Airlive WL-5470AP User Manual

WL-5470AP

802.11g Hi Power Multifunction AP/Router

5-port Hi-Power AP

he WL-5470AP is a multi-function AP designed for various different wireless applications. On the

hardware side, it features 5 LAN ports and hardware hi-power amplifier that can boost the output power from standard 18dBm to over 25dBm*. On the software front, the WL-5470AP includes both powerful features and an easy-to-use interface to satisfy the demand of WISP operators, Home, or Office users.

8 Wireless Operating Modes

The WL-5470AP features an incredible 8-mode firmware.

AP mode

The most basic mode of multi-function Access Point. In this mode, the AP will act as a central hub for different Wireless LAN clients. Some hotspot APs requires

802.1x authenticator function to authenticate a user before providing Internet service.

WLAN PCI

Wireless AP

WLAN USB

Client Mode

Also known as Ethernet Client. In this mode, the AP will act as a WLAN card to connect with the remote AP. Users can connect PC or local LAN to the Ethernet port of the client mode AP. This mode is mostly used as a CPE device for WISP subscriber .

Bridge mode

In this mode, 2 access points in two remote locations connect to each other to provide a wireless bridge between 2 remote LANs. It is mostly used by enterprise to connect 2 remote office's network together. The bridge modes are connected by using either the WDS (Wireless Distribution System) or Adhoc topology

WDS Repeater

A repeater's function is to extend the wireless coverage of another wireless AP or router . For WDS repeater to work, the remote wireless AP/Router must also support WDS function.

Universal Repeater

An universal repeater can also extend the wireless coverage of another wireless AP or router . But the universal repeater does not require the remote device to have WDS function. Therefore, it can work with almost any wireless device.

WISP (Client Router) mode

In WISP mode, the AP will behave just the same as the Client mode for wireless function. However , router functions are added between the wireless WAN side and the Ethernet LAN side. Therefore, the WISP subscriber can share the WISP connection without the need for extra router.

WISP + Universal Repeater mode

In this mode, the AP behaves virtually the same as the WISP mode, except one thing: the AP can also send wireless signal to the LAN side. That means the AP can connect with the remote WISP AP and the indoor wireless card, and then provide IP sharing capability all at the same time! However, the output power is divided between 2 wireless side and proper antenna installation can influence the performance greatly.

WISP

Outdoor AP

LAN

WDS Wireless

Router

Wireless

Router

WISP

Outdoor AP

WISP

Outdoor AP

Bridge

Client Mode

WDS Repeater

Universal Repeater

Client Router

WISP + Universal

Bridge

NAT

LAN

NoteBook

PC PC PC

Gateway mode

In gateway mode. The AP will behave like a broadband router . One of the LAN port will behave as a WAN port for wired connection to ADSL or Cable modem. The NAT routing will be performed between the W AN and LAN port. Making IP sharing possible.

5F, No.96, Min-ChuanRd, Hsin-tien City, Taipei, Taiwan

Internet

ADSL or

Cable Modem

Wireless AP

NoteBook

WDS Site Survey and Universal Site Survey.

The WL-5470AP adds WDS and Universal Site Survey to make bridge and repeater configuration much easier. Now you no longer have to look around for remote AP’s MAC address to establish a bridge connection.

Boot loader Protection

The WL-5470AP feature the boot loader protection. Even if the machine’s firmware crashed during firmware upgrade, the users can still recover the AP. This makes WL-5470AP much more reliable than other Realtek 8186 based AP.

Wireless Client Isolation

The WL-5470AP features the new Wireless Client Isolation function previous available only in more expensive APs. When you enable this function, the wireless clients will not be able to see each other. Therefore, it is an important function for office and Hotspot operator to protect the security between different wireless users.

for law compliance. The ability to set lower TX output power is also crucial if you want to match the AP with external power amplifier.

Extended Security Features

The WL-5470AP support WEP, WPA and WPA2 security functions. In addition, WPA enterprise for 802.1x authenticator are featured for AP and WDS mode. The combination of Encryption, Hide SSID and Access Control ensures your wireless network is completely secured from intruder.

The WL-5470AP’s firmware features list are much longer than what has been described. Better yet, OvisLink Corp. are known to continuous upgrade the firmware for new features. Whether it’ s for WISP, Hotspot, or Home uses, the WL-5470AP is perfect for everyone.

ACK Timeout and TX Power Regulation

The WL-5470AP features ACK timeout function to let you adjust the timeout value for long distance operation. In addition, 5-level TX power adjustment let you match different antennas

FEATURES & SPECIFICATIONS

Features

- AP, Bridge, Client, Repeater, functions

- Router and Gateway mode

- WISP Client Router mode

- WISP + Universal Repeater Mode

- Up to 25dBm output power

- Hardware Power Amplifier

- Detachable Antenna, 5 LAN ports

- 802.1x, WPA, WPA2 and Web Mgt.

- TX power regulation in 4 levels

- Watchdog function use PING

* The TX output power is limited to 20dBm in EU, 23dBm in U.S., and 27dBm in South America

- Wireless Client Isolation

- WDS Site Survey

- ACK Timeout Adjustment

- DHCP Relay function

- 802.11g Protection

- MAC Access Control

- Telnet

Speciﬁ cations

Hardware:

- 5 x 10/100Mbps LAN Port

5F, No.96, Min-ChuanRd, Hsin-tien City, Taipei, Taiwan

+ 1 hidden pages