ZyXEL PLA4101, PLA4111, PLA4201, PLA4201 v2, PLA5205 User Manual

...

Download

Page 1

PLA Series

Powerline Ethernet Adapters

PLA4101, PLA4111, PLA4201, PLA4201 v2, PLA5205, PLA5215, PLA5206, PLA5405, PLA5256, PLA5456, PLA5206 v2

Utility Version 7.0.2 Edition 6, 05/2016 Default Network Name: HomePlugAV

Quick Start Guide

Use r’s Guide

www.zyxel.com

Page 2

IMPORTANT!

READ CAREFULLY BEFORE USE.

KEEP THIS GUIDE FOR FUTURE REFERENCE.

Note: This guide is a reference for a series of products. Therefore some features or

options in this guide may not be available in your product.

Screenshots and graphics in this book may differ slightly from your product due to differences in your product firmware or your computer operating system. Every effort has been made to ensure that the information in this manual is accurate.

User’s Guide

Page 6

1.1 Overview

This chapter introduces the main applications and features of your ZyXEL HomePlug AV compliant powerline adapter, which is called “PLA” in this guide. The following generic icon is used to represent all PLA models.

In this User’s Guide the electrical wiring network is referred to as the “powerline network”. The HomePlug AV standard specifies how network devices communicate using standard electrical wiring.

CHAPTER 1

Introducing the PLA

This User’s Guide covers the following models:

Table 1 PLA Comparison Table 1

PORT/FEATURE PLA4101 PLA4111 PLA4201 PLA4201 v2 PLA5205 PLA5215

10/100 Base-T Ethernet port(s)

Gigabit Ethernet port(s)

AC Pass-Through Reset/Encrypt Button Reset Button Encrypt Button Maximum PHY Rate

over Powerline

Table 2 PLA Comparison Table 2

PORT/FEATURE PLA5206 PLA5405 PLA5256 PLA5456 PLA5206 v2

10/100 Base-T Ethernet port(s)

Gigabit Ethernet port(s)

AC Pass-Through Reset/Encrypt Button Reset Button Encrypt Button Maximum PHY Rate

over Powerline

200 Mbps 200 Mbps 500 Mbps 600 Mbps 600 Mbps 600 Mbps

11222

1000 Mbps 1200 Mbps 1000 Mbps 1800 Mbps 1000 Mbps

PLA Series User’s Guide

Page 7

Note: In this guide RESET/ EN CRY P T refers to the EN CRY PT button in PLAs that have

You can directly plug an electrical device (such as a router or computer) into PLAs with an AC power pass-through socket to supply power to the device.

There are two types of hardware for each of the PLA4101 and PLA4201 v2 models:

• One has an Ethernet port on the top and a power plug at the bottom of the rear panel.

• One has an Ethernet port on the bottom and a power plug at the top of the rear panel.

The power plug varies depending on your region.

1.2 LEDs

The following sections describes the lights on the PLA.

The following figure is the front panel of the PLA. Use the lights to determine if the PLA is behaving normally or if there are some problems on your powerline network.

Chapter 1 Introducing the PLA

separate RESET and EN CRYPT buttons.

Figure 1 PLA Lights

The following table describes the behavior of the lights on the PLA.

Table 3 LEDs: 200 Mbps Models

LIGHTS ICON COLOR STATUS DESCRIPTION

POWER Green On The PLA is on and receiving power.

It also indicates a successful connection using the RESET / EN CRYPT button.

Blinking It indicates the PLA is trying to connect with another device

using the ENCRYPT function.

The Po w er LED blinks when it is in standby mode. Refer to

Section 1.3 on page 9 for details on this feature.

Off The PLA is not receiving power.

PLA Series User’s Guide

Page 8

Chapter 1 Introducing the PLA

Table 3 LEDs: 200 Mbps Models (continued)

LIGHTS ICON COLOR STATUS DESCRIPTION

HomePlug Green On The PLA detects another powerline adapter. The data transfer

rate is greater than 40 Mbps.

Amber The PLA detects another powerline adapter. The data transfer

rate is between 12~40 Mbps.

Red The PLA detects another powerline adapter. The data transfer

Green/ Amber/ Red

ETHERNET Green On The ETHERNET port is on and ready and the PLA detects a

Blinking The PLA is communicating with another powerline adapter.

Off The HomePlug port does not detect another powerline

Blinking The PLA is communicating with a networking device

Off The PLA does not detect any devices connected to its

rate is between 0~12 Mbps.

Data is being transmitted and/or received.

adapter.

device connected to it.

connected to it.

ETHERNET port.

Table 4 LEDs: 500 / 600 / 1000 / 1200 / 1800 Mbps Models

LIGHTS ICON COLOR STATUS DESCRIPTION

POWER Green On The PLA is on and receiving power.

It also indicates a successful connection using the RESET / EN CRYPT button.

Blinking It indicates the PLA is trying to connect with another device

using the ENCRYPT function.

The Po w er LED blinks when it is in standby mode. Refer to

Section 1.3 on page 9 for details on this feature.

Off The PLA is not receiving power.

HomePlug Green On The PLA detects another powerline adapter. The data transfer

rate is greater than 80 Mbps.

Amber The PLA detects another powerline adapter. The data transfer

Red The PLA detects another powerline adapter. The data transfer

Green/ Amber/ Red

ETHERNET Green On The ETHERNET port is on and ready and the PLA detects a

Blinking The PLA is communicating with another powerline adapter.

Off The HomePlug port does not detect another powerline

Blinking The PLA is communicating with a networking device

Off The PLA does not detect any devices connected to its

rate is between 20~80 Mbps.

rate is between 0~20 Mbps.

Data is being transmitted and/or received.

adapter.

device connected to it.

connected to it.

ETHERNET port.

PLA Series User’s Guide

Page 9

Chapter 1 Introducing the PLA

1.3 Standby Mode (Power Saving Mode)

Your PLA is a certified green product. It goes into standby mode when there is no Ethernet connection.

When you plug the PLA into an electric socket, it waits for an Ethernet connection. When no connection is detected after three minutes, the Power LED blinks indicating that it is going into standby mode.

The same process occurs when you disconnect the PLA from a previously working Ethernet connection. Three minutes after disconnecting the Ethernet cable, the PLA’s power LED blinks signalling that it is going into standby mode.

The Ethernet and HomePlug LEDs are turned off in standby mode.

While in standby mode, you cannot use the RESET/ EN CRYPT button. To enable the RESET/ EN CR YPT button again, you have to connect the PLA’s Ethernet cable to a computer/notebook or modem/router first. The PLA wakes up from standby mode and you can start using the RESET/

EN CR YPT button.

1.4 Ways to Manage the PLA

Use the RESET/ EN CRYPT button to add powerline devices to your powerline network if they have this button. See

Use the ZyXEL P LA Se ri e s Co n f igu r a tion utility (or utility, for short) to manage the PLA. See

Chapter 3 on page 19 for instructions on installing the utility.

Chapter 2 on page 12 for instructions on using the ENCRYPT feature.

1.5 Expand Your Network with the PLA

The PLA plugs into an ordinary power outlet to easily extend a cable or DSL broadband connection or existing Ethernet (LAN) network to any other electrical outlet in any room of a house, all without the need for any new cabling. Devices can securely communicate with each other at high data transfer rates. The PLA uses 128-bit Advanced Encryption Standard (AES) to ensure safe transfer of information.

PLA Series User’s Guide

Page 10

Chapter 1 Introducing the PLA

PLA

Figure 2 Expand Your Network with the PLA

Connect your PLA to an Internet gateway such as a modem and plug it into an ordinary power outlet in your home. Plug a second PLA into another power outlet and connect a computer to the PLA for Internet access. Your network can be further expanded by plugging additional PLAs into other outlets in your home and connecting other computers or network devices (for example, a printer) to them.

Refer to your Quick Start Guide for hardware connection information.

1.6 Security

Since your powerline network may extend outside your premises, it is important to set up security on your PLA.

1.6.1 Passwords

You use two types of passwords in the HomePlug AV powerline network. The following table describes the differences between the passwords.

Table 5 Password Summary

PASSWORD DESCRIPTION

Network Name All powerline adapters that follow the HomePlug AV standard are shipped with the

DAK (Data Access Key) Password

same powerline network name “HomePlugAV”. Change the network name via the Zy XEL PLA Se r i e s Co n f igu r a t ion utility or RESET/ ENCRYP T button to create a private network. See

In order to manage the powerline adapters on your powerline network you must enter the adapters’ DAK password in the ZyXEL PLA Ser ie s Co n f igur a t ion utility. This password is printed on the powerline adapter itself.

Section 4.4 on page 32.

You don’t need to add the password for the powerline adapter directly connected to the computer running the configuration utility (local powerline adapter), you only have to add the remote powerline adapters’ passwords (those on your circuit, but not directly connected to your computer).

PLA Series User’s Guide

Page 11

1.6.2 Setting Up Security

The ENCRYPT feature automatically sets up security on your powerline network. Use this feature if your powerline devices have the RESET/ EN CRYPT button.

Alternatively, use the ZyXEL PLA Se rie s Configura t ion utility to set up security on the PLA. Although the PLA is a “plug-and-play” network expanding solution there are several reasons for enabling security on the powerline network in your home.

1 It’s easy and only requires you to change a network name.

2 It’s a good idea to ensure privacy of your communication. When you use the PLA and other

powerline adapters, the electrical wiring in your home becomes an extension of your Ethernet network. Your network traffic flows freely within the electrical circuit of your home and is bounded in most cases by a power meter.

Without security (encryption) your information is accessible to anyone using a powerline adapter on the same electrical circuit. In some cases, a circuit can be shared by more than one household.

To prevent compromising your network security, you can create a private network. A private network uses a secret password (Ne t w or k N am e) to make sure that only permitted powerline adapters can communicate in your network. See up a private network.

Chapter 1 Introducing the PLA

Section 4.4 on page 32 for information on setting

3 You may need to change the Ne tw or k N am e to create multiple powerline networks. See the next

section for more information on how to set up a multiple network.

1.7 Multiple Networks

Multiple powerline networks can coexist on a single powerline circuit. You might want to implement multiple powerline networks in a small office environment where you have two separate Ethernet networks.

1 Connect one powerline adapter to a router or switch on the first Ethernet network and assign a

N e t w or k N am e (for example “Password1”) to this powerline adapter. Add additional powerline

adapters to your network by plugging them into your powerline outlets and assigning them “Password1”. This completes the configuration of your first powerline network.

2 Connect another powerline adapter to a router or switch on the second Ethernet network and

assign a different Ne t w o r k N am e (for example “Password2”) to this powerline adapter. Again, add additional powerline adapters and assign them “Password2”.

You now have two private networks on your powerline circuit. Information is not shared between the two networks as only powerline adapters with the same Ne t w o r k N am e can communicate with each other.

PLA Series User’s Guide

Page 12

CHAPTER 2

The RESET/ENCRYPT Button

Use the RESET/ ENCRYP T button to automatically set up a secure powerline connection between your powerline devices.

Note: In this guide RESET/ EN CRY P T refers to the EN CRY PT button in PLAs that have

separate RESET and EN CRYPT buttons.

2.1 RESET/ENCRYPT Button Overview

The RESET / EN CRYPT button allows you to set up a secure powerline connection with other HomePlug AV compliant powerline devices which also support the ENCRYPT feature. No other powerline setting changes are required to connect.

You can use the RESET / EN CR Y PT button to:

• set up a new powerline network.

• separate an existing powerline network into multiple networks.

• reset the PLA to the factory defaults.

2.2 Adding Devices to a Powerline Network

You can connect a number of PLAs on a powerline network, but you can use the RESET/ ENCRYPT button on only two PLAs at a time.

Place a powerline device close to another powerline device so you have time to set up each one. After you set up the first powerline device, you have 120 seconds to set up the second powerline device.

Note: Your PLA must be connected to a networking equipment for the RESET/ EN CRYPT

button to work. Refer to

Follow the steps below to set up your HomePlug AV Network:

1 Press the RESET / EN CRYPT button at the side of your powerline device for 0.5 to 3 seconds. The

power ( ) light will blink as the powerline device tries to set up a connection with a new random network name.

Section 1.3 on page 9 for more details.

PLA Series User’s Guide

Page 13

Chapter 2 The RESET/ENCRYPT Button

press 0.5 ~ 3 seconds

within 2

minutes

PLA PLA

Figure 3 ENCRYPT Connection Procedure

Note: The RESET/ EN CRYPT button’s location varies for each Powerline model.

Note: Check the lights on the two powerline devices. The power ( ) and HomePlug ( )

lights should be on while the devices are connecting. Wait for about two minutes while your powerline devices connect.

If the power ( ) light does not blink when you press RESET/ EN CRYPT, you have probably pressed the RESET/ EN CRYPT button for too long. Try again, pressing the RESET/ EN CRYPT button for 0.5 to 3 seconds.

If the HomePlug ( ) lights on both powerline devices do not light up, the powerline devices are not connected. Repeat step 1 in this section. If that doesn’t work, see the Troubleshooting in Section 6.4 on page 48 for suggestions.

2 To add more powerline devices to your network, use any powerline device (A or B) you have

connected to set up a connection with the powerline devices you want to connect (C and D).

3 Press the RESET / EN CRYPT button on both powerline devices (A and C, or B and C) for 0.5 to 3

seconds to add powerline device C. This must be done within 2 minutes (120 seconds) of pressing the RESET / EN CRY PT button on the PLA.

4 Press the RESET / EN CRYPT button on both powerline devices (A and D, B and D or C and D ) for

0.5 to 3 seconds to add powerline device D. This must be done within 2 minutes (120 seconds) of

pressing the RESET/ EN CRYPT button on the PLA.

PLA Series User’s Guide

Page 14

Chapter 2 The RESET/ENCRYPT Button

A OR B

A OR B OR C

Figure 4 Adding More Powerline Adapters to Your Network

This sets up your powerline network between your powerline devices.

2.3 Removing a Device from a Powerline Network

Suppose you want to remove PLAs (C) and (D ) from the following powerline network.

Figure 5 Removing Devices From an Existing Powerline Network

1 Press the RESET / EN CRYPT button on powerline device C for 5 to 8 seconds and then release it.

This disconnects C from the current network.

2 Press the RESET / EN CRYPT button on powerline device D for 5 to 8 seconds and then release it.

This disconnects D from the current network.

PLA Series User’s Guide

Page 15

Chapter 2 The RESET/ENCRYPT Button

2.4 Multiple Separate Powerline Networks

You can use the RESET / EN CRYPT button to create multiple separate powerline networks. Use the RESET / EN CRYPT button on only two PLAs at a time.

1 Press the RESET / EN CRYPT button on powerline devices E and F for 0.5 to 3 seconds. This must

be done within 2 minutes (120 seconds) of pressing the RESET/ EN CRYPT button on the first PLA.

2 Wait for about one minute while powerline devices E and F connect.

3 Now pair two different PLAs. Press the RESET/ EN CRYPT button on powerline devices G and H for

0.5 to 3 seconds and within two minutes of each other.

4 Wait for about one minute while powerline devices G and H connect.

5 When the power ( ) and HomePlug ( ) lights shine steadily, the devices are connected.

Figure 6 Two Separate Powerline Networks

If the HomePlug ( ) lights on both powerline devices do not light up, the powerline devices are not connected. Repeat the connection process, making certain you press the RESET / EN CRYPT buttons for the correct time and within two minutes of each other. If that does not work see Section 6.4 on page 48 for suggestions.

2.5 PLAs With One Combination RESET/ENCRYPT Button

Refer to Table 1 on page 6 to see which models have a combination RESET / EN CRYPT button.

PLA Series User’s Guide

Page 16

Chapter 2 The RESET/ENCRYPT Button

The following table summarizes the actions that occur when the RESET/ EN CR YPT button is pressed for specific lengths of time.

Table 6 RESET/ EN CRYPT

TIME ACTION POWER LIGHT BEHAVIOR

0.5 to 3 seconds

5 to 8 seconds

10 to 15 seconds

Create a powerline network with a new random network name.

Join an existing powerline network by sharing the same network name as other devices on the network.

Remove the device from any network it is associated with and its network name assumes a random value.

Clear all user-entered configuration information and return the device to its factory defaults.

The power ( ) light blinks until the device is connected. This may take a minute.

The power ( ) light blinks and then shines steadily.

HOMEPLUG LIGHT BEHAVIOR

The HomePlug ( ) light turns on if your device is connected to another powerline device or a powerline network.

The HomePlug ( ) light turns off when it disconnects from the powerline network.

Note: The network name is unknown when you use the RESET/ EN CRYPT button.

2.6 PLAs with Separate RESET and ENCRYPT Buttons

Refer to

2.6.1 ENCRYPT Button Behavior

The following table summarizes the actions that occur when the ENCRY PT button is pressed for specific lengths of time.

Table 7 EN CRYPT

TIME ACTION POWER LIGHT BEHAVIOR

less than 3 seconds

more than 10 seconds

Table 1 on page 6 to see which models have separate RESET and EN CRYPT buttons.

HOMEPLUG LIGHT BEHAVIOR

Create a powerline network with a new random network name.

Join an existing powerline network by sharing the same network name as other devices on the network.

Remove the device from any network it is associated with and its network name assumes a random value.

The power ( ) light blinks until the device is connected. This may take a minute.

The power ( ) light blinks and then shines steadily.

The HomePlug ( ) light turns on if your device is connected to another powerline device or a powerline network.

The HomePlug ( ) light blinks red one time and then turns off when it disconnects from the powerline network.

PLA Series User’s Guide

Page 17

Chapter 2 The RESET/ENCRYPT Button

2.6.2 RESET Button Behavior

Use a pointed device such as a pin to reset the Ne t w or k N am e back to default H om ePlu gAV.

Table 8 RESET Button

TIME ACTION POWER LIGHT BEHAVIOR

1 to 3 seconds

Clear all user-entered configuration information and return the device to its factory defaults.

The power ( ) light blinks and then shines steadily.

HOMEPLUG LIGHT BEHAVIOR

The HomePlug ( ) light turns off when it disconnects from the powerline network.

See Troubleshooting in

Chapter 6 on page 48 for suggestions on problems with the RESET /

EN CR YPT button and the lights.

PLA Series User’s Guide

Page 18

PART II

Technical Reference

Page 19

This chapter guides you through the installation of the configuration utility for your PLA.

3.1 Windows

This section uses the Windows XP screens as an example to show you how to install the Windows vesion of the ZyXEL PLA Se ri e s Co n f igu r at ion utility.

3.1.1 System Requirements

At the time of writing, the Zy X EL PLA Se r ie s Configu r a tion utility is compatible with:

• Windows XP (32-bit version)

• Windows XP (64-bit version)

• Windows Vista (32-bit version)

• Windows Vista (64-bit version)

• Windows 7 (32-bit version)

• Windows 7 (64-bit version)

• Windows 8 (32-bit version)

• Windows 8 (64-bit version)

CHAPTER 3

Installing the Utility

Note: To check for your Windows operating system version, right-click on My Com pu t er

> Pr op ert ie s. You should see this information in the Gene ral tab.

Microsoft’s .NET Framework version 4 and WinPcap 4.1.3 software are necessary for the installation of the ZyXEL P LA Se rie s Co n fig u r at ion utility. The utility automatically installs WinPcap 4.1.3 and .NET Framework version 4 on all supported operating systems (if it’s not already installed on your computer).

3.1.2 Installing the Utility

Follow the steps below to install WinPcap 4.1.3, .NET Framework version 4 and the ZyX EL P LA Se r ie s Configur a tion utility on your computer.

1 Go to the ZyXEL Download Library and download the utility to your computer. Double click the

utility se t up.ex e file. If WinPcap 4.1.3 is already installed on your computer, the following screen appears. Click Can ce l

and go to step

PLA Series User’s Guide

Page 20

Chapter 3 Installing the Utility

Otherwise, the WinPcap setup wizard runs automatically. Click Ne x t to continue.

2 Review the l ice nse a g r eem ent , and click I Agre e to proceed.

3 Select Au tom at ica lly st art t he W inPca p dr iv e r a t b oot t im e if you want to start WinPcap

automatically when the computer boots. Click I nst a ll to install WinPcap.

PLA Series User’s Guide

Page 21

Chapter 3 Installing the Utility

4 Select I w an t t o m anu a lly re b o o t la t er, and click Fin ish to exit the wizard.

5 A prompt appears asking you to install the .NET Framework version 4. Review Microsoft’s Lice n se

Ag r eem ent , select I ha v e r ea d a n d a cce p t t he lice n se t e rm s. and click I nt a ll to proceed.

Note: If you already have .NET Framework version 4 installed on your computer this step

can be skipped.

PLA Series User’s Guide

Page 22

Chapter 3 Installing the Utility

6 The next screen allows you to see the progress of the installation.

7 Click Fi n i sh to close the window.

PLA Series User’s Guide

Page 23

Chapter 3 Installing the Utility

8 The utility installation wizard runs automatically. Click Ye s or N e xt to continue through the initial

screen. Click Ca ncel only if you want to abort the installation.

9 Click I nst all to install the utility to the default folder.

PLA Series User’s Guide

Page 24

Chapter 3 Installing the Utility

Figure 7 Install Destination Folder

10 The screen shows you the progress of the installation.

Figure 8 Utility Installation Process

11 Click Fin ish to exit the wizard.

PLA Series User’s Guide

Page 25

Chapter 3 Installing the Utility

Figure 9 Installation Complete

Note: You may be asked to restart your computer when the installation is complete. Click

“Yes” to restart your computer. If you select “No, I will restart my computer later”, you will not be able to launch the utility until after a restart of your computer.

3.2 Macintosh (Mac)

This section uses the Mac OS X 10.8 screens as an example to show you how to install the Mac vesion of the ZyXEL PLA Se ri e s Co n f igu r at ion utility.

3.2.1 Supported OSs

At the time of writing, the following Mac operating systems support the ZyX EL PLA Se ri e s Configur a tion utility:

•Mac OS X 10.6

•Mac OS X 10.7

•Mac OS X 10.8

3.2.2 Installing the Utility

Follow the steps below to install the Zy X EL P LA Ser ie s Configu r a tion utility on your Mac computer.

1 Go to the ZyXEL Download Library and download the utility to your computer..

2 Double-click the PLA U t ili t y 1 .0 .0 .m pk g file to run the installation program. When it opens, follow

the on-screen instructions.

PLA Series User’s Guide

Page 26

Chapter 3 Installing the Utility

3 Click I nst all to install the utility to the default folder, or click Chan g e I nsta l l Lo cat i o n . . . to

specify a different location on your computer.

4 When the installation is finished, a screen appears to confirm the PLA Se r ie s Configur a tio n

Ut i lit y has been successfully installed to your computer. Click Close .

PLA Series User’s Guide

Page 27

Chapter 3 Installing the Utility

5 After installing the utility, you can find the utility icon in your Applica t ion s folder.

If you are running Mac OS X 10.7 or later, you can also see the utility icon in the Lau n ch p a d screen.

PLA Series User’s Guide

Page 28

4.1 Overview

PLA

This chapter shows you how to use the Zy X EL P LA Se rie s Co n fig u r ation utility (or utility) to secure, manage and set up Quality of Service (QoS) on your powerline network.

The PLA is designed as a plug-and-play network expanding solution. This means that once you complete your hardware connections, the PLAs in your network (without additional configuration) are able to communicate with each other by sending and receiving information over your home’s electrical wiring (A).

Figure 10 Example Network Setup

CHAPTER 4

The Configuration Utility

All HomePlug AV compliant powerline adapters within range can join your network. The range varies depending on the quality of your home’s wiring.

See

Section 4.1.1 on page 28 for more information on enhancing your powerline network security.

Note: It is recomended to use the ZyXEL PLA Se rie s Conf i g ur at ion with PLA5206

independently.

4.1.1 Powerline Network Security

When the PLAs communicate with each other, they use encryption to protect the information that is sent in the powerline network. Encryption is like a secret code. If you do not know the secret code, you cannot understand the message. The HomePlug AV standard uses 128-bit AES (Advanced Encryption Standard) to safely transmit data between powerline adapters.

PLA Series User’s Guide

Page 29

Chapter 4 The Configuration Utility

For the powerline adapters to communicate with each other they all need to use the same network name. This network name allows the powerline adapters to understand the encrypted information sent in the powerline network.

By default the PLAs are all configured with the network name Hom eP lu g AV, this allows you to simply plug the devices in and not worry about setting up security. If you want to enhance the security on your powerline network, you can change the network name on the powerline adapters you want to allow to communicate in your powerline network.

4.1.2 Device Access Key (DAK)

In order to manage the powerline adapters on your powerline network you must enter the adapters’ password in the ZyXEL P LA Ser i e s Co n fig u r at ion utility. This password is called the DAK (Device Access Key) password. This password is printed on the powerline adapter itself.

You don’t need to enter the DAK password for the powerline adapter directly connected to the computer running the utility (local powerline adapter), you only have to add the remote powerline adapters’ passwords (those in your powerline network, but not directly connected to your computer).

4.2 Starting the Configuration Utility

In Windows, to launch the Zy X EL PLA Se r i e s Co n f igur a tion utility simply double click on the utility icon on your desktop.

Figure 11 ZyXEL PLA Series Configuration Utility Icon (Windows)

Alternatively, start the utility by browsing to it from the start menu. Click St a rt > Pr ogr a m s > ZyXEL P LA Ser i e s Co n figu r at io n > PLA Se ri e s Co n f igu r at io n .

In Mac OS X, open the Applica t ion s folder and double-click the PLA U til it y icon.

Figure 12 ZyXEL PLA Series Configuration Utility Icon (Mac)

4.3 Network Info Screen

Use the N e tw or k I nf o screen to see the rates at which a specific PLA is communicating with other powerline adapters on your powerline network.

PLA Series User’s Guide

Page 30

You can select to view the connection status represented by icons ( ) or view transmission/ receiving rates in a list ( ).

4.3.1 Icon View

Use the up/down arrow or just click a device icon at the left side to select a powerline adapter in your network. The screen shows you the network connection status of the selected device. Click

Re fr esh to update the screen immediately.

Figure 13 Network Info Screen (Icon)

Chapter 4 The Configuration Utility

The connection status icon ( , , or ) indicates the current data rate of the powerline adapter, and is equivalent to the HomePlug LED. See

In this mode, you can click a device’s I nfo button to open a screen, where you can change the device’s descriptive name that displays in this screen and view it’s MAC address and firmware version. The I n f o screen also shows you how fast the selected powerline adapter sent information to or receive information from this device. For example, if the Loca l powerline adapter is selected, a Re m o t e powerline adapter’s I nf o screen also displays the rates of transmission from the powerline adapter connected to the computer running the configuration utility to all the Re m ot e powerline adapters.

PLA Series User’s Guide

Chapter 1 on page 7 for more information.

Page 31

Figure 14 Network Info Screen (Icon) > Info

4.3.2 List View

Figure 15 Network Info Screen (List)

Chapter 4 The Configuration Utility

The following table describes the labels in this screen.

Table 9 Network Info Screen (List)

LABEL DESCRIPTION

Adapter This field identifies which powerline network information is displayed. Different powerline

networks are identified by the Ethernet interface (network card) connected directly to the PLA. Typically there is only one connection, however, if your computer has two network cards and both are connected to a PLA, then you have two powerline networks.

Central Coordinator MAC

The Central Coordinator of the powerline network is the powerline adapter which keeps track of which devices are part of the network as well as synchronizes communication within the powerline network. If the Central Coordinator is removed from the powerline network then another powerline adapter takes its place. This field displays the MAC address of the PLA which is the Central Coordinator of the powerline network. The powerline adapters in your powerline network automatically select the Central Coordinator.

PLA Series User’s Guide

Page 32

Chapter 4 The Configuration Utility

Table 9 Network Info Screen (List) (continued)

LABEL DESCRIPTION

Select a powerline adapter from the drop-down box.

The information provided in the following table reflects transmission rate information about the powerline adapters which communicate in your powerline network.

The powerline adapters listed in this table are all the powerline adapters in your powerline network except the selected powerline adapter. In other words, if the Loca l powerline adapter is selected, then this table will display the rates of transmission from the powerline adapter connected to the computer running the configuration utility to all the Re m ot e powerline adapters.

Site This field displays:

• Loca l , if it is the PLA directly connected to the computer running the configuration utility.

• Re m ot e , if it is a PLA in your powerline network but not directly connected to the computer running the configuration utility.

MAC Address This field displays the MAC address of your powerline adapter. The MAC address of your

powerline adapter can be found by looking at the label on your device. It consists of six pairs of hexadecimal characters (hexadecimal characters are “0-9” and “a-f”). In the case of the PLA, this label is on the bottom of the device.

Tra n s m i t Rate (Mbps)

Receive Rate (Mbps)

This field displays how fast information is sent from the selected powerline adapter to this powerline adapter. The rate is given in the following format: “application data transmission rate / raw data transmission rate”. Application data reflects more accurately how fast devices are transmitting application relevant traffic (for example Internet Protocol (IP) traffic). Raw data refers to the whole payload of the packets transmitted across the powerline network.

This field displays how fast information is received from the selected powerline adapter to this powerline adapter. The rate is given in the following format: “application data transmission rate / raw data transmission rate”. Application data reflects more accurately how fast devices are transmitting application relevant traffic (for example Internet Protocol (IP) traffic). Raw data refers to the whole payload of the packets transmitted across the powerline network.

4.4 Configuration Screen

Use the Conf ig u r at ion screen to see which devices are recognized by your powerline network, to configure your PLA and to set up a secure powerline network by changing the powerline network name. This screen opens up when you launch the utility.

PLA Series User’s Guide

Page 33

Chapter 4 The Configuration Utility

Figure 16 Configuration Screen

The following table describes the labels in this screen.

Table 10 Configuration Screen

LABEL DESCRIPTION

Network Topology

The fields described below are used to identify the powerline adapters recognized on the powerline network. The configuration utility automatically updates this information every 10 seconds.

Use this to select which powerline network information is displayed. Different powerline networks are identified by the Ethernet interface (network card) connected directly to the PLA. Typically there is only one connection, however, if your computer has two network cards and both are connected to a powerline device then you have two powerline networks.

Note: Only devices which share the same network name are displayed in this table.

Site This field displays

• Loca l , if it is identifying the powerline adapter directly connected to the computer running the configuration utility.

• Re m ot e , if it is a powerline adapter in your powerline network but not directly connected to the computer running the configuration utility.

MAC Address This is a read-only field which shows the MAC address of the powerline adapter you are

FW version This is a read-only field which shows the firmware version of the powerline adapter in your

DAK Password This is a read-only field which shows the DAK (Device Access Key) password of the remote

Scan Click Sca n to refresh the information in the table (immediately).

configuring. You can find the MAC address of your PLA displayed on a sticker on the bottom of your device.

network.

powerline adapter.

PLA Series User’s Guide

Page 34

Chapter 4 The Configuration Utility

Table 10 Configuration Screen (continued)

LABEL DESCRIPTION

DAK Password DAK (Device Access Key) password is used to verify that you are authorized to perform

changes on a remote device. You can find the DAK password printed on a sticker on the bottom of your PLA.

Select the remote powerline adapter you want to manage by clicking the MAC address which corresponds to it in the MA C Ad d r ess column. Enter the D AK Passw ord value and click Sa v e .

Note: You must enter the DAK Password value exactly as it is printed on the label (all caps

and with dashes “-”).

Network Name (NMK)

Set NMK to this device

Set NMK to all devices

Write Click this to apply your changes. The new Net w or k N a m e is applied to the selected

The default network name (sometimes called a network password or network membership key (NMK)) of the PLA is “Ho m ePlu gAV”. HomePlug compatible devices use the same network name to recognize and communicate with each other over the powerline network. If you change the network name of one device on the network, it will no longer be recognized as part of that network.

If you change the network name, make sure you change the network name for all of the powerline adapters that you want to be part of your powerline network.

The network name can be from 8 to 64 characters in length, using “A”~”Z”, “a”~”z”, “0”~”9”; spaces are not allowed.

Select this to apply the NMK (entered in the field above) as the network name for the powerline adapter directly connected to the computer running the configuration utility.

Select this to apply the NMK (entered in the field above) as the network name for all powerline adapter detected by the utility.

powerline adapter.

Note: You must enter the correct DAK password for the selected remote powerline adapter

before you can make changes to it.

4.5 Advanced Screen

You can configure the powerline adapters on your network to give priority to network traffic depending on its importance. When you set the priority of a powerline adapter, you set how quickly messages FROM your powerline adapter are sent in your powerline network. Transmissions TO your powerline adapter do not receive any priority.

For example, if you have a file server on your home network to deliver music and movie files to computers in your home, you should set the priority of the powerline adapter connected to this server to Me d i u m. If video traffic is delivered too slowly, quality problems may occur.

On the other hand, a powerline adapter attached to a printer should have a low priority setting since the slow delivery of messages will not affect the print job.

Similarly, if you want to prioritize any downloads from the Internet, set the priority on the powerline adapter attached to your Internet gateway to H ig h .

PLA Series User’s Guide

Page 35

Chapter 4 The Configuration Utility

Allocate priority settings based on application type as follows.

Tabl e 11 Priority Settings

PRIORITY LEVEL APPLICATION

High Voice Application Medium Video and Audio Applications Normal Data Applications Low Data Applications

The figure below shows an example powerline home network connected to the Internet.

• Device A is a printer and does not handle traffic with high importance, so the powerline adapter connected to it can be set to low priority.

• Device B is a file server, delivering audio or movie files to other users on the network. The powerline adapter attached to it should have a medium setting.

• Device C, a home computer which connects to the Internet, can receive a normal priority setting as it usually sends simple requests for data. For example, when you surf the Internet, your computer sends requests to open web pages.

• Device D is a modem attached to the Internet. It should receive a high priority setting if you want faster downloading through your network.

• Although device E receives audio or movie files, it does not send a lot of traffic, so the powerline adaptor attached to it can be set to a low priority.

Figure 17 Priority Settings

Use this screen to configure priority settings for traffic from the powerline adapters on your network.

PLA Series User’s Guide

Page 36

Figure 18 Advanced Screen

Chapter 4 The Configuration Utility

The following table describes the labels in this screen.

Table 12 Advanced Screen

LABEL DESCRIPTION

Adapter This field identifies which powerline network information is displayed. Different powerline

networks are identified by the Ethernet interface (network card) on your computer which is connected directly to a powerline adapter. Typically there is only one connection. However, if your computer has two network cards and both are connected to a powerline adapter, then you have two powerline networks.

Priority Select a priority setting from the drop-down box for traffic FROM your selected device. The

options, in order of importance, are Hig h , M ed ium , Nor ma l and Lo w .

Site This field displays:

• Loca l , if it is the PLA directly connected to the computer running the configuration utility.

• Re m ot e , if it is a powerline adapter in your powerline network but not directly connected to the computer running the configuration utility.

MAC Address This is a read-only field which shows the MAC address of the powerline adapter you are

Standby mode enable

Save Click this to apply your changes. The new Pr iorit y setting is applied to the selected

configuring. You can find the MAC address of your PLA displayed on a sticker on the bottom of your device.

Select On to have the selected powerline adapter(s) go into standby mode when there is no Ethernet connection. Otherwise, select Off to have the adapter(s) never go into standby mode.

powerline adapter.

4.6 About Screen

Use the Ab ou t screen to view information regarding the configuration utility version of the PLA you are connected to. Click the icon in the top right corner of the utility to view the Abou t screen.

PLA Series User’s Guide

Page 37

Chapter 4 The Configuration Utility

Figure 19 About Screen

The following table describes the labels in this screen.

Table 13 About Screen

LABEL DESCRIPTION

Utility version This field displays the software version of the configuration utility. Released This field displays the date when the utility was released. Close Click the button in upper right corner to close the Abo u t window.

PLA Series User’s Guide

Page 38

5.1 Overview

Use this tutorial to expand your existing powerline network.

After setting up your first home powerline network (instructions for that are in the Quick Start Guide for your ZyXEL powerline adapter) you may want to extend the network or create a new one by adding additional powerline adapters. This tutorial shows you the following.

• How to start up your new powerline adapter. You need to do this before you can begin the next sections.

• How to make your existing powerline network bigger by adding new powerline adapters.

• How to make a new network separate from your existing network with new powerline adapters.

• How to make a new, separate powerline network with the powerline adapters you have.

CHAPTER 5

Powerline Network Setup Tutorial

The tutorial uses the Zy X EL P LA Se rie s Co n figu r at io n utility to set up your powerline adapter.

If you haven’t already installed the utility, see Chapter 3 on page 19 for instructions. The utility software is available for download at www.zyxel.com. Navigate to the powerline products section of the ZyXEL website to find this software. Follow the instructions provided by the software to install it on your computer.

See the product specifications in the User’s Guide for a list of hardware and software compatible with the utility.

Note: The PLA in this tutorial is an example only. Your powerline adapter may be

different.

5.2 Important Terms

Network Name The network name allows a powerline adapter to connect with other powerline

DAK Password DAK = Device Access Key.

adapters that have the same network name. It provides security for your powerline network. The network name uses English letters or numbers, from 8 to 64 characters long, with no spaces allowed.

The DAK Password lets you access the powerline adapter. You can find the DAK Password on a label on your powerline device.

PLA Series User’s Guide

Page 39

Chapter 5 Powerline Network Setup Tutorial

PLA

5.3 Accessing Your Powerline Adapter

1 Plug the powerline adapter you want to add to your network into a power socket and, if needed,

switch the power socket on.

Figure 20 Plug Your Powerline Adapter into a Power Socket

2 Connect the powerline adapter to your computer.

3 Use a LAN or Ethernet cable (shown below) to connect the LAN or Ethernet port on your adapter to

the same kind of port on your computer.

Figure 21 Connect Your Powerline Adapter to a Computer

4 Open the ZyXEL P LA Ser i e s Co n figu r at io n utility on your computer. See

for how to launch the utility.

5 You are now ready to extend your powerline network or set up a second network.

•See

Section 5.4 on page 39 to add a new powerline adapter to your network. Section 5.5 on page 41 to set up a second network with your new adapters. Section 5.6 on page 43 to set up a second network with your existing adapters.

5.4 Adding a Powerline Adapter

This section shows you how to add a new powerline adapter to expand your existing network.

The figure below shows the family computer with Internet access on a powerline network. Expand the network by adding a new powerline adapter connected to a printer.

PLA Series User’s Guide

Section 4.2 on page 29

Page 40

Chapter 5 Powerline Network Setup Tutorial

Figure 22 Add a Printer to Your Powerline Network

Note: You do not need to know the network name of the new adapter to add it to your

network.

1 Connect your computer to the powerline adapter you want to add to your network and open the

ZyXEL PLA Se rie s Co n f igu r a tion utility (see

2 Go to the Con figu r at io n screen. On this screen in the Sit e column your new powerline adapter

should appear as Loca l (A). Check the Lo ca l adapter’s MAC address (B). It should match the MAC address listed on the label on the back of your powerline adapter.

Figure 23 Adding a New Adapter

3 Select your adapter by selecting Loca l and type the network name for your existing network in the

N e t w or k N am e field (C).

Section 5.3 on page 39).

PLA Series User’s Guide

Page 41

Chapter 5 Powerline Network Setup Tutorial

Figure 24 Adding an Adapter to an Existing Network

4 Click W rit e and click OK on the pop-up.

Figure 25 Network Name Pop-up

5 Your new adapter will now have the same Ne tw or k N am e as your existing network and so has

now joined your existing network.

6 Connect the adapter to the device you want to add to the network, for example, your Internet

refrigerator in the kitchen.

7 Plug the adapter’s power cord into a power outlet and, if required, switch the power outlet on.

8 Repeat this procedure for all additional powerline adapters that you want to add to your existing or

new powerline network.

5.5 Setting Up a New Network with a New Adapter

This section shows you how to use your new powerline adapters to set up a new powerline network separate to your existing network.

The figure below shows two powerline networks in a house. The first network (1) shows the home computer connected to a printer and access to the Internet. The second network (2) has no Internet access but with a media adapter such as the ZyXEL DMA-1100P you can use your TV to watch movies and play games which are stored on a computer.

PLA Series User’s Guide

Page 42

Chapter 5 Powerline Network Setup Tutorial

Figure 26 Add New Adapters to Make a Second Network

1 Connect your new powerline adapter and open the configuration utility as shown in Section 5.5 on

page 41. The screen shown below appears.

2 Type a Net w or k N a m e that is different from the N e tw or k N a m e for your existing network. Make

sure you use the same new Net w or k N am e for all new adapters you want to add to your new network.

Figure 27 Making a New Network with the New Adapter

3 After you have set up a new network, you are ready to connect each powerline adapter on your new

network to devices, for example, a computer or a games console.

PLA Series User’s Guide

Page 43

Chapter 5 Powerline Network Setup Tutorial

5.6 Splitting a Network into Two Networks

This section shows you how to split your existing network into two networks. This is useful if you want to set up a second powerline network in your home, for example, in your study connecting a laptop and printer. See

To set up your existing powerline network you had to set each powerline adapter with the same network name. To create a second (separate) powerline network, configure the PLAs you want to add to the second network with a new network name.

1 Connect a powerline adapter to your computer and open the Zy X EL P LA Ser i e s Co n figu r at io n

utility (see

2 The utility should open to the configuration tab as shown below. A list of powerline adapters on your

network displays. These adapters all have the same network name as the adapter you are connected to. The adapter you are connected to will appear as Loca l in this table. All others are listed as Re m o t e.

Figure 28 Local/Remote Adapters on a Powerline Network

Section 5.3 on page 39).

Figure 26 on page 42 for an example.

3 To set up a new powerline network, type the D AK Pa ssw or d and change the N e tw ork N am e on

all powerline adapters you wish to add to your network.

• Look for the DAK Passw or d on a label on your powerline adapter. The D AK Pa ssw ord lets you access the adapter.

• Select the Re m o t e adapter you want to add (A) and type the DAK Pa ssw or d in the DA K Pa ssw or d field (B).

• Then type the new network name in the N et w or k N am e field (C).

PLA Series User’s Guide

Page 44

Chapter 5 Powerline Network Setup Tutorial

Figure 29 Adding an Adapter to Your New Network

4 Click Sa ve .

• If you do not type the DAK pa ssw or d or type it incorrectly the following pop-up appears. Click OK and type the D AK Pa ssw or d correctly in the DAK P a ssw or d field.

Figure 30 Incorrect DAK or No DAK

• If you have correctly entered the DAK Pa ssw or d , click OK on the pop-up.

Figure 31 Correct DAK

5 The adapter will disappear from the table of your existing network.

Figure 32 Adapters on Your Existing Network

PLA Series User’s Guide

Page 45

Chapter 5 Powerline Network Setup Tutorial

6 Go back to step

want to add to your new network.

7 Check you have added the adapters correctly by changing the network name for the local adapter.

All adapters with the new Ne t w or k N am e now appear in the list of adapters on your network. These adapters are now part of your new network.

Figure 33 Adapters on a New Powerline Network

• If you want to access any of your new powerline networks using the ZyX EL PLA Se r ie s Configur a tion utility, change the Ne tw ork N am e on your local adapter to the network name for the network you want to access. The adapters on that network will then display in the adapter table, allowing you to select and configure each one.

3 in this section to set the same, new N e t w o r k N am e for all remote adapters you

5.7 Troubleshooting

The HomePlug ( ) LED (light) should light up on your adapter when it successfully connects to other adapters on your network. If it does not, try the following measures.

• Make sure the adapter is plugged in to a power socket and the power socket is turned on.

• Check you have entered the correct network name for your network.

• Check your powerline adapter is connected to the same electrical circuit as other powerline adapters on your network.

PLA Series User’s Guide

Page 46

This chapter offers some suggestions to solve problems you might encounter.

6.1 Power and Light Problems

The PLA does not turn on. None of the lights turn on.

1 Disconnect and re-connect the PLA.

2 Remove the powerline adapter from the outlet. Then connect an electrical device that you know

works into the same power outlet. This checks the status of the power outlet.

CHAPTER 6

Troubleshooting

3 If the problem continues, contact the vendor.

The ETHERNET light does not turn on.

1 Check the hardware connections. See the Quick Start Guide.

2 Inspect your cables for damage. Contact the vendor to replace any damaged cables.

3 Check the Ethernet adapter on your computer and make sure it’s enabled and working properly.

4 If the PLA is connected to an Ethernet switch or router, make sure the device is working correctly,

and that the LAN network is working and configured correctly as well.

The HomePlug light does not turn on.

1 Use the ZyXEL P LA Se ri e s Co n f igu r a tion utility to detect all other HomePlug devices on your

powerline network. Make sure that the network name (sometimes called the network password) is the same on all of your powerline adapters. See Section 4.4 on page 32 for instructions on changing the network name.

2 Check the DAK password and MAC address for all powerline adapters are typed correctly in the

utility. See

Section 4.4 on page 32 for instructions on checking the DAK and MAC address.

PLA Series User’s Guide

Page 47

Chapter 6 Troubleshooting

3 Make sure that all your powerline adapters are HomePlug AV compliant. Check the package it came

in or ask your vendor. This PLA can not detect earlier versions of HomePlug powerline adapters such as HomePlug 1.0 or 1.0.1. (Although they can coexist on the same electrical wiring without interfering with each other.)

4 Make sure that the powerline adapters on your network are all on the same electrical wiring.

Connect another powerline adapter into an outlet close to your PLA’s power outlet. They are probably now on the same electrical wiring. Check the HomePlug ( ) light. If it now lights up your powerline adapter was probably previously on separate electrical wiring. Ask an electrician for more information on the electrical wiring in your building.

5 Make sure that you do not have a power meter between powerline adapters. Powerline signals

cannot pass this.

The POWER and HomePlug light blink at the same time.

• You have pressed the RESET / EN CRYPT button for more than three seconds. Try setting up a connection again, this time pressing the RESET / EN CRYPT buttons on both devices for less than three seconds.

6.2 Configuration Utility Problems

The ZyX EL P LA Se r ie s Config u rat ion utility displays an error during installation.

• Make sure your computer is using the supported operating system. See Section 3.1.1 on page 19 and/or

The ZyX EL P LA Se r ie s Config u rat ion utility does not display all or any of my devices.

• Inspect the LEDs on your PLA and make sure that the ETHERNET and HomePlug LEDs are on or blinking. See

• Check you are using the latest version utility. Earlier version utilities cannot communicate with PLAs using the latest firmware. If you do not have the latest utility, download it from the ZyXEL website.

• If you are running another tool such as the Fir m w ar e D e tect ion Tool, the utility will not detect your local device.

• If your computer has more than one network interface card (NIC), make sure you select the right NIC to which the PLA is connected in the utility’s Configur a tio n screen.

Section 3.2.1 on page 25 for more information.

Section 1.2 on page 7 for troubleshooting LED related problems.

PLA Series User’s Guide

Page 48

Chapter 6 Troubleshooting

6.3 Powerline Problems

The sign a l on m y po w erlin e n et w or k is w ea k.

1 Your powerline adapters may be connected to electrical surge protectors. Connect them to standard

power outlets.

2 Your powerline adapters may be located close to large appliances such as refrigerators or air-

conditioners that cause interference with the powerline signal. Move the adapters further away from such appliances to reduce interference.

3 Your powerline adapters may be placed close to electrical devices such as electrical insect-killers

which produce radio waves. These may interfere with the powerline signals. Move the adapters further away from such electrical devices.

4 Your wiring may be old and/or low quality or with a long wiring path.

6.4 RESET/ENCRYPT Button Problems

This section applies only to PLAs with the RESET/ ENCRYPT button. In this guide RESET/

EN CRYPT refers to the EN CRYPT button in PLAs that have separate RESET and EN CRYPT buttons. Refer to

EN CR YPT buttons.

The HomePlug light is already on, but I haven’t pressed the RESET/ENCRYPT button yet.

Your device has already connected to another powerline device. Press the RESET / EN CRYPT button for 5 to 8 seconds to release the connection.

The POWER light does not blink when I press the RESET/ EN CRYPT button.

• Check the device is on.

• Press the RESET / EN CRYPT button again, making certain you have pressed the button for 0.5 to 3 seconds.

• The POWER light on some powerline devices do not blink as part of the ENCRYPT process. Check your powerline device is a PLA.

• For PLA, you cannot use the RESET/ ENCRYPT button when it is in standby mode. Connect the PLA to a computer/router then try again.

Table 1 on page 6 to see which models have separate RESET and

PLA Series User’s Guide

Page 49

Chapter 6 Troubleshooting

The POWER light blinks two times quickly then pauses, before repeating.

The ENCRYPT process has failed. Press the RESET/ EN CRYPT button on both devices for 5 to 8 seconds, then try to reconnect.

The POWER lights on both devices blink when I press the RESET/ENCRYPT buttons, but the HomePlug light does not turn on.

• Ensure you have pressed the RESET/ ENCRYPT button on both devices.

• Wait for about a minute while the devices set up a connection.

• If that does not work, try again with both devices connected to a power strip next to each other. If they now connect, then the devices were not on the same electrical circuit before.

The POWER lights on both devices blink, then many lights blink and the HomePlug light blinks red.

Do not worry, the connection process is proceeding normally.

The POWER lights on both devices finished blinking, but only one device’s HomePlug light is on.

One device may have connected to a third powerline device. To check device A is connected to device B and not another device, disconnect device B from its power source. Device A’s HomePlug ( ) light will turn off if the connection is with Device B. Press the R ESET/ EN CR YPT button on both devices for 5 to 8 seconds, then try to reconnect, pressing the RESET/ ENCRYPT button for

0.5 to 3 seconds on both devices.

I pressed the RESET/ENCRYPT button for 5 to 8 seconds, but the HomePlug light is still on.

The HomePlug light is on, indicating it is still connected to another powerline device. Try again, pressing the RESET/ EN CRYPT button for 5 to 8 seconds.

PLA Series User’s Guide

Page 50

APPENDIX A

Customer Support

In the event of problems that cannot be solved by using this manual, you should contact your vendor. If you cannot contact your vendor, then contact a ZyXEL office for the region in which you bought the device.

ht tp: / / ww w. zyxel.com / h om epage. shtm l and also

See

htt p : / / ww w . zyx el. com / about _ zyxel/ zyx el_ w or ldwid e.sh t ml for the latest information.

Please have the following information ready when you contact an office.

Required Information

• Product model and serial number.

• Warranty Information.

• Date that you received your device.

• Brief description of the problem and the steps you took to solve it.

Corporate Headquarters (Worldwide)

Taiwa n

• ZyXEL Communications Corporation

• http://www.zyxel.com

Asia

China

• ZyXEL Communications (Shanghai) Corp. ZyXEL Communications (Beijing) Corp. ZyXEL Communications (Tianjin) Corp.

• http://www.zyxel.cn

India

• ZyXEL Technology India Pvt Ltd

• http://www.zyxel.in

Kazakhstan

•ZyXEL Kazakhstan

PLA Series User’s Guide

Page 51

• http://www.zyxel.kz

Korea

• ZyXEL Korea Corp.

• http://www.zyxel.kr

Malaysia

• ZyXEL Malaysia Sdn Bhd.

• http://www.zyxel.com.my

Pakistan

• ZyXEL Pakistan (Pvt.) Ltd.

• http://www.zyxel.com.pk

Philippines

• ZyXEL Philippines

• http://www.zyxel.com.ph

Appendix A Customer Support

Europe

Singapore

• ZyXEL Singapore Pte Ltd.

• http://www.zyxel.com.sg

Taiwa n

• ZyXEL Communications Corporation

• http://www.zyxel.com/tw/zh/

Thailand

• ZyXEL Thailand Co., Ltd

• http://www.zyxel.co.th

Vietnam

• ZyXEL Communications Corporation-Vietnam Office

• http://www.zyxel.com/vn/vi

Austria

• ZyXEL Deutschland GmbH

• http://www.zyxel.de

PLA Series User’s Guide

Page 52

Appendix A Customer Support

Belarus

•ZyXEL BY

• http://www.zyxel.by

Belgium

• ZyXEL Communications B.V.

• http://www.zyxel.com/be/nl/

• http://www.zyxel.com/be/fr/

Bulgaria

•ZyXEL България

• http://www.zyxel.com/bg/bg/

Czech Republic

• ZyXEL Communications Czech s.r.o

• http://www.zyxel.cz

Denmark

• ZyXEL Communications A/S

• http://www.zyxel.dk

Estonia

•ZyXEL Estonia

• http://www.zyxel.com/ee/et/

Finland

• ZyXEL Communications

• http://www.zyxel.fi

France

•ZyXEL France

• http://www.zyxel.fr

Germany

• ZyXEL Deutschland GmbH

• http://www.zyxel.de

Hungary

• ZyXEL Hungary & SEE

• http://www.zyxel.hu

PLA Series User’s Guide

Page 53

Appendix A Customer Support

Italy

• ZyXEL Communications Italy

• http://www.zyxel.it/

Latvia

•ZyXEL Latvia

• http://www.zyxel.com/lv/lv/homepage.shtml

Lithuania

• ZyXEL Lithuania

• http://www.zyxel.com/lt/lt/homepage.shtml

Netherlands

•ZyXEL Benelux

• http://www.zyxel.nl

Norway

• ZyXEL Communications

• http://www.zyxel.no

Poland

• ZyXEL Communications Poland

• http://www.zyxel.pl

Romania

•ZyXEL Romania

• http://www.zyxel.com/ro/ro

Russia

• ZyXEL Russia

• http://www.zyxel.ru

Slovakia

• ZyXEL Communications Czech s.r.o. organizacna zlozka

• http://www.zyxel.sk

Spain

• ZyXEL Communications ES Ltd

• http://www.zyxel.es

Sweden

• ZyXEL Communications

PLA Series User’s Guide

Page 54

Appendix A Customer Support

• http://www.zyxel.se

Switzerland

•Studerus AG

• http://www.zyxel.ch/

Turkey

•ZyXEL Turkey A.S.

• http://www.zyxel.com.tr

• ZyXEL Communications UK Ltd.

• http://www.zyxel.co.uk

Ukraine

•ZyXEL Ukraine

• http://www.ua.zyxel.com

Latin America

Argentina

• ZyXEL Communication Corporation

• http://www.zyxel.com/ec/es/

Brazil

• ZyXEL Communications Brasil Ltda.

• https://www.zyxel.com/br/pt/

Ecuador

• ZyXEL Communication Corporation

• http://www.zyxel.com/ec/es/

Middle East

Israel

• ZyXEL Communication Corporation

• http://il.zyxel.com/homepage.shtml

Middle East

• ZyXEL Communication Corporation

PLA Series User’s Guide

Page 55

• http://www.zyxel.com/me/en/

North America

USA

• ZyXEL Communications, Inc. - North America Headquarters

• http://www.zyxel.com/us/en/

Oceania

Australia

• ZyXEL Communications Corporation

• http://www.zyxel.com/au/en/

Africa

Appendix A Customer Support

South Africa

• Nology (Pty) Ltd.

• http://www.zyxel.co.za

PLA Series User’s Guide

Page 56

Appendix A Customer Support

PLA Series User’s Guide

Page 57

any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation.

Disclaimer

ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice.

Regulatory Notice and Statement

UNITED STATES of AMERICA

APPENDIX B

Legal Information

CANADA

The following information applies if you use the product within USA area.

FCC EMC Statement

• The device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.

• This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this device does cause harmful interference to radio or television reception, which is found by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the devices

•Connect the equipment to an outlet other than the receiver’s

•Consult a dealer or an experienced radio/TV technician for assistance

The following information applies if you use the product with RF function within USA area.

FCC Radiation Exposure Statement

• This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

This transmitter must be at least 20 cm from the user and must not be co-located or operating in conjunction with any other antenna or transmitter.

The following information applies if you use the product within Canada area

Industry Canada ICES statement

IC: ICES/NMB - 006

PLA Series User’s Guide

Page 58

Appendix B Legal Information

Industry Canada RSS-GEN & RSS-247 statement

• This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

• This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

If the product with 5G wireless function operating in 5150-5250 MHz and 5725-5850 MHz , the following attention must be paid,

• The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems.

• For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and

• The worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) of RSS 247 shall be clearly indicated.

If the product with 5G wireless function operating in 5250-5350 MHz and 5470-5725 MHz , the following attention must be paid.

• For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 54705725 MHz shall be such that the equipment still complies with the e.i.r.p. limit

• Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

• Le présent émetteur radio de modèle s'il fait partie du matériel de catégorieI) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

Lorsque la fonction sans fil 5G fonctionnant en5150-5250 MHz and 5725-5850 MHz est activée pour ce produit , il est nécessaire de porter une attention particulière aux choses suivantes

• Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;

• Pour les dispositifs munis d’antennes amovibles, le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5 725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à point et l’exploitation non point à point, selon le cas;

• Les pires angles d’inclinaison nécessaires pour rester conforme à l’exigence de la p.i.r.e. applicable au masque d’élévation, et énoncée à la section 6.2.2 3) du CNR-247, doivent être clairement indiqués.

Lorsque la fonction sans fil 5G fonctionnant en 5250-5350 MHz et 5470-5725 MHz est activée pour ce produit , il est nécessaire de porter une attention particulière aux choses suivantes

• Pour les dispositifs munis d’antennes amovibles, le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5 250 à 5 350 MHz et de 5 470 à 5 725 MHz doit être conforme à la limite de la p.i.r.e.

Industry Canada radiation exposure statement

This device complies with IC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Déclaration d’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

EUROPEAN UNION

The following information applies if you use the product within the European Union.

Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive)

Compliance information for 2.4GHz and/or 5GHz wireless products relevant to the EU and other Countries following the EU Directive 1999/ 5/EC (R&TTE)

Български (Bulgarian)

Español (Spanish)

Čeština (Czech)

Dansk (Danish) Undertegnede ZyXEL erklærer herved, at følgende udstyr udstyr overholder de væsentlige krav og øvrige relevante

С настоящото ZyXEL декларира, че това оборудване е в съответствие със съществените изисквания и другите приложими разпоредбите на Директива 1999/5/ЕC.

Por medio de la presente ZyXEL declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

ZyXEL tímto prohlašuje, že tento zařízení je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/EC.

krav i direktiv 1999/5/EF.

PLA Series User’s Guide

Page 59

Appendix B Legal Information

Deutsch (German)

Eesti keel (Estonian)

Ελληνικά (Greek)

English Hereby, ZyXEL declares that this device is in compliance with the essential requirements and other relevant provisions

Français (French)

Hrvatski (Croatian)

Íslenska (Icelandic)

Italiano (Italian)

Latviešu valoda (Latvian)

Lietuvių kalba (Lithuanian)

Magyar (Hungarian)

Malti (Maltese) Hawnhekk, ZyXEL, jiddikjara li dan tagħmir jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li

Nederlands (Dutch)

Polski (Polish) Niniejszym ZyXEL oświadcza, że sprzęt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi

Português (Portuguese)

Română (Romanian)

Slovenčina (Slovak)

Slovenščina (Slovene)

Suomi (Finnish)

Svenska (Swedish)

Norsk (Norwegian)

Hiermit erklärt ZyXEL, dass sich das Gerät Ausstattung in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EU befindet.

Käesolevaga kinnitab ZyXEL seadme seadmed vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ ZyXEL ∆ΗΛΩΝΕΙ ΟΤΙ εξοπλισμός ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕC.

of Directive 1999/5/EC.

Par la présente ZyXEL déclare que l'appareil équipements est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/EC.

ZyXEL ovime izjavljuje da je radijska oprema tipa u skladu s Direktivom 1999/5/EC.

Hér með lýsir, ZyXEL því yfir að þessi búnaður er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipunar 1999/5/EC.

Con la presente ZyXEL dichiara che questo attrezzatura è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Ar šo ZyXEL deklarē, ka iekārtas atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Šiuo ZyXEL deklaruoja, kad šis įranga atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Alulírott, ZyXEL nyilatkozom, hogy a berendezés megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EK irányelv egyéb elõírásainak.

hemm fid-Dirrettiva 1999/5/EC.

Hierbij verklaart ZyXEL dat het toestel uitrusting in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EC.

postanowieniami Dyrektywy 1999/5/EC.

ZyXEL declara que este equipamento está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/EC.

Prin prezenta, ZyXEL declară că acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale Directivei 1999/5/EC.

ZyXEL týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/EC.

ZyXEL izjavlja, da je ta oprema v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/EC.

ZyXEL vakuuttaa täten että laitteet tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Härmed intygar ZyXEL att denna utrustning står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EC.

Erklærer herved ZyXEL at dette utstyret er I samsvar med de grunnleggende kravene og andre relevante bestemmelser I direktiv 1999/5/EF.

This device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.

National Restrictions

This product may be used in all EU countries (and other countries following the EU Directive 1999/5/EC) without any limitation except for the countries mentioned below: Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans aucune

limitation, excepté pour les pays mentionnés ci-dessous: Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttiva 1999/5/EC) senza nessuna limitazione,

eccetto per i paesii menzionati di seguito: Das Produkt kann in allen EU Staaten ohne Einschränkungen eingesetzt werden (sowie in anderen Staaten die der Richtlinie 1999/5/CE

folgen) mit Außnahme der folgenden aufgeführten Staaten: In the majority of the EU and other European countries, the 2.4GHz and 5GHz bands have been made available for the use of wireless

local area networks (LANs). Later in this document you will find an overview of countries in which additional restrictions or requirements or both are applicable.

The requirements for any country may evolve. ZyXEL recommends that you check with the local authorities for the latest status of their national regulations for both the 2.4GHz and 5GHz wireless LANs.

The following countries have restrictions and/or requirements in addition to those given in the table labeled “Ov er v ie w o f Reg ulat ory Requ ir eme nts f or Wir eless LANs”:.

Belgium

PLA Series User’s Guide

Page 60

Appendix B Legal Information

The Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor wireless link having a range exceeding 300 meters. Please check http://www.bipt.be for more details.

Draadloze verbindingen voor buitengebruik en met een reikwijdte van meer dan 300 meter dienen aangemeld te worden bij het Belgisch Instituut voor postdiensten en telecommunicatie (BIPT). Zie http://www.bipt.be voor meer gegevens.

Les liaisons sans fil pour une utilisation en extérieur d’une distance supérieure à 300 mètres doivent être notifiées à l’Institut Belge des services Postaux et des Télécommunications (IBPT). Visitez http://www.ibpt.be pour de plus amples détails.

Denmark In Denmark, the band 5150 - 5350 MHz is also allowed for outdoor usage. I Danmark må frekvensbåndet 5150 - 5350 også anvendes udendørs. Italy This product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy. Unless

this wireless LAN product is operating within the boundaries of the owner's property, its use requires a “general authorization.” Plea s e check http://www.sviluppoeconomico.gov.it/ for more details.

Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all 'interno del proprio fondo, l'utilizzo di prodotti Wireless LAN richiede una “Autorizzazione Generale”. Consultare http://www.sviluppoeconomico.gov.it/ per maggiori dettagli.

Latvia The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic Communications Office. Please check http://

www.esd.lv for more details.

2.4 GHz frekvenèu joslas izmantoðanai ârpus telpâm nepiecieðama atïauja no Elektronisko sakaru direkcijas. Vairâk informâcijas: http://

www.esd.lv. Notes:

1. Although Norway, Switzerland and Liechtenstein are not EU member states, the EU Directive 1999/5/EC has also been implemented in

those countries.

2. The regulatory limits for maximum output power are specified in EIRP. The EIRP level (in dBm) of a device can be calculated by adding

the gain of the antenna used(specified in dBi) to the output power available at the connector (specified in dBm).

List of national codes

COUNTRY ISO 3166 2 LETTER CODE COUNTRY ISO 3166 2 LETTER CODE

Austria AT Liechtenstein LI

Belgium BE Lithuania LT

Bulgaria BG Luxembourg LU

Croatia HR Malta MT

Cyprus CY Netherlands NL

Czech Republic CZ Norway NO

Denmark DK Poland PL

Estonia EE Portugal PT

Finland FI Romania RO

France FR Serbia RS

Germany DE Slovakia SK

Greece GR Slovenia SI

Hungary HU Spain ES

Iceland IS Switzerland CH

Ireland IE Sweden SE

Italy IT Turkey TR

Latvia LV United Kingdom GB

Safety Warnings

• Do not use this product near water, for example, in a wet basement or near a swimming pool.

• Do not expose your device to dampness, dust or corrosive liquids.

• Do not store things on the device.

• Do not install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning.

• Connect ONLY suitable accessories to the device.

• Do not open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information.

• Make sure to connect the cables to the correct ports.

• Place connecting cables carefully so that no one will step on them or stumble over them.

• Always disconnect all cables from this device before servicing or disassembling.

• Do not remove the plug and connect it to a power outlet by itself; always attach the plug to the power adaptor first before connecting it to a power outlet.

PLA Series User’s Guide

Page 61

• Do not allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor or cord.

• Please use the provided or designated connection cables/power cables/ adaptors. Connect it to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe). If the power adaptor or cord is damaged, it might cause electrocution. Remove it from the device and the power source, repairing the power adapter or cord is prohibited. Contact your local vendor to order a new one.

• Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning.

• CAUTION: Risk of explosion if battery is replaced by an incorrect type, dispose of used batteries according to the instruction. Dispose them at the applicable collection point for the recycling of electrical and electronic devices. For detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the store where you purchased the product.

• Do not obstruct the device ventilation slots, as insufficient airflow may harm your device.

The following warning statements apply, where the disconnect device is not incorporated in the device or where the plug on the power supply cord is intended to serve as the disconnect device,

• For permanently connected devices, a readily accessible disconnect device shall be incorporated external to the device;

• For pluggable devices, the socket-outlet shall be installed near the device and shall be easily accessible.

Environment Statement

ErP (Energy-related Products)

ZyXEL products put on the EU market in compliance with the requirement of the European Parliament and the Council published Directive 2009/125/EC establishing a framework for the setting of ecodesign requirements for energy-related products (recast), so called

as "ErP Directive (Energy-related Products directive) as well as ecodesign requirement laid down in applicable implementing measures, power consumption has satisfied regulation requirements which are:

Network standby power consumption < 12W, and/or Off mode power consumption < 0.5W, and/or Standby mode power consumption < 0.5W. Wireless setting, please refer to "Wireless" chapter for more detail.

European Union - Disposal and Recycling Information

The symbol below means that according to local regulations your product and/or its battery shall be disposed of separately from domestic waste. If this product is end of life, take it to a recycling station designated by local authorities. At the time of disposal, the separate collection of your product and/or its battery will help save natural resources and ensure that the environment is sustainable development.

Appendix B Legal Information

Die folgende Symbol bedeutet, dass Ihr Produkt und/oder seine Batterie gemäß den örtlichen Bestimmungen getrennt vom Hausmüll entsorgt werden muss. Wenden Sie sich an eine Recyclingstation, wenn dieses Produkt das Ende seiner Lebensdauer erreicht hat. Zum Zeitpunkt der Entsorgung wird die getrennte Sammlung von Produkt und/oder seiner Batterie dazu beitragen, natürliche Ressourcen zu sparen und die Umwelt und die menschliche Gesundheit zu schützen.

El símbolo de abajo indica que según las regulaciones locales, su producto y/o su batería deberán depositarse como basura separada de la doméstica. Cuando este producto alcance el final de su vida útil, llévelo a un punto limpio. Cuando llegue el momento de desechar el producto, la recogida por separado éste y/o su batería ayudará a salvar los recursos naturales y a proteger la salud humana y medioambiental.

Le symbole ci-dessous signifie que selon les réglementations locales votre produit et/ou sa batterie doivent être éliminés séparément des ordures ménagères. Lorsque ce produit atteint sa fin de vie, amenez-le à un centre de recyclage. Au moment de la mise au rebut, la collecte séparée de votre produit et/ou de sa batterie aidera à économiser les ressources naturelles et protéger l'environnement et la santé humaine.

Il simbolo sotto significa che secondo i regolamenti locali il vostro prodotto e/o batteria deve essere smaltito separatamente dai rifiuti domestici. Quando questo prodotto raggiunge la fine della vita di servizio portarlo a una stazione di riciclaggio. Al momento dello smaltimento, la raccolta separata del vostro prodotto e/o della sua batteria aiuta a risparmiare risorse naturali e a proteggere l'ambiente e la salute umana.

Symbolen innebär att enligt lokal lagstiftning ska produkten och/eller dess batteri kastas separat från hushållsavfallet. När den här produkten når slutet av sin livslängd ska du ta den till en återvinningsstation. Vid tiden för kasseringen bidrar du till en bättre miljö och mänsklig hälsa genom att göra dig av med den på ett återvinningsställe.

PLA Series User’s Guide

Page 62

Appendix B Legal Information

Environmental Product Declaration

PLA Series User’s Guide

Page 63

台灣

Appendix B Legal Information



以下訊息僅適用於產品具有無線功能且銷售至台灣地區第十二條經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

用 20cm 計算 MPE 能符合 1 mW/cm2

電磁波曝露量 MPE 標準值 1mW/cm2，送測產品實測值為： _XX_mW/cm2

無線資訊傳輸設備忍受合法通信之干擾且不得干擾合法通信；如造成干擾，應立即停用，俟無干擾之虞，始得繼續使用。

無線資訊傳設備的製造廠商應確保頻率穩定性，如依製造廠商使用手冊上所述正常操作，發射的信號應維持於操作頻帶中

以下訊息僅適用於產品操作於 5.25-5.35 秭赫頻帶內並銷售至台灣地區

• 在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。

以下訊息僅適用於產品屬於專業安裝並銷售至台灣地區

• 本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者

安全警告

為了您的安全，請先閱讀以下警告及指示 :

• 請勿將此產品接近水、火焰或放置在高溫的環境。

• 避免設備接觸任何液體 - 切勿讓設備接觸水、雨水、高濕度、污水腐蝕性的液體或其他水份。

• 灰塵及污物 - 切勿接觸灰塵、污物、沙土、食物或其他不合適的材料。

• 雷雨天氣時，不要安裝，使用或維修此設備。有遭受電擊的風險。

• 切勿重摔或撞擊設備，並勿使用不正確的電源變壓器。

• 若接上不正確的電源變壓器會有爆炸的風險。

• 請勿隨意更換產品內的電池。

• 如果更換不正確之電池型式，會有爆炸的風險，請依製造商說明書處理使用過之電池。

• 請將廢電池丟棄在適當的電器或電子設備回收處。

• 請勿將設備解體。

• 請勿阻礙設備的散熱孔，空氣對流不足將會造成設備損害。

• 請插在正確的電壓供給插座 ( 如 : 北美 / 台灣電壓 110V AC，歐洲是 230V AC)。

• 假若電源變壓器或電源變壓器的纜線損壞，請從插座拔除，若您還繼續插電使用，會有觸電死亡的風險。

• 請勿試圖修理電源變壓器或電源變壓器的纜線，若有毀損，請直接聯絡您購買的店家，購買一個新的電源變壓器。

• 請勿將此設備安裝於室外，此設備僅適合放置於室內。

• 請勿隨一般垃圾丟棄。

• 請參閱產品背貼上的設備額定功率。

• 請參考產品型錄或是彩盒上的作業溫度。

• 產品沒有斷電裝置或者採用電源線的插頭視為斷電裝置的一部分，以下警語將適用 : －對永久連接之設備，在設備外部須安裝可觸及之斷電裝置；

－對插接式之設備，插座必須接近安裝之地點而且是易於觸及的。

Viewing Certifications

Go to

http://www.zyxel.com to view this product’s documentation and certifications.

ZyXEL Limited Warranty

ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in material or workmanship for a specific period (the Warranty Period) from the date of purchase. The Warranty Period varies by region. Check with your vendor and/or the authorized ZyXEL local distributor for details about the Warranty Period of this product. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product has been modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions.

Note

Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind to the purchaser.

To obtain the services of this warranty, contact your vendor. You may also refer to the warranty policy for the region in which you bought the device at http://www.zyxel.com/web/support_warranty_info.php.

PLA Series User’s Guide

Page 64

Registration

Register your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products.

Open Source Licenses

This product contains in part some free software distributed under GPL license terms and/or GPL like licenses. Open source licenses are provided with the firmware package. You can download the latest firmware at www.zyxel.com. To obtain the source code covered under those Licenses, please contact support@zyxel.com.tw to get it.

Appendix B Legal Information

PLA Series User’s Guide

Page 65

Index

about screen AC Pass-Through 6 Advanced Encryption Standard, see AES 9 AES 10, 28 AES (Advanced Encryption Standard) 9 applications 6

certifications

viewing 63 configuration screen 32 configuration utility 9 connections overview 10 contact information 50 copyright 57 customer support 50

Encrypt Button 6 encryption 9, 28

Guide

Quick Start

HomePlug AV standard

installation

procedure InstallShield wizard 23 introduction 6

19, 25

DAK

10, 28, 33

DAK (Data Access Password) 10 Data Access Key 10 Data Access Password, see DAK 10 disclaimer 57 documentation

related 2

electrical and cable wiring electrical circuit boundaries 28 ENCRYPT Button 16

LED

ETHERNET 8

HomePlug 8

POWER 7, 8 local vs. remote adapter 33

MAC address management

multiple networks

overview 28 managing the device

PLA Series User’s Guide

Page 66

Index

using the utility maximum PHY rate multiple networks 11

network example network information 29 Network Name 10 network name 16

ZyXEL PLA4101, PLA4111, PLA4201, PLA4201 v2, PLA5205 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

PLA Series

Table of Contents

User’s Guide

1.1 Overview

Introducing the PLA

1.2 LEDs

1.3 Standby Mode (Power Saving Mode)

1.4 Ways to Manage the PLA

1.5 Expand Your Network with the PLA

1.6 Security

1.6.1 Passwords

1.6.2 Setting Up Security

1.7 Multiple Networks

The RESET/ENCRYPT Button

2.1 RESET/ENCRYPT Button Overview

2.2 Adding Devices to a Powerline Network

2.3 Removing a Device from a Powerline Network

2.4 Multiple Separate Powerline Networks

2.5 PLAs With One Combination RESET/ENCRYPT Button

2.6 PLAs with Separate RESET and ENCRYPT Buttons

2.6.1 ENCRYPT Button Behavior

2.6.2 RESET Button Behavior

Technical Reference

3.1 Windows

3.1.1 System Requirements

Installing the Utility

3.1.2 Installing the Utility

3.2 Macintosh (Mac)

3.2.1 Supported OSs

3.2.2 Installing the Utility

4.1 Overview

The Configuration Utility

4.1.1 Powerline Network Security

4.1.2 Device Access Key (DAK)

4.2 Starting the Configuration Utility

4.3 Network Info Screen

4.3.1 Icon View

4.3.2 List View

4.4 Configuration Screen

4.5 Advanced Screen

4.6 About Screen

5.1 Overview

Powerline Network Setup Tutorial

5.2 Important Terms

5.3 Accessing Your Powerline Adapter

5.4 Adding a Powerline Adapter

5.5 Setting Up a New Network with a New Adapter

5.6 Splitting a Network into Two Networks

5.7 Troubleshooting

6.1 Power and Light Problems

Troubleshooting

6.2 Configuration Utility Problems

6.3 Powerline Problems

6.4 RESET/ENCRYPT Button Problems

Customer Support

Legal Information

Index