Alto-Shaam CTP10-10E, CTP6-10E, CTP20-10E, CTP20-20E, CTP10-10G Operator's Manual

...
OPERATOR’S MANUAL
WARNING
WARNING
CT PROFORMANCE™
CTP6-10E
CTP10-10E
CTP7-20E CTP10-20E CTP20-10E CTP20-20E
CTP6-10G
CTP10-10G
CTP7-20G CTP10-20G CTP20-10G CTP20-20G
To prevent personal injury, death or property damage:
Do not store or use gasoline or other
fl ammable vapors or liquids in the vicinity of this or any other appliance.
Improper installation, alteration, adjustment, service, cleaning, or maintenance could result in property damage, severe injury, or death.
Read and understand the installation, operating and maintenance instructions thoroughly before installing, servicing, or operating this equipment.
EN
MN-35948
CTP Combitherm
DANGER
This manual covers the following CTP series models:
Boiler-Free Models Steam Generator Models
6-10E, 6-10G
10-10E, 10-10G
7-20E, 7-20G 10-20E, 10-20G 20-10E, 20-10G 20-20E, 20-20G
Please post the following instructions in a prominent location in the event the user smells gas.
6-10EB
10-10EB
7-20EB 10-20EB 20-10EB 20-20EB
Before starting the appliance, make certain you do not detect the odor ofgas.
If you smell gas:
• Shut o the gas supply immediately.
• Do not attempt to light any appliance.
• Do not touch any electrical elements.
• Extinguish any open flame.
• Evacuate the area.
• Use a telephone outside the property and immediately contact your gas supplier.
• If unable to contact your as supplier, contact the fire department.
2 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
Enjoy your Alto-Shaam Combi Oven!
The combi oven combines a steam and convection oven into one versatile unit and can serve a variety of cooking functions. Alto-Shaam’s combi ovens allow chefs to control humidity and temperature separately, with powerful results. The same oven can be used to dehydrate vegetables, roast pork, steam rice, smoke brisket and bake loaves of bread.
The PROtouch™ recipe management system with one-touch cooking provides complete control over the oven, allowing chefs and foodservice employees to select pre-programmed recipes for
Before Use
If this is the first time this oven is being used, or if the oven has just been removed from storage, follow these steps for cleaning:
1. Remove all packing material from the oven,
2. Remove and wash any detachable items such as wire shelves, side racks, pans, and drip trays with hot, soapy water. Dry with a clean, damp lint-free cloth.
3. Remove all visible grease or oil from the oven.
4. Clean the interior and exterior of the oven with a mild soap and water solution. Apply the solution with a clean, damp cloth. Do not use commercial or household cleaners that contain ammonia. Wipe with a clean, damp cloth to remove all detergent residue. Dry with a clean, lint-free cloth.
CTP Combitherm
maximum consistency. To store and secure important information, a HACCP data system pairs up with an onboard USB port, so settings can be downloaded and saved for the future.
When it’s time to clean up, Alto-Shaam’s CombiClean Plus™ automated cleaning system saves labor previously spent scrubbing the oven cavity. On the oven’s exterior, a PROrinse™ retractable hose gives you spray-washing power without opening the oven door.
5. Clean the oven glass with glass cleaner or distilled vinegar. Re-install the side racks and wire shelves – position shelves with the curved end up and toward the rear of the oven.
When cleaning is complete, the oven must acclimate to room temperature in the environment where it is placed. Twenty four (24) hours is recommended.
The oven is now ready for operation.
EXTEND YOUR ORIGINAL MANUFACTURER’S WARRANTY
Register online today at www.alto-shaam.com/warranty
Register your Alto-Shaam appliance online, and you will automatically be entered into a monthly drawing to win an additional year extended warranty!
Registering your equipment ensures prompt service in the event of a warranty claim. You will also receive direct notifications of soware updates and additional product information.
Your personal information will not be shared with any other company.
ALTO-SHAAM 24/7 EMERGENCY REPAIR SERVICE
Call 800-558-8744 to reach our twenty-four hour emergency service call center
for immediate access to local authorized service agencies outside standard business hours. The emergency service access is provided exclusively for Alto-Shaam equipment and is available throughout the United States through Alto-Shaam’s toll free number.
Emergency service access is available seven days a week, including holidays.
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 3
4 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
CTP Combitherm
Introduction ................................ 3
Table of Contents .................................5
Safety Procedures ................................6
Labels ...........................................9
Operation ......................................16
How To Turn On the Oven ...................................16
How To Start a Manual Calibration ...........................16
How To Calibrate theTouch Screen ..........................16
How To Turn O the Oven ...................................16
Control Panel Identification .................................17
Home Screen ............................................17
Utility Screen ............................................17
Upload/Download Screen ................................17
Setting Screen 1 .........................................18
Setting Screen 2 .........................................18
Preventative Maintenance Screen .........................19
Preventative Maintenance - Editing .......................19
Soware Updates ..........................................20
Cooking Screen Identification ............................21
Auxiliary Functions and Features ............................22
Power Settings ..........................................22
Multiple Fan Speeds .....................................22
Multi-Shelf Timer ........................................22
Preheat Features ........................................23
Cool Down Feature ......................................23
Humidity Control Feature ................................24
Rapid Cool ..............................................24
Rest .....................................................24
Door ....................................................24
Factory Default Settings .....................................25
Cooking Modes - Steam .....................................26
Steam Mode Operating Tips .................................27
Cooking Modes - Combination ..............................28
Combination Mode Operating Tips ..........................29
Cooking Modes - Convection ................................30
Convection Mode Operating Tips ............................31
Cooking Modes - Retherm ...................................32
Retherm Mode Operating Tips ...............................33
Cooking Modes - Dehydration ...............................34
Dehydration Mode Operating Tips ...........................35
Cooking Modes - Delta-T Core Temperature ..................36
CombiSmoke® Procedures ..................................37
Recipe Programming .......................................39
Using Programmed Recipes ..............................40
To Cook with Preprogrammed Recipes ....................40
Editing Programmed Recipes .............................41
Organizing Programmed Recipes .........................42
HACCP Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
HACCP Access and Download ...............................45
Options ........................................46
CombiHood PLUS™ Ventless Hood ..........................46
How To Use the Combilatch™ Door Interlock .................47
Special Conditions for Units Installed in the City of New York ..48
Connecting the Optional Grease Collection System ...........49
Connecting the Optional Liquid Cleaner. . . . . . . . . . . . . . . . . . . . . .50
Recipe Guidelines ...............................51
Bakery Items ...............................................51
Convenience Product Items .................................53
Fish & Seafood Items .......................................54
Meat Recipes ...............................................55
Miscellaneous Recipes ......................................57
Poultry Recipes .............................................58
Vegetable Recipes ..........................................60
Cleaning and Preventative Maintenance ............62
CombiClean® Cleaning Agents ...............................62
Preventive Maintenance ....................................63
Weekly Maintenance ........................................64
Daily Inspection ............................................65
Weekly Inspection ..........................................66
Monthly Inspection .........................................67
Yearly Inspection ...........................................68
Protecting Stainless Steel Sufaces ...........................71
Cleaning Agents ............................................71
Cleaning Materials ..........................................71
Daily Cleaning of the Over ...................................72
Probe and Probe Prong Cleaning ............................72
Roll-In Cart/Food Trolley Cleaning ...........................72
CT PROtouch™ with CombiClean® ...........................73
CT PROtouch™ with Automatic Liquid Cleaning ...............74
Troubleshooting .................................75
Error Codes ................................................75
Touch Motor Control Error Codes ............................81
Limited Warranty ................................83
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 5
CTP Combitherm
• The appliance is intended to cook, hold or process foods
Knowledge of proper procedures is essential to the
for the purpose of human consumption. No other use for this appliance is authorized and is therefore considered dangerous. The appliance must not be used to cook food containing  ammable materials (such as food with alcohol). Substances with a low  ash point can ignite spontaneously and cause a  re.
• The appliance is intended for use in commercial establishments where all operators are familiar with the purpose, limitations, and associated hazards of this appliance. Operating instructions and warnings must be read and understood by all operators and users. Alto-Shaam recommends regular sta training to avoid the risk of accident or damage to the appliance. Operators must also receive regular safety instructions.
• Any troubleshooting guides, component views, and partslists included in this manual are for general reference only and are intended for use by quali ed and trained technicians.
• This manual should be considered a permanent part of this appliance. This manual and all supplied instructions, diagrams, schematics, parts lists, notices, and labels must remain with the appliance if the item is sold or moved to another location.
safe operation of electrically and/or gas energized equipment. The following signal words and symbols may be used throughout this manual.
DANGER
Indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
NOTICE: Indicates information considered important,
but not hazard-related (e.g., messages relating to property damage).
NOTICE: For equipment delivered for use in any
location regulated by the following directive: 2012/95/EC WEEE
Do not dispose of electrical or electronic
equipment with other municipal waste.
6 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
CTP Combitherm
• To prevent serious injury, death or property damage,
• If the gas appliance is installed under an exhaust
appliance is in use to avoid the build up of combustion
vents. Thisarea is hot and could be a potential ignition
suddentemperature change can damage the appliance
WARNING
the appliance should be inspected and serviced at least every twelve (12) months by an authorized service partner or trained technician.
• Only allow an authorized service partner or trained technician to service or to repair the appliance. Installation or repairs that are not performed by an authorized service partner or trained technician, or the use of non-factory authorized parts will void the warranty and relieve Alto-Shaam of all liability.
• When working on this appliance, observe precautions in the literature, on tags, on labels attached to or shipped with the appliance and other safety precautions that may apply.
• If the appliance is installed on casters freedom of movement of the appliance must be restricted so that utility connections (including gas, water, and electricity) cannot be damaged when the appliance is moved. If the appliance is moved, ensure that all utility connections are properly disconnected. If the appliance is returned to its original position, ensure that retention devices and utility connections are properly connected.
• Only use the appliance when it is stationary. Mobile appliance racks, mobile plate racks, transport trolleys, andappliances on casters can tip over when being moved over an uneven  oor or threshold and cause serious injury.
• Always apply caster brakes on mobile appliances or accessories when these are not being moved. These items could move or roll on uneven  oors and cause property damage or serious injury.
• Be extremely careful when moving appliances because the food trays may contain hot  uids that may spill, causing serious injury.
• Always open the appliance door very slowly. Escaping hot vapors or steam can cause serious injury or death.
hood, the hood must be switched On when the
gases. Failure to do so may result in serious injury, death or property damage.
• Accumulations on the main burners of gas appliances can result in  ring out of normal sequence. This delayed ignition creates an alarmingly loud sound. If your appliance makes an especially loud noise when starting up, shut down the appliance and call a quali ed and trained service technician.
• NEVER place objects near the appliance exhaust
source for a  re.
• Do not allow objects to block or obstruct the area below the appliance base. This may result in  re, damage to the equipment or serious injury.
• Do not use the attached hand-held hose to sprayanything other than the interior of the appliancecompartment.
• Do not use the attached hand-held hose on the surface of a hot cooking compartment. The
interior. Allow the appliance to cool to a minimum of 150°F(66°C). Failure to observe this precaution can void the warranty.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision concerning use of the appliance by person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 7
CTP Combitherm
CAUTION
CAUTION
WARNING
WARNING
WARNING
WARNING
To prevent serious personal injury, death, or property damage:
Do not steam clean, hose down or flood the interior or exterior with water or liquid solution of any kind. Do not use water jet toclean. Failure to observe this precaution will void the warranty.
To prevent SERIOUS PERSONAL INJURY or PROPERTY DAMAGE:
DO NOT handle pans containing liquid or semiliquid products positioned above the eye level of the operator. Such products may scald and cause serious injury.
DO NOT obstruct or block exhaust flues or attach any flue extension that may impede proper burner operation, restrict the exhaust fumes and cause negative backdra or the appliance to shut down. Failure to do so may result in serious injury or death.
To prevent serious personal injury, death, or property damage:
The appliance must be cleaned thoroughly to avoid deposits of grease and or food residues inside the appliance that may catch fire. If fat deposits and/or food waste inside the appliance ignite, shut down the appliance immediately and keep the appliance door closed to extinguish the fire. If further extinguishing is required, disconnect the appliance from the main power and use a fire extinguisher (do not use water to extinguish a grease fire!). Failure to clean the appliance properly invalidates the warranty and relieves Alto-Shaam of all liability.
To prevent personal injury or
propertydamage:
Always use hand protection when
operating this appliance to avoid burns. Metal parts of this equipment become extremely hot when in operation.
NOTICE: Automatic steam venting is a standard safety
feature built into all Combitherm oven models. This feature vents all steam from the oven compartment immediately before cooking time expires or set probe temperature is reached.
Automatic steam venting does not function if the
oven door is opened before time expires or when the oven has been set to continuous operation.
8 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
To prevent INJURY or PROPERTY DAMAGE, make certain the area around the appliance is kept clear of combustible items.
NOTICE: Use authorized Combitherm oven cleaner only.
Unauthorized cleaning agents may discolor or harm interior surfaces of the oven. Read and understand label and material safety data sheet before using the oven cleaner.
Made in U.S.A.
LA-39123
WARNING / ADVERTENCIA / AVERTISSEMENT
Burn hazard. Always load liquids, or foods that can become liquid when heated, at an eye level where they can be seen.
Peligro de quemaduras. Siempre coloque líquidos, o alimentos que se puedan volver líquidos cuando se calientan, a nivel de los ojos donde se puedan ver.
Risque de brûlure. Toujours charger les liquides, ou les aliments qui deviennent liquides au chauffage, à hauteur des yeux où ils peuvent être vus.
LA-39155
WARNING
Hot surface
WARNING
Electric shock hazard
CTP Combitherm
WARNING
Burn hazard
Always load liquids, or foods that can become liquid when heated, at an eye level where they can be seen.
Every Alto-Shaam product is precision calibrated prior to release from the factory to ensure accurate temperature control.
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 9
CTP Combitherm
LA-36443-L1
LA-36443-L2
LA-36443-L3
LA-36443-L2/N
LA-36443-G
LA-36443-E
LA-38911
LA-38909
Line 1 supply terminal
Line 2 supply terminal
Line 3 supply terminal
Neutral
Ground terminal
LA-38910
Equipotential terminal
Drain water connection point.
Untreated, drinkable water connection point.
Treated, drinkable water connection point.
10 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
kg max. liter max. GN 1/1
31
kg
LA-39336
6-10 33 57 6
10-10 54 95 10
7-20 76 13 10-20 109190 20 20-10 109190 20 20-20 218380 40
CTP Combitherm
Capacities
4
LA-38940
Fire hazard
This unit is only for use with factory-supplied legs, casters, or base.
Read the installation manual.
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 11
CTP Combitherm
LA-39126
Warning
Steam. Open door carefully.
CombiTabs
Warning
Failure to follow cleaning instructions can cause injury or equipment damage. Clean oven only with Combitherm cleaner. Cleaner is caustic. Avoid contact with skin or eyes. Wear PPE. Read and understand the Combitherm cleaner safety data sheet and the operator’s manual before cleaning
12 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
LA-39149
CTP Combitherm
Warning
Electric Shock Hazard
Appliances with permanent electrical connection that are mounted on casters must be secured to building structure. Read installation instructions.
LA-39148
Warning
Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing the equipment.
Water and waste connection shall comply with the basic plumbing code of the Building Officials and Code Administrators International, Inc. (COCA) and the Food Service Sanitation Manual of the Food and Drug Administration (FDA).
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 13
CTP Combitherm
Warning
Fire Hazard
For use only on noncombustible surfaces. Maintain the correct clearances to combustibles.
Read the installation instructions.
City of New York Fire Department condition of acceptance number.
Notice
For trained personnel only: The installation manual and the wiring
diagram for this appliance can be found inside the oven attached to the opposite side of this panel.
XXX
14 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
WARNING/ADVERTENCIA/AVERTISSEMENT
Electric Shock Hazard
To reduce the risk of electric shock, do not remove or open cover. No user-serviceable parts inside. Refer servicing to qualified personnel. Qualified personnel: Disconnect power before servicing.
Peligro de descarga eléctrica
Para reducir el riesgo de descarga eléctrica, no retire ni abra la cubierta. No hay piezas en el interior a la que se les pueda realizar mantenimiento. Derive el mantenimiento a personal calificado. Personal calificado: Desconecte la energía antes de realizar mantenimiento.
Danger de décharge électrique
Pour réduire le risque de décharge électrique, ne par ouvrir ni retirer le capot. Ne contient pas de pièces réparables par l’utilisateur. Confier les réparations à du personnel qualifié. Personnel qualifié : Sectionnez l’alimentation avant toute intervention.
LA-38950
CTP Combitherm
Warning
Electric shock hazard.
To reduce the risk of electric shock, do not remove or
open cover. No user-serviceable parts inside. Refer servicing to qualified personnel.
Qualified personnel: Disconnect power before servicing.
Use ______AWG for supply connecons.
Use only copper wires suitable for temperatures ≥ 90°C.
Do not connect to a circuit operang at more than 150 VAC to ground.
For use on individual branch circuits only.
Use AWG ______ para las conexiones de suministro. Use solo cables de cobre aptos para temperaturas mayores que 90 °C. No conecte a un circuito que funcione a más de 150 V CA a erra. Para su uso en circuitos derivados individuales solamente.
Uliser du calibre ______AWG pour les raccordements électriques. Uliser exclusivement des conducteurs en cuivre qui conviennent à des
températures ≥ 90 °C. Ne pas raccorder à un circuit fonconnant sous plus de
150 VCA par rapport à la terre. Uliser exclusivement sur des circuits de dérivaon propres.
AWG 90°C
LA-38852
NOTICE: Use only factory-supplied casters when needed. When
this appliance includes casters, the following must also be installed:
a connector complying with ANSI Z21.69 / CSA 6.16;
a quick-disconnect device complying with ANSI Z21.41 / CSA 6.9;
a restraining device to guard against transmission of strain to the
connector as specified in the manual.
AVISO: Solo use ruedas proporcionadas de fábrica cuando sea
necesario. Si este equipo incluye ruedas, también se debe instalar lo siguiente:
• un conector que cumpla con las normas ANSI Z21.69 y CSA 6.16;
• un dispositivo de desconexión rápida que cumpla con las normas ANSI Z21.41 y CSA 6.9;
• un dispositivo de sujeción para proteger contra la transmisión de tensión al conector como se especifica en el manual.
Use ______AWG for supply connections.
Do not connect to a circuit operating at more than 150 VAC to ground. For use on individual branch circuits only.Use only copper wires suitable for temperatures ≥ 90°C.
NOTICE: Use only factory-supplied casters when needed. When this appliance includes casters, the following must also be installed:
• a connector complying with ANSI Z21.69 / CSA 6.16;
• a quick-disconnect device complying with ANSI Z21.41 / CSA 6.9;
• a restraining device to guard against transmission of strain to the connector as specified in the manual.
AVIS : S’il y a lieu, utiliser uniquement les roulettes fournies par
le fabricant. Si cet appareil comporte des roulettes, les articles suivants doivent également être installés :
• un connecteur conforme à ANSI Z21.69 / CSA 6.16;
• un raccord découpleur rapide conforme à ANSI Z21.41 / CSA 6.9;
• un moyen de retenue pour empêcher la transmission de la contrainte au connecteur comme indiqué dans le manuel.
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 15
LA-25784
CTP Combitherm
How to Turn On the Oven
Prerequisites
1. Turn on the exhaust hood.
2. Make sure that the water supply to the oven is turned on.
3. Make sure that the electrical power supply to the oven is turned on.
4. For gas ovens, make sure the gas supply valve is in the open position.
Steps
1. Press the ON/OFF button .
The ON/OFF indicator glows green and the loading screen a displays while the controller soware loads. When the soware is 100% loaded, the home screen b displays.
NOTE: If the oven has a steam generator, the steam generator fills with water and the oven heats the water to an initial temperature of 188°F (77°C).
How to Start a Manual Calibration
1. Make sure the oven is o.
2. Press and hold the ON/OFF button for eight (8) seconds. The ON/OFF indicator glows red and the calibration prompt c displays.
The prompt moves from the center to all four corners of the screen. This sequence repeats three (3) times. Then the calibration screen d displays.
NOTE: The first time the oven is turned on, or if the oven loses power during startup, the touchscreen calibration prompt c displays at the end of the next startup.
NOTE: Touch the check mark icon to start the calibration immediately. Touch the cancel icon to cancel the calibration.
DANGER
Before starting the appliance, make certain you do not detect the odor ofgas. If you smell gas:
• Shut o the gas supply immediately.
• Do not attempt to light any appliance.
• Do not touch any electrical elements.
• Extinguish any open flame.
• Evacuate the area.
• Use a telephone outside the property and immediately contact your gas supplier.
• If unable to contact your as supplier, contact the fire department.
CAUTION
Accumulations on the main burners of gas appliances can result in firing out of normal sequence. This delayed ignition creates an alarmingly loud sound. If your appliance makes an especially loud noise when starting up, shut down the appliance and call a qualified and trained service technician.
1
2
How to Calibrate the Touchscreen
1. Touch the target icon (+) each time it appears on screen. The icon appears in all four corners, then the center of the screen.
NOTE: If the controller soware has not been updated to the current version (11/16 update), the calibration stops when this step is complete. Download the current controller soware from the Alto-Shaam website and install it.
2. The verification screen e displays. Touch all five target icons . The icons change to green boxes when they are touched.
NOTE: The calibration screen and verification screen both display a 30-second countdown. If you do not touch all five icons before the countdown is complete, the controller stops the calibration. If you do not see the countdown, download the current controller soware from the Alto-Shaam website and install it.
How to Turn O the Oven
1. Press and hold the ON/OFF button for five to ten (5-10) seconds.
16 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
3
4
5
Control Panel Identi cation
Control Panel Identification
Professional
Cooking Mode
Cookbook with
Saved Recipes
CleaningSleep Mode
Information
Call outs
CTP Combitherm
Utility Screen
So ware Version
Utilities
Upload/Download
Settings
Download Recipes from
USB stick — overwrites
any existing recipes
Add all recipes on a
USB stick to the list of
recipes on the oven
leaving all other recipes
on the oven untouched
*Download new so ware from a
USBstick
Upload odometer
info to USB stick
Return to
previous screen
Upload/Download Screen
(password protected)
Upload all recipes from control to a USB stick
Upload HACCP info to USB stick
Upload audit trail info to USB stick
Service Mode
Return to
previous screen
Return to
home screen
* The PROtouch control plays an
important part in our continuous improvement process. New features and abilities can be loaded to your oven as they become available. So ware for your oven can be accessed from the Alto-Shaam website, under the Downloads tab.
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 17
CTP Combitherm
Control Panel Identi cation
recipe display with text, and recipes are not
Settings Screen 1
Fahrenheit /Celsius
Keep last user setting
Handle LED on
Recipe display
names on
Unlock recipes
Beeper volume
& alarm clips
Screen brightness
Return to
previous screen
Screen 1 of 2
Settings Screen 2
Use factory default settings
Handle LED o
Recipe display names o
Lock recipes
Advance to next setting screen
When a setting has been selected, the graphic will be vibrant in color while the alternate choice will appear faded and gray. In the illustration above, Fahrenheit, factory default setting, handle LED on,
locked have been chosen.
NOTE: A password is required to lock
and unlock the recipes. Simply call an Alto-Shaam Culinary Chef for assistance.
Language Choices
Date/Time
Future Feature
(not yet available)
Calibrate product probe
Preventative
Maintenance Actions
Run diagnostics
Force Boiler Flush
Return to previous
setting screen
Return to
utility screen
Language choices available: English, French, German, Korean, Mandarin, Russian, or Spanish.
Time format available:
12-hour clock
24-hour clock
Di erent date formats available:
YYYY/MM/DD
MM/DD/YYYY
DD/MM/YYYY
Screen 2 of 2
18 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
CTP Combitherm
Control Panel Identi cation
Preventative Maintenance Screen
Cleaning Timer
Gasket Inspection
Ventless Hood
Filter Replacement
Return to
previous screen
Water Filter Replacement
Boiler De-Liming
Utilities
Return to
home screen
Preventative Maintenance - Editing
Press item to edit
Return to
previous screen
Increase or decrease alarm setting to match your preferred timelines.
A er the task has been completed, set elapsed time to 0 to begin countdown process again.
Utilities
Return to
home screen
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 19
CTP Combitherm
So ware Updates
The PROtouch controller plays an important part in our continuous improvement process. New features and abilities
Soware Updates
can be loaded to your oven as they become available. So ware for your oven can be accessed from the Alto-Shaam website, under the Resource Library Tab, then So ware Center. http://www.alto-shaam.com/en/so ware-download-center
Use a USB stick to copy the PROtouch so ware from the website to the USB stick.
So ware Upload Screen
Press the ON button to power the oven on.
Touch the utilities icon.
Touch the download icon.
Touch the download new so ware icon.
Full oven update:
IB, CB, and OB
Update the CB
(control board) only
Update the OB
(option board) only
Update the IB
(interface board) only
Most so ware updates will require the full oven update as shown below. Additional options are available in the event a special need arises. Call our Service Department for assistance with these special circumstances.
Remove the cover of the USB port on the oven.
Insert the USB stick. If the USB stick is not recognized by the Combitherm, a question mark will appear on screen. Try again with another  ash drive device or call
Return to
previous screen
Alto-Shaam Service.
When the data has made a successful transfer to the USB drive, the screen will change.
Touch the green check mark icon to complete the process.
Remove the USB stick and replace the cover on the USB port on the oven.
NOTICE: A er the so ware update has
been completed, the oven may automatically initiate a shut down and reboot sequence if required.
20 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
Cooking Screen Identi cation
Cooking Screen Identification
CTP Combitherm
Steam
Mode
Oven Temperature
Cook Time
Probe Temperature
Preheat
Start
Return to
previous screen
Combi
Mode
Return to
Home Page
Convection
Recipe
Mode
Retherm
Mode
Cook Time is displayed as hours : minutes : seconds
Cool Down
UtilitiesWrite
Chosen
Cooking
Mode
Return to
previous screen
Chosen
Entry Field
Allowable Temperature Range
Entry Keypad
Enter
NOTE: When a cooking mode has been selected, it will appear darker
blue. When the cooking mode is calling for heat, it will appear red. When the cooking mode is calling for moisture, it will appear light blue. In the illustration above, Combi Mode has been chosen and is calling for heat. Also, the PROpower™ level has been chosen, and the fan speed has been set at 100%.
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 21
CTP Combitherm
Auxiliary Functions and Features
Power Settings
Auxiliary Functions and Features
Two power levels: reduced power to manage kitchen power peaks, and eco power for optimal oven e ciency.
A third choice is optional on electric models, but standard on gas models. PROpower™ is an accelerated turbo power for an instant boost of heat or quick heat recovery [patent pending].
NOTE: Reduced power will result in longer cooking
times and PROpower will decrease your cooking time by several minutes.
Multiple Fan Speeds
The PROtouch™ control includes  ve di erent fan speeds. The reduced fan speed function is useful for  ow-sensitive products such as sou és and meringues, or any products a ected by a high velocity of air movement.
NOTE: Fan speed choices are based upon the power
level you have chosen.
PROpower
Eco Power
Reduced Power
Return to previous screen to set the remaining auxiliary functions for full functionality
Power level icon appears during operation
Fan speed choices
Reduced Power Level
Eco Power Level
PROpower™ Power Level
Multi-Shelf Timer
The multi-shelf timer allows the operator to program alarm times for the oven shelves. This can be one common time for corresponding oven shelves or by food item that is cooking. The multi-shelf timer can be edited when in a recipe mode.
Touch shelf number to
enter a recipe identifier
(text or number)
previous screen
22 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
Return to
Chosen
Cooking
Mode
Chosen
Temperature
Timer ready, touch green arrow to begin
Time value, touch this area to change the time value
Timer countdown in process, Touch red square to stop
Auxiliary Functions and Features
Preheat Feature
The oven should be preheated before most cooking functions. When cooking full loads, use a temperature 50°F (10°C) greater than the cook temperature in order to recover from heat loss when the door is opened to add food to the oven. For items that use the Steam mode, it is necessary to use a preheat temperature lower than the cook temperature in order to create the proper amount ofsteam.
CTP Combitherm
Press the On button to power oven on.
Touch the Preheat icon. Type in desired temperature.
Touch the green Check Mark icon to startpreheating.
Cool Down Feature
The cool-down feature provides the operator with the ability to lower the temperature of the oven compartment at an accelerated pace. This function is useful when it is necessary to immediately change from a high temperature cooking function to a lower temperature function or to the steam program. This function is also useful to help cool the oven compartment in preparation for cleaning.
TIP: Always allow the oven walls to cool to a minimum
of 140°F (60°C) before spraying the compartment with oven cleaner.
Preheat
Return to previous
screen
Cool Down
Open the oven door.
Touch the Cool Down icon.
Type in desired temperature.
Touch the green Check Mark icon to beginthe Cool Down process.
The target oven temperature chosen will appear just above the red Stop button.
The current oven temperature will appear at the top of the screen.
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 23
Touch to
Stop
CTP Combitherm
Auxiliary Functions and Features
Humidity Control Feature
The humidity control feature is an automatic function designed to regulate humidity to provide additional color to food as needed. This feature is particularly useful for adding color to high moisture products such as chicken and other poultry, or for additional browning of full loads and other moist products. In addition, this feature may be used to add texture to fried items such as french fries or breaded chicken. Humidity control can be used in any cooking mode and can be programmed into a cooking procedure.
Touch the nearest 10% increment on the le side of the screen, and then adjust up or down using the + or – icons.
0% humidity is the driest cooking environment available. The percentage level chosen will appear on the icon. In the illustration at right, 72% is shown.
Humidity level choices
in increments of 10%
Return to
previous screen
Adjust humidity level up or down in increments of 1%
Touch the check mark to approve the value entered.
Rapid Cool (available on boiler-free models only)
This function, when used with a program, rapidly removes heat from the oven cavity. Swi ly move from a high cooking temperature to a lower temperature without overcooking your food.
Rest
This step allows you to pause the oven during a program. The rest step is ideal for cold smoking or automatic cleaning. Infuse your food with smoke  avor a er the actual smoking step has stopped.
Door
The door function allows the user to program a reminder—in the form of an animated door opening and closing—that it is time to open the door. This reminder may be programmed at the end of a programmed segment or at the end of the program.
Return to
previous screen
Rapid Cool
(boiler-free models)
Chosen Humidity Level % shown
Door
Rest
24 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
CT PROformance™ Factory Default Settings
Cooking Mode Oven Temperature Core Temperature Cooking Time
CTP Combitherm
Steam
Combination Steam
Convection
Retherm
212°F
(100°C)
350°F
(175C)
350°F
(175C)
275°F
(135°C)
160°F
(70°C)
160°F
(70°C)
160°F
(70°C)
160°F
(70°C)
25 minutes
70 minutes
30 minutes
5 minutes
MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual • 25
CTP Combitherm
CAUTION HOT
Steam Mode
The Steam mode provides the operator with the ability to steam, poach, or blanch. This mode will automaticallysteam at the boiling point of water; quick-steam above the boiling point for faster cooking results; or low temperature steam, below the boiling point, for more delicate products such as pâté, mousse, seafood, orcustard.
Press the On button to power oven on.
Touch the Professional Cooking mode icon.
Touch the Steam mode icon.
Touch the Start icon to steam at the displayedsettings.
To Change the Displayed Settings:
Touch the area to the right of the temperatureicon.
Type in desired temperature.
Touch the green Check Mark icon to confirmchange.
To Cook by Product Core Temperature:
Touch the area to the right of the probeicon.
Type in desired temperature.
Touch the green Check Mark icon to confirmchange.
Insert probe into product.
Set available auxiliary functions as desired, such as energy level, fan speed, multi-shelf timer, etc.
Touch the Start icon to begin cooking in the Steam mode.
• The cavity set-temperature will appear in the display.
• If cooking by probe, the actual internal product temperature will appear next to the probe icon during operation. To change the set value for core temperature, touch the temperature next to the probe icon and make changes as required.
When the cooking time has expired or the desired core temperature has been reached, an alarm will sound and handle light will flash several times indicating the end of the operating mode.
• Automatic Steaming 212°F (100°C)
• Quick Steaming 213°F to 250°F (101°C to 120°C)
• Low Temperature Steaming 85°F to 211°F (30°C to 99°C)
To Cook by Time:
Touch the area to the right of the timeicon.
Type in desired time or set continuous time by touching --:--.
Touch the green Check Mark icon to confirmchange.
26 • MN-35948 • Rev 16 • 10/18 • Combitherm® CT PROformance™ Series Operator’s Manual
Touch the red Stop icon to stop the buzzer or open the oven door.
To stop cooking program at any time, touch the red Stop icon.
Use caution when opening the oven door when the cooking chamber is hot to avoid possible burns.
Loading...
+ 58 hidden pages