3xLogic VX-2A-B-RIWDZ, VX-2AD3B-IWD, VX-2AD3-IWD, VX-2A-IMD-X, VX-2VA-B-RIWD Hardware And Installation Manual

Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I

10385 Westmoor Drive, Suite 210, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC

1

VISIX V-Series All-in-One Cameras - Gen I

Hardware and Installation Manual

2018-3

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

2

This manual applies to the following camera models. Please use the below links or the Table of Contents
to locate the section of this manual that pertains to your particular All-in-One camera model:

Camera Type

Model

Exterior Bullet Camera

VX-2A-B-RIWDZ (New), VX-2A-B-IWD (DC)

Exterior Bullet Camera w/Remote Focus

VX-2VA-B-RIWD (New), VX-2A-B-RIWD (DC)

Exterior Dome Camera

VX-2AD3B-IWD (New), VX-2AD3-IWD (DC)

Interior Mini Dome Camera

VX-2A-IMD-X

VERA 20°, 36° or 50° Field-of-Vision Thermal Bullet
Camera

VX-VT-20, VX-VT-36, VX-VT-58 (New)

Interior Pinhole Camera

VX-2V28-PIN

Please use the links above or the Table of Contents to locate the section of this manual that pertains to
your particular All-in-One camera model.

Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to
contact the dealer.

This manual may contain technical inaccuracies or printing errors. The content is subject to change
without notice. The manual will be amended if there are any hardware updates or changes.

Disclaimer Statement

“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or

signaling aspects of this product. UL has only tested for fire, shock or casualty hazards as outlined in UL’s
Standard(s) for Safety, UL60950-1. UL Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

3

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and found to comply with the limits for a digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired

operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information, see: www.recyclethis.info

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

4

Safety Instruction

These instructions are intended to ensure that the user can use the product correctly to avoid danger or

property loss.

The precaution measure is divided into ‘Warnings’ and ‘Cautions’:

WARNING: Serious injury or death may be caused if any of these warnings are neglected.
CAUTION: Injury or equipment damage may be caused if any of these cautions are neglected.

WARNINGS:

 Please adopt a power adapter which can meet the safety extra low voltage (SELV) standard

when possible, and source with 12 VDC or 24 VAC (depending on models) according to the
IEC60950-1 and Limited Power Source standard. Before applying power to the camera,
check the power source to ensure that it is within the specifications

 If the product does not work properly, please contact your dealer or the nearest service

center. Never attempt to disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)

 To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture

unless it is an exterior/weatherproof model. Please do not install the camera in a place
exposed to direct sunlight. Do not operate the camera in environments beyond the
specified temperature. Refer to your specific camera model’s section of this manual for
environmental conditions and limitations.

 This installation should be made by a qualified service person and should conform to all the

local codes.

 Please install blackout equipment into the power supply circuit to prevent footage and

data loss.

 Please make sure that the ceiling can support more than 50(N) Newtons of gravity if the

camera is fixed to the ceiling.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

5

CAUTIONS:

 Make sure the power supply voltage is correct before using the camera.
 Do not drop the camera or subject it to physical shock.
 Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a

bit of ethanol and wipe it gently. If the camera will not be used for an extended period of
time, put on the lens cap to protect the sensor from dirt.

 Do not aim the camera lens at the strong light such as sun or incandescent lamp. The

strong light can cause fatal damage to the camera.

 The sensor may be burned out by a laser beam, so when any laser equipment is being

used, make sure that the surface of the sensor not be exposed to the laser beam.

 Do not place the camera in extremely hot, cold temperatures (the operating temperature

should be between -30°C ~ 60°C, or -40°C ~ 60°C if the camera model has an “H” in its
suffix), dusty or damp environment, and do not expose it to high electromagnetic
radiation.

 To avoid heat accumulation, good ventilation is required for a proper operating

environment.

 Keep the camera away from water and any liquid.
 While shipping, the camera should be packed in its original packing.
 Improper use or replacement of the battery may result in hazard of explosion. Please use

the manufacturer recommended battery type.

NOTE: For cameras that support IR, you are required to pay attention to the following precautions to

prevent IR reflection.

► Dust or grease on the dome cover will cause IR reflection. Please do not remove the

dome cover film until the installation is finished. If there is dust or grease on the dome
cover, clean the dome cover with clean soft cloth and isopropyl alcohol. (only applies
to certain models).

► Make certain the installation location does not have reflective surfaces of objects too

close to the camera. The IR light from the camera may reflect back into the lens
causing reflection. (only applies to certain models).

► The foam ring around the lens must be seated flush against the inner surface of the

bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so
that the foam ring and the dome cover are attached seamlessly (only applies to certain
models).

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

6

Table of Contents

1 VISIX V-SERIES ALL-IN-ONE CAMERAS ............................................................................................ 8

1.1 INTRODUCTION ................................................................................................................................. 8

2 VX-2A-B-RIWDZ / VX-2VA-B-RIWD - 2MP EXTERIOR BULLET CAMERA ........................................... 9

2.1 VX-2A-B-RIWDZ/ VX-2-VA-B-RIWD SPECIFICATIONS- QUICK SUMMARY ............................................... 9

2.2 PACKAGE CONTENTS ........................................................................................................................ 10

2.3 PART NAMES .................................................................................................................................. 11

2.4 INSTALLATION ................................................................................................................................. 12

2.4.1 Installing the Camera – Installation without Bracket ......................................................... 12

2.4.2 Adjusting angle of the camera ............................................................................................ 14

2.4.3 Adjusting Zoom and Focus (VX-2A-B-IWD Model Only) ...................................................... 14

2.5 CONNECTIONS ................................................................................................................................ 15

2.6 FULL CAMERA SPECIFICATIONS ........................................................................................................... 17

2.7 CAMERA DIMENSIONS ...................................................................................................................... 19

3 VX-2AD3B-IWD / VX-2AD3-IWD - 2 MP EXTERIOR DOME CAMERA .............................................. 20

3.1 VX-2AD3B-IWD SPECIFICATIONS- QUICK SUMMARY ........................................................................... 20

3.2 PACKAGE CONTENTS ........................................................................................................................ 21

3.3 PART NAMES .................................................................................................................................. 22

3.4 INSTALLATION ................................................................................................................................. 23

3.4.1 Installing the Camera – Installation without Bracket ......................................................... 23

3.4.2 Reattachment of Dome Cover – Alignment ........................................................................ 25

3.4.3 Adjusting angle of the camera ............................................................................................ 25

3.4.4 Connections ........................................................................................................................ 26

3.5 FULL CAMERA SPECIFICATIONS ........................................................................................................... 27

3.6 CAMERA DIMENSIONS ...................................................................................................................... 29

3.7 COMPATIBLE ACCESSORY INSTALLATION (MOUNTS) ............................................................................... 30

3.7.1 Wall Mount- VX-2AD-WM ................................................................................................. 30

3.7.2 Ceiling Mount- VX-2AD-CM ............................................................................................... 32

3.7.3 Pendant Mount Cap - VX-2AD-PMCB ................................................................................. 34

3.7.4 Gang Box Mount – VX-2AD-GB ........................................................................................... 35

4 VX-2A-IMD-X - 2 MP INTERIOR MINI DOME CAMERA ................................................................... 37

4.1 VX-2A-IMD-X SPECIFICATIONS - QUICK SUMMARY .............................................................................. 37

4.2 PACKAGE CONTENTS ........................................................................................................................ 38

4.3 PART NAMES .................................................................................................................................. 39

4.4 INSTALLATION ................................................................................................................................. 40

4.4.1 Installing the Camera – Installing without Bracket ............................................................ 40

4.4.2 Adjusting angle of The camera ........................................................................................... 42

4.5 CONNECTIONS ................................................................................................................................ 42

4.6 FULL CAMERA SPECIFICATIONS ........................................................................................................... 43

4.7 CAMERA DIMENSIONS ...................................................................................................................... 45

4.8 COMPATIBLE ACCESSORY INSTALLATION (MOUNTS) ............................................................................... 46

4.8.1 Wall Mount - VX-2AIMD-WM ............................................................................................. 46

4.8.2 Location of the Holes for M3x6L Bolts ................................................................................ 48

4.8.3 Ceiling Mount - VX-2AD-CM ............................................................................................... 49

4.8.4 Pendant Mount Cap - VX-2AD-PMC .................................................................................... 51

5 VX-VT-20, VX-VT-36, VX-VT-58 – VERA 20°, 36°, 58° THERMAL BULLET CAMERA .......................... 53

5.1 VX-VT-20, VX-VT-36, VX-VT-58 SPECIFICATIONS – QUICK SUMMARY .................................................. 53

5.2 PACKAGE CONTENTS ........................................................................................................................ 54

5.3 PART NAMES .................................................................................................................................. 55

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

7

5.4 INSTALLATION ................................................................................................................................. 56

5.4.1 Installing The camera – installation without bracket ......................................................... 56

5.4.2 Adjusting angle of The camera ........................................................................................... 58

5.5 CONNECTIONS ................................................................................................................................ 59

5.6 FULL CAMERA SPECIFICATIONS ........................................................................................................... 61

5.7 CAMERA DIMENSIONS ...................................................................................................................... 62

6 VX-2V28-PIN – IP PINHOLE CAMERA ............................................................................................ 63

6.1 VX-2V28-PIN SPECIFICATIONS — QUICK SUMMARY ............................................................................ 63

6.2 PACKAGE CONTENTS ........................................................................................................................ 64

6.3 PART NAMES .................................................................................................................................. 65

6.3.1 Main Unit: ........................................................................................................................... 65

6.3.2 Camera Unit with Conjoined Accessories............................................................................ 66

6.4 INSTALLATION ................................................................................................................................. 67

6.4.1 Camera Unit Installation ..................................................................................................... 67

6.4.2 Inconspicuous Installation .................................................................................................. 67

6.4.4 Surface Installation for Fixed Angle .................................................................................... 69

6.4.5 Surface Installation for Pan/Tilit Adjustment ..................................................................... 70

6.4.6 MAIN UNIT INSTALLATION .................................................................................................. 71

6.5 CABLE CONNECTION ......................................................................................................................... 73

6.5.1 DI/Do Terminal Connector .................................................................................................. 73

6.5.2 Camera Connector .............................................................................................................. 74

6.5.3 LAN Connector .................................................................................................................... 75

6.5.4 Power Connector ................................................................................................................ 75

6.6 CAMERA DIMENSIONS ...................................................................................................................... 76

6.7 FULL CAMERA SPECIFICATIONS ........................................................................................................... 77

7 POWER OVER ETHERNET SPECIFICATIONS .................................................................................... 79

7.1 POWER COMPARISON ...................................................................................................................... 79

8 REVISION HISTORY ....................................................................................................................... 80

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

8

1 VISIX V-Series All-in-One Cameras

1.1 Introduction

VISIX V-Series All-in-One, edge-based IP cameras are powerful, full-featured, VMS and advanced analytic
capable. VISIX V-Series cameras provide a complete surveillance solution for the small and medium sized
businesses and for unique single-point applications.

Several models exist to best suit any number of environments. Hardware installation details for each
model are contained within. Use the Table of Contents to locate the Section pertaining to your particular
camera model.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

9

2 VX-2A-B-RIWDZ / VX-2VA-B-RIWD - 2MP

Exterior Bullet Camera

The VX-2A-B-RIWDZ (previous model: VX-2A-B-IWD) and VX-2VA-B-RIWD (previous model: VX-2A-B­RIWD) are fully functional indoor/outdoor IP cameras with advanced analytics capabilities. These
cameras can be connected to a DVR or act as a standalone recording device. The exterior bullet camera
line offers high-definition video at full 1920 x 1080 resolution for both indoor and outdoor video
surveillance applications which require superior clarity and detail.

The wealth of features includes; dual-streaming of either H.264 or MJPEG compression; wide dynamic
range; Micro SD card slot for local recording; IP66 weather resistant construction; varifocal lens; and IR
illumination. The RIWD model also features remote one-click auto focus.

The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate
on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to
configure a detection rule. These advanced analytics allow for object classification, direction, people
counting, dwell times, and occupancy counts.

When enabled, the embedded VIGIL Server software from 3xLOGIC allows the camera to be run as a
stand-alone device recording video to the onboard memory card. This makes the camera compatible
with the 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud
applications. Simple plug-and-play installation allows for access using a standard web browser, VIGIL
Client, or your mobile device or tablet using our easy to use QR code quick setup.

2.1 VX-2A-B-RIWDZ/ VX-2-VA-B-RIWD Specifications- Quick

Summary

Component

Feature Description

Camera

 SONY EXMOR 1/2.9” 1080p CMOS Image Sensor
 True Day / Night
 DC Auto Iris Lens
 WDR
 Embedded IR Illuminator
 Weather Proof (IP66)
 Remote Zoom/Focus Control (One Click AF) - ** VX-2-VA-B-RIWD

Only**

Video

 H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC),

MJPEG(Motion JPEG)

 Max 30fps in 1080p
 Text Overlay
 Analog Video Output

Network

 10/100 Base-T Ethernet

Integration

 ONVIF compliant (Profile S)

General

 Micro SD/SDHC Card Slot x1
 Power over Ethernet (PoE)

Video Contents Analysis
(VCA)

 VCA Presence Standard

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

10

2.2 Package Contents

Please unpack the package carefully and handle the equipment with care. The package contains:

NOTE: The contents above are subject to change without prior notice.

Camera

DC Power Adaptor

Universal Plugs

Screws(M4x30) and Plastic Anchors

Quick Installation Guide

Hex Wrench(3mm)

Silicon Waterproof Band

Video Output Cable

Installation Template

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

11

2.3 Part Names

1). Sunshield: Position the sunshield to prevent direct sunshine.

2). Video-Out Cable Socket: Socket for the video output cable included in the package (CVBS: 1.0Vp-p /

75Ω BNC)

3). PAL/NTSC button: Pressing the PAL/NTSC button each time changes the mode as follows: No video

output -> PAL-> NTSC

4). Reset button: Use the button to restart the device or to reset it to Factory Default. Refer to the

3xLOGIC VISIX All-in-One Camera User Manual for more details on restarting/resetting to factory
default.

5). Focus Puller: Use the puller to manually determine correct focus of the camera. Refer to Adjusting

Zoom and Focus for more details.

6). Zoom Puller: Use the puller to manually determine appropriate field of view of the camera. Refer to

Adjusting Zoom and Focus for more details.

7). microSD memory card slot: The camera supports up to 32GB. A card with Class 4 and higher is

recommended for HD recordings.

8). Terminal Connector: Connector for cable connection of digital input/output. Refer to Section 2.5:

Connections for more details.

9). Power Adaptor Connector: Use DC12V for the power supply.

10). LAN connector: RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported)

❾

* Models herein and their appearance are subject to change without any prior notice.

❸

❹

❿

❽

❷
❼

❺

❶

❻

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

12

2.4 Installation

2.4.1 INSTALLING THE CAMERA – INSTALLATION WITHOUT BRACKET

Installation Template

NOTE: Installation template’s image size scale in this installation guide is not 1:1. The correct-size

template design paper can be found inside the package separately.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

13

Steps:

1). Place the installation template included in the package

on the desired installation surface.

2). Drill three holes in correct positions based on the

template paper, and insert the anchor blocks into the
holes.

3). Attach the silicon waterproof band included in the

package to the camera’s mounting surface by aligning it
with the three alignment holes.

4). Connect the required cables including a power cable

and a LAN cable (or PoE connection) to the device. See
Section 2.5: Connections for a diagram of the correct
connections.

5). Place the camera body to match the three alignment

holes with the three anchor blocks, and hold the camera
against the surface where the camera will be mounted.

6). Tighten the anchor blocks with the screws.

7). Adjust the heading direction of the camera. Refer to

Adjusting Angle of the Camera for more details.

8). Adjust zoom and focus of the camera. Refer to Adjusting

Zoom and Focus for more details.

9). Attach the lens cover on the main body by rotating it

clockwise

CAUTION: Sealing gaps is recommended as gaps may appear after

the camera installation. Gaps may cause problems such as
moisture, water leakage, and etc., which negatively affects the
operation of the camera if gaps remain unsealed.

CAUTION: To prevent products from damage, place the camera

on a stable and non-vibrating surface. If the stability is in doubt,
consult safety personnel for reinforcements, and then proceed
with the installation.

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

14

2.4.2 ADJUSTING ANGLE OF THE CAMERA

Adjust the camera to the desired angle by unscrewing the joints referring to the following pictures.

Steps:

1). Insert the video output cable (included in the

package) to the video output cable socket, and
connect it to an analogue video test monitor to
check if the camera angle has been set as
intended. If the angle is appropriate, disconnect
the camera from the analogue monitor, and then
remove the video output cable from the camera.

2.4.3 ADJUSTING ZOOM AND FOCUS (VX-2A-B-

IWD MODEL ONLY)

Steps:

1). Unscrew the zoom puller and the focus puller

counter-clockwise.

2). Adjust the zoom and the focus of the lens.

3). Tighten the zoom puller and the focus puller again by

turning it clockwise after the zoom and the focus are
properly adjusted.

CAUTION: Manual adjustment of Zoom and Focus is only

possible on the VX-2VA-B-IWD model version. Zoom and Focus controls can be configured digitally from

the camera’s web interface for VX-2VA-B-RIWD models. See the VISIX V-Series All-in-One Camera User
Manual for more details on adjusting lens settings from the camera’s web interface.

Adjust the joint to install
the camera on the wall.

Tilting adjustment

Panning adjustment

Zoom Puller

Focus Puller

Reset

PAL/NTSC

Video output
cable

socket

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

15

2.5 Connections

LAN cable

GREEN : DI

WHITE : DI COM
ORANGE : DO

YELLOW : DO COM

(not included)

DC 12V

❶

❷

❸

❹

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

16

1). Sensor (DI) connection: Sensor (DI) can be connected to either a voltage type sensor or a relay type

sensor as the following figures. Settings can be done through the camera’s webpage.

 Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA.

CAUTION: Do not exceed the maximum input voltage or relay rate.

2). Alarm (DO) Connection: Only the relay type is supported.

 Relay Rating: Max 24VDC 50mA

CAUTION: Do not exceed the maximum relay rating.

3). LAN Connection: This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable

(RJ45. to connect the device to a hub or a router in the network. Refer to Section 6: Power over

Ethernet Specifications to for further detail.

4). Power Connection: The camera can be powered from either 12VDC or PoE. If the camera is

powered via PoE, refer to Section 6: Power over Ethernet Specifications for further detail.

+3.3V

DI

COM

DI

COM

+

-

Relay Type

Voltage Type

+

-

Output of
Sensor

Output of
Sensor

Internal

Internal

+

-

DO

COM

Relay Type

Device

Internal

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

17

2.6 Full Camera Specifications

Camera Module

CMOS

Image Sensor

SONY EXMOR 1/2.9” 1080p CMOS

Effective Pixels

1920x1080

Scanning system

Progressive scanning

Electrical

Resolution

1920 x 1080

Min. Illumination

Color: 0.7 lux, BW: 0 lux (IR LED On)

AGC Control

Auto

Lens

3.0(w) – 9.0mm(t), F1.5(w) – F2.5(t), Optical 3x

Day & Night

Removable IR Cut Filter

Wide Dynamic
Range

Digital WDR

IR Illuminator

IR LED

High Power IR LED x 12 (850nm)

IR Working
Distance

Max. 30m (98ft)

Video

Compression
Format

H.264 and MJPEG Selectable per Stream

Number of
Streams

Dual Stream, Configurable

Resolution

1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180

Compression FPS

30fps@1080p

Motion Detection

Built-in

Burnt-in Text
(Digital)

Time stamp and text caption overlay

Analogue Output

NTSC/PAL

Audio

Input/output

-

Compression
Format

-

Function

Digital
Input/Output

1/1 channel

RS-485

Not supported

Network

10/100 Base-T

Power over
Ethernet (PoE)

Supported

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

18

Function

Protocol

QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIB­II), IGMP, ICMP, SSLv2/v3, TLSv1

SD Slot

1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)

Electrical Characteristics

Power Source

DC 12V / PoE

Power
Consumption

Max. 6W @ DC 12V

Video Output

1 Vp-p, 75, Composite

Audio Input

-

Audio Output

-

D/I

Max 50mA@5VDC, TTL level 1.5V threshold

D/O

Max 50mA@24VDC
On-state resistance: 50  (max continuous)

Environment Condition

Operating
Temperature

[DC12V] -20°C ~ 50°C (-4°F ~ 122°F)
[PoE] -20°C ~ 50°C (-4°F ~ 122°F)

Operating
Humidity

Up to 85% RH

Mechanical Condition

Material

Aluminum Die-Casting

Color

Ivory

Dimension

83.5mm X 86mm X 287 mm

Weight (Approx.)

860g (1.90lbs)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

19

2.7 Camera Dimensions

 2.68 in.
(68 mm)

3.29 in. (83.5 mm)

9.41 in. (239 mm)

4.67 in. (118.5 mm)

3.39 in. (86 mm)

3.29 in. (83.5 mm)

11.02 in. (280 mm)

11.30 in. (287 mm)

3 x .197 in. (5mm)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

20

3 VX-2AD3B-IWD / VX-2AD3-IWD - 2 MP Exterior

Dome Camera

The VX-2AD3B-IWD (previous model: VX-2AD3-IWD) is a fully functional indoor/outdoor IP camera with
advanced analytics capabilities. These cameras can be connected to a DVR or act as a standalone
recording device.

The exterior dome offers high-definition video at full 1920 x 1080 resolution for both indoor and
outdoor video surveillance applications which require superior clarity and detail. Its many features
include; dual-streaming of either H.264 or MJPEG compression; wide dynamic range; Micro SD card slot
for local recording; IP66 weather resistant construction and IR illumination.

The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate
on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to
configure a detection rule. These advanced analytics allow for object classification, direction, people
counting, dwell times, and occupancy counts.

When enabled, the embedded VIGIL Server software allows the camera to be run as a stand-alone
device recording video to the onboard memory card. This makes the camera compatible with the
existing 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud
applications. Simple plug and play installation allows for access using a standard web browser, VIGIL
Client, or set it up on your mobile device or tablet using our easy to use QR code quick setup.

3.1 VX-2AD3B-IWD Specifications- Quick Summary

Component

Feature Description

Camera

 1/2.9” 1080p CMOS Image Sensor
 True Day/Night
 WDR
 Embedded IR Illuminator

Video

 H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC), MJPEG (Motion

JPEG)

 Max 30fps in 1080p
 Text Overlay

Network

 10/100 Base-T Ethernet

Integration

 ONVIF compliant (Profile S)

General

 Micro SD/SDHC Card Slot x1
 Power over Ethernet (PoE)

Video Contents
Analysis (VCA)

 VCA Presence Standard

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

21

3.2 Package Contents

Please unpack the package carefully and handle the equipment with care. The package contains:

Camera

Screw(M4x35) & Plastic Anchors

Quick Installation Guide

Torx (T20) Wrench

O-ring & Waterproof Bracket

Installation Template

Bottom Pad

Adaptor & AC Plug

NOTE: The contents above are subject to change without prior notice.

Camera

Camera

Cable

Camera

Cable

Torx Wrench

Screw &
Plastic Anchor-3pcs

Quick Installation Guide

O-ring &
Waterproof Bracket

Bottom Pad

Installation Template

Camera

Cable

Torx Wrench

Screw &
Plastic Anchor-3pcs

O-ring &
Waterproof Bracket

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

22

3.3 Part Names

1) Safety Wire: The dome cover is attached to the camera body with this safety wire to prevent

the dome cover from being dropped.

2) Ambient Light Sensor: Used to detect the level or the intensity of light for the IR operation. The

sensor should not be blocked by any object.

3) MicroSD/SDHC Card Slot: Up to 32GB supported. Class 4 and higher recommended for HD

recordings.

4) Reset Button: Use the button to restart the device or to reset it to Factory Default. Refer to the

3xLOGIC VISIX All-in-One Camera User Manual for more details on restarting/resetting to
factory default.

5) RJ-45: Connect an RJ-45 LAN cable for 10/100 Base-T Ethernet (PoE supported).

6) DC Power Jack: Connect the provided DC12V adaptor for the power supply unless it is PoE

powered.

* Models herein and their appearance are subject to change without any prior notice.

Reset Button

DC Power

RJ-45

Safety Wire

Ambient Light Sensor

microSD/SDHC Card Slot

❻

❷

❶
❺

❹
❸

Safety Wire

Ambient Light Sensor

mircoSD/SDHC Card Slot

Reset Button

RJ-45

DC Power

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

23

3.4 Installation

3.4.1 INSTALLING THE CAMERA – INSTALLATION WITHOUT BRACKET

Installation Template

CAUTION: Installation template’s image size scale in this installation guide is not 1:1. The correct-size

template paper can be found inside the product packaging.

M o unting tem p late

 4.92 in.
(125 mm)

 .255 in. (6.5 mm)

Hardware and Installation Manual| VISIX V-Series All-in-One Cameras – Gen I

12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC

24

Steps:

1). Place the installation template included in the package on the desired installation surface.

2). Drill two holes for the plastic anchors and a big hole for the cable lines based on the template

paper, and insert the plastic anchors into the drilled holes.

3). Attach the provided bottom pad to the bottom of the camera body for the prevention of

water permeation.

4). Detach the dome cover from the camera body by loosening the three screws with the

provided T20 Torx wrench.

5). Make the screws (M4x35) ready for the installation: Insert the provided waterproof bracket

and the O-ring into the screw in a row by placing the head of the bracket beneath the screw
head by reference to the squared image on the left.

6). Take the camera to the ceiling, and connect the necessary cables including a LAN and power

cable (or PoE cable) dropped from the ceiling to the corresponding connectors on the camera.

7). Align the screw holes on both sides of the camera body and the installation surface, insert the

screws prepared at the step 5 into the screw holes on the camera body, and tighten them into
the plastic anchors on the ceiling with a screw driver.

8). Adjust the angle of the camera. Refer to Adjusting Angle of the Camera for more details.

9). Reattach the dome cover to the camera body by aligning the screws on the dome cover with

the alignment holes on the camera body. Refer to the caution below for the alignment
method.

10). Once properly aligned, tighten the screws into the camera body with the provided Torx

wrench for the firm attachment of the dome cover. Then, remove the protection film from the
dome cover.

Bottom

O-Ring

Waterproof Bracket

Screw
(M4x35)

Torx Bolt
(M4 x 20)