Zhone Technologies 6218-I2-xxx User Manual
✓ Auto-connect feature will
automatically detect the
first usable PVC and
automatically detect
PPPoE, PPPoA, and Bridge
Protocol(with DHCP Server
available)
✓ Configurable as either a
Bridge or Router
ADSL2+ 4Port Modem with WiFi
6218-I2-xxx
ADSL2+ 4 Port WiFi Bridge/Router
✓ 802.11b/g Wireless Access
Point
✓ IGMP v1/v2 support for
video deployments
✓ Filter traffic based on
Destination or Source IP
Address and MAC
Addresses
✓ Traffic Class Rules based
on Protocol, Source IP,
Source Port, Destination
IP, Destination Port,
802.1p
✓ Single Click DSL test - Tests
Ethernet connection and
ADSL Synchronization
along with ATM OAM F5
segment pings and
end-to-end pings.
The 6200 ADSL2+ family of endpoints deliver the required performance for
multimedia applications at very competitive price points. The 6200 ADSL2+
endpoints, in compact form factor, have been successfully used for
residential, business, in-building deployments such as hotel/motel, temporary
housing, and dormitory-campus installations for high-speed internet access
(HSIA) and video-on-demand services.
The Zhone 6200 ADSL2+ endpoints are easily user-installed. The embedded
web-based user interface is designed to simplify ADSL deployment. All
products provide an Ethernet connection that is auto-sensing, eliminating the
worry about connection cable type (straight-through vs crossover).
DELT or Dual End Loop Test, is a feature that is present the 6200 Family of
ADSL2+ CPEs. DELT is primarily used for reactive tests on a loop after a
modem has been deployed—either to help troubleshoot a line or to capture a
baseline of loop characteristics at the time of installation. Because DELT is a
dual-ended test, it requires equipment that supports the DELT feature at both
ends of the copper loop. While this prevents DELT from being used on loops
where no CPE has yet been deployed, DELT in turn offers a deeper set of loop
tests, and can provide very valuable information on the condition of a copper
loop.
Default settings make for a quick and easy installation that doesn't require
any configuration.
The modem, when operating in router mode, support DHCP
Server/Relay/Client, NAPT, as well as RIP, dynamic routing, port forwarding,
and static routing. For security, firewall functions including PAP/CHAP
authentication and IP filtering are supported.
Technical Specifications
Dimensions
■ 1.2" (3.0cm) High x 6.5" (16.5cm) Wide x 4.4"
(11.2cm) Deep
Weight
■ 1.5 lbs (0.7 kg)
Power
■ 100 VAC, 50 Hz
■ 110 VAC, 60 Hz
■ 220 VAC, 50/60 Hz
Interfaces
■ DSL Line: RJ11
■ Ethernet: 4 Port 10/100BaseT
■ Wireless: 802.11b/g
Wireless Support
■ Supports IEEE 802.11b and 802.11g
simultaneously
■ Conforms to Wireless Ethernet Compatibility
Alliance (WECA)
■ Modulation: DFDM with BPSK, QPSK, 16QAM,
64QAM, D8PSK
■ Wireless Media Access Protocol: CSMA/CA with
ACK
■ Supports network authentication: Open, Shared
(WEP 16-bit or 128-bit), 802.1X, WPA,
WPA-PSK, WPA2, WPA2-PSK, Mixed
WPA2/WPA, Mixed WPA2/WPA-PSK
■ Wireless MAC Filter
■ AP Isolation - Wireless clients can not
communicate with each other when enabled
■ Xpress Technology - can improve aggregate
throughput by up to 75% in mixed networks.
ADSL2+ 4Port Modem with WiFi
Standards Support
■ ATM Support
- ITU-T I.610 F4/F5 OAM Send and
Receieve/Loop back
- Support for 8 PVC's
- RFC 1483/2684 (Bridged/Routed Ethernet over
ATM)
■ Routing/Bridge Support
- Transparent Bridge Support
- DHCP Server/Relay/Client
- DNS Relay Agent
- Dynamic DNS Support
- DMZ support
- Static Routing
- RIPv1 and RIPv2
- Policy based QoS (TOS, 802.1p,
Source/Destination IP Address,
Source/Destination Port, Protocol)
- IGMP v1/v2
■ PPP Support: PPPoA, PPPoE, PAP/CHAP
authentication
■ Security
- NAT for Basic Firewall support
- Ingress and Egress Packet Filtering
- Parental Control
- MAC Filtering
- Stateful Packet Inspection
■ DELT support
Protocol Support
■ ANSI T1.413 (Full Rate ADSL)
■ ITU G.992.1 (DMT)
■ ITU G.992.2 (G.lite)
■ ITU G.992.3 (ADSL2)
■ ITU G.992.5 (ADSL2+)
■ ITU G.994.1 (G.hs)
■ ITU G.997.1
■ Annex L
■ Annex M
Management
■ Web-based Configuration GUI
■ CLI
■ Telnet Remote Management
■ FTP/TFTP firmware upgrade and configuration
■ Syslog Support
■ TR-069
Regulatory Compliance
■ FCC Part 15, Part 68
■ CE
■ UL
■ TUV
Operating Requirements
■ Operating Temperature: 32° F to 104° F (0° C to
■ Storage Temperature: –4° F to 149° F (–20° C to
■ Humidity: 5% to 95%, non-condensing
■ Channels 1 ~ 14
■ Total Transmission Power (EIRP) 18dbm
■ Range ~100ft
■ Frequency Range ~ 2.400 - 2.480GHz
backup/restore
40° C)
65° C)
Ordering Information
6218-I2-200 ADSL2+ CPE Router, 802.11G WiFi, N.A.
6218-I2-300 ADSL2+ CPE Router, 802.11G WiFi, U.K.
6218-I2-302 ADSL2+ CPE Router, 802.11G WiFi, EURO
6218-I2-304 ADSL2+ CPE Router, 802.11G WiFi, India
6218-I2-600 ADSL2+ CPE Router, 802.11G WiFi, Japan
2007/05/31 10:16:14
Loading...