AirLive WN-200HD User Manual
W
N-200HD
2.0 Mega Pixel Wireless
150Mbps IP Camera
User’s Manual
i
Copyright & Disclaimer
Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether
electronic, mechanical, photocopying, or recording without the written consent of
OvisLink Corp.
OvisLink Corp. has made the best effort to ensure the accuracy of the information in
this user’s guide. However, we are not liable for the inaccuracies or errors in this
guide. Please use with caution. All information is subject to change without notice
This product contains some codes from GPL. In compliance with GPL agreement,
AirLive will publish the GPL codes on our website. Please go to
go to the "Support->GPL" menu to download source code.
All Trademarks are properties of their respective holders.
www.airlive.com and
i
AirLive WN-200HD User’s Manual
Copyright & Disclaimer
FCC Statement
Federal Communication Commission Interference Statement This equipment has
been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
z Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation. For product available in the USA/Canada market, only
channel 1~11 can be operated. Selection of other channels is not possible.
This device and its antenna(s) must not be co-located or operation in conjunction with
any other antenna or transmitter.
IMPORTANT NOTE
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
AirLive WN-200HD User’s Manual
ii
Table of Contents
Table of Contents
1. Introduction.....................................................................................................1
1.1 Overview.........................................................................................1
1.2 Features..........................................................................................2
1.3 System Requirements.....................................................................2
1.4 Package Contents...........................................................................3
1.5 Physical Description........................................................................3
1.5.1 Front View ..............................................................................3
1.5.2 Bottom View ...........................................................................4
1.6 Hardware Installation.......................................................................6
2. Getting Started ............................................................................................... 8
2.1 IP Wizard.........................................................................................8
2.1.1 View......................................................................................10
2.1.2 LAN ......................................................................................10
2.1.3 Wireless................................................................................13
2.2 UPnP for Windows........................................................................16
2.3 Install the IP Camera behind NAT router.......................................17
2.4 Configure IP Camera via Web UI..................................................18
2.4.1 Login as User .......................................................................19
2.4.2 Login as Administrator..........................................................20
3. Configure the Camera..................................................................................21
3.1 Monitor the Image Section ............................................................21
3.2 View Profile...................................................................................21
3.3 Streaming Protocol........................................................................21
3.4 Language......................................................................................21
3.5 Two-Way Audio.............................................................................21
3.6 Full Screen....................................................................................22
3.7 Active Control................................................................................22
3.7.1 Digital Zoom .........................................................................23
3.7.2 Snapshot ..............................................................................23
3.7.3 Record..................................................................................24
3.7.4 Volume .................................................................................25
3.7.5 About....................................................................................25
4. Monitor the Image Section ...........................................................................27
4.1 Monitor the Image Section ............................................................27
4.2 Configure via Web UI....................................................................27
4.2.1 Network ................................................................................27
iii
AirLive WN-200HD User’s Manual
Table of Contents
4.2.2 Wireless................................................................................29
4.2.3 DDNS...................................................................................33
4.2.4 PPPoE..................................................................................35
4.2.5 Steaming ..............................................................................37
4.2.6 UPnP....................................................................................38
4.2.7 Bonjour.................................................................................39
4.2.8 IP Filter.................................................................................40
4.2.9 IP Notification .......................................................................41
4.3 Camera – Adjust Camera Parameters ..........................................43
4.3.1 Picture..................................................................................43
4.3.2 Privacy Mask........................................................................45
4.4 System – Configure and Maintain .................................................46
4.4.1 System .................................................................................46
4.4.2 Date & Time..........................................................................48
4.4.3 Maintenance.........................................................................49
4.5 Video – Configure Profile ..............................................................51
4.5.1 Common...............................................................................52
4.5.2 Video Profile.........................................................................53
4.5.3 ROI.......................................................................................54
4.6 Audio – Audio Parameters ............................................................55
4.6.1 Setting..................................................................................55
4.6.2 Manage User Name, Password and Login Privilege ............56
4.6.3 E-Mail...................................................................................57
4.6.4 Object Detection...................................................................58
4.6.5 Storage – Status and Configuration of SD card....................60
4.6.6 Recording List- Files List inside SD Card .............................61
4.6.7 Event Sever..........................................................................61
4.6.8 Event Schedule ....................................................................66
5. Troubleshooting & FAQ................................................................................72
5.1 Monitor the Image Section ............................................................72
5.2 PING .............................................................................................78
5.3 Bandwidth Estimation....................................................................79
5.4 Specification Table........................................................................80
5.5 Configure Port Forwarding Manually.............................................82
5.6 DDNS............................................................................................85
5.7 Power Line Frequency ..................................................................92
5.8 3GPP Table...................................................................................94
5.9 UPnP.............................................................................................95
AirLive WN-200HD User’s Manual
iv
1
1. Introduction
1. Introduction
1.1 Overview
This camera is an inexpensive and fully scalable surveillance device. Because
the Network Cameras can be plugged into your existing local area network
(LAN), you will potentially save thousands of dollars from unnecessary cabling.
The device is accessible via the LAN or Internet connection. Connect your
device directly to a local area network or xDSL modem, and with Microsoft®
Internet Explorer you get instant, on demand video streams. Within minutes
you can set up the device to capture a video sequence to a PC. The live video
can be uploaded to a website for the world to see.
1
AirLive WN-200HD User’s Manual
1. Introduction
1.2 Features
z Easy installation with setup wizard (IP Wizard II)
z UPnP device discovery and NAT router transversal for easy installation
z Dynamic IP Service, DIPS®, to search your IP camera from Internet easily
z H.264, MPEG4 and JPEG triple compression simultaneously
z 2 Mega-pixel resolution
z Up to 9-profile encoder simultaneously
z 2 Mega-pixel or 720P mode selectable
z Up to 30 fps for 720P mode
z Up to 15 fps for 2 Mega-pixel mode
z UDP / TCP / HTTP protocols selectable
z IEEE 802.11n wireless LAN
z WEP/WPA/WPA2-PSK wireless security
z 3GPP for 3G mobile remote application
z Digital zoom
z Built-in microphone
z Audio line out
z Two-way audio
z Intelligent motion detection up to 10 zones
z Go to preset once motion triggered
z Image transmission using an FTP or e-mail for event
z DDNS and PPPoE
z Multi-channel control software for surveillance application
z On-line firmware upgrade
1.3 System Requirements
z Microsoft Internet Explorer 6.0 or later
z Microsoft Media Player 11.0 or later (to playback recorded file)
z VGA Monitor resolution 1280 x 1024 or higher
z Pentium-4 3.6 GHz or higher
z Memory Size: 1GB or more
z Windows XP, Vista, 7
AirLive WN-200HD User’s Manual
2
1. Introduction
1.4 Package Contents
User can find the following items in the package:
z This camera is the main element of the product.
z Camera Stand with screws
z Detachable WLAN antenna
z Power adapter dedicates 12V DC electric power output to Network
Camera.
z User’s manual CD provides important information and instructions for
operating the Network Camera.
z Quick start guide provides important information and instructions for
installing this device.
If any of the above items are missing, please contact your dealer immediately.
Note: Using a power supply with a different voltage than the one included with
the Network Camera will cause damage and void the warranty for this product.
1.5 Physical Description
1.5.1 Front View
3
AirLive WN-200HD User’s Manual
1. Introduction
1. Lens & Focus Ring
User could use this ring to adjust focus manually.
2. Microphone
The Camera has built-in an internal microphone. This microphone is hidden
in the pinhole located on the front panel.
3. Micro SD Card Slot
User can insert a micro SD card into this slot for event recording.
1.5.2 Bottom View
1. Audio Output Jack
Audio-out Jack allows this device to output audio or alerting sound.
2. DC Power Jack
The input power is 12VDC.
Note that supply the power to the Camera with the power adapter included in
package. Otherwise, the improper power adapter may damage the unit and
result in danger.
AirLive WN-200HD User’s Manual
4
1. Introduction
3. Antenna
User can attach the included antenna to antenna connector (SMA type) or
use another high-gain antenna to get higher performance.
4. Factory Default Reset
This button is hidden in the pinhole. This button is used to restore the all
factory default settings. Sometimes restarting the camera will make the
system back to a normal state. If the system still got problems after restart,
user can restore the factory default settings and install it again. To restore
the device, please follow the steps below:
(1) Insert the paper clip or other tool and press and hold the button down
continuously.
(2) Hold it at least 5 seconds and release the tool. Then the device has been
restored to default settings and reboot again.
Note: Restoring the factory default setting will lose the all previous settings
included IP address forever. User needs to run the IPWizard II program to
search the device and configure it to let the device work properly again.
5. LAN Socket
The LAN socket is a RJ-45 connector for connections to 10Base-T Ethernet
or 100Base-TX Fast Ethernet cabling. This Ethernet port built N-Way
protocol can detect or negotiate the transmission speed of the network
automatically. Please use Category 5 cable to connect the Network
Camera to a 100Mbps Fast Ethernet network switch or hub.
6. LAN LED (green color)
This LED will be flashing while network accessing via Ethernet.
7. Power / Wireless LED (orange color)
This LED is used to indicate whether DC power is on or not. In addition, this
LED will be flashing while the wireless accessing of the Camera.
5
AirLive WN-200HD User’s Manual
1. Introduction
1.6 Hardware Installation
1. Attach the Camera with the included stand
2. Place the Camera on the table or fix it onto ceiling or wall
Use three screws to fix the Network Camera onto the ceiling or wall. You could
also put the Network Camera on the table directly.
AirLive WN-200HD User’s Manual
6
1. Introduction
3. Plug an Ethernet cable into the Camera
Connect an Ethernet cable to the LAN socket located on the Network
Camera’s bottom and attach it to the network.
4. Connect the external power supply to Camera Connect the attached power
adapter to the DC power jack of the Network Camera.
Note: Use the power adapter, 12VDC, included in the package and connect it
to wall outlet for AC power.
7
AirLive WN-200HD User’s Manual
2
2.1 IP Wizard
2. Getting Started
2. Getting Started
Once you have installed the Network Camera well and powered it on, the
network accessing type LED will turn on. It means the system is booting up
successfully. Furthermore, if you have a proper network connection, and
access to the Network Camera, the LED will flash green under wired mode or
orange under wireless mode.
When you installed the Camera on a LAN environment, you have two easy
ways to search your Cameras by IPWizard II or UPnP™ discovery. Here is the
way to execute IPWizard II to discover Camera’s IP address and set up related
parameter in a Camera.
AirLive WN-200HD User’s Manual
8
2. Getting Started
When launch the IPWizard II, a searching window will pop up. IPWizard II is
starting to search Network Cameras on the LAN. The existed devices will be
listed as below.
9
AirLive WN-200HD User’s Manual
2. Getting Started
2.1.1 View
If IPWizard II finds network devices, View button will be available. Please
select the device you want to view and click the View button. Then you could
see the video from camera directly. Furthermore you could double click the left
button of mouse to link to the network device by browser.
2.1.2 LAN
In case you want to change the IP related parameters of wired interface,
please select the device you want to configure and click the LAN button.
Relative settings will be carried out as below.
AirLive WN-200HD User’s Manual
10
2. Getting Started
You could modify the relative settings of the selected device. Click “<<” button
will quit the LAN setting procedure and click “>>” button will move to next page
as below.
11
AirLive WN-200HD User’s Manual
2. Getting Started
In case, you do not want to change username and/or password, then just click
“Submit” button to perform your setting accordingly. Click “<<” button will go
back to previous page.
If you like to change username and/or password of the device, just click the
check button. Then, the related fields will show up as below.
After keying in new username and password, click “Submit” button to perform
your setting accordingly. Click “<<” button will go back to previous page.
AirLive WN-200HD User’s Manual
12
2.1.3 Wireless
2. Getting Started
In case you want to change the IP related parameters of wireless interface,
please select the device you want to configure and click the WIRELESS button.
Relative settings will be carried out as above.
13
AirLive WN-200HD User’s Manual
2. Getting Started
Click SSID to select your wireless AP or router and key in WEP or WPA key.
Click >> to next step:
AirLive WN-200HD User’s Manual
14
Make sure wireless setting and then submit it.
2. Getting Started
Click OK to confirm these parameters, then IPWizard II will start to configure
this camera with specified information.
15
AirLive WN-200HD User’s Manual
2. Getting Started
Once this step finished, IPWizard II will prompt you to unplug the Ethernet
cable to activate wireless access. Then IPWizard II will prompt you to test
wireless setting or finish wireless procedure as below.
2.2 UPnP for Windows
UPnP™ is short for Universal Plug and Play, which is a networking
architecture that provides compatibility among networking equipment, software,
and peripherals. This device is an UPnP enabled device. If the operating
system, Windows XP, Vista or 7, of your PC is UPnP enabled, the Network
Camera will be very easy to be found.
Please refer to Appendix I to enable UPnP settings only if your operating
system of PC is running Windows XP.
Note: Windows 2000 does not support UPnP feature.
AirLive WN-200HD User’s Manual
16
2. Getting Started
To discover your device, go to your Desktop and click My Network Places.
Click the targeted Device. Then Internet Explorer will connect to this Network
Camera automatically.
2.3 Install the IP Camera behind NAT router
Once installed, the device is accessible on your LAN. To access the device
from the Internet you must configure your broadband router to allow incoming
data traffic to the device.
then it may get a dynamic IP address from the DHCP server. However, if the
device wants to be accessed from the WAN, its IP address needs to be setup
as fixed IP, also the port forwarding or Virtual Server function of router needs
to be setup.
However, if your NAT router supports UPnP feature, it can be very easy to
achieve NAT traversal automatically. To do this, enable the NAT-traversal
feature, which will attempt to automatically configure the router to allow access
to the camera.
If the device is installed on the LAN with a router,
Installing the device with an UPnP router on your network is an easy 3–step
procedure:
(1) Enable UPnP option of your NAT router
(2) Enable UPnP NAT traversal option of the Network Camera (default)
(3) Access your Network Camera by DIPS
17
AirLive WN-200HD User’s Manual
2. Getting Started
(1) Enable UPnP option of your NAT router
To use UPnP IGD function (NAT traversal), you need to make sure the UPnP
function is enabled in your router. Most new home routers should support this
function. Some of routers are default enable and others are not. Please check
user’s manual of your NAT router for detail.
(2) Enable UPnP NAT traversal option of the Network Camera
Refer to Setting Î Network Î UPnP page for detail NAT traversal setting.
Note that this option is default enabled.
(3) Access your Network Camera by DIPS
Refer to Setting Î System Î System page for detail DIPS information.
2.4 Configure IP Camera via Web UI
1. Start the web browser on the computer and type the IP address of the
Camera you want to monitor as below:
The Login Window of the Camera is prompted:
AirLive WN-200HD User’s Manual
18
2. Getting Started
2. Type in your login name and password under “USERNAME” and
“PASSWORD” textbox. For the first time use (default value), input the
User Name: admin
Password: airlive
That’s, type in “admin” on the “USERNAME” as a default name and “airlive”
on the “PASSWORD” as a default password. Click “OK” button to start the
main menu.
3. According your browser’s security setting, the IE Web Page may prompt the
“Security Warning” window. If so, select “Yes” to install and run the ActiveX
control into your PC. Otherwise, the system will load the ActiveX silently.
4. After the ActiveX control was installed and ran, the first image will be
displayed.
2.4.1 Login as User
If you log in the Camera as an ordinary User, “Setting” function will be not
accessible.
19
AirLive WN-200HD User’s Manual
2. Getting Started
2.4.2 Login as Administrator
If you log in the Camera as the Administrator, you can perform all the settings
provided by the device.
Start-up screen will be as follow no matter an ordinary users or an
administrator.
ActiveX Control
Monitor
2-Way
Audio
Image
AirLive WN-200HD User’s Manual
Full Screen
20
3. Configure the Camera
3. Configure the Camera
3
3.1 Monitor the Image Section
The image shot by the device is shown here. The date and time are displayed
at the top of the window.
3.2 View Profile
The device supports multi-profile function for H.264, MEPG4 and JPEG
simultaneously. User can chose the proper and/or preferred profile which is
listed here.
3.3 Streaming Protocol
User can select proper streaming protocol according to networking
environment.
3.4 Language
The device could provide multiple languages to meet customer’s requirement.
3.5 Two-Way Audio
The device supports 2-way audio function. User can chose to enable or
disable this function by toggling the icon below.
: Disable audio uploading function.
: Enable audio uploading function.
21
AirLive WN-200HD User’s Manual
3. Configure the Camera
3.6 Full Screen
Enlarge video to full screen display.
: Enlarge video to full screen display. Press “ESC” key to disable
this function.
3.7 Active Control
The plug-in ActiveX control supports a lot of functions by clicking the left
mouse button. Note that this feature only supports on the ActiveX control within
Microsoft® Internet Explorer.
On the ActiveX control icon, click the LeftMouseButton, then a menu pop-up.
This menu provides features that are unique to the ActiveX control. These
features include:
• “Digital Zoom”,
• “Snapshot”,
• “Record”,
• “Volume”,
• “About”
AirLive WN-200HD User’s Manual
22
3. Configure the Camera
3.7.1 Digital Zoom
Click Digital Zoom to active this function as above. User can drag or scale the
box over the video to adjust zoom ratio and position.
3.7.2 Snapshot
23
AirLive WN-200HD User’s Manual
3. Configure the Camera
Click Snapshot to activate this function. Press Snapshot button to take a
picture. The image file is saved as JPEG format into your local PC. Select
Browser, the pop-up window to select the save path and file name prefix,
select OK to continue.
If you like to retrieve the saved image, select the file to display the saved
image by using any one of graph editing tools.
3.7.3 Record
Click Record to activate this function. Press Record button to start recording.
The video file is saved as ASF format into your local PC. While you want to
AirLive WN-200HD User’s Manual
24
3. Configure the Camera
stop it, press Stop to stop recording. Select Browser, the pop-up window to
select the save path and file name prefix, select OK to continue.
After stop recording, list the files, this file is named as
Video_yyyymmddhhmmss.avi
The ASF files can be display by the standard Windows Media Player, but it
needs the DixectX 9.0 or later version to be installed.
3.7.4 Volume
Click Volume to activate this function. There are two control bars for speaker
and microphone volume respectively. Scroll these control bars to adjust the
audio attribute. Check the volume mute will mute the speaker output.
3.7.5 About
25
AirLive WN-200HD User’s Manual
Loading...