EM 220
Mobile Printer
Bluetooth Connection Manual
P1007752-017
Rev. 1.00
EM 220
Table of Contents
1. Manual Information...................................................................................................... 6
2. Precautions .................................................................................................................. 6
3. General Sequence for Bluetooth Connections ......................................................... 6
4. Bluetooth Connection Instructions............................................................................ 7
4-1 Connecting with an Intermec PDA (Device: CN2B, OS: Pocket PC 4.20.0) .......................................... 8
4-2 Connecting with a SYMBOL PDA
4-3 Connecting with an HP PDA
4-4 Connecting with Bluetooth Dongle (BlueSoleil IVT Stack) ...................................................................21
4-5 Connecting with Bluetooth Dongle (Widcomm Stack)..........................................................................25
(Device: SYMBOL MC70, OS: Windows Mobile 5.0)
(Device: iPAQ hx2700, OS: Windows Mobile 5.1.1702)
......................................12
.................................17
Rev. 1.00
- 2 -
Mobile Printer
Bluetooth Connection Manual
EM 220
■ Proprietary Statements
This manual contains proprietary information of Zebra Technologies Corporation. It is
intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission
of Zebra Technologies Corporation.
Product Improvements
Since continuous product improvement is a policy of Zebra Technologies Corporation, all
specifications and signs are subject to change without notice.
FCC Compliance Statement
NOTE: This equipment has been tested and found to comply with the limits or a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet or circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure requirements this device shall be used in accordance with the operating conditions and instructions listed in this manual.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to insure compliance.
Changes or modifications to this unit not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate this equipment.
Rev. 1.00
- 3 -
Mobile Printer
Bluetooth Connection Manual
EM 220
Canadian Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
“IC:” before the equipment certification number signifies that the Industry Canada technical
specifications were met. It does not guarantee that the certified product will operate to the
user’s satisfaction.
Liability Disclaimer
Inasmuch as every effort has been made to supply accurate information in this manual,
Zebra Technologies Corporation is not liable for any erroneous information or omissions.
Zebra Technologies Corporation reserves the right to correct any such errors and
disclaims liability resulting therefrom.
No Liability for Consequential Damage
In no event shall Zebra Technologies Corporation or anyone else involved in the creation,
production, or delivery of the accompanying product (including hardware and software) be
liable for any damages whatsoever (including, without limitation, damages for loss of
business profits, business interruption, loss of business information, or other pecuniary
loss) arising out of the use of or the results of use of or inability to use such product, even
if Zebra Technologies Corporation has been advised of the possibility of such damages.
Because some states do not allow the exclusion of liability for consequential or incidental
damages, the above limitation may not apply to you.
Rev. 1.00
- 4 -
Mobile Printer
Bluetooth Connection Manual
EM 220
Copyrights
The copyrights in this manual and the label print engine described therein are owned by
Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software
in the label print engine may result in imprisonment of up to one year and fines of up to
$10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.
This product may contain ZPL®, ZPL II®, and ZebraLinktm programs; Element Energy
Equalizer® Circuit; E3®; and AGFA fonts. Software © ZIH Corp. All rights reserved
worldwide.
ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo,
ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of
ZIH Corp. All rights reserved worldwide.
Monotype®, Intellifont® and UFST® are trademarks of Monotype Imaging, Inc. registered
in the United States Patent and Trademark Office and may be registered in certain jurisdictions.
AndyTM , CG PalacioTM, CG Century SchoolbookTM, CG TriumvirateTM, CG TimesTM,
Monotype KaiTM, Monotype MinchoTM and Monotype SungTM are trademarks of
Monotype Imaging, Inc. and may be registered in some jurisdictions.
HY Gothic HangulTM is a trademark of Hanyang Systems, Inc.
AngsanaTM is a trademark of Unity Progress Company (UPC) Limited.
Andale®, Arial®, Book Antiqua®, Corsiva®, Gill Sans®, Sorts® and Times New Roman®
are trademarks of The Monotype Corporation registered in the United States Patent and
Trademark Office and may be registered in certain jurisdictions.
Century Gothic™, Bookman Old StyleTM and Century SchoolbookTM are trademarks of
The Monotype Corporation and may be registered in certain jurisdictions.
HGPGothicB is a trademark of the Ricoh company, Ltd. and may be registered in some jurisdictions.
UniversTM is a trademark of Heidelberger Druckmaschinen AG, which may be registered
in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly
owned subsidiary of Heidelberger Druckmaschinen AG.
Futura® is a trademark of Bauer Types SA registered in the United States Patent and
Trademark Office and may be registered in some jurisdictions.
TrueType® is a trademark of Apple Computer, Inc. registered in the United States Patent
and Trademark Office and may be registered in certain jurisdictions.
All other product names are the property of their respective owners.
All other brand names, product names, or trademarks belong to their respective holders.
©2006 ZIH Corp.
Rev. 1.00
- 5 -
Mobile Printer
Bluetooth Connection Manual
EM 220
1. Manual Information
This Bluetooth Connection Manual provides information on the connection of Bluetoothenabled devices (PDAs, PCs, etc.) with the printer (EM 220).
2. Precautions
2-1 To connect the printer with another device via Bluetooth, the devices must be within
10m of one another. The connection is broken if the distance between devices
exceeds 10m.
2-2 The maximum separating distance may be shortened if transmission obstacles, such
as cement walls, are present.
2-3 If a device (such as a microwave oven, wireless LAN, etc.) that uses the same
frequency is present, transmission may be interrupted. Separate the printer and
Bluetooth-enabled device from such interrupting devices by a distance of at least 5m.
3. General Sequence for Bluetooth Connections
Bluetooth connection methods vary by device. The following is the general sequence for
Bluetooth connections, provided for reference purposes.
3-1 Turn on power of each device
- PDAs, PCs (Bluetooth Dongle), printers, etc.
3-2 Run a Bluetooth connection program on the PDA or PC.
3-3 Search for the peripheral with which to establish the connection.
- Search for the printer.
3-4 Register this Printer (EM 220) from the search results.
- If a security setting is enabled, register after entering the PIN Code.
(PIN Code=Pass Key: password of the Bluetooth device, Default code: 0000)
3-5 Test the connection.
- When connected, confirm the designated COM port of fixed COM port and print.
Rev. 1.00
- 6 -
Mobile Printer
Bluetooth Connection Manual
EM 220
4. Bluetooth Connection Instructions
This manual focuses on the use of the following devices:
Please use this manual as a guide when using devices other than those listed below.
- Intermec PDA (Device: CN2B, OS: Pocket PC 4.20.0)
- SYMBOL PDA (Device: SYMBOL MC70, OS: Windows Mobile 5.0)
- HP PDA (Device: iPAQ hx2700, OS: Windows Mobile 5.1.1702)
- Bluetooth Dongle (BlueSoleil IVT Stack, Widcomm Stack)
After turning on the power of all Bluetooth devices, perform the connection process.
- PDAs, PCs (Bluetooth Dongle), printers (EM 220), etc.
Rev. 1.00
- 7 -
Mobile Printer
Bluetooth Connection Manual
4-1 Connecting with an Intermec PDA (Device: CN2B, OS: Pocket PC 4.20.0)
1) Click the icon. 2) Click “Settings”.
EM 220
3) Click “Connections”. 4) Click the “Bluetooth” icon.
Rev. 1.00
- 8 -
Mobile Printer
Bluetooth Connection Manual
5) Click to check the “On” option. 6) Click the “Wireless Printing” menu bar
EM 220
7) Click the ”Device Discovery” button. 8) Select Devices of the EM 220,
and click the “Connect” button.
Rev. 1.00
- 9 -
Mobile Printer
Bluetooth Connection Manual
9) Select the COM port to be used. 10) Check the “Enable Wireless Printing”
and ”Default” checkboxes, and click the
“Printer Test Page” button.
EM 220
11) Click the “OK” button. 12) The PIN Code(Device PIN)
window appears (if the EM 220
security function is enabled).
Rev. 1.00
- 10 -
Mobile Printer
Bluetooth Connection Manual
EM 220
13) Input the PIN Code(Device PIN) 14) If after pressing the “Print Test Page” button,
and click “Next”. (Default code: 0000) the BT LED of the EM 220 turns on and
test printing is performed, the connection is
complete.
Rev. 1.00
- 11 -
Mobile Printer
Bluetooth Connection Manual
4-2 Connecting with a SYMBOL PDA
1) Click the icon. 2) Click “Enable Bluetooth”.
(Device: SYMBOL MC70, OS: Windows Mobile 5.0)
EM 220
3) Click the icon. 4) Click “Show BTExplorer”’.
Rev. 1.00
- 12 -
Mobile Printer
Bluetooth Connection Manual
EM 220
5) Click ”File”. 6) Click “New Connection”.
7) Click “Associate Serial Port”. 8) Click the “Next” button.
Rev. 1.00
- 13 -
Mobile Printer
Bluetooth Connection Manual
EM 220
9) Click the List window for 2 seconds and 10) Click “Refresh”.
the function folder appears.
Click for 2
seconds.
11) Bluetooth devices in the proximity are 12) Select the Device Address of the
discovered. EM 220, and click the “Next” button.
Rev. 1.00
- 14 -
Mobile Printer
Bluetooth Connection Manual
13) The Serial port is registered as COM9. 14) Click the EM 220 name for 2 seconds.
EM 220
15) Click “Connect”. 16) The PIN Code window appears (if the
EM 220 security function is enabled).
Rev. 1.00
- 15 -
Mobile Printer
Bluetooth Connection Manual
EM 220
17) Input the PIN Code and click “OK” . 18) The “Connection Successful” message
(Default PIN Code: 0000) appears, and the connection is complete
when the BT LED of the EM 220 turns on.
Rev. 1.00
- 16 -
Mobile Printer
Bluetooth Connection Manual
4-3 Connecting with an HP PDA
(Device: iPAQ hx2700, OS: Windows Mobile 5.1.1702)
1) To run Bluetooth, first click the 2) Click the Bluetooth logo button
EM 220
icon at the lower right of the screen. to activate the Bluetooth function.
Not active
3) When activated, the Bluetooth button turns 4) Click “New”.
green. Click the “Manager” button to
connect to the EM 220.
Rev. 1.00
- 17 -
Mobile Printer
Bluetooth Connection Manual
EM 220
5) Click “Explore a Bluetooth device”. 6) Click the EM 220 icon from the Bluetooth
devices displayed in the search results.
7) Select Serial Port Profile and click “Next”. 8) Click “Finish”.
Rev. 1.00
- 18 -
Mobile Printer
Bluetooth Connection Manual
EM 220
9) The EM 220 shortcut is produced. 10) Clicking the shortcut for 2 seconds brings
up the function folder. Click “Connect”.
11) The Pass Key window appears (if the 12) Input the Pass Key and click “Enter”
EM 220 security function is enabled). (Default Pass Key: 0000)
Rev. 1.00
- 19 -
Mobile Printer
Bluetooth Connection Manual
13) The shortcut changes to show a green indicator as
Shown below. The connection is complete when the
BT LED of the EM 220 turns on.
EM 220
Rev. 1.00
- 20 -
Mobile Printer
Bluetooth Connection Manual
4-4 Connecting with Bluetooth Dongle (BlueSoleil IVT Stack)
1) After purchasing Bluetooth Dongle, insert the CD in the PC and install Bluesoleil.
2) Connect Bluetooth Dongle to the USB port of the PC.
3) Click the Bluesoleil icon on the PC screen top.
4) Click the red sphere at the center of the Bluesoleil main screen.
EM 220
5) The program initiates a search for Bluetooth devices in the proximity.
Rev. 1.00
- 21 -
Mobile Printer
Bluetooth Connection Manual
EM 220
6) Click right button of the mouse above the “EM 220 Icon” and select the “Pair Device”.
7) Enter the PIN Code in the Bluetooth Passkey window.
(Default Passkey: 0000)
Rev. 1.00
- 22 -
Mobile Printer
Bluetooth Connection Manual
EM 220
8) If the Passkey(PIN Code) is correct and pairing is completed, a red check symbol appears next to
the EM 220 icon.
9) Click right button of the mouse above the “EM 220 Icon” and
select the “Connect > Bluetooth Serial Port Service”.
Rev. 1.00
- 23 -
Mobile Printer
Bluetooth Connection Manual
EM 220
10) When the connection is established, the icon turns green, and a green dotted line appears as
shown in the image below.
11) The connection is complete when the BT LED of the EM 220 turns on.
12) When the connection is complete, the message pictured below appears at the bottom right of the
PC screen.
The COM port number shown in the message indicates the COM port via which the EM 220 and
the PC are connected.
Rev. 1.00
- 24 -
Mobile Printer
Bluetooth Connection Manual
4-5 Connecting with Bluetooth Dongle (Widcomm Stack)
1) After purchasing Bluetooth Dongle, insert the CD in the PC and install Bluesoleil.
2) Connect Bluetooth Dongle to the USB port of the PC.
3) Click the My Bluetooth Places icon on the PC screen top.
4) Click “Bluetooth Tasks > Add a Bluetooth services”
EM 220
5) Click “Next”.
Rev. 1.00
- 25 -
Mobile Printer
Bluetooth Connection Manual
EM 220
6) Select “Show all devices” and Click “Next”.
7) The program initiates a search for Bluetooth devices in the proximity. Click “Next”.
Rev. 1.00
- 26 -
Mobile Printer
Bluetooth Connection Manual
EM 220
8) Enter the PIN Code in the Bluetooth Passkey window.
(Default Passkey: 0000)
9) If the Passkey(PIN Code) is correct and pairing is completed, a green check symbol appears next
to the Serial Port Profile icon. Click “Configure”
Rev. 1.00
- 27 -
Mobile Printer
Bluetooth Connection Manual
EM 220
10) Check COM Port
11) Click “Next”
Rev. 1.00
- 28 -
Mobile Printer
Bluetooth Connection Manual
EM 220
12) Click “Finish”.
13) The shortcut changes to show a green indicator as shown below. The connection is
Complete when the BT LED of the EM 220 turns on.
Rev. 1.00
- 29 -
Mobile Printer
Bluetooth Connection Manual
www.zebra.com
______________________________________________________________________
Zebra Technologies International, LLC
333 Corporate Woods Parkway
Vernon Hills, Illinois 60061, 3109 USA
Phone: +1.847.634.6700
Toll-Free: +1.800.423.0422
Fax: +1.847.913.8766
Loading...