ANALOG DEVICES SSM2141 Service Manual
SSM2141
–IN
+IN
SENSE
+V
CC
OUTPUT
–V
EE
REFERENCE
25kΩ 25kΩ
25kΩ25kΩ
1
3
2
5
7
6
4
1
2
3
4
8
7
6
5
TOP VIEW
(Not to Scale)
NC = NO CONNECT
SSM2141
REFERENCE
SENSE
OUTPUT
V+
NC
–IN
+IN
V–
High Common-Mode Rejection
C
781/461-3113
a
FEATURES
High Common-Mode Rejection
DC: 100 dB typ
60 Hz: 100 dB typ
20 kHz: 70 dB typ
40 kHz: 62 dB typ
Low Distortion: 0.001% typ
Fast Slew Rate: 9.5 V/ms typ
Wide Bandwidth: 3 MHz typ
Low Cost
Complements SSM2142 Differential Line Driver
APPLICATIONS
Line Receivers
Summing Amplifiers
Buffer Amplifiers–Drives 600 V Load
GENERAL DESCRIPTION
The SSM2141 is an integrated differential amplifier intended to
receive balanced line inputs in audio applications requiring a
high level of noise immunity and optimum common-mode
rejection. The SSM2141 typically achieves 100 dB of commonmode rejection (CMR), whereas implementing an op amp with
four off-the-shelf precision resistors will typically achieve only
40 dB of CMR—inadequate for high-performance audio.
The SSM2141 achieves low distortion performance by
maintaining a large slew rate of 9.5 V/µs and high open-loop
gain. Distortion is less than 0.002% over the full audio
bandwidth. The SSM2141 complements the SSM2142
balanced line driver. Together, these devices comprise a fully
integrated solution for equivalent transformer balancing of
audio signals without the problems of distortion, EMI fields,
and high cost.
Additional applications for the SSM2141 include summing
signals, differential preamplifiers, and 600 Ω low distortion
buffer amplifiers. For similar performance with G = 1/2, see
SSM2143.
Differential Line Receiver
SSM2141
FUNCTIONAL BLOCK DIAGRAM
PIN CONNECTIONS
8-Pin Plastic Mini-DIP
(P Suffix)
Narrow Body SO
(S Suffix)
REV.
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700 Fax:
SSM2141–SPECIFICA TIONS
C
ELECTRICAL CHARACTERISTICS
(@ VS = 618 V, TA = +258C, unless otherwise noted)
SSM2141
Parameter Symbol Conditions Min Typ Max Units
OFFSET VOLTAGE V
OS
VCM = 0 V –1000 25 1000 µV
GAIN ERROR No Load, VIN = ±10 V, RS = 0 Ω 0.001 0.01 %
INPUT VOLTAGE RANGE IVR (Note 1) ±10 V
COMMON-MODE REJECTION CMR VCM = ±10 V 80 100 dB
POWER SUPPLY REJECTION RATIO PSRR VS = ±6 V to ±18 V 0.7 15 µV/V
OUTPUT SWING V
SHORT-CIRCUIT CURRENT LIMIT I
O
SC
RL = 2 kΩ±13 ±14.7 V
Output Shorted to Ground +45/–15 mA
SMALL-SIGNAL BANDWIDTH (–3 dB) BW RL = 2 kΩ 3 MHz
SLEW RATE SR RL = 2 kΩ 6 9.5 V/µs
TOTAL HARMONIC DISTORTION R
= 100 kΩ 0.001 %
L
THD RL = 600 Ω 0.01
CAPACITIVE LOAD DRIVE CAPABILITY C
SUPPLY CURRENT I
NOTES
1
Input Voltage Range Guaranteed by CMR test.
Specifications subject to change without notice
L
SY
No Oscillation 300 pF
No Load 2.5 3.5 mA
ELECTRICAL CHARACTERISTICS
(@ VS = 618 V, –408C ≤ TA ≤ +858C)
Parameter Symbol Conditions Min Typ Max Units
OFFSET VOLTAGE V
OS
VCM = 0 V –2500 200 2500 µV
GAIN ERROR No Load, VIN = ±10 V, RS = 0 Ω 0.002 0.02 %
INPUT VOLTAGE RANGE IVR (Note 1) ±10 V
COMMON-MODE REJECTION CMR VCM = ±10 V 75 90 dB
POWER SUPPLY REJECTION RATIO PSRR VS = ±6 V to ±18 V 1.0 20 µV/V
OUTPUT SWING V
O
RL = 2 kΩ±13 ±14.7 V
SLEW RATE SR RL = 2 kΩ 9.5 V/µs
SUPPLY CURRENT I
NOTES
1
Input Voltage Range Guaranteed by CMR test.
Specifications subject to change without notice
SY
No Load 2.6 4.0 mA
–2–
REV.
SSM2141
C
ABSOLUTE MAXIMUM RATINGS
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V
Input Voltage
1
. . . . . . . . . . . . . . . . . . . . . . . . Supply Voltage
1
Output Short-Circuit Duration . . . . . . . . . . . . . . Continuous
Storage Temperature Range
P Package . . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . +300°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Operating Temperature Range . . . . . . . . . . . . –40°C to +85°C
Typical Performance Characteristics
Package Type u
2
JA
u
JC
Units
8-Pin Plastic DIP (P) 103 43 °C/W
NOTES
1
For supply voltages less than ±18 V, the absolute maximum input voltage is equal
to the supply voltage.
2
θJA is specified for worst case mounting conditions, i.e., θJA is specified for device
in socket for P-DIP package.
Small Signal Transient Response
Common-Mode Rejection vs. Frequency
Large Signal Transient Response
Power Supply Rejection vs. Frequency
REV.
Total Harmonic Distortion vs. Frequency
–3–
Dynamic Intermodulation Distortion vs. Frequency
Loading...