Zhone Technologies 6211-l2 User Manual

6211-I2 ADSL2+ Router User’s Guide

May 2006
Document Part Number: 6211-A2-ZB21-60
Zhone Technologies
@Zhone Way
7001 Oakport Street
Oakland, CA 94621
USA
www.zhone.com
info@zhone.com
COPYRIGHT 2000–2006 Zhone Technologies, Inc. All rights reserved.
This publication is protected by copyright law. No part of this publication may be copied, distributed, displayed, modified, transmitted, stored in a retrieval system, or translated without express written permission from Zhone Technologies, Inc.
Acculink, ADSL/R, Bitstorm, Comsphere, DSL the Easy Way, ETC, Etherloop, FrameSaver, GranDSLAM, GrandVIEW, Hotwire, the Hotwire logo, iMarc, Jetstream, MVL, NextEDGE, Net to Net Technologies, OpenLane, Paradyne, the Paradyne logo, Performance Wizard, ReachDSL, StormPort, and TruePut are registered trademarks of Zhone Technologies, Inc.
BAN, Connect to Success, GigMux, Hotwire Connected, JetFusion, JetVision, MALC, MicroBurst, PacketSurfer, Quick Channel, Raptor, Reverse Gateway, SLMS, Spectrum Manager, StormTracker, Z-Edge, Zhone, ZMS, and the Zhone logo are trademarks of Zhone Technologies, Inc.
All other products names or service marks mentioned herein are the trademarks, trade names and service names of their respective owners.
Zhone Technologies makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability, noninfringement, or fitness for a particular purpose. Further, Zhone Technologies reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of Zhone Technologies to notify any person of such revision or changes.
!
Important Safety Instructions
1 Read and follow all warning notices and instructions marked on the
product or included in the manual.
2 Slots and openings in the cabinet are provided for ventilation. To ensure
reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.
3 Do not allow anything to rest on the power cord and do not locate the
product where persons will walk on the power cord.
4 Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous high voltage points or other risks. Refer all servicing to qualified service personnel.
5 General purpose cables are used with this product for connection to the
network. Special cables, which may be required by the regulatory inspection authority for the installation site, are the responsibility of the customer. Use a UL Listed, CSA certified, minimum No. 24 AWG line cord for connection to the Digital Subscriber Line (DSL) network.
6 When installed in the final configuration, the product must comply with
the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance.
7 A rare phenomenon can create a voltage potential between the earth
grounds of two or more buildings. If products installed in separate buildings are interconnected, the voltage potential may cause a hazardous condition. Consult a qualified electrical consultant to determine whether or not this phenomenon exists and, if necessary, implement corrective action prior to interconnecting the products.
8 Input power to this product must be provided by one of the following: (1)
a UL Listed/CSA certified power source with a Class 2 or Limited Power Source (LPS) output for use in North America, or (2) a certified transformer, with a Safety Extra Low Voltage (SELV) output having a maximum of 240 VA available, for use in the country of installation.
9 In addition, since the equipment is to be used with telecommunications
circuits, take the following precautions:
— Never install telephone wiring during a lightning storm.
— Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
— Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
— Use caution when installing or modifying telephone lines.
— Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from lightning.
— Do not use the telephone to report a gas leak in the vicinity of the
leak.
6211-I2 ADSL2+ Router User’s Guide 3
CE Marking
When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be downloaded from the Zhone World Wide Web site at www.zhone.com.
FCC Part 15 Declaration
An FCC Declaration of Conformity may be downloaded from the Zhone World Wide Web site at www.zhone.com.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The authority to operate this equipment is conditioned by the requirement that no modifications will be made to the equipment unless the changes or modifications are expressly approved by the responsible party.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
l Reorient or relocate the receiving antenna.
l Increase the separation between the equipment and receiver.
l Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
l Consult the dealer or an experienced radio/TV technician for help.
Notice to Users of the United States Telephone Network
The following notice applies to versions of the modem that have been FCC Part 68 approved.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachment (ACTA). On the bottom side of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the Telephone Company.
4 6211-I2 ADSL2+ Router User’s Guide
This equipment is intended to connect to the Public Switched Telephone Network through a Universal Service Order Code (USOC) type RJ11C jack. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It has been designed to be connected to a compatible modular jack that is also compliant.
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local Telephone Company. The REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point. For example, 03 represents a REN of 0.3.
If the modem causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens, the Telephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with the modem, refer to the repair and warranty information in this document.
If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is resolved.
The user may make no repairs to the equipment.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
If the site has specially wired alarm equipment connected to the telephone line, ensure the installation of the modem does not disable the alarm equipment. If you have questions about what will disable alarm equipment, consult your Telephone Company or a qualified installer.
6211-I2 ADSL2+ Router User’s Guide 5
Notice to Users of the Canadian Telephone Network
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the equipment. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.
If your equipment is in need of repair, contact your local sales representative, service representative, or distributor directly.
!
CANADA - EMI NOTICE:
This Class B digital apparatus meets all requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial brouilleur du Canada.
Japan Notices
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
6 6211-I2 ADSL2+ Router User’s Guide

CONTENTS

About This Guide 11
Document Purpose and Intended Audience ............................................................11
Document Summary...................................................................................................11
Product-Related Documents......................................................................................12
Contacting Global Service and Support ..................................................................12
Technical Support.......................................................................................................12
Service Requirements.................................................................................................12
Chapter 1 Introduction ............................................................................................................13
Introduction .................................................................................................................13
Features ........................................................................................................................13
System Requirements.................................................................................................13
Parts List ......................................................................................................................14
Front Panel...................................................................................................................15
Rear Panel ....................................................................................................................16
Chapter 2 Hardware Installation and PC Setup ............................................................17
Overview......................................................................................................................17
Connecting the Hardware ..........................................................................................17
Installing the USB Driver..........................................................................................19
Configuring Your Computer .....................................................................................22
Windows XP PCs....................................................................................................22
Windows 2000 PCs.................................................................................................24
Windows ME PCs...................................................................................................24
Windows 95 and Windows 98 PCs.........................................................................25
Windows NT 4.0.....................................................................................................26
Logging in to Your Router ........................................................................................27
Chapter 3 Device Information ...............................................................................................29
Status Summary ..........................................................................................................29
WAN.............................................................................................................................30
LAN Statistics .............................................................................................................31
WAN Statistics............................................................................................................32
6211-I3 ADSL2+ Router User’s Guide 7
ATM Statistics.............................................................................................................33
ADSL Statistics...........................................................................................................34
ADSL BER Test .........................................................................................................34
Route.............................................................................................................................36
ARP...............................................................................................................................37
Chapter 4 Quick Setup ............................................................................................................39
Quick Setup with Auto-Connect Enabled ...............................................................39
Quick Setup with Auto-Connect Disabled ..............................................................41
Chapter 5 Advanced Setup ....................................................................................................43
WAN.............................................................................................................................43
Add Function – ATM PVC Configuration .............................................................44
Connection Type Screen.........................................................................................45
Bridge Service and Quality of Service Screen........................................................46
WAN Setup - Summary..........................................................................................47
Remove Function....................................................................................................48
Finish Function .......................................................................................................48
Local Area Network (LAN) Setup ...........................................................................49
NAT ..............................................................................................................................50
Virtual Servers ........................................................................................................50
Port Triggering ............................................................................................................52
DMZ Host ....................................................................................................................54
Firewall.........................................................................................................................55
IP Filtering – Outgoing...........................................................................................55
IP Filtering – Incoming...........................................................................................57
Firewall – MAC Filtering .......................................................................................59
Parental Control ......................................................................................................62
Quality of Service.......................................................................................................64
Routing – Default Gateway.......................................................................................66
Routing – Static Route ...............................................................................................67
Routing – RIP..............................................................................................................69
DNS Server..................................................................................................................70
Dynamic DNS .............................................................................................................71
ADSL............................................................................................................................73
Modulation Methods...............................................................................................73
Capability................................................................................................................73
DSL Advanced Settings.............................................................................................74
Tone Selection.............................................................................................................75
Port Mapping...............................................................................................................76
Certificate.....................................................................................................................77
Chapter 6 Diagnostics .............................................................................................................81
Testing the DSL Connection.....................................................................................81
8 6211-AZ-ZB21-40
Chapter 7 Management ...........................................................................................................83
Saving and Restoring the Configuration .................................................................83
Backing Up Configuration Settings .........................................................................83
Restoring Configuration Settings .............................................................................85
Restoring Default Settings.........................................................................................87
System Log ..................................................................................................................89
View System Log....................................................................................................90
Configure System Log ............................................................................................91
TR-069 Client..............................................................................................................92
Internet Time ...............................................................................................................93
Access Control – Services .........................................................................................94
Access Control – IP Addresses.................................................................................96
Access Control – Passwords .....................................................................................98
Update Software..........................................................................................................98
Reboot Router .............................................................................................................99
Appendix A Specifications ......................................................................................................101
Index....................................................................................................................................................103
6211-I3 ADSL2+ Router User’s Guide 9
10 6211-AZ-ZB21-40

ABOUT THIS GUIDE

Document Purpose and Intended Audience

This guide contains detailed information about the 6211-I2 router. It is intended for all users of the router.

Document Summary

Section Description
Chapter 1, Introduction Describes the features of the router.
Chapter 2, Hardware
Installation and PC Setup
Chapter 3, Device Information
Chapter 4, Quick Setup Describes the Quick Setup configuration
Chapter 5, Advanced Setup Describes configuration of the advanced router
Chapter 6, Diagnostics Describes the test screen.
Chapter 7, Management Describes the management functions of the
Appendix A,
Specifications
Index Lists key terms, concepts, and sections in
Shows how to connect the router and set up your PC to manage the router.
Explains how to use the web interface to obtain statistics and other information about the router.
process.
features.
router, including backing up and restoring configuration settings, viewing the system log, configuraing access control, and upgrading software.
Lists the specifications of the router.
alphabetical order.
6211-I2 ADSL2+ Router User’s Guide 11

Product-Related Documents

Complete documentation for Zhone products is available online at www.zhone.com.

Contacting Global Service and Support

Contact Global Service and Support (GSS) if you have any questions about this or other Zhone products. Before contacting GSS, make sure you have the following information:
z Zhone product you are using
z System configuration
z Software version running on the system
z Description of the issue

Technical Support

If you require assistance with the installation or operation of your product, or if you want to return a product for repair under warranty, contact GSS. The contact information is as follows:
E-mail
Telephone (North America) 877-ZHONE20
Telephone (International) 510-777-7133
Internet www.zhone.com/support
If you purchased the product from an authorized dealer, distributor, Value Added Reseller (VAR), or third party, contact that supplier for technical assistance and warranty support.

Service Requirements

If the product malfunctions, all repairs must be performed by the manufacturer or a Zhone-authorized agent. It is the responsibility of users requiring service to report the need for service to GSS.
support@zhone.com
12 6211-I2 ADSL2+ Router User’s Guide

INTRODUCTION

1

Introduction

Features

Congratulations on becoming the owner of a 6211 ADSL router.
This User’s Guide will show you how to set up the router, and how to customize its configuration to get the most out of this product.
The 6211 router has the following features:
z Built-in ADSL modem which offers G.Dmt, G.lite, T1.413, ADSL2,
Annex L, and ADSL2+ to meet different linking speeds from your ISP.
z 10/100BaseT Ethernet port to provide Internet connectivity to all
computers on your LAN via additional Ethernet Switch/HUB.
z USB port allows quick installation.
z Built-in splitter provides you to connect telephone directly without using
extra splitter (Model 6211-I1-x0x).
z Configuration program accessible via a web browser, such as Microsoft
Internet Explorer.

System Requirements

In order to use the 6211 ADSL router for Internet access, you must have the following:
z ADSL service subscription from your ISP
z A PC with:
— An Ethernet 10/100BaseT network interface card or USB port
— A processor equivalent to or faster than a Pentium II 133 MHz
— 32 MB RAM or greater
— If USB drivers will be installed, 5 MB free disk space
— Windows 95b, 98, 98SE, 2000, ME, NT, or XP (Note: Windows 95
requires the installation of the Winsock program, not included. Windows 95 and 98 do not support USB.)
6211-I2 ADSL2+ Router User’s Guide 13
Introduction

Parts List

— (Optional) An Ethernet hub or switch, if you wish to connect the
router to several computers on an Ethernet network.
— For system configuration using the supplied web-based program: a
web browser such as Internet Explorer Version 6.0 or later. Netscape is not supported.
In addition to this document, your 6211 ADSL router should come with the following:
z 6211 ADSL router
z Power adapter
z Ethernet cable (RJ45, straight-through type)
z Phone cable (RJ11)
z USB cable
Figure 1: 6211 ADSL Router Package Contents
A
STATUS
POWER
USB
LAN
T C
Y
IT
IV
04-17511
14 6211-I2 ADSL2+ Router User’s Guide

Front Panel

The front panel contains LED indicators that show the status of the unit.
POWER
Figure 2: Front Panel LEDs
LAN
USB
05-17610
ACTIVITY
STATUS
Table 1: Front Panel Label and LEDs
Front Panel
Label Color Function
POWER Green On: Unit is powered on
Off: Unit is powered off
STATUS Green On: ADSL link is established and
active
Flashing: Trying to create an ADSL connection
Off: No ADSL link
ACTIVITY Green Flashing: ADSL data transfer
LAN Green On: LAN link is established
Flashing: Data transfer at LAN connection
Off: No LAN link
USB Green On: USB link is established
Off: No USB link
6211-I2 ADSL2+ Router User’s Guide
15
Introduction

Rear Panel

The rear panel contains the ports for the router's data and power connections.
Table 2: Rear Panel Labels and Connectors
Label Function
LINE Connects to your ADSL line
PHONE (Model 6211-I1-x0x)
USB USB outlet, for PC USB port connection
LAN Connects the CPE to your PC's Ethernet port, or
RESET/DEFAULT To reset the router to its default settings
POWER Connects to the supplied power adapter
Connects to your telephone
to the uplink port on your LAN's hub or switch, using the cable provided
16 6211-I2 ADSL2+ Router User’s Guide

HARDWARE INSTALLATION AND PC SETUP

2

Overview

Connecting the Hardware

This chapter provides basic instructions for connecting the router to a computer or a LAN and to the Internet using DSL. The first part provides instructions to set up the hardware, and the second part describes how to prepare your PC for use with the router.
It is assumed that you have already subscribed to DSL service with your Internet service provider (ISP).
Caution
Shut down your PC and any other equipment before connecting it to the router.
To connect your router:
1 Connect your ADSL line to the port labeled LINE on the rear panel of the
device.
2 For routers with a phone port (model numbers of the form 6211-I1-x0x),
optionally connect your telephone to the port labeled PHONE.
3 Connect your PC or a LAN:
— Use the supplied Ethernet cable to connect your PC directly to the
router. Connect one end of the Ethernet cable to the port labeled LAN on the router and connect the other end to the Ethernet port of your computer.
— Alternatively, use the supplied USB cable to connect your PC directly
to the router. Connect one end of the USB cable to the port labeled USB on the router and connect the other end to a free USB port on your PC. Install the USB drivers as described in the user’s guide on the CD.
— If your LAN has more than one computer, you can attach one end of
an Ethernet cable to a hub or a switch and the other to the LAN port of the router. Either a crossover or straight-through Ethernet cable can be used.
6211-I2 ADSL2+ Router User’s Guide 17
Hardware Installation and PC Setup
4. Connect the AC power adapter to the POWER connector on the back of the device and plug the adapter into a wall outlet or power strip.
RESET
LINE LAN POWERPHONE USB
DEFAULT
1
2
Figure 3: Hardware Installation
3
OR
5. Turn on and boot up your PC and any LAN devices, such as hub or switches, and any computers connected to them.
6. Verify that the router's LEDs are illuminated as shown in Table 3.
4
04-17510
Table 3: LED Indicators (Sheet 1 of 2)
This LED . . . Should be:
POWER Solid green to indicate that the device is turned on. If this
STATUS Solid green to indicate that the router can communicate
ACTIVITY Flashing when the device is sending or receiving data over
18 6211-I2 ADSL2+ Router User’s Guide
light is not on, check if the power adapter is attached to the router and plugged into an AC power source.
with your ISP via ADSL, or flashing when the router is trying to connect to your ISP.
the ADSL connection.
Table 3: LED Indicators (Sheet 2 of 2)
This LED . . . Should be:
LAN Solid green to indicate that the device can communicate
USB Solid green when connected, flashing when the router is
If the LEDs are illuminated as expected, the router is working properly.

Installing the USB Driver

The following section applies only if you use the USB connector on the router. If you connect the USB cable between your PC and the router, Windows detects the new hardware and the Found New Hardware Wizard appears on your PC monitor. Follow this procedure:
Installing the USB Driver
with your PC via Ethernet, or flashing when the router is sending or receiving data over Ethernet.
sending or receiving data.
1 Choose "Install from a list or s
then click on Next.
pecific location" from the Wizard's menu,
Figure 4: Found New Hardware Wizard
6211-I2 ADSL2+ Router User’s Guide
19
Hardware Installation and PC Setup
2 Insert the supplied CD ROM and use Browse to include the CD drive in
the search.
Figure 5: Search and Installation Options
3 If the Wizard reports a compatibility issue, select "Continue Anyway".
Installation of the USB driver proceeds.
Figure 6: Compatibility Warning
20 6211-I2 ADSL2+ Router User’s Guide
Figure 7: Progress Screen
Installing the USB Driver
4. When prompted, click on Finish to close the Wizard.
Figure 8: Completion Screen
6211-I2 ADSL2+ Router User’s Guide
21
Hardware Installation and PC Setup

Configuring Your Computer

Before you can access the router over the LAN or the USB port, you have to configure your PC's TCP/IP address to be 192.168.1.x (where x is any number between 3 and 254), with a subnet mask of 255.255.255.0. Your router's default IP address is 192.168.1.1.

Windows XP PCs

1 In the Windows task bar, click on the Start button, and then click on
Control Panel.
2 Double-click on the Network Connections icon.
3 In the LAN or High-Speed Internet window, right-click on the icon
corresponding to your network interface card (NIC) or USB connection, and select Properties. (Often this icon is labeled Local Area Connection). The Local Area Connection dialog box displays with a list of currently installed network items.
4 Ensure that the check box to the left of the item labeled Internet Protocol
(TCP/IP) is checked, and click on Properties.
Figure 9: Network Connections (Windows XP)
22 6211-I2 ADSL2+ Router User’s Guide
Configuring Your Computer
Figure 10: Local Area Connection Properties (Windows XP)
5 In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio
button labeled Use the following IP address. Type an address between
192.168.1.3 and 192.168.1.254 in the IP Address field (192.168.1.20 is shown here as an example) and 255.255.255.0 in the Subnet Mask field.
Figure 11: TCP/IP Properties (Windows XP)
6211-I2 ADSL2+ Router User’s Guide
23
Hardware Installation and PC Setup

Windows 2000 PCs

6. Click on OK twice to confirm your changes, and close the Control Panel.
1 In the Windows task bar, click on the Start button, point to Settings, and
then click on Control Panel.
2 Double-click on the Network and Dial-up Connections icon.
3 In the Network and Dial-up Connections window, right-click on the Local
Area Connection icon, and then select Properties.
The Local Area Connection Properties dialog box display a list of currently installed network components. If the list includes Internet Protocol (TCP/IP), the protocol has already been enabled; skip to Step 10.
4 If Internet Protocol (TCP/IP) does not appear as an installed component,
click on Install.
5 In the Select Network Component Type dialog box, select Protocol, and
then click on Add.
6 Select Internet Protocol (TCP/IP) in the Network Protocols list, and then
click on OK.

Windows ME PCs

You may be prompted to install files from your Windows 2000 installation CD or other medium. Follow the instructions to install the files.
7 If prompted, click on OK to restart your computer with the new settings.
8 After restarting your PC, double-click on the Network and Dial-up
Connections icon in the Control Panel.
9 In Network and Dial-up Connections window, right-click on the Local
Area Connection icon, and then select Properties.
10 In the Local Area Connection Properties dialog box, select Internet
Protocol (TCP/IP), and then click on Properties.
11 In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio
button labeled Use the following IP address. Type an address between
192.168.1.3 and 192.168.1.254 in the IP Address field and 255.255.255.0 in the Subnet Mask field.
12 Click on OK twice to confirm and save your changes, and then close the
Control Panel.
1 In the Windows task bar, click on the Start button, point to Settings, and
then click on Control Panel.
2 Double-click on the Network and Dial-up Connections icon.
3 In the Network and Dial-up Connections window, right-click on the
24 6211-I2 ADSL2+ Router User’s Guide
Network icon, and then select Properties.
Configuring Your Computer
The Network Properties dialog box displays a list of currently installed network components. If the list includes Internet Protocol (TCP/IP), the protocol has already been enabled; skip to Step 11.
4 If Internet Protocol (TCP/IP) does not appear as an installed component,
click on Add.
5 In the Select Network Component Type dialog box, select Protocol, and
then click on Add.
6 Select Microsoft in the Manufacturers box.
7 Select Internet Protocol (TCP/IP) in the Network Protocols list, and then
click on OK.
You may be prompted to install files from your Windows Me installation CD or other media. Follow the instructions to install the files.
8 If prompted, click on OK to restart your computer with the new settings.
9 After restarting your PC, double-click on the Network and Dial-up
Connections icon in the Control Panel.
10 In Network and Dial-up Connections window, right-click on the Network
icon, and then select Properties.
11 In the Network Properties dialog box, select TCP/IP, and then click on
Properties.
12 In the TCP/IP Settings dialog box, click on the radio button labeled Use
the following IP address. Type an address between 192.168.1.3 and
192.168.1.254 in the IP Address field and 255.255.255.0 in the Subnet Mask field.
13 Click on OK twice to confirm and save your changes, and then close the
Control Panel.

Windows 95 and Windows 98 PCs

1 In the Windows task bar, click on the Start button, point to Settings, and
then click on Control Panel.
2 Double-click on the Network icon.
The Network dialog box displays a list of currently installed network components. If the list includes TCP/IP, the protocol has already been enabled. Skip to step 9.
3 If TCP/IP does not appear as an installed component, click on Add. The
Select Network Component Type dialog box appears.
4 Select Protocol, and then click on Add.
The Select Network Protocol dialog box appears.
5 Click on Microsoft in the Manufacturers list box, and then click on TCP/
IP in the Network Protocols list box.
6 Click on OK to return to the Network dialog box, and then click on OK
again.
6211-I2 ADSL2+ Router User’s Guide
25
Hardware Installation and PC Setup

Windows NT 4.0

You may be prompted to install files from your Windows 95/98 installation CD. Follow the instructions to install the files.
7 Click on OK to restart the PC and complete the TCP/IP installation.
8 After restarting your PC, open the Control Panel window, and then click
on the Network icon.
9 Select the network component labeled TCP/IP, and then click on
Properties.
If you have multiple TCP/IP listings, select the listing associated with your network card or adapter.
10 In the TCP/IP Properties dialog box, click on the IP Address tab.
11 Click in the radio button labeled Use the following IP address. Type an
address between 192.168.1.3 and 192.168.1.254 in the IP Address field and 255.255.255.0 in the Subnet Mask field.
12 Click on OK twice to confirm and save your changes. You will be
prompted to restart Windows. Click on Yes.
1 In the Windows NT task bar, click on the Start button, point to Settings,
and then click on Control Panel.
2 In the Control Panel window, double click on the Network icon.
3 In the Network dialog box, click on the Protocols tab.
The Protocols tab displays a list of currently installed network protocols. If the list includes TCP/IP, the protocol has already been enabled. Skip to
Step 9.
4 If TCP/IP does not appear as an installed component, click on Add.
5 In the Select Network Protocol dialog box, select TCP/IP, and then click
on OK.
You may be prompted to install files from your Windows NT installation CD or other medium. Follow the instructions to install the files.
After all files are installed, a window appears to inform you that a TCP/IP service called DHCP can be set up to dynamically assign IP information.
6 Click on Yes to continue, and then click on OK, if prompted, to restart
your computer.
7 After restarting your PC, open the Control Panel window, and then
double-click on the Network icon.
8 In the Network dialog box, click on the Protocols tab.
9 In the Protocols tab, select TCP/IP, and then click on Properties.
10 In the Microsoft TCP/IP Properties dialog box, click on the radio button
26 6211-I2 ADSL2+ Router User’s Guide
labeled Use the following IP address. Type an address between
192.168.1.3 and 192.168.1.254 in the IP Address field and 255.255.255.0 in the Subnet Mask field.
11 Click on OK twice to confirm and save your changes, and then close the
Control Panel.

Logging in to Your Router

This section shows how to connect to the router's web interface, configure settings, and observe some statistics of your Internet connection.
1 Open your Web browser, and type the following URL in the address/
location box, and press Enter:
http://192.168.1.1
This is the default IP address for the LAN port on the router.
A login screen appears.
Logging in to Your Router
Figure 12: Login Screen
If you have problem connecting to the router, verify that your PC is properly configured within the subnet of the router's default IP address
192.168.1.1. Setup is described in Configuring Your Computer on
page 22.
6211-I2 ADSL2+ Router User’s Guide
27
Hardware Installation and PC Setup
2 Enter your user name and password, and then click on OK to display the
home page of the router's web interface. There are two default user name and password combinations:
Table 4: Default User Names and Passwords
User Name Password Capability
user user Can display device status, but cannot
change or save configuration options.
admin admin Can perform all functions.
You can change the passwords at any time.
The home page is shown in Figure 13.
Figure 13: Web Interface Home Page
28 6211-I2 ADSL2+ Router User’s Guide

DEVICE INFORMATION

3

Status Summary

Display the general status report for the router by clicking on Summary under Device Info (Figure 14).
Figure 14: Status Summary
6211-I2 ADSL2+ Router User’s Guide 29
Device Information
WAN
Display the WAN status report from the by clicking on WAN under Device Info (Figure 15).
Figure 15: WAN Status
30 6211-I2 ADSL2+ Router User’s Guide

LAN Statistics

LAN Statistics
Display LAN statistics by clicking on LAN under Statistics (Figure 16).
Figure 16: LAN Statistics
6211-I2 ADSL2+ Router User’s Guide
31
Device Information

WAN Statistics

Display WAN statistics by clicking on WAN under Statistics (Figure 17).
Figure 17: WAN Statistics
32 6211-I2 ADSL2+ Router User’s Guide

ATM Statistics

ATM Statistics
Display ATM statistics by clicking on ATM under Statistics (Figure 18).
Figure 18: ATM Statistics
6211-I2 ADSL2+ Router User’s Guide
33
Device Information

ADSL Statistics

Display ADSL statistics by clicking on ADSL under Statistics (Figure 19).

ADSL BER Test

Figure 19: ADSL Status
The ADSL Bit Error Rate (BER) test determines the quality of the ADSL connection. The test is performed by transferring idle cells containing a known pattern and comparing the received data with this known pattern to check for any errors (Figure 20 and Figure 21).
To run a BER test:
1 Click on the ADSL BER Test button.
2 Select the test duration and click on Start
3 Check the result.
34 6211-I2 ADSL2+ Router User’s Guide
Figure 20: ADSL BER Test — Start
ADSL BER Test
Figure 21: ADSL BER Test — Result
6211-I2 ADSL2+ Router User’s Guide
35
Device Information

Route

Obtain the Routing status report by clicking on the Route item under Device Info (Figure 22)
Figure 22: Route Information
36 6211-I2 ADSL2+ Router User’s Guide
ARP
ARP
Display the ARP status report by clicking on ARP under Device Info (Figure 23)
Figure 23: ARP Status
6211-I2 ADSL2+ Router User’s Guide
37
Device Information
38 6211-I2 ADSL2+ Router User’s Guide

QUICK SETUP

4

Quick Setup with Auto-Connect Enabled

Auto-connect will automatically detect the first usable PVC and automatically detect PPPoE, PPPoA, and Bridge Protocol (with DHCP Server available). To use auto-connect:
1 Select Quick Setup. The Quick Setup initial screen appears.
Figure 24: Quick Setup Initial Screen
2 Select DSL Auto-Connect, then click on Next. The progress information
screen appears.
6211-I2 ADSL2+ Router User’s Guide 39
Quick Setup
Figure 25: Detecting Available PVC
Figure 26: Detecting available PVC – Available PVC Detected
40 6211-I2 ADSL2+ Router User’s Guide

Quick Setup with Auto-Connect Disabled

Quick Setup with Auto-Connect Disabled
1 Select Quick Setup. The Quick Setup initial screen appears.
Figure 27: Specifying VPI and VCI
2 Verify that DSL Auto-Connect is not selected. Specify VPI and VCI as
directed by your ISP. Click on Next.
3 Use Advanced Setup to configure the PVC.
6211-I2 ADSL2+ Router User’s Guide
41
Quick Setup
42 6211-I2 ADSL2+ Router User’s Guide

ADVANCED SETUP

5
WAN
Set up WAN parameters as directed by your ISP.
Figure 28: WAN Setup Screen
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide 43
Advanced Setup
Add Function – ATM PVC Configuration
If you want to add a new rule for the WAN interface, click on the Add button. The ATM PVC Configuration screen appears. The ATM PVC Configuration screen allows you to configure an ATM PVC identifier (VPI and VCI) and select a service category.
Figure 29: ATM PVC Configuration Screen
Verify the following values with your ISP before you change them.
z VPI (Virtual Path Identifier) – The valid range is 0 to 255.
z VCI (Virtual Channel Identifier) – The valid range is 32 to 65535.
z Service Category – Five classes of traffic defined are defined:
— UBR Without PCR
— UBR With PCR
— CBR
— Non-Realtime VBR
— Realtime VBR
44 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60

Connection Type Screen

Select the type of network protocol and encapsulation mode over the ATM PVC that your ISP has instructed you to use, then click on Next button.
WAN
Figure 30: Connection Type Screen
Select a connection type and click on Next.
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
45
Advanced Setup

Bridge Service and Quality of Service Screen

This WAN service can be enabled or disabled by clicking in the check box.
Enabling QoS for a PVC improves performance for selected classes of applications. However, since QoS also consumes system resources, the number of PVCs is reduced. The default setting for QoS is disabled. If you want to enable QoS service, select the "Enable Quality Of Service" check box.
After finishing steps as above, click on the Next button.
Figure 31: Enable Bridge Service
46 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60

WAN Setup - Summary

Make sure that the settings on the WAN Setup screen match the settings provided by your ISP. If all settings are correct, click on the Save button to save these settings; if not, click on the Back button to make any modifications. If you want to change any item after saving, click on the Edit button to make any modifications.
WAN
Figure 32: WAN Setup Summary
Note
Activate this WAN interface by clicking on the Finish button and further configuring services over this interface. The router supports up to five WAN connections.
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
47
Advanced Setup

Remove Function

If you want to delete a connection from the listed WAN setup, click in the Remove check box next to the item, then click on the Remove button.

Finish Function

Figure 33: WAN Setup List
After you change any item in WAN Setup, remember to click on the Finish button to apply the changes and reboot the system.
48 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60

Local Area Network (LAN) Setup

You can configure the DSL Router IP address and Subnet Mask for the LAN interface to conform your LAN's IP Subnet. The Save button only saves the LAN configuration data. The Save/Reboot button saves the LAN configuration data and reboots the router to make the new configuration effective.
Local Area Network (LAN) Setup
Figure 34: LAN Setup
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
49
Advanced Setup
NAT

Virtual Servers

You can configure the Virtual Server, Port Triggering, and DMZ Host when NAT is enabled.
A virtual server allows you to direct incoming traffic from the WAN side to a specific IP address on the LAN side. Click on the Add button to add a virtual server.
Figure 35: NAT Virtual Server Setup
50 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60
You can select a Service or make new one. Enter the Server IP Address, then click on Save/Apply to submit your configuration.
NAT
Figure 36: Virtual Server Add Screen
On this screen you can view and delete servers. Click in the check box under Remove and click on the Remove button to delete selected virtual servers.
Figure 37: Removing Selected Virtual Servers
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
51
Advanced Setup

Port Triggering

Click the on the Add button to add Port Triggering for your Internet application.
Figure 38: Port Triggering Setup Page
52 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60
You can select an application every time or create new one for your application. Then click on Save/Apply to save your settings.
Port Triggering
Figure 39: Port Triggering Add Page
On this screen you can view and delete applications. Click in the check box under Remove and click on the Remove button to delete selected applications.
Figure 40: Port Triggering List
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
53
Advanced Setup

DMZ Host

You can define the IP address of the DMZ Host on this screen. Enter the IP address and click on Save/Apply.
Figure 41: DMZ Host Setup
54 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60

Firewall

For security reasons, firewall options can be configured only from the LAN side of the router.
IP Filtering – Outgoing
The outgoing filter will block the traffic from the LAN side to the WAN side. Click on Add to create filters.
Firewall
Figure 42: IP Filtering – Outgoing Filter Setup
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
55
Advanced Setup
Input the filter name, source information (from the LAN side), and Destination information (from the WAN side). Then click on Save/Apply.
Figure 43: IP Filtering - Outgoing Filter Add Page
You can view and delete the outgoing filter settings on this screen.
Figure 44: IP Filtering - Outgoing Filter Setup List
56 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60
IP Filtering – Incoming
Incoming filter filters the traffic from the WAN side to the LAN side. Click on Add to add incoming filter settings.
Firewall
Figure 45: IP Filtering – Incoming Filter Setup Page
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
57
Advanced Setup
Enter a filter name, information about the source address (from the WAN side), and information about the destination address ( to the LAN side). Select the protocol and WAN interface. Then click on Save/Apply to add the setting.
Figure 46: IP Filtering - Incoming Filter Add
You can view and delete the incoming filter settings from this screen.
Figure 47: IP Filtering - Incoming Filtering List
58 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60
Firewall – MAC Filtering
MAC filtering can forward or block traffic by MAC address. You can change the policy or add settings to the MAC filtering table using the MAC Filtering Setup screen.
Firewall
Figure 48: IP Filtering - MAC Filtering Setup
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
59
Advanced Setup
If you click on Change Policy, a confirmation dialog lets you verify your change.
Figure 49: IP Filtering - MAC Filtering Policy Change Confirmation
60 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60
If you want to add a setting to the MAC filtering table, enter the Source and Destination MAC address, and select protocol type, frame direction, and WAN interface. Then click on Save/Apply to save it.
Firewall
Figure 50: IP Filtering - MAC Filtering Add Page
On this screen you can view and delete MAC filtering rules.
Figure 51: IP Filtering - MAC Filtering List
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
61
Advanced Setup

Parental Control

Use the Parental Control feature to restrict the days and times a particular device is allowed to access the Internet.
Figure 52: Parental Control Screen
62 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60
To set up parental controls:
1 Click on Add. The Time of Day Restriction screen appears.
Firewall
Figure 53: Parental Control – Time of Day Restrictions
2 Enter a User Name to identify the target of the restrictions.
3 Enter the MAC address of the network adapter to be restricted, and,
optionally, another MAC address.
4 Select the days of the week the restriction is in force.
5 Specify the start and end times the restriction is in force. Use the form
hh:mm, where 23:59, for example, is one minute before midnight.
6 Click on Save/Apply.
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
63
Advanced Setup

Quality of Service

You can configure the Quality of Service to apply different priorities to traffic on the router.
Figure 54: Quality of Service Setup
64 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60
Quality of Service
Click on Add and the Add Network Traffic Class Rule screen appears. Enter and select QoS parameters, then click on Save/Apply. Note that 802.1p Priority and TOS are mutually exclusive.
Figure 55: Quality of Service Add Screen
On this screen you can view and delete QoS settings.
Figure 56: Quality of Service List
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
65
Advanced Setup
Routing – Default Gateway
You can change the Default Gateway on the Routing - Default Gateway screen.
Figure 57: Default Gateway Setup
66 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60
Routing – Static Route
Use the Routing - Static Route screen to add a static route to the routing table.
Routing – Static Route
Figure 58: Static Route Setup
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
67
Advanced Setup
Enter the route information and click on Save/Apply to make it active. No reboot is required.
Figure 59: Static Route Add
68 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60
Routing – RIP
Routing – RIP
If RIP is enabled, the router operation can be configured as Active or Passive.
Figure 60: RIP Setup
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
69
Advanced Setup

DNS Server

Use the DNS Server screen to request automatic assignment of a DNS or to specify a primary and secondary DNS.
Figure 61: DNS Setup
70 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60

Dynamic DNS

Dynamic DNS
Use the Dynamic DNS screen to alias a dynamic IP address to a static hostname, allowing your router to be easily accessed from anywhere on the Internet.
Figure 62: Dynamic DNS
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
71
Advanced Setup
To set up a Dynamic DNS entry:
1 Click on Add. The Add Dynamic DNS screen appears.
Figure 63: Adding a Dynamic DNS Entry
2 Select a D-DNS Provider from the drop-down list.
3 Enter the Hostname you have selected for the interface.
4 Select the router Interface from the drop-down list.
5 Enter the information you used to register with the dynamic DNS service:
for DynDNS, enter your Username and Password; for TOZ, enter your E-mail address and Key.
6 Click on Save/Apply.
72 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60

ADSL

ADSL
There are three major items in the ADSL settings.
Figure 64: ADSL Settings

Modulation Methods

The following modulation methods are supported by the 6211 ADSL router:
z G. d m t E na bl ed
z G.lite Enabled
z T1.413 Enabled
z ADSL2 Enabled
z Annex L Enabled
z ADSL2+ Enabled.
Do not change this setting unless so directed by your ISP.

Capability

The following are included under Capability:
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
73
Advanced Setup
z Bitswap Enable
z SRA (Seamless Rate Adaptation) Enable
Do not change these settings unless so directed by your ISP.

DSL Advanced Settings

Do not change the DSL Advanced Settings unless so directed by your ISP. To view the DSL Advanced Settings screen, click on the Advanced Settings button on the DSL Settings screen (see Figure 64).
There are five test modes between the router and your ISP:
z Normal test: Puts the router in a test mode in which it only sends a
z Reverb test: Puts the router in a test mode in which it only sends a Reverb
z Medley test: Puts the router in a test mode in which it only sends a
Normal signal.
signal.
Medley signal.
z No Retrain: In this mode the router will try to establish a connection as in
normal mode, but once the connection is up it will not retrain if the signal is lost.
z L3: Puts the router into the L3 power state.
Figure 65: DSL Advanced Settings
74 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60

Tone Selection

Tone Selection
To view the ADSL Tone Settings screen, click on the Tone Selection button of the DSL Advanced Settings screen (see Figure 65).
The frequency band of ADSL is split up into 256 separate tones, each spaced
4.3125 kHz apart. With each tone carrying separate data, the technique
operates as if 256 separate modems were running in parallel. The tone range is from 0 to 31 for upstream and from 32 to 255 for downstream.
Do not change these settings unless so directed by your ISP.
Figure 66: Tone Settings
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
75
Advanced Setup

Port Mapping

Use the Port Mapping screen to map multiple ports to a PVC and create bridging groups. Each group will perform as an independent network.
Figure 67: Port Mapping
76 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60
To create a new mapping group:
1 Click on Add. The Port Mapping Configuration screen appears.

Certificate

Certificate
Figure 68: Creating a Port Mapping Entry
2 Enter a unique Group name.
3 Select interfaces from the available interface list and add them to the
grouped interface list using the arrow buttons to create the required mapping of the ports.
4 Click on Save/Apply.
Use the Certificate screen to add, view, or remove a certificate for use by a peer to verify your identity. A maximum of four certificates can be stored. You can add a certificate either by creating a new one or importing an existing one from a location where one is stored.
Note
Certificates are used with TR-069. Firmware that does not support TR-069 will not support certificates.
6211-A2-ZB21-60 6211-I2 ADSL2+ Router User’s Guide
77
Advanced Setup
Figure 69: Certificate
To create a new certificate:
1 Click Create New Certificate Request. Follow the screens that appear to
configure a new certificate.
2 Click on Save/Apply.
78 6211-I2 ADSL2+ Router User’s Guide 6211-A2-ZB21-60

DIAGNOSTICS

6

Testing the DSL Connection

Your router is capable of testing your DSL connection. The individual tests are listed below. If a test displays a failure status, click on "Test" at the bottom of this page to make sure the failure status is consistent. If the test result continues to show a failure, click on "Help" and follow the troubleshooting procedures.
Figure 71: Diagnostics
6211-I2 ADSL2+ Router User’s Guide 81
Diagnostics
82 6211-I2 ADSL2+ Router User’s Guide

MANAGEMENT

7

Saving and Restoring the Configuration

Backing Up Configuration Settings

The configuration of your router can be backed up to a file, and also can be restored from a file. You can also restore the router to its factory default configuration.
To back up your settings, select Management -> Settings -> Backup Settings.
Figure 72: Back Up Settings Screen
6211-I2 ADSL2+ Router User’s Guide 83
Management
Verify that you would like to save the file.
Figure 73: Backup Settings Upload Confirmation
Select the location where you want to save the file.
Figure 74: Backup Settings File Location
84 6211-I2 ADSL2+ Router User’s Guide

Restoring Configuration Settings

To restore saved settings, select Management -> Settings -> Restore User Settings.
Restoring Configuration Settings
Figure 75: Restore User Settings Screen
Select the backup file you want to restore and click on Update Settings.
Figure 76: Restore Settings File Location
6211-I2 ADSL2+ Router User’s Guide
85
Management
The router will restore settings and reboot to activate the restored settings.
Figure 77: Upload in Progress Screen
86 6211-I2 ADSL2+ Router User’s Guide

Restoring Default Settings

Restore Default will erase all current settings and restore the router to factory default settings.
To restore the router to factory default settings, select Management -> Settings -> Restore Default.
Restoring Default Settings
Figure 78: Restore Default Settings Screen
Reply OK to the confirmation dialog.
Figure 79: Restore Default Confirmation Dialog
6211-I2 ADSL2+ Router User’s Guide
87
Management
The router will restore the default settings and reboot.
Figure 80: Restore Default Settings Reboot
88 6211-I2 ADSL2+ Router User’s Guide

System Log

System Log
The System Log dialog allows you to view the System Log and configure the System Log options.
Figure 81: System Log
6211-I2 ADSL2+ Router User’s Guide
89
Management

View System Log

Click on the "View System Log" button to check the log file.
Figure 82: View System Log
90 6211-I2 ADSL2+ Router User’s Guide

Configure System Log

If the log is enabled, the system will log selected events: Emergency, Alert, Critical, Error, Warning, Notice, Informational, and Debugging. All events above or equal to the selected log level will be logged and displayed.
If the selected mode is "Remote" or "Both", events will be sent to the specified IP address and UDP port of a remote system log server. If the selected mode is "Local" or "Both", events will be recorded in the local memory.
System Log
Figure 83: System Log Configuration
Select the desired values and click on the "Save/Apply" button to configure the system log options.
6211-I2 ADSL2+ Router User’s Guide
91
Management

TR-069 Client

The router includes a TR-069 client which is a WAN management protocol. Default values are already filled in. If you wish to enable this protocol, then select Enable and fill in the text boxes according to your configuration. You must click on the Save/Reboot button for the change to take place. Firmware versions that support TR-069 do not support SNMP.
92 6211-I2 ADSL2+ Router User’s Guide

Internet Time

Internet Time
Use the Internet Time screen to specify whether the router uses Simple Network Time Protocol (SNTP) to obtain the time of day from SNTP servers on the Internet.
To set up the router to obtain time from an SNTP server:
1 Select “Automatically synchronize with Internet time servers”. The SNTP
fields appear.
Figure 84: Internet Time Screen
2 Select SNTP servers.
3 Specify the time zone offset for your router’s location.
4 Click on Save/Apply.
6211-I2 ADSL2+ Router User’s Guide
93
Management
Access Control – Services
You can enable or disable some services of your router by LAN or WAN. If no WAN connection is defined, only the LAN side can be configured.
Figure 85: Services Setup
94 6211-I2 ADSL2+ Router User’s Guide
Access Control – Services
If a WAN connection is defined, services of both the LAN side and WAN side can be configured.
Figure 86: Services Setup for LAN and WAN
6211-I2 ADSL2+ Router User’s Guide
95
Management
Access Control – IP Addresses
Web access to the router can be limited when Access Control Mode is enabled. The IP addresses of allowed hosts can be added using Access Control -> IP Address.
Figure 87: IP Address Setup
96 6211-I2 ADSL2+ Router User’s Guide
First, add the IP address to the IP address list.
Access Control – IP Addresses
Figure 88: Access Control – IP Address Add Screen
Then select "Enabled" to enable Access Control Mode.
Figure 89: Access Control – IP Address Enable or Disable
6211-I2 ADSL2+ Router User’s Guide
97
Management
Access Control – Passwords
Use Access Control -> Passwords to change a password. Select an account and enter the current password and the new password. Then click on Save/ Apply.

Update Software

If your ISP releases new software for this router, follow these steps to perform an upgrade.
1. Obtain an updated software image file from your ISP.
2. Enter the path to the image file location or click on the "Browse" button to
locate the image file.
3. Click on the Update Software button once to upload the new image file.
Figure 90: Update Software
98 6211-I2 ADSL2+ Router User’s Guide
Note
The update process takes about two minutes to complete, and your router will reboot automatically.

Reboot Router

Reboot Router
Select Management -> Reboot Router to reboot the router using the web interface. The router will save the current configuration and reboot itself using the new configuration. The rebooting process takes about two minutes to complete.
Figure 91: Reboot Router Screen
Figure 92: Reboot In Progress Screen
6211-I2 ADSL2+ Router User’s Guide
99
Management
100 6211-I2 ADSL2+ Router User’s Guide
SPECIFICATIONS
A
Specifications are subject to change without notice.
Table 5: 6211-I1 Specifications
Specification Criteria
Environment Operating Temperature: 32° F to 104° F (0° C to
40° C) Storage Temperature: –4° F to 149° F (–20° C to 65° C) Humidity: 5% to 95%, non-condensing
Interfaces DSL Line: RJ11
Phone (if present): RJ11 (with integrated phone filter) Ethernet: 10/100BaseT, RJ45 USB 1.1
Power 100 VAC, 50 Hz
110 VAC, 60 Hz 220VAC, 50/60 Hz
Protocol Support ANSI T1.413 (Full Rate ADSL)
ITU G.992.1 (DMT) ITU G.992.2 (G.lite) ITU G.992.3 (ADSL2) ITU G.992.5 (ADSL2+) ITU G.994.1 (G.hs) ITU G.997.1
Size 1.2" High x 6" Wide x 4.4" Deep
(3.0 cm High x 15.2 cm Wide x 11.8 cm Deep)
Weight (Shipping) 1.5 lbs (0.7 kg)
6211-I2 ADSL2+ Router User’s Guide 101
Specifications
102 6211-I2 ADSL2+ Router User’s Guide
Loading...