ZyXEL HL-11G User Manual

1

HL-11G

11g mini-PCI Module

User’s Manual

2

FCC S t atement

Warning: Changes or modifications to this unit not expressly approved by the party responsible for

compliance could void the user authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Ope ra tion is su bjec t to the following two
conditions:

(1) this device may not cause harmful inte rferenc e, an d
(2) this device must accept any interference received, inc luding interference tha t may cause undesired

operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio comm unicat ions.

However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

 Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the receiver is

needed.

 Consult the dealer or an experienced radio/TV technic ian for help.

Service Center in U.S.A

Company Name :

ZyXEL Communications, INC. USA

Company Address: 1650 E. Miraloma Ave. Placentia, CA 92870

Tel: [phone]

3

CAUTION:

1. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20
cm must be maintained between the antenna of this device and all persons.

2. This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna and users.
For laptop installations, the antenna must be installed to ensure that the proper spacing is
maintained in the event the users places the device in their lap during use (i.e. posi tioning of
antennas must be placed in the upper portion of the LCD panel only to ensure 20 cm will be
maintained if the user places the device in their lap for use) and

2) The transmitter module may not be co-located with any other transmitter or antenna. As long as
the 2 conditions above are met, further transmitter

testing will not be required. However, the
OEM integrator is still responsible for testing their end-p roduct for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC
peripheral requirements, etc.).

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain

laptop configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-ev aluating the end product (including
the transmitter) and obtaining a separate FCC authorization.

End Product Labeling
This transmitter module is authorized only for use in devices where the antenna may be install ed
such that 20 cm may be maintained between the antenna and users (for example access points,
routers, wireless ASDL modems, certain laptop configurations, and similar equipment). Th e final
end product must be labeled in a visible area with the following: "Contains TX FCC ID:
TWS-HL-11G".

RF Exposure Manual Information That Must be Included
The users manual for end users must include the following information in a prominent location
"IMPORTANT NOTE: To comply with FCC RF exp osure complian ce requirements, the antenna
used for this transmitter must be installed to provide a separation di stance of at least 2 0 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or
transmitter."

Additional Information That Must be Provided to OEM Integrators

The end user should NOT be provided any instructions on how to remove or install the device.