Alinco DJ X7T User manual
Rhein Tech Laboratories, Inc. Client: Alinco, Inc.
360 Herndon Parkway Model: DJ-X7T
Suite 1400 Standards: FCC 15.121
Herndon, VA 20170 & IC RSS-215
http://www.rheintech.com
Report #: 2005073
APPENDIX H: MANUAL
Please see the following pages.
Page 23 of 37
DJ-X7T/E
WIDE BAND COMMUNICATION RECEIVER
TONE
BANK
SHIFT
MW
PRI
10M/1M
PWR
BAND
V/P/M
SCAN
DJ-X7
WIDE BAND
COMMUNICATION RECEIVER
Instruction Manual
ALINCO, INC.
2
NOTICE / Compliance Information Statement
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the
device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Tested to Comply
With FCC Standards
FOR HOME OR OFFICE USE
Information in this document is subject to change without notice or obligation. All brand names and trademarks are the property of their
respective owners. Alinco cannot be liable for pictorial or typographical inaccuracies. Some parts, options, and/or accessories are
unavailable in certain areas. Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the device.
Wide Band Communication Receiver DJ-X7T
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Conformity Information
In case the device you have purchased is marked with a CE symbol, a copy of the relative conformity certificate or document can be
reviewed at http://www.alinco.com/usa.html. This device is authorized for use in all EU and EFTA member states.
MANUFACTURER: ALINCO, INC. Shin Dai Building 9F, 1-2-6, Dojimahama, Kita-ku, Osaka, 530-0004, Japan
Copyright © 2005 All rights reserved. No part of this document may be reproduced, copied, translated, or transcribed in any form or by any
means without the prior written permission of Alinco, Inc., Osaka, Japan.
English Edition Printed in Japan.
3
Precautions ......................................................................5
Precautionary Statement ..........................................................5
Precautionary Statement - External Power Supply...................5
Request and Agreement ..........................................................5
Chapter 1 Features ..........................................................6
1.1 Standard Accessory List ....................................................6
Chapter 2 Accessories ....................................................7
2.1 Mounting Arrangement.......................................................7
■Installing & uninstalling antenna..................................7
■Installing & uninstalling battery ...................................7
■Precaution for preventing short-circuit of battery........8
■Receiving while charging with AC adapter .................9
■Low battery indicator...................................................9
Chapter 3 Names and Functions of Parts ....................10
3.1 External View ....................................................................10
■Top/Front panel .........................................................10
■Side panel .................................................................11
3.2 Key Operations.................................................................12
3.3 Icons and Indicators.........................................................13
Chapter 4 Basic Operations ..........................................14
4.1 Turning Power ON ............................................................14
4.2 Adjusting Volume Level....................................................14
4.3 Adjusting Squelch Level...................................................15
■Monitor function.........................................................15
■Mute function.............................................................16
4.4 Operating Modes .............................................................16
■Switching among modes...........................................16
4.5 Frequency Settings ..........................................................17
■VFO mode .................................................................17
■Preset mode ..............................................................18
■Memory mode ...........................................................19
4.6 Memory Mode ..................................................................19
■Memory types............................................................19
■Programming to memory channel .............................20
■Clearing memory channel .........................................21
■Programmable items to memory channels................21
Chapter 5 Advanced Operations ..................................22
5.1 Scanning Function............................................................22
■VFO scan...................................................................22
■Programmed scan.....................................................23
■Preset scan................................................................23
■Memory scan.............................................................23
5.2 Memory Skip Function......................................................24
5.3 Key-lock Function.............................................................25
5.4 Priority Monitoring Function..............................................25
5.5 Descrambling Function ....................................................25
5.6 Tone Squelch Function.....................................................26
5.7 Tone Scan Function..........................................................27
5.8 Shift Function....................................................................27
Chapter 6 Set Mode Configurations .............................28
6.1 Set Mode Menu List..........................................................28
6.2 Configuring Values/Parameters of Menu Items................28
6.3 Set Mode Configurations..................................................29
(1)Attenuator function setting.......................................29
(2)Antenna Type Switching setting ..............................29
(3)AM Bar-antenna setting ...........................................30
(4)Shortwave Bar-antenna setting................................30
(5)Illumination Lamp function setting ...........................30
(6)Scan Type Switching setting ...................................31
(7)Priority Monitoring function setting ..........................31
(8)Auto-Power-Off function setting...............................31
(9)Battery-save function setting ...................................32
(10)Key-touch Beep function setting ...........................32
(11)Bell (Pager) function setting ..................................32
(12)Monitor/Mute function setting ................................33
(13)Monitor-key Operation setting ...............................33
Table of Contents
4
(14)Write-protect function setting.................................34
(15)Modulation Type setting ........................................34
Chapter 7 Cable-clone and PC Connection .................35
7.1 Cable Connection.............................................................35
7.2 Operation for Receiving Data (on the Slave)....................35
7.3 Operation for Transferring Data (on the Master) ..............36
Chapter 8 Maintenance and Reference........................37
8.1 Troubleshooting................................................................37
8.2 Resetting ..........................................................................38
■Factory default value .................................................38
8.3 Optional Accessory List ...................................................38
8.4 Table of Available CTCSS Tones .....................................39
Chapter 9 Specifications ...............................................40
This manual uses the following icons to explain:
Caution
Items indicated with this icon mention precautions for use
and procedures which need to be followed. Otherwise,
person may be injured, or the receiver including
accessories may be damaged or not operate properly.
Items indicated with this icon mention precautions for
use and procedures which need to be followed.
Items indicated with this icon mention supplementary
and referential information.
Memo
NOTE
5
Precautions
Precautionary Statement
• Do not open the case nor touch the interior components.
Tampering can damage the receiver.
• Do not place the receiver in any place where it will be
subjected to direct sunlight, dust, or high temperatures.
• Keep the receiver away from TVs, tuners, or other equipment
if it interferes with reception.
• Ensure that the provided antenna is securely mounted.
• Turn the power OFF immediately if the receiver should emit
smoke or strange odors. Ensure that the receiver is safe, then
contact the nearest Alinco Service Center.
Precautionary Statement - External Power Supply
• Use a regulated 3.7V to 6.0V DC external power supply.
• Never use any external power supply which exceeds 6.5V.
Otherwise, this may cause the serious damage.
• To charge the battery or operate the receiver using AC power,
use the provided AC adapter (EDC-126 or EDC-128
depending on the version). Connect the adapter to the
receiver's DC-IN jack directly.
• When power is supplied from the cigarette socket of a car,
use the optionally available cigar-socket DC cable (EDH-32).
• Turn the receiver's power OFF when connecting or
disconnecting the cable of external power supply.
Request and Agreement
• This receiver is manufactured and shipped under strict quality
control. However, in some rare instances, if questionable or
doubtful points are found, please notify the store where you
purchased the receiver.
• Since this is a wide band communication receiver, its internal
oscillation can sometimes block a signal, or detect an internal
signal (sometimes referred to as a "birdie"). These symptoms are
not a malfunction.
• Specifications and information found in this document are
subject to change without notice.
• DJ-X7 is a wide band receiver and can be applied to
business use.
• DJ-X7 receives AM radio with the internal bar-antenna.
• DJ-X7 receives high frequency wave (shortwave) with the
internal bar-antenna.
• DJ-X7 receives FM radio with the provided earphone antenna.
• DJ-X7 features the Shift function.
• DJ-X7 features the Tone Squelch function, and it covers 39
CTCSS tones.
• DJ-X7 features the Cable-clone function.
• DJ-X7 features the PC Connection function*.
• DJ-X7 adopts Lithium ion rechargeable battery.
* The free editing software can be downloaded at our website
(http://www.alinco.com). The optional PC interface-cable
(ERW-4C) is required to interface your computer and the
DJ-X7. Please visit our website for more details before you
purchase the ERW-4C as some restrictions may apply
depending on your computer conditions.
1.1 Standard Accessory List
Standard accessories may vary. Please contact your dealer for
details.
• A Li-Ion rechargeable battery pack*
DJ-X7T/E: EBP-58N (3.7V 600mAh)
• An AC adapter for both recharging battery and supplying
power** (6.0V 0.5A)
DJ-X7T: EDC-126 (120V)
DJ-X7E: EDC-128 (220V)
• An SMA whip antenna
DJ-X7T/E: EA-131
• A curl-cable earphone/antenna
DJ-X7T/E: EME-25
• An antenna cap
• An instruction manual
* Hereinafter referred to as battery or battery pack.
** Hereinafter referred to as AC adapter or adapter.
6
1
Features
Chapter 1 Features
7
2.1 Mounting Arrangement
■Installing & uninstalling antenna
●Installing antenna
1.Hold the antenna at the base.
2.Attach the antenna to the
antenna connector.
3.Turn the antenna clockwise
until it stops.
4.Ensure the antenna is securely
installed to the receiver.
●Uninstalling antenna
Turn the antenna counterclockwise.
Caution
When antenna connector conversion is necessary, be sure
to select a proper conversion connector or cable which
does not overburden the receiver. Otherwise, this may
cause the damage to the receiver and/or the antenna.
Installing an excessively high performance external
antenna may get worse of the receiving conditions.
■Installing & uninstalling battery
●Installing battery
1.Align the projections on the
battery with the grooves on
the receiver.
2.Push the battery in the direction
of the arrow.
3.Push down the latch of the
battery until it clicks.
●Uninstalling battery
1.Push the latch of the battery
upward.
2.Pull out the battery in the
direction of the arrow.
Latch
Latch
Projections
Grooves
NOTE
2
Accessories
Chapter 2 Accessories
Caution
• Do not modify, dismantle, incinerate, or immerse the
battery pack, as these practices can be dangerous.
• Do not short-circuit the terminals of the battery pack. This
may cause damage to the receiver. The short-circuit may
lead to overheating the battery, which causes burns.
• The battery pack should be stored in dry places where
the temperature range is between -20 to 45˚C (-4 to
113˚F). Leaving the battery pack exposed in high
humidity or outside the proper temperature range may
cause battery liquid leakage or rust on the metal portion.
• The battery pack is not charged when shipped. It
must be charged before use.
• The battery pack can be charged by plugging the AC
adapter to the DC-IN jack of the receiver after
mounting it to the DJ-X7.
• It takes up to 2 hours and 30 minutes (maximum) to
fully charge.
• Charging should be conducted within a temperature
range of 0 to 40˚C (32 to 104˚F). Otherwise, the
battery won't be charged properly.
• Be sure to remove the battery pack when the receiver
is not in use for a long period.
• Typically, the battery pack can be charged up to 500
times. However, it is considered consumed if the period
of use significantly drops despite the battery being
charged for the aforementioned charging time. When
this happens, replace the old battery with a new one.
• In the interests of environmental protection, do not
dispose of the battery pack improperly. Check with
your local solid waste officials for details on recycling
options or proper disposal in your area.
• It is not necessary to turn the power OFF of the
receiver while charging. However, noise may occur
during reception.
■Precaution for preventing short-circuit of battery
Be extra cautious when
carrying the battery pack; the
short-circuit will produce surge
current possibly resulting in
fire.
Put it in a non-conductive plastic bag, or wrap it
with a non-conductive material when you carry.
Protect it by
spreading a nonconductive sheet.
DON'T carry with any
type of metals. (e.g.
chains)
DON'T put it in bags
whose interior is
plated with metal.
DON'T wrap with a
metal plated cloth.
DON'T place it in the
proximity of metals or
conductors. (e.g.
nails, chains)
Terminals
NOTE
8
2
Accessories
9
2
Accessories
■Receiving while charging with AC adapter
●Charging battery
1.Install the battery pack to the
receiver.
2.Plug the AC adapter to the
DC-IN jack of the receiver.
3.Plug the power plug to an
outlet.
(EDC-128 has different shape.)
Regardless of whether the power ON or OFF of the receiver, it
will start charging.
When the receiver is OFF state, the low battery indicator shown
below blinks and the RX lamp illuminates during charge. Once
it is fully charged, the lamp will go off.
Caution
• Never charge batteries of other manufacturers. Never
plug the provided AC adapter to other devices, either.
• If you should short-circuit the terminals with metal objects
and the like, it may cause damage to both the receiver
and the battery.
• Be sure to connect the AC adapter after mounting the
battery pack to the receiver. Otherwise, the battery
won't be charged.
• Be sure to unplug the AC adapter when it is not in
use.
• The required charging time depends on the condition
of the battery pack.
• The battery won't be charged if the voltage from an
outlet is extremely low.
■Low battery indicator
• Battery consumption level may change depending on the
surrounding temperature or the conditions of use.
• Charge the battery when the indicator appears.
• This is not an indicator for battery life remaining.
Low battery indicator
Indicates the charge level is
low.
NOTE
AC adapter plug
Power plug
10
3
Names and Functions of Parts
3.1 External View
Chapter 3 Names and Functions of Parts
EAR
PUSH
VOL/SQL
SET
TONE
BANK
SHIFT
MW
PRI
10M/1M
PWR
BAND
V/P/M
SCAN
DJ-X7
WIDE BAND
COMMUNICATION RECEIVER
1
1
2
3
4
5
6
7
2
7
6
3
4
5
Earphone jack
Dial
RX lamp
Keypad
Speaker
Power key
LCD
■Top/Front panel
This is for plugging an earphone or an external
speaker (8Ω) with 2.5ø stereo plug.
Rotate this dial to change frequency and various
settings.
Press this dial to adjust the volume and squelch
levels.
Pressing it down while the icon appears
switches to the Set mode. (P.28)
It illuminates green while it receives signals or
the squelch opens.
Use this keypad to change mode and various
settings.
See on P.12 for more information.
A thin speaker is built in.
Holding this key for 1 second turns the power
ON/OFF of the receiver.
It displays frequency and other information.
See on P.13 for more information.
Item Description
11
3
Names and Functions of Parts
F
LOCK
MONI
SKST
8
9
10
11
■Side panel
8
9
10
11
Antenna
connector
Function key
(LOCK)
Monitor key
(ST/SK)
DC-IN jack
Install the included whip antenna or an external
antenna.
(Hereinafter referred to as [F] key.)
Use this key in combination with other keys to
access various functions of the receiver.
Holding this key for 1 second activates the Keylock function.
(Hereinafter referred to as [MONI] key.)
When this key is pressed, squelch opens so that
you may receive weaker signals better.
TSQ becomes deactivated also.
Pressing it down while the icon appears
changes tuning steps.
This is for plugging an external power supply.
Connect the included AC adapter or an optional
cigarette lighter cable to operate without
battery.
When you install the provided battery, you can
charge it by connecting the adapter or the
cable.
(Depending on the receiving frequency, noise
may occur when you use the receiver with the
cable.)
Item Description
12
3
Names and Functions of Parts
3.2 Key Operations
[F] key
Dial
V/P/M
SCAN
BAND
PWR
10M/1M
F
Dial
Switch among the
VFO/Preset/Memory mode (P.16)
Start scanning (P.22-24, 25-27)
Switch among bands (P.17)
Perform the Shift function (P.27)
Switch between 10MHz and
1MHz up/down (P.18)
Switch among functions
Adjust volume, squelch, and
other parameters/values
(P.14-15, 28)
Program to memory channels
(P.20)
Switch to the Tone Squelch
setting (P.26)
Switch among banks
Switch to the Shift setting (P.27)
Switch to the Set mode (P.28)
Perform the Priority Monitoring
function (P.25)
Switch to the setting of bank
links
Turn power ON/OFF (P.14)
Set and release the Key-lock
function (P.25)
Switch among the scanning
modes (P.22-24)
Independent Operation While is ON Holding for 1 Sec
Dial Operation with Holding
Key
PRI
MW
V/P/M
PWR
TONE
SCAN
BANK
BAND
SHIFT
10M/1M
Loading...