Asrock 980DE3/U3S3 R2.0 Quick Installation Guide

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans­lated in any language, in any form or by any means, except duplication of documentation
by the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identica­tion or explanation and to the owners’ benet, without intent to infringe.

Disclaimer:

Specications and information contained in this guide are furnished for informational use

only and subject to change without notice, and should not be constructed as a commit­ment by ASRock. ASRock assumes no responsibility for any errors or omissions that may
appear in this guide.
With respect to the contents of this guide, ASRock does not provide warranty of any kind,
either expressed or implied, including but not limited to the implied warranties or condi-

tions of merchantability or tness for a particular purpose. In no event shall ASRock, its
directors, ofcers, employees, or agents be liable for any indirect, special, incidental, or
consequential damages (including damages for loss of prots, loss of business, loss of

data, interruption of business and the like), even if ASRock has been advised of the pos­sibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published September 2014

Copyright©2014 ASRock INC. All rights reserved.

ASRock 980DE3/U3S3 R2.0 Motherboard

English

1

Motherboard Layout

AMD

SB7 10

Chi pset

ATX12V1

8Mb

BIOS

CMOS

BATTER Y

CLRCMOS1

1

LAN
PHY

AUDIO
CODEC

Super

I/O

IR1

1

CD1

HD_AUDIO1

1

PCIE 1

FLOPPY1

HDLED RESET

PLEDPW RBTN

1

PANEL1

SPEAKER1

1

SATAII_2(PORT 1)

AMD

770

Chi pse t

PCI1

PCI2

980 DE3 /U3 S3

SATAII_4(PORT 3)

SATAII_3(PORT 2)

Top:

LINE IN

Center:

FRONT

Bottom:

MIC IN

PS2

Mouse

PS2

Keybo ard

USB 2.0
T:US B0
B: USB1

Top:
RJ-45

USB 3.0
T:US B0
B: USB1

Fron t USB 3. 0

ErP/ EuP Re ady

RoHS

USB8_9

1

SATAII_1(PORT 0)

SATAII_6(PORT 5)

SATAII_5(PORT 4)

1

PLED1

1

HDMI_SPDIF1

USB6_7

1

USB4_5

1

USB 2.0
T:US B2
B: USB3

COM1

CHA_FAN1

Supp ort 8-C ore CPU

36

37

38

SO CKE T A M3b

PCIE 2

PCIE 4

PCIE 3

FSB 800

DDR3_ A1( 64 bit, 240-p inm odule)

DDR3_ A2( 64 bit, 240-p inm odule)

FSB 800

DDR3_ B1( 64 bit, 240-p inm odule)

DDR3_ B2( 64 bit, 240-p inm odule)

SATA3_2(PORT 7)

SATA3_1(PORT 6)

DDR3 1 866

AM3+
140W CP U

CPU_FAN1PWR_FAN1

X

Fast R AM

X

Fast L AN

USB3_2_3

39

English

2

5

3

1

35

4

2

IDE1

34

33

7

6

8
9

10

11

12

13

14

32

31

30

27

29

28

25

24

26

23

19

21

20

22

15
16

17
18

1 ATX 12V Power Connector (ATX12V1) 20 SATA2 Connector (SATA2_1 (PORT 1))
2 Power Fan Connector (PWR_FAN1) 21 USB 2.0 Header (USB6_7)
3 CPU Fan Connector (CPU_FAN1) 22 USB 2.0 Header (USB4_5)
4 AM3+ CPU Socket 23 USB 2.0 Header (USB8_9)
5 CPU Heatsink Retention Module 24 System Panel Header (PANEL1)
6 2 x 240-pin DDR3 DIMM Slots 25 Power LED Header (PLED1)
(Dual Channel: DDR3_A1, DDR3_B1) 26 Chassis Speaker Header (SPEAKER1)
7 2 x 240-pin DDR3 DIMM Slots 27 Floppy Connector (FLOPPY1)
(Dual Channel: DDR3_A2, DDR3_B2) 28 Internal Audio Connector (CD1)
8 Northbridge Controller 29 Front Panel Audio Header (HD_AUDIO1)
9 SATA3 Connector (SATA3_2 (PORT 7)) 30 HDMI_SPDIF Header (HDMI_SPDIF1)
10 ATX Power Connector (ATXPWR1) 31 Infrared Module Header (IR1)
11 SATA3 Connector (SATA3_1 (PORT 6)) 32 PCI Slots (PCI1-2)
12 Chassis Fan Connector (CHA_FAN1) 33 PCI Express 2.0 x1 Slot (PCIE4)
13 Southbridge Controller 34 PCI Express 2.0 x16 Slot (PCIE3)
14 SPI Flash Memory (16Mb) 35 PCI Express 2.0 x1 Slot (PCIE2)
15 SATA2 Connector (SATA2_6 (PORT 5)) 36 IDE1 Connector (IDE1)
16 SATA2 Connector (SATA2_5 (PORT 4)) 37 PCI Express 2.0 x1 Slot (PCIE1)
17 SATA2 Connector (SATA2_4 (PORT 3)) 38 Clear CMOS Jumper (CLRCMOS1)
18 SATA2 Connector (SATA2_3 (PORT 2)) 39 USB 3.0 Header (USB3_2_3)
19 SATA2 Connector (SATA2_2 (PORT 1))

ASRock 980DE3/U3S3 R2.0 Motherboard

I/O Panel

1

2

3

4

5

910

1 PS/2 Mouse Port (Green) 6 USB 2.0 Ports (USB01)
* 2 LAN RJ-45 Port 7 USB 3.0 Port (USB01)
3 Line In (Light Blue) 8 USB 2.0 Ports (USB23)
** 4 Front Speaker (Lime) 9 Serial Port: COM1
5 Microphone (Pink) 10 PS/2 Keyboard Port (Purple)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED
indications.

Activity/Link LED SPEED LED

Status Description Status Description

LAN Port LED Indications

8

7

6

ACT/LINK
LED

SPEED
LED

Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

LAN Port

** To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. Please refer to below steps for the software setting of Multi-Streaming.
For Windows® XP:

After restarting your computer, you will nd “Mixer” tool on your system. Please select “Mixer

ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or

“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker
and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then
reboot your system.
For Windows® 8.1 / 8 / 7 / VistaTM:
After restarting your computer, please double-click “Realtek HD Audio Manager” on the

system tray. Set “Speaker Conguration” to “Quadraphonic” or “Stereo”. Click “Device

advanced settings”, choose “Make front and rear output devices playbacks two different audio
streams simultaneously”, and click “ok”. Then reboot your system.

ASRock 980DE3/U3S3 R2.0 Motherboard

English

3

1. Introduction

Thank you for purchasing ASRock 980DE3/U3S3 R2.0 motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control. It
delivers excellent performance with robust design conforming to ASRock’s commit­ment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found
in the user manual presented in the Support CD.

Because the motherboard specications and the BIOS software might

be updated, the content of this manual will be subject to change without
notice. In case any modications of this manual occur, the updated ver­sion will be available on ASRock website without further notice. You may

nd the latest VGA cards and CPU support lists on ASRock website as

well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for specic information about the model you are using.

www.asrock.com/support/index.asp

1.1 Package Contents

ASRock 980DE3/U3S3 R2.0 Motherboard (ATX Form Factor)
ASRock 980DE3/U3S3 R2.0 Quick Installation Guide
ASRock 980DE3/U3S3 R2.0 Support CD
2 x Serial ATA (SATA) Data Cables (Optional)
1 x I/O Panel Shield

English

4

ASRock 980DE3/U3S3 R2.0 Motherboard

1.2 Specications

Platform - ATX Form Factor

- All Solid Capacitor design

- High Density Glass Fabric PCB
CPU - Support for Socket AM3+ Processors

- Support for Socket AM3 Processors: AMD PhenomTM II X6 /
X4 / X3 / X2 (except 920 / 940) / Athlon II X4 / X3 / X2 /
Sempron Processors

- Supports 8-Core CPU

- Digi Power design

- Supports CPU up to 140W

- Supports AMD OverDrive™ with ACC feature (Advanced
Clock Calibration)

- Supports AMD’s Cool ‘n’ Quiet Technology

- FSB 2600 MHz (5.2 GT/s)

- Supports Untied Overclocking Technology

- Supports Hyper-Transport 3.0 (HT 3.0) Technology
Chipset - Northbridge: AMD 770

- Southbridge: AMD SB710
Memory - Dual Channel DDR3 Memory Technology

- 4 x DDR3 DIMM Slots

- Supports DDR3 1866(OC)/1600(OC)/1333/1066/800
non-ECC, un-buffered memory (see CAUTION 1)

- Max. capacity of system memory: 32GB (see CAUTION 2)
Expansion Slot - 1 x PCI Express 2.0 x16 Slot (PCIE3 @ x16 mode)

- 3 x PCI Express 2.0 x1 Slots

- 2 x PCI Slots
Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec)

- Supports Surge Protection (ASRock Full Spike Protection)
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supports Wake-On-LAN

- Supports Lightning/ESD Protection (ASRock Full Spike
Protection)

- Supports LAN Cable Detection

- Supports Energy Efcient Ethernet 802.3az

- Supports PXE
Rear Panel I/O - 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Serial Port: COM1

English

ASRock 980DE3/U3S3 R2.0 Motherboard

5

English

- 4 x USB 2.0 Ports

- 2 x USB 3.0 Ports (Etron EJ188)

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)

- HD Audio Jacks: Line in / Front Speaker / Microphone
Storage - 6 x SATA2 3.0 Gb/s Connectors, support RAID (RAID 0,

RAID 1, RAID 10 and JBOD), NCQ, AHCI and Hot Plug

- 2 x SATA3 6.0 Gb/s Connectors by ASMedia ASM1061,

support NCQ, AHCI and Hot Plug

Connector - 1 x ATA133 IDE Connector (Supports 2 x IDE Devices)

- 1 x Floppy Connector

- 1 x IR Header

- 1 x HDMI_SPDIF Header

- 1 x Power LED Header

- 1 x CPU Fan Connector (4-pin)

- 1 x Chassis Fan Connector (4-pin)

- 1 x Power Fan Connector (4-pin)

- 1 x 24 pin ATX Power Connector

- 1 x 8 pin 12V Power Connector

- 1 x CD In Header

- 1 x Front Panel Audio Connector

- 3 x USB 2.0 Headers (Support 6 USB 2.0 ports)

- 1 x USB 3.0 Header (Etron EJ188) (Supports 2 USB 3.0
ports)
BIOS Feature - 8Mb AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliant wake up events

- Supports jumperfree

- SMBIOS 2.3.1 Support

- CPU, VCCM, NB Voltage Multi-adjustment
Hardware - CPU temperature sensing
Monitor - Chassis temperature sensing

- CPU/Chassis/Power Fan Tachometer

- CPU Quiet Fan (Auto adjust chassis fan speed by CPU

temperature)

- CPU/Chassis/Power Fan multi-speed control

- Voltage monitoring: +12V, +5V, +3.3V, Vcore
OS - Microsoft® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit /
8 64-bit / 7 32-bit / 7 64-bit / VistaTM 32-bit / VistaTM 64-bit /
XP 32-bit / XP 64-bit

6

ASRock 980DE3/U3S3 R2.0 Motherboard

Certications - FCC, CE, WHQL

- ErP/EuP ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with overclocking,
including adjusting the setting in the BIOS, applying Untied Overclocking
Technology, or using third-party overclocking tools. Overclocking may
affect your system’s stability, or even cause damage to the components
and devices of your system. It should be done at your own risk and
expense. We are not responsible for possible damage caused by
overclocking.

CAUTION!

1. Whether 1866/1600MHz memory speed is supported depends
on the AM3/AM3+ CPU you adopt. If you want to adopt DDR3
1866/1600 memory module on this motherboard, please refer
to the memory support list on our website for the compatible
memory modules.

ASRock website: http://www.asrock.com

2. Due to the operating system limitation, the actual memory size
may be less than 4GB for the reservation for system usage un­der Windows® 8.1 / 8 / 7 / VistaTM / XP. For Windows® 64-bit OS
with 64-bit CPU, there is no such limitation.

ASRock 980DE3/U3S3 R2.0 Motherboard

English

7

2. Installation

This is an ATX form factor motherboard. Before you install the motherboard, study

the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard
components or change any motherboard settings.

Before you install or remove any component, ensure that the
power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to
the motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any
component.

2. To avoid damaging the motherboard components due to static elec­tricity, NEVER place your motherboard directly on the carpet or the
like. Also remember to use a grounded wrist strap or touch a safety
grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded
anti-static pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the mother­board to the chassis, please do not over-tighten the screws! Doing
so may damage the motherboard.

English

8

ASRock 980DE3/U3S3 R2.0 Motherboard

2.1 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90

o

angle.
Step 2. Position the CPU directly above the socket such that the CPU corner with
the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it ts in place.

The CPU ts only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it rmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab
to indicate that it is locked.

Lever 90° Up

CPU Golden Triangle

STEP 1:
Lift Up The Socket Lever

STEP 2 / STEP 3:
Match The CPU Golden Triangle
To The Socket Corner Small
Triangle

Socker Corner
Small Triangle

STEP 4:
Push Down And Lock
The Socket Lever

2.2 Installation of CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install a
larger heatsink and cooling fan to dissipate heat. You also need to spray
thermal grease between the CPU and the heatsink to improve heat dis­sipation. Make sure that the CPU and the heatsink are securely fastened
and in good contact with each other. Then connect the CPU fan to the
CPU FAN connector (CPU_FAN1, see Page 2, No. 3). For proper instal­lation, please kindly refer to the instruction manuals of the CPU fan and
the heatsink.

ASRock 980DE3/U3S3 R2.0 Motherboard

English

9

English

2.3 Installation of Memory Modules (DIMM)

This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots,

and supports Dual Channel Memory Technology. For dual channel conguration,

you always need to install identical (the same brand, speed, size and chip-type)
DDR3 DIMM pair in the slots. In other words, you have to install identical DDR3
DIMM pair in Dual Channel (DDR3_A1 and DDR3_B1; Black slots; see p.2 No.6)
or identical DDR3 DIMM pair in Dual Channel (DDR3_A2 and DDR3_B2; Black
slots; see p.2 No.7), so that Dual Channel Memory Technology can be activated.
This motherboard also allows you to install four DDR3 DIMMs for dual channel

conguration, and please install identical DDR3 DIMMs in all four slots. You may
refer to the Dual Channel Memory Conguration Table below.

Dual Channel Memory Congurations

DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2
(Black Slot) (Black Slot) (Black Slot) (Black Slot)
(1) Populated - Populated ­(2) - Populated - Populated
(3)* Populated Populated Populated Populated

For the conguration (3), please install identical DDR3 DIMMs in all four

*

slots.

1. Please install the memory module into the slots DDR3_A2 and

DDR3_B2 for the rst priority.

2. If you want to install two memory modules, for optimal compatibility
and reliability, it is recommended to install them either in the set of
slots DDR3_A1 and DDR3_B1, or in the set of slots DDR3_A2 and
DDR3_B2.

3. If only one memory module or three memory modules are installed
in the DDR3 DIMM slots on this motherboard, it is unable to activate
the Dual Channel Memory Technology.

4. If a pair of memory modules is NOT installed in the same Dual
Channel, for example, installing a pair of memory modules in
DDR3_A1 and DDR3_A2, it is unable to activate the Dual Channel
Memory Technology .

5. It is not allowed to install a DDR or DDR2 memory module into
DDR3 slot; otherwise, this motherboard and DIMM may be dam­aged.

6. If you adopt DDR3 1866/1600 memory modules on this mother­board, it is recommended to install them on DDR3_A2 and DDR3_
B2 slots.

10

ASRock 980DE3/U3S3 R2.0 Motherboard

Installing a DIMM

Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.
Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the
break on the slot.

notch
break

notch

break

The DIMM only ts in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into
the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends
fully snap back in place and the DIMM is properly seated.

ASRock 980DE3/U3S3 R2.0 Motherboard

English

11

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 2 PCI slots and 4 PCI Express slots on this motherboard.
PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.

PCIE Slots:

PCIE1 / PCIE2 / PCIE4 (PCIE x1 slot; Black) is used for PCI Express

cards with x1 lane width cards, such as Gigabit LAN card and SATA2
card.

PCIE3 (PCIE x16 slot; Black) is used for PCI Express x16 lane width

graphics cards.

English

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed

in a chassis).
Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press rmly until the card is

completely seated on the slot.
Step 5. Fasten the card to the chassis with screws.
Step 6. Replace the system cover.

12

ASRock 980DE3/U3S3 R2.0 Motherboard

2.5 Jumpers Setup

The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose
pin1 and pin2 are “Short” when jumper cap
is placed on these 2 pins.

Jumper Setting Description

Clear CMOS Jumper

(CLRCMOS1)
(see p.2, No. 38)

Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the
system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a
jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However,
please do not clear the CMOS right after you update the BIOS. If you need

to clear the CMOS when you just nish updating the BIOS, you must boot
up the system rst, and then shut it down before you do the clear-CMOS ac­tion. Please be noted that the password, date, time, user default prole, 1394

GUID and MAC address will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

ASRock 980DE3/U3S3 R2.0 Motherboard

English

13

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!

FDD connector

(33-pin FLOPPY1)
(see p.2 No. 27)

the red-striped side to Pin1

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.

Primary IDE connector (Black)

(39-pin IDE1, see p.2 No. 36)

English

connect the blue end

to the motherboard

connect the black end
to the IDE devices

80-conductor ATA 66/100/133 cable

Note: Please refer to the instruction of your IDE device vendor for the details.

Serial ATA2 Connectors These six Serial ATA2 (SATA2)

(SATAII_1 (PORT 0): see p.2, No. 20)

(SATAII_2 (PORT 1): see p.2, No. 19)

(SATAII_3 (PORT 2): see p.2, No. 18)

(SATAII_4 (PORT 3): see p.2, No. 17)

(SATAII_5 (PORT 4): see p.2, No. 16)

(SATAII_6 (PORT 5): see p.2, No. 15)

connectors support SATA data
cables for internal storage
devices. The current SATA2
interface allows up to 3.0 Gb/s

data transfer rate.

SATAII_2 SATAII_4
(PORT 1) (PORT 3)

SATAII_1 SATAII_3
(PORT 0) (PORT 2)

Serial ATA3 Connectors These two Serial ATA3

(SATA3_1 (PORT 6): see p.2, No. 11)

(SATA3_2 (PORT 7): see p.2, No. 9)

(SATA3) connectors support

SATA data cables for internal

SATAII_6
(PORT 5)

SATAII_5
(PORT 4)

SATA3_2
(PORT 7)

storage devices. The current
SATA3 interface allows up to

6.0 Gb/s data transfer rate.

SATA3_1
(PORT 6)

14

ASRock 980DE3/U3S3 R2.0 Motherboard

P-7

P+7

GND

DUM MY

USB _PWR

USB _PWR

P-6

P+6

GND

1

Serial ATA (SATA) Either end of the SATA data

CD- L

GND

GND

CD- R

Data Cable cable can be connected to the

(Optional)

SATA / SATA2 / SATA3 hard
disk or the SATA3 connector on
this motherboard.

USB 2.0 Headers Besides four default USB 2.0

(9-pin USB4_5)

(see p.2 No. 22)

ports on the I/O panel, there

are three USB 2.0 headers on
this motherboard. Each USB 2.0
header can support two USB

2.0 ports.

(9-pin USB6_7)
(see p.2 No. 21)

1

USB _PWR

P-9

P-8

USB _PWR

P+9

P+8

GND

GND

DUM MY

(9-pin USB8_9)
(see p.2 No. 23)

Infrared Module Header This header supports an

(5-pin IR1)

optional wireless transmitting

(see p.2 No. 31)

and receiving infrared module.

Internal Audio Connectors This connector allows you to

(4-pin CD1)

(CD1: see p.2 No. 28)

receive stereo audio input from

CD1

sound sources such as a
CD-ROM, DVD-ROM, TV tuner
card, or MPEG card.

Front Panel Audio Header This is an interface for the front

(9-pin HD_AUDIO1)

(see p.2 No. 29)

panel audio cable that allows

convenient connection and

control of audio devices.

ASRock 980DE3/U3S3 R2.0 Motherboard

1

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

English

15

1. High Denition Audio supports Jack Sensing, but the panel wire on

GND

RESE T#

PWRB TN#

PLED -

PLED +

GND

HDLE D-

HDLE D+

1

GND

the chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio
header as below:

A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

E. To activate the front mic.
For Windows® XP / XP 64-bit OS:
Select “Mixer”. Select “Recorder”. Then click “FrontMic”.
For Windows® 8.1 / 8.1 64-bit / 8 / 8 64-bit / 7 / 7 64-bit / VistaTM /

VistaTM 64-bit OS:

Go to the "FrontMic" Tab in the Realtek Control panel. Adjust

“Recording Volume”.

System Panel Header This header accommodates

(9-pin PANEL1)

(see p.2 No. 24)

several system front panel

functions.

Connect the power switch, reset switch and system status indicator
on the chassis to this header according to the pin assignments below.
Note the positive and negative pins before connecting the cables.

English

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may con-

gure the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset
switch to restart the computer if the computer freezes and fails to per­form a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The
LED is on when the system is operating. The LED keeps blinking
when the sys-tem is in S1 sleep state. The LED is off when the system
is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The
LED is on when the hard drive is reading or writing data.

16

ASRock 980DE3/U3S3 R2.0 Motherboard

The front panel design may differ by chassis. A front panel module

1

+5V

DUM MY

DUM MY

SPE AKE R

mainly consists of power switch, reset switch, power LED, hard drive
activity LED, speaker and etc. When connecting your chassis front
panel module to this header, make sure the wire assignments and the
pin assign-ments are matched correctly.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1)

(see p.2 No. 26)

speaker to this header.

Power LED Header Please connect the chassis

(3-pin PLED1)

(see p.2 No. 25)

power LED to this header to

indicate system power status.

1

PLE D+

PLE D+

PLE D-

The LED is on when the system
is operating. The LED keeps
blinking in S1 state. The LED is
off in S3/S4 state or S5 state
(power off).

Chassis and Power Fan Connectors Please connect the fan cables

(4-pin CHA_FAN1)

(see p.2 No. 12)

ground pin.

(4-pin PWR_FAN1)
(see p.2 No. 2)

CPU Fan Connectors Please connect the CPU fan

(4-pin CPU_FAN1)

(see p.2 No. 3)

ground pin.

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin

to the fan connectors and

match the black wire to the

FAN _SPE ED_C ONTR OL

PWR _FAN _SPE ED

+12 V

GND

FAN_ SPEE D_CO NTRO L

cable to the connector and

match the black wire to the

CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this
motherboard, please connect it to Pin 1-3.

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Pin 1-3 Connected

3-Pin Fan Installation

English

ASRock 980DE3/U3S3 R2.0 Motherboard

17

ATX Power Connector Please connect an ATX power

(24-pin ATXPWR1)

(see p.2 No. 10)

Though this motherboard provides 24-pin ATX power connector,
it can still work if you adopt a traditional 20-pin ATX power supply.

supply to this connector.

12

24

1

13

12

To use the 20-pin ATX power supply, please plug your power
supply along with Pin 1 and Pin 13.

24

English

20-Pin ATX Power Supply Installation

ATX 12V Power Connector Please connect an ATX 12V

(8-pin ATX12V1)

(see p.2 No. 1)

power supply to this connector.

5 1

8 4

1

13

Though this motherboard provides 8-pin ATX 12V power connector, it can still work
if you adopt a traditional 4-pin ATX 12V power supply. To use the

5 1

4-pin ATX power supply, please plug your power supply along with
Pin 1 and Pin 5.

4-Pin ATX 12V Power Supply Installation

8 4

HDMI_SPDIF Header HDMI_SPDIF header, providing

(2-pin HDMI_SPDIF1)

see p.2 No. 30)

(

VGA card, allows the system to

SPDIF audio output to HDMI

1

GND

SPD I FOUT

connect HDMI Digital TV/
projector/LCD devices. Please
connect the HDMI_SPDIF
connector of HDMI VGA card to
this header.

USB 3.0 Header Besides two default USB 3.0

(19-pin USB3_2_3)

(see p.2 No. 39)

ports on the I/O panel, there is

one USB 3.0 header on this
motherboard. This USB 3.0
header can support two USB 3.0
ports.

18

ASRock 980DE3/U3S3 R2.0 Motherboard

2.7 Untied Overclocking Technology

This motherboard supports Untied Overclocking Technology, which means during

overclocking, FSB enjoys better margin due to xed PCI / PCIE buses. Before you

enable Untied Overclocking function, please enter “Overclock Mode” option of BIOS
setup to set the selection from [Auto] to [Manual]. Therefore, CPU FSB is untied
during overclocking, but PCI / PCIE buses are in the xed mode so that FSB can

operate under a more stable overclocking environment.

Please refer to the warning on page 7 for the possible overclocking risk
before you apply Untied Overclocking Technology.

ASRock 980DE3/U3S3 R2.0 Motherboard

English

19

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up
the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST)
to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you
wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl>
+ <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS
Setup program is designed to be user-friendly. It is a menu-driven program, which
allows you to scroll through its various sub-menus and to select among the prede­termined choices. For the detailed information about BIOS Setup, please refer to the

User Manual (PDF le) contained in the Support CD.

4. Software Support CD information

®

This motherboard supports various Microsoft
64-bit / 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / Vista
CD that came with the motherboard contains necessary drivers and useful utilities
that will enhance motherboard features. To begin using the Support CD, insert the
CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTO­RUN” is enabled in your computer. If the Main Menu does not appear automatically,
locate and double-click on the le “ASRSETUP.EXE” from the BIN folder in the Sup­port CD to display the menus.

Windows® operating systems: 8.1 / 8.1

TM

64-bit / XP / XP 64-bit. The Support

English

20

ASRock 980DE3/U3S3 R2.0 Motherboard

1. Einführung

Wir danken Ihnen für den Kauf des ASRock 980DE3/U3S3 R2.0 Motherboard, ein

zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen

von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes De­sign, gemäß der Verpichtung von ASRock zu Qualität und Halbarkeit. Diese Sch­nellinstallationsanleitung führt in das Motherboard und die schrittweise Installation

ein. Details über das Motherboard nden Sie in der Bedienungsanleitung auf der

Support-CD.

Da sich Motherboard-Spezikationen und BIOS-Software verändern

können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert
werden. Für den Fall, dass sich Änderungen an diesem Handbuch
ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere

Ankündigung, verfügbar sein. Die neuesten Grakkarten und unterstützten

CPUs sind auch auf der ASRock-Website aufgelistet.
ASRock-Website: http://www.asrock.com
Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezische
Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere
Webseite:
www.asrock.com/support/index.asp

1.1 Kartoninhalt

ASRock 980DE3/U3S3 R2.0 Motherboard (ATX-Formfaktor)
ASRock 980DE3/U3S3 R2.0 Schnellinstallationsanleitung
ASRock 980DE3/U3S3 R2.0 Support-CD
Zwei Serial ATA (SATA) -Datenkabel (optional)
Ein I/O Shield

ASRock 980DE3/U3S3 R2.0 Motherboard

Deutsch

21

Deutsch

1.2 Spezikationen

Plattform - ATX-Formfaktor

- Alle Feste Kondensatordesign

- PCB mit hochverdichtetem Glasfasergewebe
CPU - Unterstützung von Socket AM3+-Prozessoren

- Unterstützung von Socket AM3-Prozessoren: AMD
PhenomTM II X6 / X4 / X3 / X2 (außer 920 / 940) / Athlon X4 /
X3 / X2 / Sempron-Prozessor

- Acht-Kern-CPU-bereit

- Digi Power-Design

- Unterstützt CPU bis 140W

- Unterstützt AMD OverDriveTM mit ACC-Funktion (Advanced
Clock Calibration, Erweiterte Taktkalibrierung)

- Unterstützt Cool ‘n’ QuietTM-Technologie von AMD

- FSB 2600 MHz (5.2 GT/s)

- Unterstützt Untied-Übertaktungstechnologie

- Unterstützt Hyper-Transport- 3.0 Technologie (HT 3.0)
Chipsatz - Northbridge: AMD 770

- Southbridge: AMD SB710
Speicher - Unterstützung von Dual-Kanal-Speichertechnologie

- 4 x Steckplätze für DDR3

- Unterstützt DDR3 1866(OC)/1600(OC)/1333/1066/800
non-ECC, ungepufferter Speicher

- Max. Kapazität des Systemspeichers: 32GB
Erweiterungs- - 1 x PCI-Express-2.0-x16-Steckplätze (PCIE3: x16-Modus)
Steckplätze - 3 x PCI Express 2.0 x1-Steckplätze

- 2 x PCI -Steckplätze
Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec)

- Unterstützt Überspannungsschutz (ASRocks
Komplettschutz vor Spannungsspitzen)
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Unterstützt Wake-On-LAN

- Unterstützt Schutz vor Blitzschlag/elektrostatischer
Entladung (ASRocks Komplettschutz vor
Spannungsspitzen)

- Unterstützt LAN-Kabelerkennung

- Unterstützt energieefzientes Ethernet 802.3az

- Unterstützt PXE

22

ASRock 980DE3/U3S3 R2.0 Motherboard

E/A-Anschlüsse - 1 x PS/2-Mausanschluss
an der - 1 x PS/2-Tastaturanschluss

Rückseite - 1 x Serieller port: COM 1

- 4 x Standard-USB 2.0-Anschlüsse

- 2 x Standard-USB 3.0-Anschlüsse (Etron EJ188)

- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED
LED)

- HD Audiobuchse: Audioeingang / Lautsprecher vorne /
Mikrofon
Speicher - 6 x SATA2 3,0 GB/s-Anschlüsse, unterstützen RAID- (RAID

0, RAID 1, RAID 10 und JBOD), NCQ-, AHCI-und Hot Plug

Funktionen

- 2 x SATA 3-Anschlüsse (6,0 Gb/s) durch ASMedia

ASM1061; unterstützt NCQ-, AHCI-und „Hot Plug“ (Hot-

Plugging)-Funktionen
Anschlüsse - 1 x ATA133 IDE-Anschlüsse (Unterstützt bis 2 IDE-Geräte)

- 1 x FDD-Anschlüsse

- 1 x Infrarot-Modul-Header

- 1 x HDMI_SPDIF-Anschluss

- 1 x Betriebs-LED-Header

- 1 x CPUlüfter-Anschluss (4-pin)

- 1 x Gehäuselüfter-Anschluss (4-pin)

- 1 x Stromlüfter-Anschluss (4-pin)

- 1 x 24-pin ATX-Netz-Header

- 1 x 8-pin anschluss für 12V-ATX-Netzteil

- 1 x Interne Audio-Anschlüsse

- 1 x Anschluss für Audio auf der Gehäusevorderseite

- 3 x USB 2.0-Anschlüsse (Unterstützung 6 zusätzlicher
USB 2.0-Anschlüsse)

- 1 x USB 3.0-Anschlüsse (Etron EJ188) (Unterstützung 2
zusätzlicher USB 3.0-Anschlüsse)
BIOS - 8Mb AMIs Legal BIOS

- Unterstützung für “Plug and Play”

- ACPI 1.1-Weckfunktionen

- JumperFree-Modus

- SMBIOS 2.3.1

- CPU, VCCM, NB Stromspannung Multianpassung

Deutsch

ASRock 980DE3/U3S3 R2.0 Motherboard

23

Hardware Monitor - CPU-Temperatursensor

- Motherboardtemperaturerkennung

- Drehzahlmessung für CPU/Gehäuse/Stromlüfter

- CPU lüftergeräuschdämpfung

- Mehrstuge Geschwindigkeitsteuerung für CPU/Gehäuse/

Stromlüfter

- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore

®

Betriebssysteme - Unterstützt Microsoft
64-Bit / 7 / 7 64-Bit / VistaTM / Vista

Windows® 8.1 / 8.1 64-Bit / 8 / 8

TM

64-Bit / XP / XP 64-Bit

Zertizierungen - FCC, CE, WHQL

- Gemäß Ökodesign-Richtlinie (ErP/EuP) (Stromversorgung
gemäß Ökodesign-Richtlinie (ErP/EuP) erforderlich)

* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website:
http://www.asrock.com

Deutsch

24

ASRock 980DE3/U3S3 R2.0 Motherboard

1.3 Einstellung der Jumper

Die A bbildung verdeutlicht, wie Jumper
gesetzt w e r d e n . We r d e n P ins du r c h
Jumperkappen verdeckt, ist der Jumper
“gebrückt”. Werden keine Pins durch Jump­erkappen verdeckt, ist der Jumper “offen”.
Die Abbildung zeigt einen 3-Pin Jumper
dessen Pin1 und Pin2 “gebrückt” sind, bzw.
es befindet sich eine Jumper-Kappe auf
diesen beiden Pins.

Jumper Einstellun

CMOS löschen

(CLRCMOS1, 3-Pin jumper)
(siehe S.2, No. 38)

Default­Einstellung

Hinweis: CLRCMOS1 erlaubt Ihnen das Löschen der CMOS-Daten. Diese beinhal-

ten das System-Passwort, Datum, Zeit und die verschiedenen BIOS-Para­meter. Um die Systemparameter zu löschen und auf die Werkseinstellung
zurückzusetzen, schalten Sie bitte den Computer ab und entfernen das
Stromkabel. Benutzen Sie eine Jumperkappe, um die

Pin 2 und Pin 3 an CLRCMOS1 für 5 Sekunden kurzzuschließen. Bitte

vergessen Sie nicht, den Jumper wieder zu entfernen, nachdem das
CMOS gelöscht wurde. Bitte vergessen Sie nicht, den Jumper wieder zu
entfernen, nachdem das CMOS gelöscht wurde. Wenn Sie den CMOS­Inhalt gleich nach dem Aktualisieren des BIOS löschen müssen, müssen
Sie zuerst das System starten und dann wieder ausschalten, bevor Sie
den CMOS-Inhalt löschen.

CMOS
löschen

ASRock 980DE3/U3S3 R2.0 Motherboard

Deutsch

25

1.4 Integrierte Header und Anschlüsse

Anschluss für das
Floppy-Laufwerk

(33-Pin FLOPPY1)
(siehe S.2 - No. 27)

Hinweis: Achten Sie darauf, dass die rotgestreifte Seite des Kabel mit der Stift 1-
Seite des Anschlusses verbunden wird.

Primärer IDE-Anschluss (schwarz)

(39-pin IDE1, siehe S.2 - No. 36)

Blauer Anschluss Schwarzer Anschluss
zum Motherboard zur Festplatte
80-adriges ATA 66/100/133 Kabel

Hinweis: Details entnehmen Sie bitte den Anweisungen Ihres IDE-Gerätehändlers.

Integrierte Header und Anschlüsse sind KEINE Jumper. Setzen Sie KE­INE Jumperkappen auf diese Header und Anschlüsse. Wenn Sie Jump­erkappen auf Header und Anschlüsse setzen, wird das Motherboard
unreparierbar beschädigt!

die rotgestreifte Seite auf Stift 1

Deutsch

26

Seriell-ATAII-Anschlüsse Diese sechs Serial ATAII-

(SATAII_1 (PORT 0): siehe S.2 - No. 20)

(SATAII_2 (PORT 1): siehe S.2 - No. 19)

(SATAII_3 (PORT 2): siehe S.2 - No. 18)

(SATAII_4 (PORT 3): siehe S.2 - No. 17)

(SATAII_5 (PORT 4): siehe S.2 - No. 16)

(SATAII_6 (PORT 5): siehe S.2 - No. 15)

Datenübertragungsrate bis

(SATAII-)Verbínder
unterstützten SATA-Datenkabel
für interne
Massenspeichergeräte. Die
aktuelle SATAII-Schnittstelle
ermöglicht eine

SATAII_2 SATAII_4
(PORT 1) (PORT 3)

SATAII_6
(PORT 5)

SATAII_5
(PORT 4)

3,0 Gb/s.

SATAII_1 SATAII_3
(PORT 0) (PORT 2)

ASRock 980DE3/U3S3 R2.0 Motherboard

P-7

P+7

GND

DUM MY

USB _PWR

USB _PWR

P-6

P+6

GND

1

Seriell-ATA3-Anschlüsse Diese zwei Serial ATA3-

(SATA3_1 (PORT 6): siehe S.2 - No. 11)

(SATA3_2 (PORT 7): siehe S.2 - No. 9)

SATA3_2

(SATA3-)Verbínder

(PORT 7)

unterstützten SATA-Datenkabel
für interne
Massenspeichergeräte. Die

aktuelle SATA3- Schnittstelle

SATA3_1
(PORT 6)

ermöglicht eine
Datenübertragungsrate bis
6,0 Gb/s.

Serial ATA- (SATA-) SJedes Ende des SATA
Datenkabel Datenkabels kann an die

(Option)

SATA / SATAII / SATA3
Festplatte oder das SATA3
Verbindungsstück auf dieser
Hauptplatine angeschlossen
werden.

USB 2.0-Header Zusätzlich zu den vier

(9-pol. USB4_5)

(siehe S.2 - No. 22)

üblichen USB 2.0-Ports an den

I/O-Anschlüssen benden sich

drei USB 2.0-
Anschlussleisten am
Motherboard. Pro USB 2.0-

(9-pol. USB6_7)

(siehe S.2 - No. 21)

Anschlussleiste werden zwei

USB 2.0-Ports unterstützt.

(9-pol. USB8_9)
(siehe S.2 - No. 23)

1

USB _PWR

P-9

P-8

USB _PWR

P+9

P+8

GND

GND

DUM MY

Infrarot-Modul-Header Dieser Header unterstützt ein

(5-pin IR1)

optionales, drahtloses Sende-

(siehe S.2 - No. 31)

und Empfangs-Infrarotmodul.

ASRock 980DE3/U3S3 R2.0 Motherboard

Deutsch

27

CD- L

GND

GND

CD- R

Interne Audio-Anschlüsse Diese ermöglichen Ihnen

(4-Pin CD1)

(siehe S.2 - No. 28)

Stereo-Signalquellen, wie z. B.

CD-ROM, DVD-ROM, TV-Tuner

CD1

oder MPEG-Karten mit Ihrem
System zu verbinden.

Anschluss für Audio auf Dieses Interface zu einem
der Gehäusevorderseite Audio-Panel auf der Vorder

(9-Pin HD_AUDIO1)

(siehe S.2 - No. 29)

seite Ihres Gehäuses,

ermöglicht Ihnen eine bequeme
Anschlussmöglichkeit und
Kontrolle über Audio-Geräte.

1. High Denition Audio unterstützt Jack Sensing (automatische Erkennung

falsch angeschlossener Geräte), wobei jedoch die Bildschirmverdrahtung
am Gehäuse HDA unterstützen muss, um richtig zu funktionieren.
Beachten Sie bei der Installation im System die Anweisungen in unserem
Handbuch und im Gehäusehandbuch.

2. Wenn Sie die AC’97-Audioleiste verwenden, installieren Sie diese wie
nachstehend beschrieben an der Front-Audioanschlussleiste:
A. Schließen Sie Mic_IN (MIC) an MIC2_L an.
B. Schließen Sie Audio_R (RIN) an OUT2_R und Audio_L (LIN) an OUT2_L an.
C. Schließen Sie Ground (GND) an Ground (GND) an.

D. MIC_RET und OUT_RET sind nur für den HD-Audioanschluss gedacht. Diese

Anschlüsse müssen nicht an die AC’97-Audioleiste angeschlossen werden.
E. So aktivieren Sie das Mikrofon an der Vorderseite.
Bei den Betriebssystemen Windows® XP / XP 64 Bit:

Wählen Sie „Mixer“. Wählen Sie „Recorder“ (Rekorder). Klicken Sie dann
auf „FrontMic“ (Vorderes Mikrofon).

Bei den Betriebssystemen Windows® 8.1 / 8.1 64 Bit / 8 / 8 64 Bit / 7 / 7 64 Bit /
VistaTM / VistaTM 64 Bit:

Wählen Sie im Realtek-Bedienfeld die „FrontMic“ (Vorderes Mikrofon)-
Registerkarte. Passen Sie die „Recording Volume“ (Aufnahmelautstärke)

an.

Deutsch

28

System Panel-Header Dieser Header unterstützt

(9-pin PANEL1)

(siehe S.2 - No. 24)

mehrere Funktion der

Systemvorderseite.

ASRock 980DE3/U3S3 R2.0 Motherboard

Schließen Sie die Ein-/Austaste, die Reset-Taste und die
Systemstatusanzeige am Gehäuse an diesen Header an; befolgen Sie
dabei die nachstehenden Hinweise zur Pinbelegung. Beachten Sie die
positiven und negativen Pins, bevor Sie die Kabel anschließen.

PWRBTN (Ein-/Ausschalter):

Zum Anschließen des Ein-/Ausschalters an der Frontblende des Gehäu

ses. Sie können kongurieren, wie das System mit Hilfe des

Ein-/Ausschalters ausgeschaltet werden können soll.

RESET (Reset-Taste):

Zum Anschließen der Reset-Taste an der Frontblende des Gehäuses.
Mit der Reset-Taste können Sie den Computer im Falle eines Absturzes
neu starten.

PLED (Systembetriebs-LED):

Zum Anschließen der Betriebsstatusanzeige an der Frontblende des
Gehäuses. Die LED leuchtet, wenn das System in Betrieb ist. Die LED

blinkt, wenn sich das System im Ruhezustand S1 bendet. Die LED
schaltet sich aus, wenn sich das System in den Modi S3/S4 bendet

oder ausgeschaltet ist (S5).

HDLED (Festplattenaktivitäts-LED):

Zum Anschließen der Festplattenaktivitäts-LED an der Frontblende des
Gehäuses. Die LED leuchtet, wenn die Festplatte Daten liest oder
schreibt.

Das Design der Frontblende kann je nach Gehäuse variiere. Ein
Frontblendenmodul besteht hauptsächlich aus einer Ein-/Austaste, einer
Reset-Taste, einer Betriebs-LED, einer Festplattenaktivitäts-LED,
Lautsprechern, etc. Stellen Sie beim Anschließen des
Frontblendenmoduls Ihres Gehäuses an diesem Header sicher, dass die
Kabel- und Pinbelegung korrekt übereinstimmen.

Gehäuselautsprecher-Header Schließen Sie den

(4-pin SPEAKER1)

(siehe S.2 - No. 26)

Betriebs-LED-Header Bitte schließen Sie die

(3-pin PLED1)

(siehe S.2 - No. 25)

Gehäuselautsprecher an

diesen Header an.

Betriebs-LED des Gehäuses

zur Anzeige des

1

PLE D+

PLE D+

PLE D-

Systembetriebsstatus an
diesem Header an. Die LED
leuchtet, wenn das System in
Betrieb ist. Die LED blinkt im
S1-Zustand. Im S3-/S4- oder
S5-Zustand (ausgeschaltet)
leuchtet die LED nicht.

ASRock 980DE3/U3S3 R2.0 Motherboard

Deutsch

29

Gehäuse- und Stromlüfteranschlüsse Verbinden Sie die Lüfterkabel

(4-pin CHA_FAN1)

(siehe S.2, No. 12)

den Schutzleiterstift

(4-pin PWR_FAN1)

(siehe S.2 - No. 2)

mit den Lüfteranschlüssen,

wobei der schwarze Draht an

FAN _SPE ED_C ONTR OL

PWR _FAN _SPE ED

+12 V

GND

angeschlossenwird.

Deutsch

CPU-Lüfteranschluss Verbinden Sie das CPU -

(4-pin CPU_FAN1)

(siehe S.2 - No. 3)

Lüfterkabel mit diesem

Anschluss und passen Sie den
schwarzen Draht dem
Erdungsstift an.

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Obwohl dieses Motherboard einen vierpoligen CPU-Lüfteranschluss

(Quiet Fan) bietet, können auch CPU-Lüfter mit dreipoligem Anschluss

angeschlossen werden; auch ohne Geschwindigkeitsregulierung. Wenn
Sie einen dreipoligen CPU-Lüfter an den CPU-Lüferanschluss dieses
Motherboards anschließen möchten, verbinden Sie ihn bitte mit den
Pins 1 – 3.

Pins 1–3 anschließen

Lüfter mit dreipoligem Anschluss installieren

ATX-Netz-Header Verbinden Sie die ATX-

(24-pin ATXPWR1)

(siehe S.2 - No. 10)

Obwohl dieses Motherboard einen 24-pol. ATX-

Stromversorgung mit diesem
Header.

12 124

13

12

24

Stromanschluss bietet, kann es auch mit einem

modizierten traditionellen 20-pol. ATX-Netzteil

verwendet werden. Um ein 20-pol. ATX-Netzteil zu
verwenden, stecken Sie den Stecker mit Pin 1 und
Pin 13 ein.

Installation eines 20-pol. ATX-Netzteils

1

13

ATX 12V Anschluss Bitte schließen Sie an diesen

(8-pin ATX12V1)

(siehe S.2 - No. 1)

Anschluss die ATX 12V

Stromversorgung an.

5 1

8 4

30

ASRock 980DE3/U3S3 R2.0 Motherboard