Zebra EM220 Microsoft Word - EM 220 Unified Utility Manual_english_Rev_1_00.doc

EM 220
Mobile Printer
Unified Utility Manual
P1007752-018 Rev. 1.00
Table of Contents
1. Notice..............................................................................................................................6
2. Operating System (OS) Environment...........................................................................6
3. Virtual Memory Switch Manager Usage.......................................................................7
3-1 When Using on a PC ..................................................................................................7
3-2 When Using on a PDA..............................................................................................10
4. NV Image Download Manager Usage.........................................................................13
4-1 When Using on a PC ................................................................................................13
4-2 When Using on a PDA..............................................................................................16
5. Firmware Download Manager Usage .........................................................................19
5-1 When Using on a PC ................................................................................................19
5-2 When Using on a PDA..............................................................................................20
5-3 Instructions of Firmware Download...........................................................................21
Rev. 1.00
- 2 -
Mobile Printer Unified Utility Manual
Proprietary Statements
This manual contains proprietary information of Zebra Technologies Corporation. It is intended solely for the information and use of parties operating and maintaining the equip­ment described herein. Such proprietary information may not be used, reproduced, or dis­closed to any other parties for any other purpose without the expressed written permission of Zebra Technologies Corporation.
Product Improvements Since continuous product improvement is a policy of Zebra Technologies Corporation, all specifications and signs are subject to change without notice.
FCC Compliance Statement NOTE: This equipment has been tested and found to comply with the limits or a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip­ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet or circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure re­quirements this device shall be used in accordance with the operating conditions and in­structions listed in this manual. NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to insure compliance. Changes or modifications to this unit not expressly approved by Zebra Technologies Cor­poration could void the user’s authority to operate this equipment.
Rev. 1.00
- 3 -
Mobile Printer Unified Utility Manual
Canadian Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. “IC:” before the equipment certification number signifies that the Industry Canada technical specifications were met. It does not guarantee that the certified product will operate to the user’s satisfaction.
Liability Disclaimer Inasmuch as every effort has been made to supply accurate information in this manual, Zebra Technologies Corporation is not liable for any erroneous information or omissions. Zebra Technologies Corporation reserves the right to correct any such errors and disclaims liability resulting therefrom.
No Liability for Consequential Damage In no event shall Zebra Technologies Corporation or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss) arising out of the use of or the results of use of or inability to use such product, even if Zebra Technologies Corporation has been advised of the possibility of such damages. Because some states do not allow the exclusion of liability for consequential or incidental damages, the above limitation may not apply to you.
Rev. 1.00
- 4 -
Mobile Printer Unified Utility Manual
Copyrights
The copyrights in this manual and the label print engine described therein are owned by Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software in the label print engine may result in imprisonment of up to one year and fines of up to $10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability. This product may contain ZPL®, ZPL II®, and ZebraLinktm programs; Element Energy Equalizer® Circuit; E3®; and AGFA fonts. Software © ZIH Corp. All rights reserved worldwide. ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo, ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of ZIH Corp. All rights reserved worldwide. Monotype®, Intellifont® and UFST® are trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Office and may be registered in certain jurisdic­tions. AndyTM , CG PalacioTM, CG Century SchoolbookTM, CG TriumvirateTM, CG TimesTM, Monotype KaiTM, Monotype MinchoTM and Monotype SungTM are trademarks of Monotype Imaging, Inc. and may be registered in some jurisdictions. HY Gothic HangulTM is a trademark of Hanyang Systems, Inc. AngsanaTM is a trademark of Unity Progress Company (UPC) Limited. Andale®, Arial®, Book Antiqua®, Corsiva®, Gill Sans®, Sorts® and Times New Roman® are trademarks of The Monotype Corporation registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions. Century Gothic™, Bookman Old StyleTM and Century SchoolbookTM are trademarks of The Monotype Corporation and may be registered in certain jurisdictions. HGPGothicB is a trademark of the Ricoh company, Ltd. and may be registered in some ju­risdictions. UniversTM is a trademark of Heidelberger Druckmaschinen AG, which may be registered in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned subsidiary of Heidelberger Druckmaschinen AG. Futura® is a trademark of Bauer Types SA registered in the United States Patent and Trademark Office and may be registered in some jurisdictions. TrueType® is a trademark of Apple Computer, Inc. registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions. All other product names are the property of their respective owners. All other brand names, product names, or trademarks belong to their respective holders. ©2006 ZIH Corp.
Rev. 1.00
- 5 -
Mobile Printer Unified Utility Manual

1. Notice

This Unified Utility Manual provides information on the utility program used to set printer operation conditions and add functions.
The utility program consists of three functions.
1) A function that sets printer operation conditions via non-hardware control, software­based virtual switches (VMSM: Virtual Memory Switch Manager)
2) A function that facilitates the downloading of image files, such as logos, intended for repetitive printing (NV Image Download Manager)
3) A function that is used to download and install the latest Firmware, which is subject to ongoing modification for the enhancement of product performance (Firmware
Download Manager)

2. Operating System (OS) Environment

The following operating systems are supported for usage:
- Microsoft Windows 98
- Microsoft Windows NT 4.0
- Microsoft Windows 2000
- Microsoft Windows XP
- Microsoft Windows 2003
- Microsoft Windows Embedded
- Microsoft Windows Vista
- Microsoft Windows CE 4.2
- Microsoft Windows CE 5.0
- Microsoft Windows CE 6.0
Rev. 1.00
- 6 -
Mobile Printer Unified Utility Manual

3. Virtual Memory Switch Manager Usage

3-1 When Using on a PC

1)
Connect the printer and the PC via the interface cable (USB or Serial type).
If using Bluetooth, a cable connection is not necessary.
2) Turn on the printer power.
3) Prepare the Unified Utility executable file to be used on the PC.
The executable file can be found on the enclosed CD. (EM 220 Unified Utility for PC ver 1.x.x.exe)
4) Run the Unified Utility executable file.
5) Select "Port" and click the "Virtual Memory Switch Manager" button.
Refer to the Bluetooth Connection Manual regarding the Port (may vary according to device).
Rev. 1.00
- 7 -
Mobile Printer Unified Utility Manual
6) The Virtual Memory Switch settings information of the printer appears on screen.
Rev. 1.00
- 8 -
Mobile Printer Unified Utility Manual
7) After setting the desired function(s), click the “Save” button to store settings.
The functions per category are as follows:
Function Description
Printing Density
Sets printing density Value range is 80~15%
Printing Speed
Printer Service
Default Code Page
Default Font Type
Beeps for Low Battery
Beeps for Paper Roll End
Double Byte Character Mode
Auto Power Off Time
Auto Power Saving Time
MSR Trigger
Serial Interface Configuration
Sets printing speed Value range is 50 or 80 mm/s
Printer Service change receipt mode or label mode
Sets the default code page (Refer to the Code Page Manual for more detailed information on the Code Pages supported.)
Sets default font type and size
Sets beeping when reaching low battery capacity
Sets no beeping or beeping when reaching paper roll end
Sets double byte language usage mode
Sets time interval between absence of printer use and automatic turning off of printer power
Sets time interval for automatic entering into power saving mode while the printer is in use
Sets MSR data scanning mode, 7 modes supported (Refer to “GS ( E” in the Control Commands Manual.)
Changes the serial Interface setting *Printer must be reset after change for changed setting to take effect
Sets or cancels Authentication & Encryption mode when connecting
Authentication & Encryption
Connection Mode
PIN Code
Printer Name
Two Dimension Symbol
via Bluetooth * If Authentication & Encryption mode is disabled, connection to a device can be done without a PIN Code Sets Mode1, Mode2, or Mode3 when connecting via Bluetooth
- Mode1: connection possible only with the first device with which connection succeeds
- Mode2: connection with all Bluetooth enabled devices possible via use of a PIN Code
- Mode3: connection possible only with the first device with which connection succeeds and searching or use of connected device possible
Changes the PIN Code required for Bluetooth connections (maximum 12 characters long)
Changes the device name produced when establishing a Bluetooth connection (maximum 12 characters long)
Sets enable 2D barcode or disable Barcode type : PDF417, Data Matrix, Maxi Code, QR Code
* You can check authentication, Encryption mode as well as connection mode of the
Bluetooth from self test page.
8) Reset the printers.
Rev. 1.00
- 9 -
Mobile Printer Unified Utility Manual

3-2 When Using on a PDA

1) Turn on the printer power.
2) Prepare the Unified Utility executable file to be used on the PDA.
The executable file varies according to CPU and can be found on the enclosed CD.
- ARMV4: EM 220 Unified Utility for PPC armv4 ver 1.x.x.exe
- ARMV4I: EM 220 Unified Utility for PPC armv4i ver 1.x.x.exe
3) Run the Unified Utility executable file.
4) Select "Port" and click the "Virtual Memory Switch Manager" button.
Refer to the Bluetooth Connection Manual regarding the Port (may vary according to device).
5) The Virtual Memory Switch settings information of the printer is received and shown on
screen.
Rev. 1.00
- 10 -
Mobile Printer Unified Utility Manual
6) After setting the desired function, click the “Next” button.
(The functions per category are identical to those on the PC.) * Please click "Default" button to return the printer to default setting
7) After setting the desired function, click the “Next” button.
(Clicking the “Prev” button returns to the previous screen.)
Rev. 1.00
- 11 -
Mobile Printer Unified Utility Manual
8) After setting the desired function, click the “Next” button.
9) After setting the desired function, click the “Save” button.
10) Reset the printer.
Rev. 1.00
- 12 -
Mobile Printer Unified Utility Manual

4. NV Image Download Manager Usage

4-1 When Using on a PC

1) The printer connection method and instructions for running the Unified Utility executable file are identical to those provided in “3. Virtual Memory Switch Manager”. Refer to the aforementioned section.
2) Prepare the image file on the PC (e.g. Main.bmp)
3) Select "Port" and click the " NV Image Manager " button.
Refer to the Bluetooth Connection Manual regarding the Port (may vary according to device) “
4) Click the “Add Image” button to add the desired image(s) to the image list. Click the “Remove” button to delete selected image(s), and click the “Reset” button to delete the entire image list.
Rev. 1.00
- 13 -
Mobile Printer Unified Utility Manual
5) The “Used address list” contains the address numbers of saved images.
The following buttons can be used to handle saved images.
- “Print All” Button: Prints all images in the list
- “Print” Button: Prints selected image(s)
- “Reset NV” Button: Delete all images
6) After selecting an image from the image list, adjust the brightness level to set the brightness of the image to be downloaded.
Rev. 1.00
- 14 -
Mobile Printer Unified Utility Manual
7) Click the “Download” button to download the image(s).
Checking the “Auto addressing” box automatically saves address numbers. (Manual input is required if unchecked.)
8) When downloading is complete, the saved address numbers appear in the “NV address
list”.
Rev. 1.00
- 15 -
Mobile Printer Unified Utility Manual

4-2 When Using on a PDA

1) Turn on the printer power.
2) Prepare the Unified Utility executable file to be used on the PDA.
The executable file varies according to CPU and can be found on the enclosed CD.
- ARMV4: EM 220 Unified Utility for PPC armv4 ver 1.x.x.exe
- ARMV4I: EM 220 Unified Utility for PPC armv4i ver 1.x.x.exe
3) Prepare the image file on the PDA (e.g. Main.bmp)
4) Run the Unified Utility executable file.
5) Select "Port" and click the "NV Manager" button.
Refer to the Bluetooth Connection Manual regarding the Port (may vary according to device).
Rev. 1.00
- 16 -
Mobile Printer Unified Utility Manual
6) Click the “Add Image” button to add the desired image(s) to the image list.
Click the “Remove” button to delete selected image(s), and click the “Reset” button to make modifications.
7) The “Used address list” contains the address numbers of saved images.
The following buttons can be used to handle saved images.
- “Print” Button: Prints selected image(s)
- “Print All” Button: Prints all images in the list
- “Reset” Button: Delete all images
Rev. 1.00
- 17 -
Mobile Printer Unified Utility Manual
8) Click the “Download” button to download the image(s).
Automatically saves address numbers. ( Start Address is “00”)
9) When downloading is complete, the saved address numbers appear in the “address”.
Rev. 1.00
- 18 -
Mobile Printer Unified Utility Manual

5. Firmware Download Manager Usage

5-1 When Using on a PC

The printer is already equipped with standard Firmware.
Follow the steps below to download and install firmware on the EM 220 printer.
1) The printer connection method and instructions for running the Unified Utility executable file are identical to those provided in “3. Virtual Memory Switch Manager”. Refer to the aforementioned section.
2) Prepare the Firmware file on the PC.
Firmware can be upgraded to improve printer performance.
3) Select "Port" and click the "Firmware Manager" button.
Refer to the Bluetooth Connection Manual regarding the Port (may vary according to device) “
4) Download firmware; refer to section 5-3 for specifics.
Rev. 1.00
- 19 -
Mobile Printer Unified Utility Manual

5-2 When Using on a PDA

The printer is already equipped with standard Firmware.
Follow the steps below to download and install firmware on the EM 220 printer.
1) Turn on the printer power.
2) Prepare the Unified Utility executable file to be used on the PDA.
The executable file varies according to CPU and can be found on the enclosed CD.
- ARMV4: EM 220 Unified Utility for PPC armv4 ver 1.x.x.exe
- ARMV4I: EM 220 Unified Utility for PPC armv4i ver 1.x.x.exe
3) Prepare the Firmware file on the PDA.
Firmware can be upgraded to improve printer performance.
4) Run the Unified Utility executable file.
5) Select "Port" and click the "Firmware Download Manager" button.
Refer to the Bluetooth Connection Manual regarding the Port (may vary according to device) "
6) Download firmware; refer to section 5-3 for specifics.
Rev. 1.00
- 20 -
Mobile Printer Unified Utility Manual

5-3 Instructions of Firmware Download

1) Open [Unified Utility] and run [Firmware download Manager] to download a firmware (its extension is *.fls)
2) While downloading a firmware, the printer’s status advances as follows:
Green LED lights; Red LED lights; Blue LED lights;
All three LED’s turn on.
3) After step 2 is complete, reset the printer.
4) Open [Unified Utility], run [Firmware download Manager] and download a font file(its extension is *.fls) which matches your downloaded firmware.
The list below provides a mapping of font files to firmware.
- In case of STD: EM_220_f924big.fls, EM_220_f1224big.fls
- In case of KOR: EM_220_f924small.fls, EM_220_f1224small.fls, EM_220_gulim.fls
- In case of CHN, Big 5: EM_220_f1224small.fls, EM_220_f924small.fls, EM_220_big5.fls
- In case of CHN, GB2312:
EM_220_f1224small.fls, EM_220_f924small.fls, EM_220_gb2312.fls
- In case of JPN: EM_220_f1224small.fls, EM_220_f924small.fls, EM_220_japfont.fls
Note: You do not need to reset the printer to use the fonts. You do not need to
download the fonts in any specific order.
5) After downloading the firmware and fonts, you will need to set the memory switches according to user preferences and printer hardware settings.
Rev. 1.00
- 21 -
Mobile Printer Unified Utility Manual
www.zebra.com
______________________________________________________________________
Zebra Technologies International, LLC
333 Corporate Woods Parkway
Vernon Hills, Illinois 60061, 3109 USA
Phone: +1.847.634.6700
Toll-Free: +1.800.423.0422
Fax: +1.847.913.8766
Loading...