ZyXEL Communications P-660HWP-D1 User Manual

P-660HWP-Dx

802.11g HomePlug AV ADSL2+ Gateway

Quick Start Guide

Version 3.40
7/2007
Edition 1

Copyright © 2007. All rights reserved.

P-660HWP-Dx Quick Start Guide

Overview

The P-660HWP-Dx is a gateway which combines high-speed ADSL Internet access, a
built-in switch, a firewall, and HomePlug AV and high-speed wireless networking
capability.

The figure below shows the P-660HWP-Dx connecting devices via a firewalled DSL
connection to the Internet through:

• standard electrical wiring and HomePlug AV adapters (“A”)

• wireless

• direct, wired connections using the P-660HWP-Dx’s built-in switch.

The P-660HWP-Dx is also a firewall, providing greater security for your local network(s).

This Quick Start Guide shows you the most common settings for connecting to the
Internet, configuring your wireless settings and setting up your HomePlug AV network.

For more information on all features see your User’s Guide on the CD that came in the
package.

To read the User’s Guide insert the CD that came in the box into your CD-ROM drive. A
screen should pop up. Navigate to the User’s Guide from this screen. If a screen does not
pop up, open Windows Explorer (click My Computer), click on the CD-ROM drive (usually
drive D:) and navigate to it from there.

1

P-660HWP-Dx Quick Start Guide

1 Hardware Connections

1DSL: Use the gray telephone wire to connect your P-660HWP-Dx’s DSL port to a

telephone jack (or to the modem port on a splitter if you are using one).

2ETHERNET: Use the yellow Ethernet cable to connect a computer to an ETHERNET

port on the P-660HWP-Dx for initial configuration and/or Internet access.

3POWER: Use only the power cable that came in the package to connect your P-

660HWP-Dx to a power outlet. Make sure the power outlet is switched on. This socket
will also act as your HomePlug AV connection.

4 Push in the POWER button.

5 Look at the lights on the front panel.

•The POWER light (LED) blinks while your P-660HWP-Dx starts up and stays on once it is
ready.

•The ETHERNET, WLAN, DSL, INTERNET and POWERLINE LEDs turn on if the corre-
sponding connections are properly made.

V Check your connections if an LED does not turn on. Then turn the P-

660HWP-Dx off, wait for a few seconds and turn it back on. See

Troubleshooting. If the problem remains, contact your local vendor.

2 Internet Connection Setup: Automatic

Use this section to have your P-660HWP-Dx automatically detect and set up your Internet
connection.

2

P-660HWP-Dx Quick Start Guide

1 Open a browser such as Internet Explorer and go to your favorite website. Wait while

your P-660HWP-Dx tries to detect your DSL connection to your ISP. This may take a
few minutes.

2 After it detects the connection, the DSL light shows green on your device and the

Internet light comes on when the Internet is ready for you to use. If you have a PPPoE
connection, you will have to enter your user name and password.

3 Go to section 3 if you wish to configure your wireless settings using the wizard.

4 If you do not see the connection test screen, or the connection test is not successful,

follow the instructions in the screen below, or check your connections and restart the P­660HWP-Dx.

3 Internet and Wireless Setup Wizard

Use this wizard to connect to the Internet and configure your wireless settings

3.1 Log In to the Wizard

Default Login Information

IP address http://192.168.1.1

administrator password 1234

1 Open a browser such as Internet Explorer and enter the following URL address: http://

192.168.1.1

2 Type the admin password 1234 (default). Click Login.

• If your browser does not display the login screen, see Troubleshooting for details.

3 Type (and retype) a new password and click Apply. It is strongly recommended that

you change the P-660HWP-Dx’s password and write it down.

You have to use a new password other than the default password 1234.

3