Zanussi ZWF 0143BWH User Manual
GETTING
STARTED?
EASY.
User Manual
ZWF 0143BWH
EN User Manual 2
Washing Machine
DE Benutzerinformation 19
Waschmaschine
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
• This appliance can be used by children aged 8 years and
above and by persons with reduced capabilities provided that
they have been given instruction and/or supervision regarding
the safe use of the appliance and understand the potential
hazards involved.
• Do not let children play with the appliance.
• Children under 3 years of age should be kept away from the
appliance unless continuously supervised.
• Keep all packaging away from children and dispose of it
appropriately.
• Keep detergents away from children.
• Keep children and pets away from the appliance door when it is
open.
• Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
• Do not change the specification of this appliance.
• Do not exceed the maximum load of 10 kg (refer to the
"Programme chart" chapter).
• The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
• The ventilation opening in the base (if applicable) must not be
covered by a carpet, mat, or any floor covering.
• The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
2
• Old hose sets must not be reused.
• If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
• Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
• Do not use high pressure water sprays and/or steam to clean
the appliance.
• Clean the appliance with a moist cloth. Use only neutral,
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
• Remove all the packaging and the transit bolts.
• Keep the transit bolts in a safe place. If the
appliance is to be moved in future they must be
reattached to lock the drum to prevent internal
damage.
• Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
• Do not install or use a damaged appliance.
• Follow the installation instruction supplied with
the appliance.
• Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
• The floor area where the appliance is to be
installed must be flat, stable, heat resistant and
clean.
• Make sure that there is air circulation between
the appliance and the floor.
• Adjust the feet to have the necessary space
between the appliance and the flooring.
• Do not install the appliance where the appliance
door cannot be fully opened.
ELECTRICAL CONNECTION
• The appliance must be earthed.
• Always use a correctly installed shockproof
socket.
• Make sure that the electrical information on the
rating plate agrees with the power supply. If not,
contact an electrician.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
• Do not touch the mains cable or the mains plug
with wet hands.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
• This appliance complies with the E.E.C.
Directives.
WATER CONNECTION
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
USE
WARNING! Risk of injury, electrical
shock, fire, burns or damage to the
appliance.
• This appliance is for household use only.
• Follow the safety instructions on the detergent
packaging.
• Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
• Make sure that all metal objects are removed
from the laundry.
3
• Do not put a container to collect possible water
leakage under the appliance. Contact the
Authorised Service Centre to ensure which
accessories can be used.
• Do not touch the glass door while a programme
is in operation. The glass can get hot.
SERVICE
• To repair the appliance contact an Authorised
Service Centre.
• Use original spare parts only.
DISPOSAL
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains
electrical and water supplies.
• Cut off the mains electrical cable close to the
appliance and dispose of it.
• Remove the door catch to prevent children or
pets from becoming trapped in the drum.
• Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1 2 3
5
6
4
1
Worktop
2
Detergent dispenser
3
Control panel
4
Door handle
5
Rating plate
6
Feet for levelling the appliance
4
CONTROL PANEL
CONTROL PANEL DESCRIPTION
97621 3 4 5 8
1
On / Off button (Aan/Uit Marche/Arrêt)
2
Programme selection touchpad
3
Temperature touchpad
4
Spin selection touchpad
5
Options selection touchpad
6
Start/Pause touchpad
7
Finish in touchpad (Klaar Over/Fini Dans)
8
Display
9
Door locked indicator
DISPLAY
A
DB
C
A. The time area:
• : the programme duration
• : the "finish in" time
• : the alarm codes
• : the message of error
• : the programme is completed.
B. The child lock indicator:
• The indicator comes on when you activate
this device.
C. The extra rinse indicator:
• The indicator comes on when you activate
this option.
D. The Klaar Over/Fini Dans touchpad.
5
PROGRAMME CHART
Programme
Temperature range
Maximum load
Maximum spin
speed
Programme description
(Type of load and soil level)
30'@30°
30°C
3 kg
800 rpm
A short cycle for synthetic and delicate items with
light soil level or for items to freshen up.
Katoen/Coton
90°C - Cold
10 kg
1400 rpm
White cotton and coloured cotton. Normal soil and
light soil.
Katoen/
Coton ECO
1)
60°C - 40°C
10 kg
1400 rpm
White cotton and fast-coloured cotton. Normal soil.
The energy consumption decreases and the time of the
washing programme is extended.
Synthetica/
Synthétiques
60°C - Cold
4 kg
1200 rpm
Synthetic items or mixed fabric items. Normal soil.
Fijne Was/Délicats
40°C - Cold
4 kg
1200 rpm
Delicate fabrics such as acrylics, viscose, polyester
items. Normal soil.
Wol/Laine
40°C - Cold
1,5 kg
1200 rpm
Machine washable wool, hand washable wool and
delicate fabrics with «hand washing» care symbol.
2)
Dekbed/Couette
60°C - Cold
3 kg
800 rpm
Special programme for one synthetic blanket, duvet,
bedspread and so on.
Mix 20°/Mixtes
20°
20°C
2 kg
1200 rpm
Special programme for cotton, synthetic and mixed fabrics
with light soil. Set this programme to decrease the energy
consumption. Make sure that the detergent is for low tem-
perature in order to have good washing results3).
1) Standard programmes for the Energy Label consumption values. According to regulation
1061/2010, these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton programme». They are the most efficient programmes in terms of combined energy and
water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the
selected programme.
2) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
3) No temperature indicator is on .
6
Programme options compatibility
Programme
Snel/Rapide
1)
Intensief/Intensif
Anti-kreuk/Anti-froissage
Spoelen/Rinçage
Pompen/Centrifugeren Vidange/Essorage
30'@30° ■ ■ ■ ■
Katoen/
Coton
■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Katoen/
Coton ECO
■ ■ ■ ■ ■ ■ ■ ■
Synthetica/
Synthétiques
■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Fijne Was/
Délicats
■ ■ ■ ■ ■ ■ ■ ■ ■
Wol/Laine ■ ■ ■ ■ ■ ■
Dekbed/
Couette
■ ■ ■ ■ ■ ■
Mix 20°/
Mixtes 20°
■ ■ ■ ■ ■ ■ ■
1) When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to
keep the full load but the washing results can be unsatisfactory. Recommended load: cotton: 5 kg, synthetics and delicates: 2,5 kg.
CONSUMPTION VALUES
The data in this table are approximate. Different variables can affect the data: the quantity
and type of laundry, the water and ambient temperature.
7
At the start of the programme, the display shows the programme duration for the maximum load capacity.
During the washing phase the programme duration is automatically calculated and can be
greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton
60°C, maximum load capacity 10 kg, the programme duration exceeds 2 hours; actual
load 1 kg, the programme duration will be less than 1 hour).
When the appliance is calculating the real programme duration a dot flashes in the display.
Programmes Load (kg)
Energy con-
sumption
(kWh)
Water con-
sumption (li-
tre)
Approximate
programme
duration (mi-
nutes)
Remaining
moisture (%)
1)
Katoen/Coton 60°C 10 2,04 87 240 52
Katoen/Coton 40°C 10 1,40 83 210 52
Synthetica/Synthé-
tiques 40°C
4 0,80 61 140 35
Fijne Was/Délicats
40°C
4 0,56 75 95 35
Wol/Laine 30°C
2)
1,5 0,42 62 75 30
Standard cotton programmes
Standard 60°C cot-
ton
10 1,02 57 252 52
Standard 60°C cotton
5 0,75 46 205 52
Standard 40°C cotton
5 0,67 46 205 52
1) At the end of spin phase.
2) Not available for some models.
Off Mode (W) Left On Mode (W)
0.48 0.48
The information given in the chart above is compliant with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC.
8
OPTIONS
TEMPERATURE
With this option you can change the default
temperature.
Indicator = cold water.
The indicator of the set temperature comes on.
SPIN
With this option you can change the default spin
speed.
The indicator of the set speed comes on.
Additional spin options:
No Spin
• Set this option to deactivate all spin phases.
Only the drain phase is available.
• The related indicator comes on.
• Set this option for very delicate fabrics.
• The rinses phase uses more water for some
washing programmes.
Rinse Hold
• Set this option to prevent the laundry creases.
• The related indicator comes on.
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the laundry
creases.
• The door stays locked. You must drain the water
to unlock the door.
To drain the water refer to ‘At the end
of the programme’.
SNEL/RAPIDE
With this option you can decrease the programme
duration.
Use this option for items with light soil or items to
refresh.
The related indicator comes on.
INTENSIEF/INTENSIF
With this option you can wash very soiled laundry.
The washing cycle lasts longer with this option.
The related indicator comes on.
ANTI-KREUK/ANTI-FROISSAGE
The appliance carefully washes and spins the
laundry to prevent the creases.
The appliance decreases the spin speed, uses
more water and adapts the programme duration to
the type of laundry.
The related indicator comes on.
SPOELEN/RINÇAGE
With this option you can perform only a last rinse of
a selected washing programme.
If you set also the Extra Rinse function ( ) the
appliance adds two or more rinses.
The related indicator comes on.
POMPEN/CENTRIFUGEREN VIDANGE/
ESSORAGE
With this option you can perform the spin and drain
cycle.
The spin phase is suitable to the washing
programme you set.
If you set also the No Spin ( )
option, the appliance only drains.
KLAAR OVER/FINI DANS
With this option you can set the number of hours in
which you would like your washing programme to
be completed.
You can set from minimum 3 hours to maximum 20
hours.
The display shows the number of hours and the
indicator above the button
is on.
EXTRA RINSE
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to detergents
and in areas where the water is soft.
The related indicator comes on.
1)
1) See in "Settings" how to activate this option.
9
SETTINGS
PERMANENT EXTRA RINSE
With this option you can permanently have an extra
rinse when you set a new programme.
• To activate/deactivate this option touch the
buttons and at the same time until the
indicator comes on/goes off.
CHILD LOCK
With this option you can prevent that the children
play with the control panel.
• To activate/deactivate this option, touch the
buttons and at the same time until the
indicator comes on/goes off.
Activate this option after you touch the button :
the buttons are locked (except for the button ) .
This option stays active even when you
switch off the appliance.
ACOUSTIC SIGNALS
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals,
touch the buttons
and at the same time for 4
seconds.
If you deactivate the acoustic signals,
they continue operate when the
appliance has a malfunction.
BEFORE FIRST USE
1. Put a small quantity of detergent in the
compartment for washing phase.
2. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and the
tub.
DAILY USE
WARNING! Refer to Safety chapters.
LOADING THE LAUNDRY
Open the water tap. Connect the mains plug to the
mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the drum.
Refer to max. loads indicated in "Programme chart".
4. Close the door.
CAUTION!
Make sure
that no laundry stays between the
seal and the
door. There
is a risk of
water leakage or damage to the
laundry.
10
USING DETERGENT AND ADDITIVES
1. Measure out the detergent and the fabric
conditioner.
2. Put the detergent
and the fabric conditioner into the compartments.
3. Carefully close the
detergent drawer.
DETERGENT COMPARTMENTS
Detergent compartment for
washing phase.
If you use liquid detergent, put it
immediately before you start the
programme.
Compartment for liquid additives
(fabric conditioner, starch).
CAUTION! Do not
exceed the MAX
level.
Flap for powder or liquid detergent.
LIQUID OR POWDER DETERGENT
A
The default position of
the flap is A (powder detergent).
To use liquid detergent:
1. Remove the drawer.
Push the drawer edge in
the place with the arrow
(PUSH) to remove the
drawer easily.
B
2. Adjust the flap in position B.
3. Put back the drawer in
the recess.
When you use the liquid detergent:
• Do not use gelatinous or thick liquid detergents.
• Do not put more liquid then 120
ml.
• Do not set the delay start.
A
When the flap is in position B and you want to
use powder detergent:
1. Remove the drawer.
2. Adjust the flap in position A.
3. Put back the drawer
in the recess.
• Measure out the detergent and the fabric conditioner.
• Put the detergent and the fabric conditioner into
the compartments.
• Carefully close the detergent drawer.
ACTIVATING THE APPLIANCE
Press and hold for a couple of seconds the
button to activate or deactivate the appliance.
A tune sounds when the appliance is activated. The
appliance performs a start up animation. The
animation quickly shows each washing programme
and the default temperature and spin settings.
The display shows the word On.
SETTING A PROGRAMME
1. Touch the programme button and set the
programme:
• The indicator of the button flashes.
• The display shows the programme duration.
2. If necessary, change the temperature and the
spin speed or add available options. When you
activate an option, the indicator of the set
option comes on.
If you set something incorrect, the
display shows the message .
11
STARTING A PROGRAMME WITHOUT THE
KLAAR OVER/FINI DANS OPTION
Touch the button .
• The indicator of the button
stops to
flash and stays on.
• The programme starts, the door locks, the
indicator is on.
• The drain pump can operate for a short time
at the beginning of the washing cycle.
After approximately 15 minutes from
the start of the programme:
• The appliance adjusts automatically
the programme duration agree with
the laundry load.
• The display shows the new value.
STARTING A PROGRAMME WITH THE KLAAR
OVER/FINI DANS OPTION
1. Touch the button again and again to
choose the number of hours in which you want
the washing cycle to be finished.
The display shows the number of hours you set
(e.g. ) and the indicator above the button is
on to show that his option is active.
2. Touch the button :
• The door is locked.
• The appliance starts the countdown.
• When the countdown is completed, the
programme starts automatically.
You can cancel or change the set of
the Klaar Over/Fini Dans option before
you touch the button . After
touching the button you can only
cancel the Klaar Over/Fini Dans
option.
To cancel the the Klaar Over/Fini Dans option:
a. Touch the button to set the appliance
to pause. The indicator of button
flashes.
b. Touch the button until the indicator
above this button goes off.
Touch the button again to start the
programme immediately.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before they
operate.
1. Touch
.
The indicator of this button flashes.
2. Change the options. If you change any option
the Klaar Over/Fini Dans option (if set) will be
disabled.
3. Touch
again.
The programme continues.
CANCELLING A PROGRAMME
1. Press the button for some seconds to
cancel the programme and to deactivate the
appliance.
2. Press the same button again to activate the
appliance. Now, you can set a new washing
programme.
Before starting the new programme
the appliance could drain the water. In
this case, make sure that the detergent
is still in the detergent compartment, if
not fill the detergent again.
OPENING THE DOOR
While a programme (or the ) operates, the
appliance door is locked. The indicator is on.
CAUTION! If the temperature and
level of the water in the drum are too
high, you cannot open the door.
To open the door during the first minutes of
the cycle (or when the operates) :
1. Touch the button to pause the appliance.
2. Wait until the indicator goes off.
3. You can open the door.
4. Close the door and touch the button again.
The programme (or the
) continues.
AT THE END OF THE PROGRAMME
• The appliance stops automatically.
• The acoustic signal operates (if it is activated).
• In the display comes on.
• The indicator of the button goes off.
• The door lock indicator goes off.
• You can open the door.
• Remove the laundry from the appliance. Make
sure that the drum is empty.
• Press the button for some seconds to
deactivate the appliance.
• Close the water tap.
12
Loading...