• Setting items, operations, etc., may be modified or removed
without notice depending on the connected Alpine
Bluetooth compatible unit.
WARRANTY-EN
1-EN
Operating Instructions
WARNING
WARNING
This symbol means important instructions.
Failure to heed them can result in serious
injury or death.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed,
consult a physician immediately.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE
NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.
When drilling holes in the chassis for installation, take
precautions so as not to contact, damage or obstruct pipes, fuel
lines, tanks or electrical wiring. Failure to take such precautions
may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could
disable control of the vehicle and cause fire etc.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN
SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the manual to
prevent obstructions when driving. Cables or wiring that obstruct
or hang up on places such as the steering wheel, gear lever, brake
pedals, etc. can be extremely hazardous.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire,
electric shock or other injury.
MAKE THE CORRECT CONNECTIONS.
Failure to make the proper connections may result in fire or
product damage.
CAUTION
This symbol means important instructions.
Failure to heed them can result in injury or
material property damage.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
Be sure to use only the specified accessory parts. Use of other
than designated parts may damage this unit internally or may not
securely install the unit in place. This may cause parts to become
loose resulting in hazards or product failure.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE
OR DUST.
Avoid installing the unit in locations with high incidence of
moisture or dust. Moisture or dust that penetrates into this unit
may result in product failure.
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.
The wiring and installation of this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
where you purchased this product to have the work done.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the
seat rails) or sharp or pointed edges. This will prevent crimping
and damage to the wiring. If wiring passes through a hole in
metal, use a rubber grommet to prevent the wire’s insulation from
being cut by the metal edge of the hole.
2-EN
Setup Before Using
How to connect to a Bluetooth
compatible device (Pairing)
About Bluetooth
Bluetooth is a short distance wireless technology to connect a
mobile phone or personal computer. This allows you to
enable a hands-free call or transmit data between Bluetooth
compatible devices.
• Depending on the Bluetooth version, a Bluetooth compatible device may not be able to communicate with this
adapter.
• Proper function of this adapter with all Bluetooth
compatible devices is not guaranteed.
• Depending on the surroundings, Bluetooth wireless
connection may be unstable.
• When you place a call, or perform setup operations, be
sure to stop your car in a safe place.
• For details on the control (selection, enter, cancel) from the
connected unit, refer to the Owner’s Manual of the
respective unit.
• Depending on the connected Bluetooth compatible
device(s), the function may differ. Also refer to the Owner’s
Manual of the connected device(s).
Before Using Hands-Free Phone/
Audio Function
Before using the hands-free phone/audio function, the
following settings need to be made.
1
Be sure to set “INT MUTE” (in the setup
function of the connected head unit or Digital
Media receiver) to OFF.
• Before making sound interruption on the Bluetooth
compatible device, make sure that INT MUTE is set to
OFF. (Initial setting on the unit is OFF.)
2
Set “Bluetooth IN” or “Bluetooth” to
ADAPTER*. (Refer to the Owner’s Manual of
the connected units.)
3
Turn the ignition key off (ACC OFF) and on
again (ACC ON).
• Before using a hands-free phone, it must be paired with the
adapter. Refer to “Bluetooth SETUP” (pages 4-5).
* If “Bluetooth IN” or “Bluetooth” is set to OFF once, the
communication to the adapter is canceled. To resume
communication: reset to ADAPTER, set the ignition key
from ACC to OFF once, and then to ON again.
* When a Bluetooth compatible device is not used, set
“Bluetooth IN” or “Bluetooth” to OFF, and remove the
adapter. If Bluetooth connection of the adapter is
maintained, connection (pairing) error to the adapter may
occur depending on the mobile phone, and result in
malfunction.
For details on the control from a Bluetooth compatible
device, refer to the Owner’s Manual of the Bluetooth
compatible device.
1
Set a Bluetooth connection from a Bluetooth
compatible device.
2
The PIN code (“0000”) is displayed on the
connected unit.
• The PIN code is fixed as “0000.”
3
Input the PIN code (“0000”) in a Bluetooth
compatible device.
4
If the connected unit is successfully
connected to a Bluetooth compatible device,
a paired device name and a registered
number (No. 1 to 4 or guest mode) are
displayed on the unit, and then the unit
returns to normal mode.
• Set “Setting the Search Mode” (page 5) to ON to enable
the KCE-300BT to recognize a mobile phone. For mobile
phone passkey (passcode) input operation, refer to the
mobile’s Owner’s Manual. Additionally, the mobile phone
can be searched directly from an AV head unit. Refer to
“Registering the Bluetooth Device (AV Head Unit only)”
(page 5).
3-EN
Bluetooth SETUP
[ The explanations in this Owner’s Manual mainly
describe the following operations from the AV head
unit.
Bluetooth Setup Operation
The following steps 1 to 5 are common to the various
Bluetooth functions. For details, refer to each individual
function.
• When calling, or selecting the Tel. mode or Bluetooth
Audio source, Bluetooth Setup operation cannot be
performed.
• Refer to the Owner’s Manual of the CD Head unit, AV
Head Unit or Digital Media Receiver, and set “Bluetooth
IN” or “Bluetooth” to ADAPTER, and then perform
Bluetooth SETUP operation.
1
Touch [SETUP] on the main source screen.
The SETUP selection screen is displayed.
2
Touch [SOURCE] or [ ] of SOURCE.
The SOURCE SETUP screen is displayed.
3
Touch [ ] of BLUETOOTH or BLUETOOTH
SETUP.
The Bluetooth setup is displayed.
4
Touch [;] / [:] , [ON] / [OFF] or [ ] of the
desired item to change its setting.
Select one of 5 connected Bluetooth compatible devices that
you previously registered (one registered by guest mode*).
Setting item: PAIRED DEVICES
1
Select a Bluetooth compatible device to use
(change connection) from the PAIRED
DEVICE list.
2
Touch [:].
• If the connection is successfully changed, “CONNECTED/
(Device name)” is displayed for 2 seconds, and then the
display returns to the SETUP screen.
• If you input the wrong passcode or communications fail,
“FAILED” is displayed.
• If you want to connect another Bluetooth compatible
device, after disconnecting the current Bluetooth compatible device, connect the Bluetooth compatible device you
want to change to.
The PIN code is fixed as “0000.”
* Guest mode:
Use this mode for a temporary pairing. Registration (in
guest mode) is canceled once the ignition key goes from
ACC to off.
Controlling from a CD Head Unit / Digital Media
Receiver:
1 Turn the Rotary encoder or the Center jog dial to select
a Bluetooth compatible device you want to use (you
want to change connection).
2 Press ENT. (Depending on the connected units, this
operation may not be necessary.)
5
Touch [RETURN] to return to the previous
screen.
Controlling from a CD Head Unit / Digital Media
Receiver:
1 Press and hold SETUP for at least 2 seconds.
2 Turn the Rotary encoder or the Center jog dial to select
Bluetooth or Bluetooth IN, and press ENT.
3 Turn the Rotary encoder or the Center jog dial to select
the desired setting items and press ENT.
Setting items:
Bluetooth IN ↔ Paired Device* ↔ Visible Mode*
AUTO Answer
* When “Bluetooth IN” or “Bluetooth” is set to
ADAPTER, the above items are displayed.
4 Turn the Rotary encoder or the Center jog dial to change
the settings.
5 Press ENT. (Depending on the connected units, this
operation may not be necessary.)
6 Press and hold ESC (or SETUP) or BACK for at least 2
seconds.
The SETUP mode is canceled.
* ↔
Clear Device
*
4-EN
↔
Loading...
+ 10 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.