t
p
f
EM220II Quad Charger Installation Guide
P1007752-034 (Rev.1.0)
◈ Information
This installation guide provides information required for product installation and
use. The EM220II Quad charger offers simultaneous recharging of up to four
EM220II printer batteries.
◈ Components
◈ Battery Charging
EM220II Quad Charger
Installation Guid e
Quad Charger
AC/DC Adaptor
◈ Installation Precautions
1. Avoid placement under direct sunlight and/or locations subject to excessive
heat.
2. Do not use or store in locations subject to high temperatures and/or humidity.
3. Do not use or store in dusty locations.
4. Do not install in unstable and/or non-level locations.
5. Subjecting the product to strong vibration and/or shock can cause damage.
6. Secure sufficient space in the installation area to facilitate easy usage.
◈ Connecting the cables
WARNING
Use only designated AC/DC adaptor. (12VDC, 3A)
NOTE
LED Self-Test
Yellow LED Blinking Error Condition of Quad Charger
CAUTION
1. Initially, Quad Charger performs self test when power is on. When error occurs,
Yellow LED will be blinking.
2. When Yellow LED is blinking continuously, remove the battery and check if
alien substance is on the contact socket on Printer or Quad Charger. Then
disconnect and connect power cord 4 to 5 times to check connection status.
3. Yellow LED is still blinking with above procedures, contact your local dealer.
Power Cord
1. Connect the power cord to the
adaptor, and connect the adaptor to
the power connector of the Quad
Charger.
2. Plug the power cord into a power
Outlet. Input power is 100 ~
240VAC, 50/60Hz, 1.0A.
3. When the power is supplied,
the yellow, gre en and red LED
are on for three seconds and
do the self-t est.
1. Fasten batteries via the battery hooks into the Quad Charger as shown above.
2. Push the battery in until a snapping sound is emitted.
3. Charging begins as soon as the battery is completely inserted. Batteries are
charged to 8.4VDC, 0.8A.
4. Push the hook and pull up to extract the battery.
NOTE
Battery charging status descriptions are as follows.
LED Charging Status Charge Time
Red LED On Charging
Green LED Blinking Over 80% Charged
Green LED On Fully Charged
Red LED Blinking
Error
Replace or Reinstall Ba ttery
2.5 hours
CAUTION
1. If the red LED of the charger blinks, install the battery again.
2. If the red LED continues to blink despite several attempts (4 ~ 5 times) to
install the battery, contact your local dealer.
3. The charging time may vary depending on the type of the charger or ambient
temperature.
◈ WEEE (Waste Electrical and Electric Equipment)
This marking shown on the product or its literature, indicates that it should not be
disposed with other household wastes at the end of its working life. To preven
possible harm to the environment or human health from uncontrolled waste disposal,
lease separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of mate rial resources. Household users should contact either
the retailer where they purchased this product, or their local government office, for
details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supp lier and check the terms and conditions o
the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
☎
Zebra Technologies Corporation
● Web site http://www.zebra.com
● Zebra Technologies Corporation (Global/Americas H eadquarters)
333 Corporate Woods Parkway, Vernon Hills, IL 60061-3109 USA
Tel: +1 847 634 6700 or +1 800 423 0442
● Zebra Technologies Europe Limited
Dukes Meadow, Millboard Road, Bourne End , Buckinghamshire, SL8 5 XF, UK
Tel: +44 (0)1628 556000
● Zebra Technologies Asia Pacific, LLC
120 Robinson Road#06-01 Parakou BuildingSingapore 68913
Tel: +65 6858 0722
● Latin American Sa les Office
9800 NW 41st StreetSuite 220Doral, FL 33178 USA
Tel: +1 305 558 8470
Loading...