PRECISION 5.0 VOLT MICROPOWER |
ZRB500 |
|||
VOLTAGE REFERENCE |
|
|
||
ISSUE 1 - OCTOBER 1995 |
|
|
|
|
|
|
|
||
DEVICE DESCRIPTION |
FEATURES |
|||
The ZRB500 uses a bandgap circuit design to |
∙ Small outline SOT23,SO8 and TO92 style |
|||
|
packages |
|||
achieve a precision micropower voltage |
∙ |
|||
reference of 5.0 volts. The device is available in |
No stabilising capacitor required |
|||
small outline surface mount packages, ideal for |
∙ |
|
|
|
applications where space saving is important, |
Typical TC 15ppm/ °C |
|||
as well as packages for through hole |
∙ |
Typical slope resistance 0.33Ω |
||
requirements. |
||||
The ZRB500 design provides a stable voltage |
∙ |
± 3%, 2% and 1% tolerance |
||
without an external capacitor and is stable with |
∙ |
Industrial temperature range |
||
capacitive loads. The ZRB500 is |
∙ |
|
|
|
recommended for operation between 50μA |
|
μ |
||
and 15mA and so is ideally suited to low power |
∙ |
Operating current 50 A to 15mA |
||
Transient response, stable in less than 10μs |
||||
and battery powered applications. |
||||
Excellent performance is maintained to a |
∙ |
APPLICATIONS |
||
suggested absolute maximum of 25mA, |
∙ |
Battery powered and portable equipment. |
||
however the rugged design and 20 volt |
||||
processing allows the reference to withstand |
∙ |
Metering and measurement systems. |
||
transient effects and currents up to 200mA. |
∙ |
|
|
|
Superior switching capability allowsthe device |
Instrumentation. |
|||
to reach stable operating conditions in only a |
∙ |
Test equipment. |
||
few microseconds. |
||||
|
∙ |
Data acquisition systems. |
||
|
∙ |
Precision power supplies. |
SCHEMATIC DIAGRAM
V
R
Gnd
ZRB500
ABSOLUTE MAXIMUM RATING
Reverse Current |
25mA |
Power Dissipation (Tamb=25°C) |
||
SOT23 |
330mW |
|||
Forward Current |
25mA |
|||
E-Line, 3 pin (TO92) |
500mW |
|||
Operating Temperature |
-40 to 85°C |
|||
E-Line, 2 pin (TO92) |
500mW |
|||
Storage Temperature |
-55 to 125°C |
|||
SO8 |
625mW |
|||
|
|
ELECTRICAL CHARACTERISTICS
TEST CONDITIONS (Unless otherwise stated) Tamb=25°C
SYMBOL |
PARAMETER |
CONDITIONS |
|
LIMITS |
|
TOL. |
UNITS |
||
|
|
|
|
|
|
|
|
% |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MIN |
|
TYP |
|
MAX |
|
|
|
|
|
|
|
|
|
|
|
|
VR |
Reverse Breakdown Voltage |
IR=150μA |
4.95 |
|
5.0 |
|
5.05 |
1 |
V |
|
|
|
4.90 |
|
5.0 |
|
5.10 |
2 |
|
|
|
|
4.85 |
|
5.0 |
|
5.15 |
3 |
|
|
|
|
|
|
|
|
|
|
|
IMIN |
Minimum Operating Current |
|
|
|
30 |
|
50 |
|
μA |
|
|
|
|
|
|
|
|
|
|
IR |
Recommended Operating |
|
0.05 |
|
|
|
15 |
|
mA |
|
Current |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TC † |
Average Reverse Breakdown |
|
|
|
15 |
|
50 |
|
ppm/°C |
|
Voltage Temp. Co. |
IR(min) to |
|
|
|
|
|
|
|
|
|
IR(max) |
|
|
|
|
|
|
|
RS § |
Slope Resistance |
|
|
0.33 |
|
1.5 |
|
Ω |
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
ZR |
Reverse Dynamic Impedance |
IR = 1mA |
|
|
0.4 |
|
1 |
|
Ω |
|
|
f = 100Hz |
|
|
|
|
|
|
|
|
|
IAC= 0.1 IR |
|
|
|
|
|
|
|
EN |
Wideband Noise Voltage |
IR = 150μA |
|
|
100 |
|
|
|
|
|
|
f = 10Hz to |
|
|
|
|
|
|
μV(rms) |
|
|
10kHZ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
60 |
|
|
|
† |
TC = |
VR Changex 1000000 |
) |
50 |
|
|
|
|
|
|
|
||||
VR x Temperature Change |
A |
|
|
|
|
||
|
|
μ |
|
|
|
|
|
|
|
|
( |
40 |
|
|
|
|
|
|
t |
|
|
|
|
|
RS = VR Change(IR (min) to IR (max)) |
rren |
|
T)=85°C |
|
|
|
§ |
Cu |
30 |
|
|
|
||
|
|
|
|
|
|
|
|
|
|
IR (max) − IR (min) |
rse |
20 |
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
e |
|
|
|
|
|
|
|
ev |
10 |
|
|
|
|
|
|
R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
T)=-40°C |
|
|
|
|
|
0 |
|
|
|
|
|
|
|
0 |
2.0 |
4.0 |
6.0 |
|
|
|
|
|
Reverse Voltage (V) |
|
|
|
|
|
|
|
Reverse Characteristics |
|