Beko 2112 CX User Manual
Specifications of your
Washing Machine |
Things to do Before Calling the Authorized Service
Removing the packaging reinforcements 7
Removing the transportation safety bolts 7
Adjusting the feet
Control Panel 10
and Operating Your
Machine | 10
Program selection table
Changing the Program
Cancelling a program
Laundry Addition Function
End of the Program
Unloading the Laundries
Inlet Water Filters
Maintenance and cleaning | 14
Cleaning the pump filter 14
Your Washing Machine
Specifications of your Washing Machine |
Maximum dry laundry capacity (kg)
In order to improve the product quality, modifications can be made in the specifications without prior notice.
The illustrations in this guide are schematic and may not exactly match with your product.
The values that are declared in the markings on your product or in the printed documents accompanying are obtained in a laboratory environment according to the related standards. These values may vary according to the usage of the product and environmental conditions.
•This product is designed for household usage.
•Your washing machine is adjusted to 230 volts. Your machine may not operate with low voltage.
•If the current value of the fuse at your home is less then 16 amperes, consult a qualified electrician and have a fuse of 16 amperes installed.
•When using with or without a transformer, make sure that the grounding installation is made by a qualified electrician. When used without grounding, our company shall not be responsible for the possible damages.
•In order to make your machine ready to use, call Authorized Service and if your clean water installation and water drains are not proper, call a qualified plumber.
•Your machine should not be placed on a rug covered floor. Otherwise, electrical parts may overheat since your machine will not be able to take air from the bottom. This may lead to the machine malfunction.
•While installing the machine, make sure that the hot and cold water taps are connected correctly. Otherwise, your laundries may come out hot in the end of washing process and worn out.
•When the supply cord/plug of the machine is damaged, you must call the authorized service.
•Make sure that the water inlet hoses are new. Do not use worn out/used water inlet hoses again. It may cause stains to remain on your laundries.
•Before washing the clothes that are pretreated with cleaning agents (gasoline ether, liquid stain remover and etc.) rinse thoroughly with clean water.
•Never wash the device with a water hose! There is a risk of electric shock! Before cleaning, always disconnect the electricity connection by unplugging.
•Never touch the plug with wet hands.
Never grab from the cable but from the plug when unplugging.
•If the power cable or the plug is damaged, or the appliance shows any other errors, do not operate the appliance!
•For the failures that can not be solved by applying the information given in these operating instructions:
Turn off the machine, unplug it, close the water tap and contact with the customer service center. Never try to repair the machine by yourself.
•When you operate your washing machine for the first time, use Cotton 90o program with detergent without loading the machine with laundry in order to make it ready for washing your laundry. After washing the very dirty clothes such as the working clothes of a car technician, it is recommended to repeat the machine cleaning process.
•The performance of your washing machine depends on the compound effect of the machine, water and the cleaning agent that is used. If poor and unqualified cleaning agents are used, stains on your laundries will be stabilized. Before washing the stained
laundries, pay attention to clean them as described in the following pages.
•Your machine is designed to resume
its operation when the power restores after a power failure. You can not cancel the program by pressing On/Off button. When the power restores, the machine will resume from the point it stopped.
•During the production, some water may have remained in your machine because of the quality control processes. It does not cause any damage to your machine.
•Plug must be accessible after installation.
•The repair or change of main plug should be carried out by authorized technicians or specialists.
•Main water pressure should be between
1 - 10 bars.
Things to do Before Calling the Authorized Service
If the light of the 1st auxiliary function
It is in the
on the left hand side is flashing
If the cover and washing light on the
The program selection knob may be
Readjust the program by turning the program
flashing and the end light is
selection knob. If the warning continues, contact the
If the light of Start/Pause/Cancel
The door may not be properly closed. Open and
button starts to flashing after a short
close the door again and restart the washing pro-
time you start your machine
The water may be cut or the taps may be closed.
If the “Washing” light on the program
Check the taps. Turn off your machine and restart.
If the fault persists, unplug your machine, close the
taps and contact the authorized service.
Machine may be in the
substructure problems (grid voltage, water pressure and
If the program can not be started or
Therefore, you can not start or select a program. Press
Start/Pause/Cancel button for 3 seconds and return
the machine to the factory settings. (See.Cancelling a
If the water is cut while your machine
Press “Start/Pause/Cancel” button, program will
is operating, the current program does
not proceed. To continue the program
Your machine may stop due to the low
Wait for a while. When the voltage reaches to a nor-
mal level your machine will start to operate.
During the production, some water
may have remained in your machine
This does not cause any damage to your machine.
because of the quality control
You have selected the program in your
The plug of your machine may not be plugged in a
machine and pressed the “Start/
grounded outlet, front cover may not be closed or
Pause/Cancel” button but the machine
the fuse may be blown.
did not start
Check the water inlet and drainage hoses. Are they
Is water coming from under your
well mounted? Gaskets of the water inlet hoses may
not be well seated. If the problem is none of them,
the pump filter may not be well closed.
Is the water drained directly?
Check if the drainage hose is connected as
described in the user guide.
During the water drainage, you may
This sound is normal.
hear water sound from the pump
Is foam running over the detergent
Check if your detergent is suitable for automatic
machine. Use the recommended amount of
detergent in your next washing.
If sometimes you are not satisfied with
Make sure that you have selected the correct
the rinsing and spinning
program, you have adjusted the speed adjusting/
efficiency (laundries have
decrease button correctly and you have loaded the
detergent remnants or they are not dry
right laundries for the program you have chosen, try
again when the voltage is normal.
Removing the packaging reinforcements
To remove the packaging reinforcement lean the machine backward, take the reinforcement by pulling from the braid.
Removing the transportation safety bolts
Before operating the machine, the transportation safety bolts must definitely be removed. For this,
1.Loosen the bolts thoroughly by turning them anticlockwise with the help of a suitable wrench.
2.Pull off the transportation safety bolts.
3.Insert the plastic caps in the direction of arrow into the holes from where the transportation safety bolts are removed.
Please note! Keep the transportation safety bolts in a safe place in order to reuse them for any other transportation. Transport your washing machine with the transportation safety blots installed.
Adjusting the feet
Your machine must stand level and balanced on its feet in order to operate more silent and
First loosed the plastic counter nut on the adjustable feet of your machine.
After maintaining the balance by adjusting the feet, tighten the plastic counter nut upwards.
a) Water inlet hose
The specific hoses that come with the machine are connected to the water inlet valves on the machine. Red labeled hose is for hot water inlet and blue labeled hose is for cold water inlet.
"If you are going to use your double waterinlet machine as a single (cold)
If you want to use both water inlets of the product, you can connect the hot water hose after removing the stopper and gasket group from the hot water valve.
* Applies for the products supplied with a blind stopper group. "
Since the connection points are under water pressure, turn on the taps to the maximum after the connection. Check if there is any water leakage at the connection points. In order to prevent the water leakages and the damages they may cause, keep the taps closed when you are not using the machine.
Minimum 1 bar and maximum 10 bars of water flow from the tap is enough for your machine to operate efficiently. (In practice, 1 bar means that more than 8 liters of water per minute flows from a full open tap.)
Install the elbowed end of the hose to your machine.
Models with double water inlets can be used as a model with a single water inlet by using a plug. Plug should be installed to the hot water valve. A rubber gasket should be used in order to prevent water leakage from the connection point.
Do not connect the product with single water inlet to the hot water tap. The product may switch to the protection mode if the temperature of the water connected to a product with double water inlet through a Y part and single water inlet is above
a) Water drainage hose
Water drainage hose can be attached to the side wall of a sink or bathtub. Hose should not be bend. When the drainage hose is hanged on a sink or bathtub, it can be secured with a hose bracket so that it will not fall.
The end of drainage hose can be connected directly to the waste water drainage hole or to the specific end that is installed to the outlet elbow of the sink.
The hose should be installed to a height of 40 cm minimum and 100 cm maximum.
0 10 20 30 40 50 60 70 80 90 100 110
Plug in the grounded plug at the end of the power cable of the washing machine to a grounded wall outlet which is fed with suitable voltage and current.
•Please note the followings before start ing to wash your laundry:
-Have you plugged the machine?
-Have you connected the drainage hose as necessary?
-Have you closed the front door?
-Have you opened the tap?
•If you are installing your machine by yourself, please read the “Installation” section first.
•Separation of the laundries to be washed:
Please separate the laundries according to their types (cotton, linen, synthetic, woolen, etc.), dirtiness levels and washing temperature. Do not wash the white clothes along with the colored ones.
Remove solid objects such as belts, cuff links and curtain rods from the laundries or put them into a washing bag.
Empty the pockets. Zip and button up. It is recommended to place the very small laundries such as baby clothes into the big laundries such as pillowcases or put into a special
washing filet in order to prevent them from sticking between the bellows or slipping into the cauldron, pump filter, hose and etc.
For stained laundries, see the Practical and useful information section. Your machine can wash the woolen clothes with a “Machine Washable” or “Unfeltable” label in the special woolen program without damaging them. Sensitive clothes with a “Do not wash in the machine” or
•To open the front door, grab the handle and pull it. For your safety, the front door of your machine can only be opened when the machine is not operating. If the “ready” LED is on, the door can be opened.
•Loading the laundry into the machine:Place the laundries by spreading and
without compaction. Place your hand woven clothes into the machine by turning inside out. When closing the door, make sure that no laundry is in between the door and the rubber bellows.
Push the front door to close it. If the front door is not closed correctly, washing does not start.
• The selection of detergent and softener:
The detergent amount depends on the hardness of water, the amount of laundry and the dirtiness level of the laundry. Recommended amounts are written on the detergent package. If your laundries are not very dirty and/or your water has a low
hardness, use less detergent as recommended in the detergent packages. Otherwise you may encounter excessive foam.
You should use detergents that are developed especially for automatic washing machines. Avoid using bleachers that contain chlorine or sulfur.
Put the powder detergent and softener into the appropriate compartments in the detergent drawer and close the detergent drawer.
Pour the softener as recommended in the package (generally <100ml; i.e. 1 tea cup) Never exceed the “MAX” marking. If you put more, it will mix into the washing water
via siphon (III) and it will be wasted. In this case, it may be necessary to refill the softener. If the softener is condensed over time, it may be necessary to dilute with some water. Otherwise, condensed softener clog the siphon and block the flow.
I. Compartment I, the powder detergent compartment for prewash.
II. Compartment II, the powder detergent compartment for main washing. III.Siphon
The softener compartment.
Program Selection and Operating Your Machine |
Program selection knob
On / Off button
Spin speed selection knob
Auxiliary function buttons
You can make the machine ready for program selection by pressing the “On /off” button. When “On/Off” button is pressed, “Door” LED is on meaning that
“door can be opened”. To turn off the machine, press the “On/Off” button again.
Pressing the “On/Off” button never means that the program is started.