Zebra EM220II EM220II Mobile Printer Bluetooth Connection Manual (en)

EM220II

Mobile Printer
Bluetooth Connection Manual

P1007752-031
Rev. 1.00

- 2 -

EM220II

Mobile Printer
Bluetooth Connection Manual

Table of Contents

1. Manual Information ........................................................................................................ 6

2. Precautions .................................................................................................................... 6

3. iOS MFi mode change ................................................................................................... 6

4. Bluetooth Connection Instructions .............................................................................. 7

5. Troubleshooting............................................................................................................. 9

Rev. 1.00

- 3 -

EM220II

Mobile Printer
Bluetooth Connection Manual

■ Proprietary Statements

This manual contains proprietary information of Zebra Technologies Corporation. It is
intended solely for the information and use of parties operating and maintaining the equip­ment described herein. Such proprietary information may not be used, reproduced, or dis­closed to any other parties for any other purpose without the expressed written permission
of Zebra Technologies Corporation.

Product Improvements
Since continuous product improvement is a policy of Zebra Technologies Corporation, all
specifications and signs are subject to change without notice.

FCC Compliance Statement
NOTE: This equipment has been tested and found to comply with the limits or a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equip­ment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet or circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure re­quirements this device shall be used in accordance with the operating conditions and in­structions listed in this manual.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to insure compliance.
Changes or modifications to this unit not expressly approved by Zebra Technologies Cor­poration could void the user’s authority to operate this equipment.

Rev. 1.00

- 4 -

EM220II

Mobile Printer
Bluetooth Connection Manual

Canadian Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
“IC:” before the equipment certification number signifies that the Industry Canada technical
specifications were met. It does not guarantee that the certified product will operate to the
user’s satisfaction.

Liability Disclaimer
Inasmuch as every effort has been made to supply accurate information in this manual,
Zebra Technologies Corporation is not liable for any erroneous information or omissions.
Zebra Technologies Corporation reserves the right to correct any such errors and
disclaims liability resulting therefrom.

No Liability for Consequential Damage
In no event shall Zebra Technologies Corporation or anyone else involved in the creation,
production, or delivery of the accompanying product (including hardware and software) be
liable for any damages whatsoever (including, without limitation, damages for loss of
business profits, business interruption, loss of business information, or other pecuniary
loss) arising out of the use of or the results of use of or inability to use such product, even
if Zebra Technologies Corporation has been advised of the possibility of such damages.
Because some states do not allow the exclusion of liability for consequential or incidental
damages, the above limitation may not apply to you.

Rev. 1.00

- 5 -

EM220II

Mobile Printer
Bluetooth Connection Manual

Copyrights

The copyrights in this manual and the label print engine described therein are owned by
Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software
in the label print engine may result in imprisonment of up to one year and fines of up to
$10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.
This product may contain ZPL® , ZPL II® , and ZebraLinktm programs; Element Energy
Equalizer® Circuit; E3® ; and AGFA fonts. Software © ZIH Corp. All rights reserved
worldwide.
ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo,
ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of
ZIH Corp. All rights reserved worldwide.
Monotype® , Intellifont® and UFST® are trademarks of Monotype Imaging, Inc. registered
in the United States Patent and Trademark Office and may be registered in certain jurisdic­tions.
AndyTM , CG PalacioTM, CG Century SchoolbookTM, CG TriumvirateTM, CG TimesTM,
Monotype KaiTM, Monotype MinchoTM and Monotype SungTM are trademarks of
Monotype Imaging, Inc. and may be registered in some jurisdictions.
HY Gothic HangulTM is a trademark of Hanyang Systems, Inc.
AngsanaTM is a trademark of Unity Progress Company (UPC) Limited.
Andale® , Arial® , Book Antiqua® , Corsiva® , Gill Sans® , Sorts® and Times New Roman®
are trademarks of The Monotype Corporation registered in the United States Patent and
Trademark Office and may be registered in certain jurisdictions.

Century Gothic™, Bookman Old StyleTM and Century SchoolbookTM are trademarks of

The Monotype Corporation and may be registered in certain jurisdictions.
HGPGothicB is a trademark of the Ricoh company, Ltd. and may be registered in some ju­risdictions.
UniversTM is a trademark of Heidelberger Druckmaschinen AG, which may be registered
in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly
owned subsidiary of Heidelberger Druckmaschinen AG.
Futura® is a trademark of Bauer Types SA registered in the United States Patent and
Trademark Office and may be registered in some jurisdictions.
TrueType® is a trademark of Apple Computer, Inc. registered in the United States Patent
and Trademark Office and may be registered in certain jurisdictions.
All other product names are the property of their respective owners.
All other brand names, product names, or trademarks belong to their respective holders.
© 2006 ZIH Corp.

Rev. 1.00

- 6 -

EM220II

Mobile Printer
Bluetooth Connection Manual

1. Manual Information

This Bluetooth Connection Manual provides information on the connection of Bluetooth­enabled iOS devices with the printer (EM220II).

2. Precautions

2-1 To connect the printer with another device via Bluetooth, the devices must be within

10m of one another. The connection is broken if the distance between devices
exceeds 10m.

2-2 The maximum separating distance may be shortened if transmission obstacles, such

as cement walls, are present.

2-3 If a device (such as a microwave oven, wireless LAN, etc.) that uses the same frequen

cy is present, transmission may be interrupted. Separate the printer and Bluetooth­enabled device from such interrupting devices by a distance of at least 5m.

3. iOS MFi mode change

MFi mode is available for Bluetooth communication.
If MFi mode is enable, Bluetooth communication will be only possible with iOS device.

3-1 Set-up by printer button

- Turn on the printer power.

- Push the power button and feed button for 2 seconds while paper cover is opened.

- After beep sound, close the cover.

- Reboot the printer after checking below message.
iOS mode enable!!
Please Reboot Printer!!

- Repeat above procedure to make MFi mode disable.

3-2 iOS mode check

- Implement Self Test

- If firmware version is V01.00 KROBa, iOS mode will be disable.

- If firmware version is V01.00 KROBi, iOS mode will be enable.

Rev. 1.00

- 7 -

EM220II

Mobile Printer
Bluetooth Connection Manual

4. Bluetooth Connection Instructions

This manual focuses on the use of the following devices.

Please use this manual as a guide when using devices other than those listed here.

1) Select the icon. 2) Select “General”.

3) Select “Bluetooth”. 4) Select the printer to connect.

Rev. 1.00

- 8 -

EM220II

Mobile Printer
Bluetooth Connection Manual

5) Enter PIN (default : 0000). 6) Select “Pair”

7) Bluetooth communication is available.

Rev. 1.00

- 9 -

EM220II

Mobile Printer
Bluetooth Connection Manual

5. Troubleshooting

Please follow the guide below if Bluetooth is not searched on iOS device.

1) Perform self test to check the printer is set as iOS mode

2) Check whether printer is connected to other iOS device. Printer is not able to be

found on your iOS device if it is connected to other iOS device. If STATUS LED blinks
when you press Feed button, it means that printer is connected to other iOS device.
You need to disconnect the connection to other iOS device, or turn on the printer
again while the paper cover is opened.

* Printer is automatically connected to last iOS device which was connected in iOS mode.

But it does not make a connection to any device, if user turns it on while the paper
cover of it is opened.

Rev. 1.00

www.zebra.com

Zebra Technologies International, LLC Zebra Technologies Europe Limited

333 Corporate Woods Parkway Dukes Meadow

Vernon Hills, Illinois 60061, 3109 USA Millboard Road

Phone: [phone]

Toll-Free: +1.800.423.0422

Fax: [phone]

Bourne End

Buckinghamshire, SL8 5XF, UK

Phone: [phone]

Fax: [phone]

“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic

accessory has been designed to connect specifically to iPod, iPhone, or iPad,

respectively, and has been certified by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its compliance with safety

and regulatory standards. Please note that the use of this accessory with iPod, iPhone,

or iPad may affect wireless performance.