, Google Chrome
Browser and Toolbar
Hardware - CPU Temperature Sensing
Monitor - Chassis Temperature Sensing

- CPU/Chassis/Power Fan Tachometer

- CPU Quiet Fan

6

ASRock 980DE3/U3S3 Motherboard

- CPU/Chassis/Power Fan Multi-Speed Control

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore
OS - Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista
VistaTM 64-bit / XP / XP Media Center / XP 64-bit compliant

Certications - FCC, CE, WHQL

- ErP/EuP Ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with overclocking,
including adjusting the setting in the BIOS, applying Untied Overclocking
Technology, or using third-party overclocking tools. Overclocking may
affect your system’s stability, or even cause damage to the components
and devices of your system. It should be done at your own risk and
expense. We are not responsible for possible damage caused by
overclocking.

TM

/

CAUTION!

1. Whether 1866/1600MHz memory speed is supported depends
on the AM3/AM3+ CPU you adopt. If you want to adopt DDR3
1866/1600 memory module on this motherboard, please refer
to the memory support list on our website for the compatible
memory modules.

ASRock website: http://www.asrock.com

2. Due to the operating system limitation, the actual memory size
may be less than 4GB for the reservation for system usage un­der Windows® 8 / 7 / VistaTM / XP. For Windows® 64-bit OS with
64-bit CPU, there is no such limitation.

ASRock 980DE3/U3S3 Motherboard

English

7

1.3 Unique Features

ASRock OC Tuner

ASRock OC Tuner is a user-friendly overclocking tool which al-

lows you to surveil your system by hardware monitor function
and overclock your hardware devices to get the best system
performance under Windows® environment. Please visit our
website for the operation procedures of ASRock OC Tuner.

ASRock Intelligent Energy Saver

Featuring an advanced proprietary hardware and software de-

sign, Intelligent Energy Saver is a revolutionary technology that
delivers unparalleled power savings. The voltage regulator can

reduce the number of output phases to improve efciency when

the CPU cores are idle. In other words, it is able to provide ex­ceptional power saving and improve power efficiency without
sacrificing computing performance. To use Intelligent Energy

Saver function, please enable Cool ‘n’ Quiet option in the BIOS

setup in advance. Please visit our website for the operation pro­cedures of Intelligent Energy Saver.

ASRock Instant Boot

ASRock Instant Boot allows you to turn on your PC in just a few

seconds, provides a much more efcient way to save energy,

time, money, and improves system running speed for your sys­tem. It leverages the S3 and S4 ACPI features which normally
enable the Sleep/Standby and Hibernation modes in Windows®

to shorten boot up time. By calling S3 and S4 at specic timing

during the shutdown and startup process, Instant Boot allows
you to enter your Windows® desktop in a few seconds.

English

8

ASRock Instant Flash

ASRock Instant Flash is a BIOS ash utility embedded in Flash

ROM. This convenient BIOS update tool allows you to update

system BIOS without entering operating systems rst like MS-

DOS or Windows®. With this utility, you can press the <F6> key
during the POST or the <F2> key to enter into the BIOS setup
menu to access ASRock Instant Flash. Just launch this tool and

save the new BIOS le to your USB ash drive, oppy disk or

hard drive, then you can update your BIOS only in a few clicks

without preparing an additional oppy diskette or other

ASRock 980DE3/U3S3 Motherboard

complicated flash utility. Please be noted that the USB flash

drive or hard drive must use FAT32/16/12 le system.

ASRock OC DNA

The software name itself – OC DNA literally tells you what it is

capable of. OC DNA, an exclusive utility developed by ASRock,
provides a convenient way for the user to record the OC set­tings and share with others. It helps you to save your overclock­ing record under the operating system and simplies the compli­cated recording process of overclocking settings. With OC DNA,

you can save your OC settings as a prole and share with your
friends! Your friends then can load the OC prole to their own

system to get the same OC settings as yours! Please be noticed

that the OC prole can only be shared and worked on the same

motherboard.

ASRock APP Charger

If you desire a faster, less restricted way of charging your

Apple devices, such as iPhone/iPad/iPod Touch, ASRock has
prepared a wonderful solution for you - ASRock APP Charger.
Simply install the APP Charger driver, it makes your iPhone
charge much quickly from your computer and up to 40% faster
than before. ASRock APP Charger allows you to quickly charge
many Apple devices simultaneously and even supports continu­ous charging when your PC enters into Standby mode (S1),
Suspend to RAM (S3), hibernation mode (S4) or power off (S5).
With APP Charger driver installed, you can easily enjoy the mar­velous charging experience.

ASRock XFast USB

ASRock XFast USB can boost USB storage device perfor-

mance. The performance may depend on the properties of the
device.

ASRock XFast LAN

ASRock XFast LAN provides a faster internet access, which

includes the benefits listed below. LAN Application Prioritiza-

tion: You can congure your application’s priority ideally and/or

add new programs. Lower Latency in Game: After setting online

game’s priority higher, it can lower the latency in games. Trafc

Shaping: You can watch Youtube HD videos and download

ASRock 980DE3/U3S3 Motherboard

English

9

simultaneously. Real-Time Analysis of Your Data: With the sta-

tus window, you can easily recognize which data streams you
are transferring currently.

ASRock XFast RAM

ASRock XFast RAM fully utilizes the memory space that cannot

be used under Windows® OS 32-bit CPU. ASRock XFast RAM
shortens the loading time of previously visited websites, mak-

ing web surng faster than ever. And it also boosts the speed of

Adobe Photoshop 5 times faster. Another advantage of ASRock
XFast RAM is that it reduces the frequency of accessing your
SSDs or HDDs in order to extend their lifespan.

ASRock X-Boost

ASRock’s X-Boost Technology is a smart auto-overclocking

function and is brilliantly designed to unlock the hidden power of
your CPUs. Simply press “X” when turning on the PC, X-Boost
will automatically overclock the relative components to get up to

15.77% performance boost! With the smart X-Boost, overclock­ing CPU can become a near one-button process.

* The functionality of “Unlock CPU Cores” feature might vary by

different processors.

English

10

ASRock 980DE3/U3S3 Motherboard

2. Installation

This is an ATX form factor motherboard. Before you install the motherboard, study

the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard
components or change any motherboard settings.

Before you install or remove any component, ensure that the
power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to
the motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any
component.

2. To avoid damaging the motherboard components due to static elec­tricity, NEVER place your motherboard directly on the carpet or the
like. Also remember to use a grounded wrist strap or touch a safety
grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded
anti-static pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the mother­board to the chassis, please do not over-tighten the screws! Doing
so may damage the motherboard.

ASRock 980DE3/U3S3 Motherboard

English

11

2.1 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90

o

angle.
Step 2. Position the CPU directly above the socket such that the CPU corner with
the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it ts in place.

The CPU ts only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it rmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab
to indicate that it is locked.

Lever 90° Up

CPU Golden Triangle

STEP 1:
Lift Up The Socket Lever

STEP 2 / STEP 3:
Match The CPU Golden Triangle
To The Socket Corner Small
Triangle

Socker Corner
Small Triangle

STEP 4:
Push Down And Lock
The Socket Lever

2.2 Installation of CPU Fan and Heatsink

English

12

After you install the CPU into this motherboard, it is necessary to install a
larger heatsink and cooling fan to dissipate heat. You also need to spray
thermal grease between the CPU and the heatsink to improve heat dis­sipation. Make sure that the CPU and the heatsink are securely fastened
and in good contact with each other. Then connect the CPU fan to the
CPU FAN connector (CPU_FAN1, see Page 2, No. 3). For proper instal­lation, please kindly refer to the instruction manuals of the CPU fan and
the heatsink.

ASRock 980DE3/U3S3 Motherboard

2.3 Installation of Memory Modules (DIMM)

This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots,

and supports Dual Channel Memory Technology. For dual channel conguration,

you always need to install identical (the same brand, speed, size and chip-type)
DDR3 DIMM pair in the slots. In other words, you have to install identical DDR3
DIMM pair in Dual Channel (DDR3_A1 and DDR3_B1; Black slots; see p.2 No.6)
or identical DDR3 DIMM pair in Dual Channel (DDR3_A2 and DDR3_B2; Black
slots; see p.2 No.7), so that Dual Channel Memory Technology can be activated.
This motherboard also allows you to install four DDR3 DIMMs for dual channel

conguration, and please install identical DDR3 DIMMs in all four slots. You may
refer to the Dual Channel Memory Conguration Table below.

Dual Channel Memory Congurations

DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2
(Black Slot) (Black Slot) (Black Slot) (Black Slot)
(1) Populated - Populated ­(2) - Populated - Populated
(3)* Populated Populated Populated Populated

For the conguration (3), please install identical DDR3 DIMMs in all four

*

slots.

1. Please install the memory module into the slots DDR3_A2 and

DDR3_B2 for the rst priority.

2. If you want to install two memory modules, for optimal compatibility
and reliability, it is recommended to install them either in the set of
slots DDR3_A1 and DDR3_B1, or in the set of slots DDR3_A2 and
DDR3_B2.

3. If only one memory module or three memory modules are installed
in the DDR3 DIMM slots on this motherboard, it is unable to activate
the Dual Channel Memory Technology.

4. If a pair of memory modules is NOT installed in the same Dual
Channel, for example, installing a pair of memory modules in
DDR3_A1 and DDR3_A2, it is unable to activate the Dual Channel
Memory Technology .

5. It is not allowed to install a DDR or DDR2 memory module into
DDR3 slot; otherwise, this motherboard and DIMM may be dam­aged.

6. If you adopt DDR3 1866/1600 memory modules on this mother­board, it is recommended to install them on DDR3_A2 and DDR3_
B2 slots.

English

ASRock 980DE3/U3S3 Motherboard

13

Installing a DIMM

Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.
Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the
break on the slot.

no tch
br eak

no tch

br eak

The DIMM only ts in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into
the slot at incorrect orientation.

English

14

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends
fully snap back in place and the DIMM is properly seated.

ASRock 980DE3/U3S3 Motherboard

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 2 PCI slots and 4 PCI Express slots on this motherboard.
PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.

PCIE Slots:

PCIE1 / PCIE2 / PCIE4 (PCIE x1 slot; Black) is used for PCI Express

cards with x1 lane width cards, such as Gigabit LAN card and SATA2
card.

PCIE3 (PCIE x16 slot; Black) is used for PCI Express x16 lane width

graphics cards.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed

in a chassis).
Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press rmly until the card is

completely seated on the slot.
Step 5. Fasten the card to the chassis with screws.
Step 6. Replace the system cover.

ASRock 980DE3/U3S3 Motherboard

English

15

2.5 Jumpers Setup

The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose
pin1 and pin2 are “Short” when jumper cap
is placed on these 2 pins.

Jumper Setting Description

Clear CMOS Jumper

(CLRCMOS1)
(see p.2, No. 38)

Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the
system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a
jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However,
please do not clear the CMOS right after you update the BIOS. If you need

to clear the CMOS when you just nish updating the BIOS, you must boot
up the system rst, and then shut it down before you do the clear-CMOS ac­tion. Please be noted that the password, date, time, user default prole, 1394

GUID and MAC address will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

English

16

ASRock 980DE3/U3S3 Motherboard

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!

FDD connector

(33-pin FLOPPY1)
(see p.2 No. 27)

the red-striped side to Pin1

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.

Primary IDE connector (Black)

(39-pin IDE1, see p.2 No. 36)

connect the blue end

to the motherboard

connect the black end
to the IDE devices

80-conductor ATA 66/100/133 cable

Note: Please refer to the instruction of your IDE device vendor for the details.

Serial ATA2 Connectors These six Serial ATA2 (SATA2)

(SATAII_1 (PORT 0): see p.2, No. 20)

(SATAII_2 (PORT 1): see p.2, No. 19)

(SATAII_3 (PORT 2): see p.2, No. 18)

(SATAII_4 (PORT 3): see p.2, No. 17)

(SATAII_5 (PORT 4): see p.2, No. 16)

(SATAII_6 (PORT 5): see p.2, No. 15)

connectors support SATA data
cables for internal storage
devices. The current SATA2
interface allows up to 3.0 Gb/s

data transfer rate.

SATAII_2 SATAII_4
(PORT 1) (PORT 3)

SATAII_1 SATAII_3
(PORT 0) (PORT 2)

Serial ATA3 Connectors These two Serial ATA3

(SATA3_1 (PORT 6): see p.2, No. 11)

(SATA3_2 (PORT 7): see p.2, No. 9)

(SATA3) connectors support

SATA data cables for internal

SATAII_6
(PORT 5)

SATAII_5
(PORT 4)

SATA3_2
(PORT 7)

storage devices. The current
SATA3 interface allows up to

6.0 Gb/s data transfer rate.

SATA3_1
(PORT 6)

English

ASRock 980DE3/U3S3 Motherboard

17

Serial ATA (SATA) Either end of the SATA data

CD- L

GND

GND

CD- R

Data Cable cable can be connected to the

(Optional)

SATA / SATA2 / SATA3 hard
disk or the SATA3 connector on
this motherboard.

USB 2.0 Headers Besides four default USB 2.0

(9-pin USB4_5)

(see p.2 No. 22)

ports on the I/O panel, there

are three USB 2.0 headers on
this motherboard. Each USB 2.0
header can support two USB

2.0 ports.

(9-pin USB6_7)
(see p.2 No. 21)

English

1

USB _PWR

P-9

P-8

USB _PWR

P+9

P+8

GND

GND

DUM MY

(9-pin USB8_9)
(see p.2 No. 23)

Infrared Module Header This header supports an

(5-pin IR1)

optional wireless transmitting

(see p.2 No. 31)

and receiving infrared module.

Internal Audio Connectors This connector allows you to

(4-pin CD1)

(CD1: see p.2 No. 28)

receive stereo audio input from

CD1

sound sources such as a
CD-ROM, DVD-ROM, TV tuner
card, or MPEG card.

Front Panel Audio Header This is an interface for the front

(9-pin HD_AUDIO1)

(see p.2 No. 29)

panel audio cable that allows

convenient connection and

control of audio devices.

1

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

18

ASRock 980DE3/U3S3 Motherboard

1. High Denition Audio supports Jack Sensing, but the panel wire on

the chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio
header as below:

A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

E. To activate the front mic.
For Windows® XP / XP 64-bit OS:
Select “Mixer”. Select “Recorder”. Then click “FrontMic”.
For Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:
Go to the "FrontMic" Tab in the Realtek Control panel. Adjust

“Recording Volume”.

System Panel Header This header accommodates

(9-pin PANEL1)

(see p.2 No. 24)

several system front panel

functions.

Connect the power switch, reset switch and system status indicator
on the chassis to this header according to the pin assignments below.
Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may con-

gure the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset
switch to restart the computer if the computer freezes and fails to per­form a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The
LED is on when the system is operating. The LED keeps blinking
when the sys-tem is in S1 sleep state. The LED is off when the system
is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The
LED is on when the hard drive is reading or writing data.

ASRock 980DE3/U3S3 Motherboard

English

19

The front panel design may differ by chassis. A front panel module
mainly consists of power switch, reset switch, power LED, hard drive
activity LED, speaker and etc. When connecting your chassis front
panel module to this header, make sure the wire assignments and the
pin assign-ments are matched correctly.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1)

(see p.2 No. 26)

speaker to this header.

Power LED Header Please connect the chassis

(3-pin PLED1)

(see p.2 No. 25)

power LED to this header to

indicate system power status.
The LED is on when the system
is operating. The LED keeps
blinking in S1 state. The LED is
off in S3/S4 state or S5 state
(power off).

Chassis and Power Fan Connectors Please connect the fan cables

(4-pin CHA_FAN1)

(see p.2 No. 12)

to the fan connectors and

match the black wire to the
ground pin.

(4-pin PWR_FAN1)
(see p.2 No. 2)

English

20

CPU Fan Connectors Please connect the CPU fan

(4-pin CPU_FAN1)

(see p.2 No. 3)

cable to the connector and

match the black wire to the

ground pin.

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin

CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this
motherboard, please connect it to Pin 1-3.

Pin 1-3 Connected

3-Pin Fan Installation

ASRock 980DE3/U3S3 Motherboard

ATX Power Connector Please connect an ATX power

(24-pin ATXPWR1)

(see p.2 No. 10)

Though this motherboard provides 24-pin ATX power connector,
it can still work if you adopt a traditional 20-pin ATX power supply.

supply to this connector.

12

24

1

13

12

To use the 20-pin ATX power supply, please plug your power
supply along with Pin 1 and Pin 13.

24

20-Pin ATX Power Supply Installation

ATX 12V Power Connector Please connect an ATX 12V

(8-pin ATX12V1)

(see p.2 No. 1)

power supply to this connector.

5 1

8 4

1

13

Though this motherboard provides 8-pin ATX 12V power connector, it can still work
if you adopt a traditional 4-pin ATX 12V power supply. To use the

5 1

4-pin ATX power supply, please plug your power supply along with
Pin 1 and Pin 5.

4-Pin ATX 12V Power Supply Installation

8 4

HDMI_SPDIF Header HDMI_SPDIF header, providing

(2-pin HDMI_SPDIF1)

see p.2 No. 30)

(

VGA card, allows the system to

SPDIF audio output to HDMI

1

SPD I FOUT

GND

connect HDMI Digital TV/
projector/LCD devices. Please
connect the HDMI_SPDIF
connector of HDMI VGA card to
this header.

USB 3.0 Header Besides two default USB 3.0

(19-pin USB3_2_3)

(see p.2 No. 39)

ports on the I/O panel, there is

one USB 3.0 header on this
motherboard. This USB 3.0
header can support two USB 3.0
ports.

English

ASRock 980DE3/U3S3 Motherboard

21

2.7 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical

drive rst. Then, the drivers compatible to your system can be auto-detected and

listed on the support CD driver page. Please follow the order from up to bottom side
to install those required drivers. Therefore, the drivers you install can work properly.

2.8 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista

TM

/

VistaTM 64-bit / XP / XP 64-bit With RAID Functions

If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP
/ XP 64-bit on your SATA / SATA2 HDDs with RAID functions, please refer to the
document at the following path in the Support CD for detailed procedures:

..\ RAID Installation Guide

2.9 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /
VistaTM 64-bit / XP / XP 64-bit Without RAID Functions

If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP
/ XP 64-bit OS on your SATA / SATA2 / SATA3 HDDs without RAID functions, please
follow below procedures according to the OS you install.

2.9.1 Installing Windows® XP / XP 64-bit Without RAID
Functions

If you want to install Windows® XP / XP 64-bit on your SATA / SATA2 / SATA3 HDDs
without RAID functions, please follow below steps.

Using SATA / SATA2 / SATA3 HDDs without NCQ and Hot Plug functions (IDE
mode)

English

22

STEP 1: Set up BIOS.

A. Enter BIOS SETUP UTILITY Advanced screen Storage Conguration.

B. Set the “SATA Operation Mode” option to [IDE] for SATA2 ports.
Set the “Onboard SATA3 Operation Mode” option to [IDE] for SATA3 ports.

STEP 2: Install Windows® XP / XP 64-bit OS on your system.

ASRock 980DE3/U3S3 Motherboard

2.9.2 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /
VistaTM 64-bit Without RAID Functions

If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit on
your SATA / SATA2 / SATA3 HDDs without RAID functions, please follow below
steps.

Using SATA / SATA2 / SATA3 HDDs without NCQ and Hot Plug functions (IDE
mode)

STEP 1: Set up BIOS.

A. Enter BIOS SETUP UTILITY Advanced screen Storage Conguration.

B. Set the “SATA Operation Mode” option to [IDE] for SATA2 ports.
Set the “Onboard SATA3 Operation Mode” option to [IDE] for SATA3 ports.

STEP 2: Install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on

your system.

Using SATA / SATA2 / SATA3 HDDs with NCQ and Hot Plug functions (AHCI
mode)

STEP 1: Set up BIOS.

A. Enter BIOS SETUP UTILITY Advanced screen Storage Conguration.

B. Set the “SATA Operation Mode” option to [AHCI] for SATA2 ports.
Set the “Onboard SATA3 Operation Mode” option to [AHCI] for SATA3 ports.

STEP 2: Install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on

your system.

2.10 Untied Overclocking Technology

This motherboard supports Untied Overclocking Technology, which means during

overclocking, FSB enjoys better margin due to xed PCI / PCIE buses. Before you

enable Untied Overclocking function, please enter “Overclock Mode” option of BIOS
setup to set the selection from [Auto] to [Manual]. Therefore, CPU FSB is untied
during overclocking, but PCI / PCIE buses are in the xed mode so that FSB can

operate under a more stable overclocking environment.

Please refer to the warning on page 7 for the possible overclocking risk
before you apply Untied Overclocking Technology.

ASRock 980DE3/U3S3 Motherboard

English

23

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up
the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST)
to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you
wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl>
+ <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS
Setup program is designed to be user-friendly. It is a menu-driven program, which
allows you to scroll through its various sub-menus and to select among the prede­termined choices. For the detailed information about BIOS Setup, please refer to the

User Manual (PDF le) contained in the Support CD.

4. Software Support CD information

®

This motherboard supports various Microsoft
64-bit / 7 / 7 64-bit / VistaTM / Vista
Support CD that came with the motherboard contains necessary drivers and use­ful utilities that will enhance motherboard features. To begin using the Support CD,
insert the CD into your CD-ROM drive. It will display the Main Menu automatically if
“AUTORUN” is enabled in your computer. If the Main Menu does not appear auto-

matically, locate and double-click on the le “ASSETUP.EXE” from the BIN folder in

the Support CD to display the menus.

TM

64-bit / XP / XP Media Center / XP 64-bit. The

Windows® operating systems: 8 / 8

English

24

ASRock 980DE3/U3S3 Motherboard

1. Einführung

Wir danken Ihnen für den Kauf des ASRock 980DE3/U3S3 Motherboard, ein zuver-

lässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von

ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design,
gemäß der Verpflichtung von ASRock zu Qualität und Halbarkeit. Diese Schnel­linstallationsanleitung führt in das Motherboard und die schrittweise Installation

ein. Details über das Motherboard nden Sie in der Bedienungsanleitung auf der

Support-CD.

Da sich Motherboard-Spezikationen und BIOS-Software verändern

können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert
werden. Für den Fall, dass sich Änderungen an diesem Handbuch
ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere

Ankündigung, verfügbar sein. Die neuesten Grakkarten und unterstützten

CPUs sind auch auf der ASRock-Website aufgelistet.
ASRock-Website: http://www.asrock.com
Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezische
Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere
Webseite:
www.asrock.com/support/index.asp

1.1 Kartoninhalt

ASRock 980DE3/U3S3 Motherboard (ATX-Formfaktor)
ASRock 980DE3/U3S3 Schnellinstallationsanleitung
ASRock 980DE3/U3S3 Support-CD
Zwei Serial ATA (SATA) -Datenkabel (optional)
Ein I/O Shield

ASRock erinnert...

Zur besseren Leistung unter Windows® 8 / 8 64 Bit / 7 / 7 64 Bit / Vista
VistaTM 64 Bit empfehlen wir, die Speicherkonguration im BIOS auf den

AHCI-Modus einzustellen. Hinweise zu den BIOS-Einstellungen nden

Sie in der Bedienungsanleitung auf der mitgelieferten CD.

TM

ASRock 980DE3/U3S3 Motherboard

/

Deutsch

25

Deutsch

1.2 Spezikationen

Plattform - ATX-Formfaktor

- Alle Feste Kondensatordesign
CPU - Unterstützung von Socket AM3+-Prozessoren

- Unterstützung von Socket AM3-Prozessoren: AMD
PhenomTM II X6 / X4 / X3 / X2 (außer 920 / 940) / Athlon X4 /
X3 / X2 / Sempron-Prozessor

- Acht-Kern-CPU-bereit

- Digi Power-Design

- Unterstützt CPU bis 140W

- Unterstützt AMD OverDriveTM mit ACC-Funktion (Advanced
Clock Calibration, Erweiterte Taktkalibrierung)

- Unterstützt Cool ‘n’ QuietTM-Technologie von AMD

- FSB 2600 MHz (5.2 GT/s)

- Unterstützt Untied-Übertaktungstechnologie

- Unterstützt Hyper-Transport- 3.0 Technologie (HT 3.0)
Chipsatz - Northbridge: AMD RX881/760G

- Southbridge: AMD SB710
Speicher - Unterstützung von Dual-Kanal-Speichertechnologie

- 4 x Steckplätze für DDR3

- Unterstützt DDR3 1866(OC)/1600(OC)/1333/1066/800
non-ECC, ungepufferter Speicher

- Max. Kapazität des Systemspeichers: 32GB
Erweiterungs- - 1 x PCI-Express-2.0-x16-Steckplätze (PCIE3: x16-Modus)
Steckplätze - 3 x PCI Express 2.0 x1-Steckplätze

- 2 x PCI -Steckplätze

Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec)
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Unterstützt Wake-On-LAN

- Unterstützt LAN-Kabelerkennung

- Unterstützt energieefzientes Ethernet 802.3az

- Unterstützt PXE
E/A-Anschlüsse I/O Panel
an der - 1 x PS/2-Mausanschluss
Rückseite - 1 x PS/2-Tastaturanschluss

- 1 x Serieller port: COM 1

- 4 x Standard-USB 2.0-Anschlüsse

- 2 x Standard-USB 3.0-Anschlüsse

26

ASRock 980DE3/U3S3 Motherboard

- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED
LED)

- HD Audiobuchse: Audioeingang / Lautsprecher vorne /
Mikrofon
SATA3 - 2 x SATA 3-Anschlüsse (6,0 Gb/s) durch ASMedia

ASM1061; unterstützt NCQ-, AHCI-und „Hot Plug“ (Hot-

Plugging)-Funktionen
USB3.0 - 2 x USB 3.0-Ports an der Rückseite durch Etron EJ188,
unterstützt USB 1.1/2.0/3.0 mit bis zu 5 Gb/s

- 1 x USB 3.0-Header (unterstützt zwei USB 3.0-Ports) an der
Vorderseite durch Etron EJ188, unterstützt USB 1.1/2.0/3.0
mit bis zu 5 Gb/s
Anschlüsse - 6 x SATA2 3,0 GB/s-Anschlüsse, unterstützen RAID- (RAID

0, RAID 1, RAID 10 und JBOD), NCQ-, AHCI-und Hot Plug

Funktionen

- 2 x SATA3 6,0 GB/s-Anschlüsse

- 1 x ATA133 IDE-Anschlüsse (Unterstützt bis 2 IDE-Geräte)

- 1 x FDD-Anschlüsse

- 1 x Infrarot-Modul-Header

- 1 x HDMI_SPDIF-Anschluss

- 1 x Betriebs-LED-Header

- 1 x CPUlüfter-Anschluss (4-pin)

- 1 x Gehäuselüfter-Anschluss (4-pin)

- 1 x Stromlüfter-Anschluss (4-pin)

- 24-pin ATX-Netz-Header

- 8-pin anschluss für 12V-ATX-Netzteil

- Interne Audio-Anschlüsse

- Anschluss für Audio auf der Gehäusevorderseite

- 3 x USB 2.0-Anschlüsse (Unterstützung 6 zusätzlicher
USB 2.0-Anschlüsse)

- 1 x USB 3.0-Anschlüsse (Unterstützung 2 zusätzlicher
USB 3.0-Anschlüsse)
BIOS - 16Mb AMIs Legal BIOS

- Unterstützung für “Plug and Play”

- ACPI 1.1-Weckfunktionen

- JumperFree-Modus

- SMBIOS 2.3.1

- CPU, VCCM, NB Stromspannung Multianpassung
Support-CD - Treiber, Dienstprogramme, Antivirussoftware
(Probeversion), CyberLink MediaEspresso 6.5-Testversion,
Google Chrome Browser und Toolbar

Deutsch

ASRock 980DE3/U3S3 Motherboard

27

Hardware Monitor - CPU-Temperatursensor

- Motherboardtemperaturerkennung

- Drehzahlmessung für CPU/Gehäuse/Stromlüfter

- CPU lüftergeräuschdämpfung

- Mehrstuge Geschwindigkeitsteuerung für CPU/Gehäuse/

Stromlüfter

- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore

®

Betriebssysteme - Unterstützt Microsoft
VistaTM / Vista

TM

Windows® 8 / 8 64-Bit / 7 / 7 64-Bit /

64-Bit / XP / XP Media Center / XP 64-Bit

Zertizierungen - FCC, CE, WHQL

- Gemäß Ökodesign-Richtlinie (ErP/EuP) (Stromversorgung
gemäß Ökodesign-Richtlinie (ErP/EuP) erforderlich)

* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website:
http://www.asrock.com

Deutsch

28

ASRock 980DE3/U3S3 Motherboard

1.3 Einstellung der Jumper

Die A bbildung verdeutlicht, wie Jumper
gesetzt w e r d e n . We r d e n P ins du r c h
Jumperkappen verdeckt, ist der Jumper
“gebrückt”. Werden keine Pins durch Jump­erkappen verdeckt, ist der Jumper “offen”.
Die Abbildung zeigt einen 3-Pin Jumper
dessen Pin1 und Pin2 “gebrückt” sind, bzw.
es befindet sich eine Jumper-Kappe auf
diesen beiden Pins.

Jumper Einstellun

CMOS löschen

(CLRCMOS1, 3-Pin jumper)
(siehe S.2, No. 38)

Default­Einstellung

Hinweis: CLRCMOS1 erlaubt Ihnen das Löschen der CMOS-Daten. Diese beinhal-

ten das System-Passwort, Datum, Zeit und die verschiedenen BIOS-Para­meter. Um die Systemparameter zu löschen und auf die Werkseinstellung
zurückzusetzen, schalten Sie bitte den Computer ab und entfernen das
Stromkabel. Benutzen Sie eine Jumperkappe, um die

Pin 2 und Pin 3 an CLRCMOS1 für 5 Sekunden kurzzuschließen. Bitte

vergessen Sie nicht, den Jumper wieder zu entfernen, nachdem das
CMOS gelöscht wurde. Bitte vergessen Sie nicht, den Jumper wieder zu
entfernen, nachdem das CMOS gelöscht wurde. Wenn Sie den CMOS­Inhalt gleich nach dem Aktualisieren des BIOS löschen müssen, müssen
Sie zuerst das System starten und dann wieder ausschalten, bevor Sie
den CMOS-Inhalt löschen.

CMOS
löschen

ASRock 980DE3/U3S3 Motherboard

Deutsch

29

1.4 Integrierte Header und Anschlüsse

Anschluss für das
Floppy-Laufwerk

(33-Pin FLOPPY1)
(siehe S.2 - No. 27)

Hinweis: Achten Sie darauf, dass die rotgestreifte Seite des Kabel mit der Stift 1-
Seite des Anschlusses verbunden wird.

Primärer IDE-Anschluss (schwarz)

(39-pin IDE1, siehe S.2 - No. 36)

Blauer Anschluss Schwarzer Anschluss
zum Motherboard zur Festplatte
80-adriges ATA 66/100/133 Kabel

Hinweis: Details entnehmen Sie bitte den Anweisungen Ihres IDE-Gerätehändlers.

Integrierte Header und Anschlüsse sind KEINE Jumper. Setzen Sie KE­INE Jumperkappen auf diese Header und Anschlüsse. Wenn Sie Jump­erkappen auf Header und Anschlüsse setzen, wird das Motherboard
unreparierbar beschädigt!

die rotgestreifte Seite auf Stift 1

Deutsch

30

Seriell-ATAII-Anschlüsse Diese sechs Serial ATAII-

(SATAII_1 (PORT 0): siehe S.2 - No. 20)

(SATAII_2 (PORT 1): siehe S.2 - No. 19)

(SATAII_3 (PORT 2): siehe S.2 - No. 18)

(SATAII_4 (PORT 3): siehe S.2 - No. 17)

(SATAII_5 (PORT 4): siehe S.2 - No. 16)

(SATAII_6 (PORT 5): siehe S.2 - No. 15)

Datenübertragungsrate bis

(SATAII-)Verbínder
unterstützten SATA-Datenkabel
für interne
Massenspeichergeräte. Die
aktuelle SATAII-Schnittstelle
ermöglicht eine

SATAII_2 SATAII_4
(PORT 1) (PORT 3)

SATAII_6
(PORT 5)

SATAII_5
(PORT 4)

3,0 Gb/s.

SATAII_1 SATAII_3
(PORT 0) (PORT 2)

ASRock 980DE3/U3S3 Motherboard