3M Fiber Optic Connector Crimp Tool User Manual

Fiber Optic Connector Crimp
Tool

Instructions

Issue 1, August 1993

The universal 3M brand Fiber Optic Connector Crimp T ool
is designed to be used with all 3M field-mountable
connectors. The package contains three sets of crimping
dies. Each set of dies is designed for different connectors
and their marking and application are shown in the following
table.

Die

Marking

BC/ST .151

SC SC and FC-3

PPST

Cavity

Marking

.178
.213

.120
.137
.190

.120
.137
.226

Application

ST* (BAYONET), FC-1, BICONIC
TECS (SMA) 200/230
PROTECTIVE COVER-8500
SPLICE

2.4mm CABLE CRIMP RING

3.0mm CABLE CRIMP RING
KEVLAR CRIMP AREA

ST ( PUSH PULL)

2.4mm CABLE CRIMP RING

3.0mm CABLE CRIMP RING
KEVLAR CRIMP AREA

Installing the Dies in the Base Tool

1. Select the appropriate set of dies as identified in
the table above.

2. Squeeze and release the handles of the crimp tool
to open the jaws.

3. Insert the dies into the jaws with the deep half of

the

round dies into the movable jaw. Match the

shallow

half with corresponding cavities before inserting.

4. Retain the dies loosely with the thumb screws.

Movable

Jaw

CONNECTOR

STYLE

BICONIC**
SC/FC-3
ST* (BAYONET) and FC-1
ST* (PUSH PULL) EPOXY ADHESIVE
ST* (PUSH PULL) HOT MELT ADHESIVE
ST* (BAYONET) HOT MELT ADHESIVE

TECS (SMA)

**

To prevent deformation of the Biconic

Thumb Screws
(To secure dies)

(Crimp T ool Not

housing, insert the connector from the non­recessed side of the die.

Lift For Emergency
Ratchet Release

INSTRUCTION

MANUAL NUMBER

78-6900-1917-5

34-7033-9144-0

78-6900-1806-0
78-8073-7530-4
78-8073-7529-6

80-6106-2571-9

Required)

34-7031-4262-9

5. Close the jaws completely to exactly align the
dies. Then secure them in place by tightening the
thumb screws.

6. Follow mounting procedures outlined in the
appropriate connector instruction manual. See
listing at right.

"ST*" is a trademark of AT&T

Important Notice

All statements, technical information and recommendations
related to the Seller's products are based on information believed
to be reliable, but the accuracy or completeness thereof is not
guaranteed. Before utilizing the product, the user should
determine the suitability of the product for its intended use. The
user assumes all risks and liability whatsoever in connection with
such use.

Any statements or recommendations of the Seller which are not
contained in the Seller's current publications shall have no force
or effect unless contained in an agreement signed by an
authorized officer of the Seller. The statements contained herein

3M Telecom Systems

6801 River Place Blvd.
Austin, TX 78726-9000
800/426-8688

Note: The crimp rings for the ST Push Pull

Connector have been improved over the
ones used in the manuals listed above. To
obtain a new die to fit previous ST Push Pull
crimp tools, please call customer service.

are made in lieu of all warranties, express or implied, including
but not limited to the implied warranties of merchantability and
fitness for a particular purpose which warranties are hereby
expressly disclaimed.

SELLER SHALL NOT BE LIABLE TO THE USER OR ANY
OTHER PERSON UNDER ANY LEGAL THEORY, INCLUDING
BUT NOT LIMITED TO NEGLIGENCE OR STRICT LIABILITY,
FOR ANY INJURY OR FOR ANY DIRECT OR
CONSEQUENTIAL DAMAGES SUSTAINED OR INCURRED BY
REASON OF THE USE OF ANY OF THE SELLER'S
PRODUCTS THAT WERE DEFECTIVE.

34-7034-5908-0

Printed in USA

© 3M 1993