ASRock 880GMH-USB3 User Manual

0 (0)

No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published May 2010

English

ASRock 880GMH/USB3 Motherboard

Motherboard Layout

English

1	PS2_USB_PW1 Jumper	19	SATAII Connector (SATAII_2 (PORT 1), Blue)
2	CPU Fan Connector (CPU_FAN1)	20	SATAII Connector (SATAII_1 (PORT 0), Blue)
3	ATX 12V Power Connector (ATX12V1)	21	System Panel Header (PANEL1, White)
4	CPU Heatsink Retention Module	22	Chassis Speaker Header
5	AM3 CPU Socket		(SPEAKER 1, White)
6	2 x 240-pin DDR3 DIMM Slots	23	USB 2.0 Header (USB10_11, Blue)
	(Dual Channel A: DDR3_A1, DDR3_B1; Blue)	24	Clear CMOS Jumper (CLRCMOS1)
7	2 x 240-pin DDR3 DIMM Slots	25	Infrared Module Header (IR1)
	(Dual Channel B: DDR3_A2, DDR3_B2; White)	26	Floppy Connector (FLOPPY1)
8	ATX Power Connector (ATXPWR1)	27	Serial Port Connector (COM1)
9	USB_PW1 Jumper	28	Internal Audio Connector: CD1 (Black)
10	Primary IDE Connector (IDE1, Blue)	29	Front Panel Audio Header
11	USB 2.0 Header (USB6_7, Blue)		(HD_AUDIO1, White)
12	Chassis Fan Connector (CHA_FAN1)	30	PCI Slots (PCI1-2)
13	USB 2.0 Header (USB8_9, Blue)	31	PCI Express 2.0 x16 Slot (PCIE2; Blue)
14	Southbridge Controller	32	PCI Express 2.0 x1 Slot (PCIE1; White)
15	SPI Flash Memory (8Mb)	33	Power Fan Connector (PWR_FAN1)
16	SATAII Connector (SATAII_5 (PORT 4), Blue)	34	Northbridge Controller
17	SATAII Connector (SATAII_4 (PORT 3), Blue)	35	USB_PW2 Jumper
18	SATAII Connector (SATAII_3 (PORT 2), Blue)

ASRock 880GMH/USB3 Motherboard

I/O Panel

1	USB 2.0 Ports (USB23)	** 9	Front Speaker (Lime)
2	VGA/D-Sub Port	10	Microphone (Pink)
3	USB 2.0 Ports (USB45)	11	USB 2.0	Port (USB0)
* 4	LAN RJ-45 Port	12	USB 3.0	Port (USB1)
5	Central / Bass (Orange)	13	eSATAII Port (eSATA1)
6	Rear Speaker (Black)	14	VGA/HDMI Port
7	Optical SPDIF Out Port	15	VGA/DVI-D Port
8	Line In (Light Blue)	16	PS/2 Keyboard Port (Purple)

*There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.

LAN Port LED Indications

Activity/Link LED			SPEED LED		ACT/LINK	SPEED
Activity/Link LED			SPEED LED		LED	LED
Status	Description	Status		Description	LED	LED
Status	Description	Status		Description
Off	No Link	Off		10Mbps connection
Blinking	Data Activity	Orange		100Mbps connection

On	Link	Green		1Gbps connection	LAN Port
					LAN Port

**If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels	Front Speaker	Rear Speaker	Central / Bass	Line In
	(No. 9)	(No. 6)	(No. 5)	(No. 8)
2	V	--	--	--
4	V	V	--	--
6	V	V	V	--
8	V	V	V	V

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click

“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio.

English

ASRock 880GMH/USB3 Motherboard

1. Introduction

Thank you for purchasing ASRock 880GMH/USB3 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.

In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-step guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Support CD.

Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit our website for specific information about the model you are using. www.asrock.com/support/index.asp

1.1Package Contents

ASRock 880GMH/USB3 Motherboard

(Micro ATX Form Factor: 9.6-in x 9.0-in, 24.4 cm x 22.9 cm) ASRock 880GMH/USB3 Quick Installation Guide

ASRock 880GMH/USB3 Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor) 2 x Serial ATA (SATA) Data Cables (Optional)

1 x I/O Panel Shield

English

ASRock 880GMH/USB3 Motherboard

1.2Specifications

Platform	- Micro ATX Form Factor: 9.6-in x 9.0-in, 24.4 cm x 22.9 cm
	- All Solid Capacitor design (100% Japan-made high-quality
	Polymer Capacitors)

CPU	- Support for Socket AM3 processors: AMD PhenomTM II X6 /
	X4 / X3 / X2 (except 920 / 940) / Athlon II X4 / X3 / X2 /
	Sempron processors
	- Six-Core CPU Ready
	- Supports AMD OverDriveTM with ACC feature (Advanced
	Clock Calibration)
	- Supports AMD’s Cool ‘n’ QuietTM Technology
	- FSB 2600 MHz (5.2 GT/s)
	- Supports Untied Overclocking Technology (see CAUTION 1)
	- Supports Hyper-Transport 3.0 (HT 3.0) Technology
Chipset	- Northbridge: AMD 880G
	- Southbridge: AMD SB710
Memory	- Dual Channel DDR3 Memory Technology (see CAUTION 2)
	- 4 x DDR3 DIMM slots
	- Support DDR3 1800(OC)/1600(OC)/1333/1066/800 non-ECC,
	un-buffered memory (see CAUTION 3)
	- Max. capacity of system memory: 16GB (see CAUTION 4)
Expansion Slot	- 1 x PCI Express 2.0 x16 slot (blue @ x16 mode)
	- 1 x PCI Express 2.0 x1 slot
	- 2 x PCI slots
	- Supports ATITM Hybrid CrossFireXTM
Graphics	- Integrated AMD Radeon HD 4250 graphics
	- DX10.1 class iGPU, Shader Model 4.1
	- Max. shared memory 512MB (see CAUTION 5)
	- Three VGA Output options: D-Sub, DVI-D and HDMI
	- Supports HDMI Technology with max. resolution up to
	1920x1200 (1080P)
	- Supports Dual-link DVI with max. resolution up to 2560x1600
	@ 75Hz
	- Supports D-Sub with max. resolution up to 2048x1536
	@ 85Hz
	- Supports HDCP function with DVI and HDMI ports
	- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback
	with DVI and HDMI ports

English

ASRock 880GMH/USB3 Motherboard

English

Audio	- 7.1 CH HD Audio with Content Protection
	(Realtek ALC892 Audio Codec)
	- Premium Blu-ray audio support
LAN	- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
	- Realtek RTL8111DL
	- Supports Wake-On-LAN

Rear Panel I/O	I/O Panel
	- 1 x PS/2 Keyboard Port
	- 1 x VGA/D-Sub Port
	- 1 x VGA/DVI-D Port
	- 1 x HDMI Port
	- 1 x Optical SPDIF Out Port
	- 5 x Ready-to-Use USB 2.0 Ports
	- 1 x eSATAII Connector
	- 1 x Ready-to-Use USB 3.0 Port
	- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)
	- HD Audio Jack: Rear Speaker/Central/Bass/Line in/
	Front Speaker/Microphone (see CAUTION 6)
USB 3.0	- 1 x USB 3.0 port by Fresco FL1000G, supports USB 3.0 up to
	5Gb/s
Connector	- 5 x Serial ATAII 3.0Gb/s connectors, support RAID (RAID 0,
	RAID 1, RAID 10 and JBOD), NCQ, AHCI and “Hot Plug”
	functions (see CAUTION 7)
	- 1 x ATA133 IDE connector (supports 2 x IDE devices)
	- 1 x Floppy connector
	- 1 x IR header
	- 1 x COM port header
	- CPU/Chassis/Power FAN connector
	- 24 pin ATX power connector
	- 4 pin 12V power connector
	- CD in header
	- Front panel audio connector
	- 3 x USB 2.0 headers (support 6 USB 2.0 ports)
BIOS Feature	- 8Mb AMI BIOS
	- AMI Legal BIOS
	- Supports “Plug and Play”
	- ACPI 1.1 Compliance Wake Up Events
	- Supports jumperfree
	- SMBIOS 2.3.1 Support
	- VCCM, NB, SB Voltage Multi-adjustment

ASRock 880GMH/USB3 Motherboard

Support CD	- Drivers, Utilities, AntiVirus Software (Trial Version), AMD
	OverDriveTM Utility, AMD Live! Explorer, AMD Fusion, ASRock
	Software Suite (CyberLink DVD Suite - OEM and Trial;
	Creative Sound Blaster X-Fi MB - Trial)
Unique Feature	- ASRock OC Tuner (see CAUTION 8)
	- Intelligent Energy Saver (see CAUTION 9)
	- Instant Boot
	- ASRock Instant Flash (see CAUTION 10)
	- ASRock OC DNA (see CAUTION 11)
	- Hybrid Booster:
	- CPU Frequency Stepless Control (see CAUTION 12)
	- ASRock U-COP (see CAUTION 13)
	- Boot Failure Guard (B.F.G.)
	- Turbo 40 / Turbo 50 GPU Overclocking
Hardware	- CPU Temperature Sensing
Monitor	- Chassis Temperature Sensing
	- CPU/Chassis/Power Fan Tachometer
	- CPU Quiet Fan
	- Voltage Monitoring: +12V, +5V, +3.3V, Vcore
OS	- Microsoft® Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit
	/ XP / XP Media Center / XP 64-bit compliant
Certifications	- FCC, CE, WHQL
	- ErP/EuP Ready (ErP/EuP ready power supply is required)
	(see CAUTION 14)

* For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using the thirdparty overclocking tools. Overclocking may affect your system stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.

English

ASRock 880GMH/USB3 Motherboard

English

CAUTION!

1.This motherboard supports Untied Overclocking Technology. Please read “Untied Overclocking Technology” on page 26 for details.

2.This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 12 for proper installation.

3.Whether 1800/1600MHz memory speed is supported depends on the AM3 CPU you adopt. If you want to adopt DDR3 1800/1600 memory module on this motherboard, please refer to the memory support list on our website for the compatible memory modules.

ASRock website http://www.asrock.com

4.Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® 7 / VistaTM / XP. For Windows® OS with 64-bit CPU, there is no such limitation.

5.The maximum shared memory size is defined by the chipset vendor and is subject to change. Please check AMD website for the latest information.

6.For microphone input, this motherboard supports both stereo and mono modes. For audio output, this motherboard supports 2-channel, 4-channel, 6-channel, and 8-channel modes. Please check the table on page 3 for proper connection.

7.Before installing SATAII hard disk to SATAII connector, please read the “SATAII Hard Disk Setup Guide” on page 28 of “User Manual” in the support CD to adjust your SATAII hard disk drive to SATAII mode. You can also connect SATA hard disk to SATAII connector directly.

8.It is a user-friendly ASRock overclocking tool which allows you to surveil your system by hardware monitor function and overclock your hardware devices to get the best system performance under Windows® environment. Please visit our website for the operation procedures of ASRock OC Tuner. ASRock website: http://www.asrock.com

9.Featuring an advanced proprietary hardware and software design, Intelligent Energy Saver is a revolutionary technology that delivers unparalleled power savings. The voltage regulator can reduce the number of output phases to improve efficiency when the CPU cores are idle. In other words, it is able to provide exceptional power saving and improve power efficiency without sacrificing computing performance. To use Intelligent Energy Saver function, please enable Cool ‘n’ Quiet option in the BIOS setup in advance. Please visit our website for the operation procedures of Intelligent Energy Saver.

ASRock website: http://www.asrock.com

ASRock 880GMH/USB3 Motherboard

10.ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM. This convenient BIOS update tool allows you to update system BIOS without entering operating systems first like MS-DOS or Windows®. With this utility, you can press <F6> key during the POST or press <F2> key to BIOS setup menu to access ASRock Instant Flash. Just launch this tool and save the new BIOS file to your USB flash drive, floppy disk or hard drive, then you can update your BIOS only in a few clicks without preparing an additional floppy diskette or other complicated flash utility. Please be noted that the USB flash drive or hard drive must use FAT32/16/12 file system.

11.The software name itself – OC DNA literally tells you what it is capable of. OC DNA, an exclusive utility developed by ASRock, provides a convenient way for the user to record the OC settings and share with others. It helps you to save your overclocking record under the operating system and simplifies the complicated recording process of overclocking settings. With OC DNA, you can save your OC settings as a profile and share with your friends! Your friends then can load the OC profile to their own system to get the same OC settings as yours! Please be noticed that the OC profile can only be shared and worked on the same motherboard.

12.Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU.

13.While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system.

14.EuP, stands for Energy Using Product, was a provision regulated by European Union to define the power consumption for the completed system. According to EuP, the total AC power of the completed system shall be under 1.00W in off mode condition. To meet EuP standard, an EuP ready motherboard and an EuP ready power supply are required. According to Intel’s suggestion, the EuP ready power supply must meet the standard of 5v standby power efficiency is higher than 50% under 100 mA current consumption. For EuP ready power supply selection, we recommend you checking with the power supply manufacturer for more details.

English

ASRock 880GMH/USB3 Motherboard

2. Installation

This is a Micro ATX form factor (9.6-in x 9.0-in, 24.4 cm x 22.9 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

1.Unplug the power cord from the wall socket before touching any component.

2.To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.

3.Hold components by the edges and do not touch the ICs.

4.Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.

5.When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.

English

1 0

ASRock 880GMH/USB3 Motherboard

2.1CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90o angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked.

Lever 90° Up
	CPU Golden Triangle
	Socker Corner Small Triangle
STEP 1:	STEP 2 / STEP 3:	STEP 4:
Lift Up The Socket Lever	Match The CPU Golden Triangle	Push Down And Lock
	To The Socket Corner Small	The Socket Lever
	Triangle

2.2 Installation of CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install a larger heatsink and cooling fan to dissipate heat. You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation. Make sure that the CPU and the heatsink are securely fastened and in good contact with each other. Then connect the CPU fan to the CPU FAN connector (CPU_FAN1, see Page 2, No. 2). For proper installation, please kindly refer to the instruction manuals of the CPU fan and the heatsink.

English

1 1

ASRock 880GMH/USB3 Motherboard

2.3 Installation of Memory Modules (DIMM)

This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install identical (the same brand, speed, size and chiptype) DDR3 DIMM pair in the slots of the same color. In other words, you have to install identical DDR3 DIMM pair in Dual Channel A (DDR3_A1 and DDR3_B1; Blue slots; see p.2 No.6) or identical DDR3 DIMM pair in Dual Channel B (DDR3_A2 and DDR3_B2; White slots; see p.2 No.7), so that Dual Channel Memory Technology can be activated. This motherboard also allows you to install four DDR3 DIMMs for dual channel configuration, and please install identical DDR3 DIMMs in all four slots. You may refer to the Dual Channel Memory Configuration Table below.

Dual Channel Memory Configurations

	DDR3_A1	DDR3_B1	DDR3_A2	DDR3_B2
	(Blue Slot)	(Blue Slot)	(White Slot)	(White Slot)
(1)	Populated	Populated	-	-
(2)	-	-	Populated	Populated
(3)*	Populated	Populated	Populated	Populated

* For the configuration (3), please install identical DDR3 DIMMs in all four slots.

English

1 2

1.If you want to install two memory modules, for optimal compatibility and reliability, it is recommended to install them in the slots of the same color. In other words, install them either in the set of blue slots (DDR3_A1 and DDR3_B1), or in the set of white slots (DDR3_A2 and DDR3_B2).

2.If only one memory module or three memory modules are installed in the DDR3 DIMM slots on this motherboard, it is unable to activate the Dual Channel Memory Technology.

3.If a pair of memory modules is NOT installed in the same Dual Channel, for example, installing a pair of memory modules in DDR3_A1 and DDR3_A2, it is unable to activate the Dual Channel Memory Technology .

4.It is not allowed to install a DDR or DDR2 memory module into DDR3 slot; otherwise, this motherboard and DIMM may be damaged.

5.If you adopt DDR3 1800/1600 memory modules on this motherboard, it is recommended to install them on DDR3_A2 and DDR3_B2 slots.

ASRock 880GMH/USB3 Motherboard

Installing a DIMM

Please make sure to disconnect power supply before adding or removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.

English

1 3

ASRock 880GMH/USB3 Motherboard

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 2 PCI slots and 2 PCI Express slots on this motherboard.

PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI interface.

PCIE Slots:

PCIE1 (PCIE x1 slot; White) is used for PCI Express cards with x1 lane width cards, such as Gigabit LAN card and SATA2 card.

PCIE2 (PCIE x16 slot; Blue) is used for PCI Express x16 lane width graphics cards.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws for later use.

Step 4. Align the card connector with the slot and press firmly until the card is completely seated on the slot.

Step 5. Fasten the card to the chassis with screws. Step 6. Replace the system cover.

English

1 4

ASRock 880GMH/USB3 Motherboard

2.5 Dual Monitor and Surround Display Features

Dual Monitor Feature

This motherboard supports dual monitor feature. With the internal VGA output support (DVI-D, D-Sub and HDMI), you can easily enjoy the benefits of dual monitor feature without installing any add-on VGA card to this motherboard. This motherboard also provides independent display controllers for DVI-D, D-Sub and HDMI to support dual VGA output so that DVI-D, D-sub and HDMI can drive same or different display contents.

To enable dual monitor feature, please follow the below steps:

1.Connect DVI-D monitor cable to VGA/DVI-D port on the I/O panel, connect D-Sub monitor cable to VGA/D-Sub port on the I/O panel, or connect HDMI monitor cable to HDMI port on the I/O panel.

VGA/D-Sub port

VGA/DVI-D port HDMI port

2.If you have installed onboard VGA driver from our support CD to your system already, you can freely enjoy the benefits of dual monitor function after your system boots. If you haven’t installed onboard VGA driver yet, please install onboard VGA driver from our support CD to your system and restart your computer. Then you can start to use dual monitor function on this motherboard.

1.DVI-D and HDMI ports cannot function at the same time. When one of them is enabled, the other one will be disabled.

2.When you playback HDCP-protected video from Blu-ray (BD) or HD-DVD disc, the content will be displayed only in one of the two monitors instead of both monitors.

English

1 5

ASRock 880GMH/USB3 Motherboard

English

1 6

Surround Display Feature

This motherboard supports surround display upgrade. With the internal VGA output support (DVI-D, D-Sub and HDMI) and external add-on PCI Express VGA cards, you can easily enjoy the benefits of surround display feature.

Please refer to the following steps to set up a surround display environment:

1.Install the ATITM PCI Express VGA card on PCIE2 slot. Please refer to page 14 for proper expansion card installation procedures for details.

2.Connect DVI-D monitor cable to VGA/DVI-D port on the I/O panel, connect D-Sub monitor cable to VGA/D-Sub port on the I/O panel, or connect HDMI monitor cable to HDMI port on the I/O panel. Then connect other monitor cables to the corresponding connectors of the add-on PCI Express VGA card on PCIE2 slot.

3.Boot your system. Press <F2> to enter BIOS setup. Enter “Share Memory” option to adjust the memory capability to [32MB], [64MB], [128MB] [256MB] or [512MB] to enable the function of VGA/D-sub. Please make sure that the value you select is less than the total capability of the system memory. If you do not adjust the BIOS setup, the default value of “Share Memory”, [Auto], will disable VGA/D-Sub function when the add-on VGA card is inserted to this motherboard.

4.Install the onboard VGA driver and the add-on PCI Express VGA card driver to your system. If you have installed the drivers already, there is no need to install them again.

5.Set up a multi-monitor display.

For Windows® XP / XP 64-bit OS:

Right click the desktop, choose “Properties”, and select the “Settings” tab so that you can adjust the parameters of the multi-monitor according to the steps below.

A.Click the “Identify” button to display a large number on each monitor.

B.Right-click the display icon in the Display Properties dialog that you wish to be your primary monitor, and then select “Primary”. When you use multiple monitors with your card, one monitor will always be Primary, and all additional monitors will be designated as Secondary.

C.Select the display icon identified by the number 2.

D.Click “Extend my Windows desktop onto this monitor”.

E.Right-click the display icon and select “Attached”, if necessary.

F.Set the “Screen Resolution” and “Color Quality” as appropriate for the second monitor. Click “Apply” or “OK” to apply these new values.

G.Repeat steps C through E for the diaplay icon identified by the number one, two, three and four.

ASRock 880GMH/USB3 Motherboard

For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:

Right click the desktop, choose “Personalize”, and select the “Display Settings” tab so that you can adjust the parameters of the multi-monitor according to the steps below.

A.Click the number ”2” icon.

B.Click the items “This is my main monitor” and “Extend the desktop onto this monitor”.

C.Click “OK” to save your change.

D.Repeat steps A through C for the display icon identified by the number three and four.

6.Use Surround Display. Click and drag the display icons to positions representing the physical setup of your monitors that you would like to use. The placement of display icons determines how you move items from one monitor to another.

HDCP Function

HDCP function is supported on this motherboard. To use HDCP function with this motherboard, you need to adopt the monitor that supports HDCP function as well. Therefore, you can enjoy the superior display quality with high-definition HDCP encryption contents. Please refer to below instruction for more details about HDCP function.

What is HDCP?

HDCP stands for High-Bandwidth Digital Content Protection, a specification developed by Intel® for protecting digital entertainment content that uses the DVI interface. HDCP is a copy protection scheme to eliminate the possibility of intercepting digital data midstream between the video source, or transmitter - such as a computer, DVD player or set-top box - and the digital display, or receiver - such as a monitor, television or projector. In other words, HDCP specification is designed to protect the integrity of content as it is being transmitted.

Products compatible with the HDCP scheme such as DVD players, satellite and cable HDTV set-top-boxes, as well as few entertainment PCs requires a secure connection to a compliant display. Due to the increase in manufacturers employing HDCP in their equipment, it is highly recommended that the HDTV or LCD monitor you purchase is compatible.

1 7

English

ASRock 880GMH/USB3 Motherboard

English

2.6ATITM Hybrid CrossFireXTM Operation Guide

This motherboard supports ATITM Hybrid CrossFireXTM feature. ATITM Hybrid CrossFireXTM brings multi-GPU performance capabilities by enabling an AMD 880G integrated graphics processor and a discrete graphics processor to operate simultaneously with combined output to a single display for blisteringly-fast frame rates. Currently, ATITM Hybrid CrossFireXTM Technology is only supported with Windows® VistaTM / 7 OS, and is not available with Windows® XP OS. In the future, ATITM Hybrid CrossFireXTM may be supported with Windows® XP OS. Please visit our website for updated information.

What does an ATITM Hybrid CrossFireXTM system include?

An ATITM Hybrid CrossFireXTM system includes an ATITM RadeonTM 2400 or ATITM RadeonTM 3450 series graphics processor and a motherboard based on an AMD 880G integrated chipset, all operating in a Windows® VistaTM / 7 environment. Please refer to below PCI Express graphics card support list for ATITM Hybrid CrossFireXTM. For the future update of more compatible PCI Express graphics cards, please visit our website for further information.

Vendor	Chipset	Model	Driver
ATI	RADEON HD2400XT	POWERCOLOR HD2400 XT	Support CD 8.71
		256MB DDR3
	RADEON HD3450	POWERCOLOR AX3450	Support CD 8.71
		256MD2-S

Enjoy the benefit of ATITM Hybrid CrossFireXTM

Step 1. Install one compatible PCI Express graphics card to PCIE2 slot (blue). For the proper installation procedures, please refer to section “Expansion Slots”.

Step 2. Connect the monitor cable to the correspondent connector on the PCI Express graphics card on PCIE2 slot.

Step 3. Boot your system. Press <F2> to enter BIOS setup. Enter “Advanced” screen, and enter “Chipset Settings”. Then set the option “Surround View” to [Enabled].

Step 4. Boot into OS. Please remove the ATITM driver if you have any VGA driver installed in your system.

Step 5. Install the onboard VGA driver from our support CD to your system for both the onboard VGA and the discrete graphics card.

Step 6. Restart your computer. Then you will find “ATI Catalyst Control Center” on your Windows® taskbar.

ATI Catalyst Control Center

1 8

ASRock 880GMH/USB3 Motherboard

Step 7. Double-click “ATI Catalyst Control Center”. Click “View”, click “CrossFireTM”, and then select the option “Enable CrossFireTM”.

View

CrossFireTM		Enable CrossFireTM

Step 8. Click “Yes” to continue.

Step 9. Click “OK” to save your change.

Step 10. Reboot your system. Then you can freely enjoy the benefit of HybridTM CrossFireXTM feature.

*Hybrid CrossFireXTM appearing here is a registered trademark of ATITM Technologies Inc., and is used only for identification or explanation and to the owners’ benefit, without intent to infringe.

*For further information of ATITM Hybrid CrossFireXTM technology, please check AMD website for up dates and details.

1 9

English

ASRock 880GMH/USB3 Motherboard

English

2.7Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is Short Open placed on these 2 pins.

Jumper	Setting
PS2_USB_PW1	Short pin2, pin3 to enable
(see p.2, No. 1)	+5VSB (standby) for PS/2 or
	USB23 wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power supply.

USB_PW2	Short pin2, pin3 to enable
(see p.2, No. 35)	+5V_DUAL for USB01/45
	wake up events.

Note: To select +5V_DUAL, it requires 2 Amp and higher standby current provided by power supply. When you select +5V_DUAL, USB devices can wake up the system under S3 (Suspend to RAM) state. To support ErP/EuP requirement, please set this jumper to +5V.

USB_PW1	Short pin2, pin3 to enable
(see p.2, No. 9)	+5VSB (standby) for
	USB6_7/8_9/10_11 wake up
	events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power supply.

Clear CMOS Jumper

(CLRCMOS1)

(see p.2, No. 24) Default Clear CMOS

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action.

2 0

ASRock 880GMH/USB3 Motherboard

2.8 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

•

Floppy Connector

(33-pin FLOPPY1)

(see p.2 No. 26)

the red-striped side to Pin1

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector.

Primary IDE connector (Blue)

(39-pin IDE1, see p.2 No. 10)

connect the blue end	connect the black end
to the motherboard	to the IDE devices

80-conductor ATA 66/100/133 cable

Note: Please refer to the instruction of your IDE device vendor for the details.

Serial ATAII Connectors		These five Serial ATAII (SATAII)
(SATAII_1 (PORT 0):		connectors support SATAII
see p.2, No. 20)		or SATA hard disk for internal
(SATAII_2 (PORT 1):		storage devices. The current
see p.2, No. 19)		SATAII interface allows up to
(SATAII_3 (PORT 2):		3.0 Gb/s data transfer rate.
see p.2, No. 18)	SATAII_1 SATAII_2 SATAII_3 SATAII_4	SATAII_5
(SATAII_4 (PORT 3):	SATAII_1 SATAII_2 SATAII_3 SATAII_4	SATAII_5
(SATAII_4 (PORT 3):	(PORT 0) (PORT 1) (PORT 2) (PORT 3) (PORT 4)
see p.2, No. 17)
(SATAII_5 (PORT 4):
see p.2, No. 16)

Serial ATA (SATA)		Either end of the SATA data cable
Data Cable		can be connected to the SATA /
(Optional)		SATAII hard disk or the SATAII
		connector on the motherboard.

2 1

English

ASRock 880GMH/USB3 Motherboard

USB 2.0 Headers	Besides five default USB 2.0
(9-pin USB6_7)	ports on the I/O panel, there are
(see p.2 No. 11)	three USB 2.0 headers on this
	motherboard. Each USB 2.0
	header can support two USB
	2.0 ports.
(9-pin USB8_9)
(see p.2 No. 13)

(9-pin USB10_11)

(see p.2 No. 23)

Infrared Module Header		This header supports an
(5-pin IR1)		optional wireless transmitting
(see p.2 No. 25)		and receiving infrared module.

Internal Audio Connectors		This connector allows you
(4-pin CD1)	CD1	to receive stereo audio input
(CD1: see p.2 No. 28)	CD1	from sound sources such as
(CD1: see p.2 No. 28)		from sound sources such as
		a CD-ROM, DVD-ROM, TV
		tuner card, or MPEG card.

Front Panel Audio Header		This is an interface for the front
(9-pin HD_AUDIO1)		panel audio cable that allows
(see p.2, No. 29)		convenient connection and
		control of audio devices.

English

2 2

1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2.If you use AC’97 audio panel, please install it to the front panel audio header as below:

A.Connect Mic_IN (MIC) to MIC2_L.

B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C.Connect Ground (GND) to Ground (GND).

ASRock 880GMH/USB3 Motherboard

D.MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.

E.To activate the front mic.

For Windows® XP / XP 64-bit OS:

Select “Mixer”. Select “Recorder”. Then click “FrontMic”. For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:

Go to the "FrontMic" Tab in the Realtek Control panel. Adjust “Recording Volume”.

System Panel Header	This header accommodates
(9-pin PANEL1)	several system front panel
(see p.2 No. 21)	functions.

Chassis Speaker Header			Please connect the chassis
(4-pin SPEAKER 1)			speaker to this header.
(see p.2	No. 22)

Chassis and Power Fan Connectors			Please connect the fan cables
(3-pin CHA_FAN1)			to the fan connectors and
(see p.2	No. 12)		match the black wire to the
(3-pin PWR_FAN1)
(see p.2	No. 33)

CPU Fan Connector		1	Please connect the CPU fan
		1	cable to this connector and
(4-pin CPU_FAN1)		2	cable to this connector and
		3	match the black wire to the
(see p.2	No. 2)	4	match the black wire to the

ground pin.

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.

			Pin 1-3 Connected
			3-Pin Fan Installation

ATX Power Connector	12	24	Please connect an ATX power
(24-pin ATXPWR1)			supply to this connector.
(see p.2 No. 8)
	1	13

2 3

English

ASRock 880GMH/USB3 Motherboard

	Though this motherboard provides 24-pin ATX power connector,		12	24
	it can still work if you adopt a traditional 20-pin ATX power supply.

	To use the 20-pin ATX power supply, please plug your power
	supply along with Pin 1 and Pin 13.
		20-PinATX Power Supply Installation	1	13



ATX 12V Power Connector		Please connect an ATX 12V
(4-pin ATX12V1)		power supply to this connector.
(see p.2 No. 3)

Serial port Header		This COM1 header supports a
(9-pin COM1)		serial port module.
(see p.2 No.27)

English

2 4

ASRock 880GMH/USB3 Motherboard

2.9Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical drive first. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.

2.10 Installing Windows® 7 / 7 64-bit / VistaTM /

VistaTM 64-bit / XP / XP 64-bit With RAID Functions

If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit on your SATA / SATAII HDDs with RAID functions, please refer to the document at the following path in the Support CD for detailed procedures:

..\ RAID Installation Guide

2.11 Installing Windows® 7 / 7 64-bit / VistaTM /

VistaTM 64-bit / XP / XP 64-bit Without RAID Functions

If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit OS on your SATA / SATAII HDDs without RAID functions, please follow below procedures according to the OS you install.

2.11.1 Installing Windows® XP / XP 64-bit Without RAID Functions

If you want to install Windows® XP / XP 64-bit on your SATA / SATAII HDDs without RAID functions, please follow below steps.

Using SATA / SATAII HDDs without NCQ and Hot Plug functions (IDE mode) STEP 1: Set up BIOS.

A.	Enter BIOS SETUP UTILITY		Advanced screen		Storage

Configuration.

B.Set the “SATA Operation Mode” option to [IDE].

STEP 2: Install Windows® XP / XP 64-bit OS on your system.

2 5

English

ASRock 880GMH/USB3 Motherboard

English

2.11.2 Installing Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit Without RAID Functions

If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit on your SATA / SATAII HDDs without RAID functions, please follow below steps.

Using SATA / SATAII HDDs without NCQ and Hot Plug functions (IDE mode) STEP 1: Set up BIOS.

A.	Enter BIOS SETUP UTILITY		Advanced screen		Storage

Configuration.

B.Set the “SATA Operation Mode” option to [IDE].

STEP 2: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.

Using SATA / SATAII HDDs with NCQ and Hot Plug functions (AHCI mode)

STEP 1: Set Up BIOS.

A.	Enter BIOS SETUP UTILITY		Advanced screen		Storage

Configuration.

B.Set the “SATA Operation Mode” option to [AHCI].

STEP 2: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.

2.12 Untied Overclocking Technology

This motherboard supports Untied Overclocking Technology, which means during overclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before you enable Untied Overclocking function, please enter “Overclock Mode” option of BIOS setup to set the selection from [Auto] to [CPU, PCIE, Async.]. Therefore, CPU FSB is untied during overclocking, but PCI / PCIE buses are in the fixed mode so that FSB can operate under a more stable overclocking environment.

Please refer to the warning on page 7 for the possible overclocking risk before you apply Untied Overclocking Technology.

2 6

ASRock 880GMH/USB3 Motherboard

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the predetermined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF file) contained in the Support CD.

4. Software Support CD information

This motherboard supports various Microsoft® Windows® operating systems: 7 /

7 64-bit / VistaTM / VistaTM 64-bit / XP / XP Media Center / XP 64-bit. The Support CD that came with the motherboard contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the file “ASSETUP.EXE” from the “BIN” folder in the Support CD to display the menus.

English

2 7

ASRock 880GMH/USB3 Motherboard

1. Einführung

Wir danken Ihnen für den Kauf des ASRock 880GMH/USB3 Motherboard, ein zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design, gemäß der Verpflichtung von ASRock zu Qualität und Halbarkeit.

Diese Schnellinstallationsanleitung führt in das Motherboard und die schrittweise Installation ein. Details über das Motherboard finden Sie in der Bedienungsanleitung auf der Support-CD.

Da sich Motherboard-Spezifikationen und BIOS-Software verändern können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein. Die neuesten Grafikkarten und unterstützten CPUs sind auch auf der ASRock-Website aufgelistet.

ASRock-Website: http://www.asrock.com

Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezifische Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere Webseite:

www.asrock.com/support/index.asp

1.1 Kartoninhalt

ASRock 880GMH/USB3 Motherboard

(Micro ATX-Formfaktor: 24.4 cm x 22.9 cm; 9.6 Zoll x 9.0 Zoll) ASRock 880GMH/USB3 Schnellinstallationsanleitung

ASRock 880GMH/USB3 Support-CD

Ein 80-adriges Ultra-ATA 66/100/133 IDE-Flachbandkabel Zwei Seriell-ATA- (SATA) Datenkabel (Option)

Ein I/O Shield

Deutsch

2 8

ASRock 880GMH/USB3 Motherboard

1.2Spezifikationen

Plattform	- Micro ATX-Formfaktor: 24.4 cm x 22.9 cm; 9.6 Zoll x 9.0 Zoll
	- Alle Feste Kondensatordesign (100% in Japan gefertigte,
	erstklassige leitfähige Polymer-Kondensatoren)

CPU	- Unterstützung von Socket AM3-Prozessoren: AMD PhenomTM
	II X6 / X4 / X3 / X2 (außer 920 / 940) / Athlon X4 / X3 / X2 /
	Sempron-Prozessor
	- Sechs-Kern-CPU-bereit
	- Unterstützt AMD OverDriveTM mit ACC-Funktion (Advanced
	Clock Calibration, Erweiterte Taktkalibrierung)
	- Unterstützt Cool ‘n’ QuietTM-Technologie von AMD
	- FSB 2600 MHz (5.2 GT/s)
	- Unterstützt Untied-Übertaktungstechnologie
	(siehe VORSICHT 1)
	- Unterstützt Hyper-Transport- 3.0 Technologie (HT 3.0)

Chipsatz	- Northbridge: AMD 880G
	- Southbridge: AMD 710

Speicher	- Unterstützung von Dual-Kanal-Speichertechnologie
	(siehe VORSICHT 2)
	- 4 x Steckplätze für DDR3
	- Unterstützt DDR3 1800(OC)/1600(OC)/1333/1066/800
	non-ECC, ungepufferter Speicher (siehe VORSICHT 3)
	- Max. Kapazität des Systemspeichers: 16GB
	(siehe VORSICHT 4)
Erweiterungs-	- 1 x PCI Express 2.0 x16-Steckplatz (blau für x16-Modus)
steckplätze	- 1 x PCI Express 2.0 x1-Steckplatz
	- 2 x PCI -Steckplätze
	- Unterstützt ATITM Hybrid CrossFireXTM
Onboard-VGA	- Integrierte AMD Radeon HD 4250-Grafik
	- DX10.1 Klasse iGPU, Shader Model 4.1
	- Maximal gemeinsam genutzter Speicher 512 MB
	(siehe VORSICHT 5)
	- Drei VGA-Ausgangsoptionen: D-Sub, DVI-D sowie HDMI
	- Unterstützt HDMI mit einer maximalen Auflösung von
	1920 x 1200 (1080p)
	- Unterstützt Dual-Link-DVI mit einer maximalen Auflösung von
	2560 x 1600 bei 75 Hz
	- Unterstützt D-Sub mit einer maximalen Auflösung von
	2048 x 1536 bei 85 Hz

Deutsch

2 9

ASRock 880GMH/USB3 Motherboard

Deutsch

3 0

		- Unterstützt HDCP-Funktion mit DVIund HDMI-Ports
		- Unterstutzt 1080p Blu-ray (BD) / HD-DVD-Wiedergabe mit
		DVIund HDMI-Ports

	Audio	- 7.1 CH HD Audio mit dem Inhalt Schutz
		(Realtek ALC892 Audio Codec)
		- Premium Blu-ray-Audio-Unterstützung

	LAN	- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
		- Realtek RTL8111DL
		- Unterstützt Wake-On-LAN
	E/A-Anschlüsse	I/O Panel
	an der	- 1 x PS/2-Tastaturanschluss
	Rückseite	- 1 x VGA/D-Sub port
		- 1 x VGA/DVI-D port
		- 1 x HDMI port
		- 1 x optischer SPDIF-Ausgang
		- 5 x Standard-USB 2.0-Anschlüsse
		- 1 x eSATAII-Anschluss
		- 1 x Standard-USB 3.0-Anschlüsse
		- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED LED)
		- HD Audiobuchse: Lautsprecher hinten / Mitte/Bass /
		Audioeingang / Lautsprecher vorne / Mikrofon
		(siehe VORSICHT 6)
	USB 3.0	- 1 x USB 3.0-Ports durch Fresco FL1000G; unterstützt
		USB 3.0 mit bis zu 5 Gb/s
	Anschlüsse	- 5 x SATAII-Anschlüsse, unterstützt bis 3.0 Gb/s
		Datenübertragungsrate, unterstützt RAID (RAID 0, RAID 1,
		RAID 10 und JBOD), NCQ, AHCI und “Hot Plug” Funktionen
		(siehe VORSICHT 7)
		- 1 x ATA133 IDE-Anschlüsse (Unterstützt bis 2 IDE-Geräte)
		- 1 x FDD-Anschlüsse
		- 1 x Infrarot-Modul-Header
		- 1 x COM-Anschluss-Header
		- CPU/Gehäuse/Stromlüfter-Anschluss
		- 24-pin ATX-Netz-Header
		- 4-pin anschluss für 12V-ATX-Netzteil
		- Interne Audio-Anschlüsse
		- Anschluss für Audio auf der Gehäusevorderseite
		- 3 x USB 2.0-Anschlüsse (Unterstützung 6 zusätzlicher
		USB 2.0-Anschlüsse)
	BIOS	- 8Mb AMI BIOS
		- AMI legal BIOS mit Unterstützung für “Plug and Play”
		- ACPI 1.1-Weckfunktionen

ASRock 880GMH/USB3 Motherboard

+ 197 hidden pages