Zebra EM220II EM220II OPOS Driver Setup Utility (en)

EM220II

OPOS Driver Setup Utility

P1007752-025
Rev. 1.00

EM220II

- 2 -

OPOS Driver Setup Utility

Table of Contents

1. Manual Information ........................................................................................................ 6

2. OPOS Driver Setting ...................................................................................................... 6

2-1 POSPrinter Registration ............................................................................................. 7

2-2 MSR Registration ........................................................................................................ 8

Rev. 1.00

EM220II

- 3 -

OPOS Driver Setup Utility

■ Proprietary Statements

This manual contains proprietary information of Zebra Technologies Corporation. It is
intended solely for the information and use of parties operating and maintaining the equip­ment described herein. Such proprietary information may not be used, reproduced, or dis­closed to any other parties for any other purpose without the expressed written permission
of Zebra Technologies Corporation.

Product Improvements
Since continuous product improvement is a policy of Zebra Technologies Corporation, all
specifications and signs are subject to change without notice.

FCC Compliance Statement
NOTE: This equipment has been tested and found to comply with the limits or a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equip­ment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet or circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure re­quirements this device shall be used in accordance with the operating conditions and in­structions listed in this manual.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to insure compliance.
Changes or modifications to this unit not expressly approved by Zebra Technologies Cor­poration could void the user’s authority to operate this equipment.

Rev. 1.00

EM220II

- 4 -

OPOS Driver Setup Utility

Canadian Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
“IC:” before the equipment certification number signifies that the Industry Canada technical
specifications were met. It does not guarantee that the certified product will operate to the
user’s satisfaction.

Liability Disclaimer
Inasmuch as every effort has been made to supply accurate information in this manual,
Zebra Technologies Corporation is not liable for any erroneous information or omissions.
Zebra Technologies Corporation reserves the right to correct any such errors and
disclaims liability resulting therefrom.

No Liability for Consequential Damage
In no event shall Zebra Technologies Corporation or anyone else involved in the creation,
production, or delivery of the accompanying product (including hardware and software) be
liable for any damages whatsoever (including, without limitation, damages for loss of
business profits, business interruption, loss of business information, or other pecuniary
loss) arising out of the use of or the results of use of or inability to use such product, even
if Zebra Technologies Corporation has been advised of the possibility of such damages.
Because some states do not allow the exclusion of liability for consequential or incidental
damages, the above limitation may not apply to you.

Rev. 1.00

EM220II

- 5 -

OPOS Driver Setup Utility

Copyrights

The copyrights in this manual and the label print engine described therein are owned by
Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software
in the label print engine may result in imprisonment of up to one year and fines of up to
$10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.
This product may contain ZPL® , ZPL II® , and ZebraLinktm programs; Element Energy
Equalizer® Circuit; E3® ; and AGFA fonts. Software © ZIH Corp. All rights reserved
worldwide.
ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo,
ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of
ZIH Corp. All rights reserved worldwide.
Monotype® , Intellifont® and UFST® are trademarks of Monotype Imaging, Inc. registered
in the United States Patent and Trademark Office and may be registered in certain jurisdic­tions.
AndyTM , CG PalacioTM, CG Century SchoolbookTM, CG TriumvirateTM, CG TimesTM,
Monotype KaiTM, Monotype MinchoTM and Monotype SungTM are trademarks of
Monotype Imaging, Inc. and may be registered in some jurisdictions.
HY Gothic HangulTM is a trademark of Hanyang Systems, Inc.
AngsanaTM is a trademark of Unity Progress Company (UPC) Limited.
Andale® , Arial® , Book Antiqua® , Corsiva® , Gill Sans® , Sorts® and Times New Roman®
are trademarks of The Monotype Corporation registered in the United States Patent and
Trademark Office and may be registered in certain jurisdictions.

Century Gothic™, Bookman Old StyleTM and Century SchoolbookTM are trademarks of

The Monotype Corporation and may be registered in certain jurisdictions.
HGPGothicB is a trademark of the Ricoh company, Ltd. and may be registered in some ju­risdictions.
UniversTM is a trademark of Heidelberger Druckmaschinen AG, which may be registered
in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly
owned subsidiary of Heidelberger Druckmaschinen AG.
Futura® is a trademark of Bauer Types SA registered in the United States Patent and
Trademark Office and may be registered in some jurisdictions.
TrueType® is a trademark of Apple Computer, Inc. registered in the United States Patent
and Trademark Office and may be registered in certain jurisdictions.
All other product names are the property of their respective owners.
All other brand names, product names, or trademarks belong to their respective holders.
© 2006 ZIH Corp.

Rev. 1.00

EM220II

- 6 -

OPOS Driver Setup Utility

1. Manual Information

This is a manual about how to register and configure EM220II Printer with OPOS Driver.

Throughout this manual, “OLE for Retail POS” is called “OPOS”.
Throughout this manual, “Unified for Retail POS” is called “UPOS”.

2. OPOS Driver Setting

After OPOS Driver installation execute “EM220II OPOS Setup Utility” to register or
configure POSPrinter, “EM220II OPOS Setup Utility” that is located in
“Start>Program>Zebra EM220II OPOS Driver>EM220II OPOS Setup Utility”.

Rev. 1.00

EM220II

- 7 -

OPOS Driver Setup Utility

2-1 POSPrinter Registration

1) Click “Add Printer” button.

2) Set the communication environment of the connected printer and click “OK” button.

3) Click “Checkhealth” to see if the printer operates properly.
<POSPrinter CheckHealth Dialog>

Rev. 1.00

- 8 -

OPOS Driver Setup Utility

2-2 MSR Registration

1) Click “Add MSR” button

2) Select MSR model and Click “NEXT” button.

EM220II

3) Click “Checkhealth” to see if the MSR operates properly

<MSR CheckHealth Dialog >

Rev. 1.00

EM220II

- 9 -

OPOS Driver Setup Utility

Item

Description

Logical Device Name (LDN) [Edit Box]

New Logical Device Names can be modified by typing
the name in the box and then pressing the OK button.

Port [Drop List Combo Box]

Port setting.

Bits per second [Drop List Combo Box]

Baud rate setting for the COM port. This setting will be
restricted according to the limitations of the device. If
using parallel port, this control can not set and reference.

But Length [Drop List Combo Box]

Bit length setting for the COM port. This setting will be
restricted according to the limitations of the device. If
using parallel port, this control can not set and reference.

Parity Bits [Drop List Combo Box]

Parity setting for the COM port. This setting will be
restricted according to the limitations of the device. If
using parallel port, this control can not set and reference.

Stop Bits [Drop List Combo Box]

Stop bit setting for the COM port. This setting will be
restricted according to the limitations of the device. If
using parallel port, this control can not set and reference.

Handshake [Drop List Combo Box]

Handshake setting for the COM port. This setting will be
restricted according to the limitations of the device.
If using parallel port, this control can not set and
reference.

Input Buffer (byte) [Edit Box]

Input buffer size for the COM port. Valid size must be
from 32 to 8192. If using parallel port, this control can not
set and reference.

Output Buffer (byte) [Edit Box]

Output buffer size for the COM and LPT port.
Valid size must be from 32 to 4096.

Output Interval Time (msec) [Edit Box]

Sets the interval between retries (amount of time passed
to the Win 32 API Sleep function) if there has been an
error during output.
Valid time value must be from 0 to 9999. For a slave
device, this is disabled.

Input Sleep Time (msec) [Edit Box]

Sets an interval to be set (amount of time passed to the
Win32 API Sleep function : not assistance) to cause the
Device to sleep during input Valid time value must be
from 0 to 99. For a slave device, this is disabled.

CheckHealth

Invoke the CheckHealth method for this device with
Level = OPOS_CH_INTERACTIVE. This method inform
status of printer.

Apply or OK [Button]

Save current settings and exit.

Cancel[Button]

Discard current settings and exit.

Rev. 1.00

- 10 -

OPOS Driver Setup Utility

* if the system has more ports than the default port range of OPOS

Driver Setup Utility, click “Port Range” button and set the port range.

* If you select the port that the system doesn’t have, the device won’t operate.

EM220II

Rev. 1.00

www.zebra.com

Zebra Technologies International, LLC Zebra Technologies Europe Limited

333 Corporate Woods Parkway Dukes Meadow

Vernon Hills, Illinois 60061, 3109 USA Millboard Road

Phone: [phone]

Toll-Free: +1.800.423.0422

Fax: [phone]

Bourne End

Buckinghamshire, SL8 5XF, UK

Phone: [phone]

Fax: [phone]