Yokogawa Yokogawa CL155 Manual

User's

CL155

Manual

Clamp-on Tester

クランプテスタ

IM CL155

保証書付

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com

IM CL155

2018.6 10版（ KYOU）

Contents

■ Precautions for Safety Use of the Instrument ……………………………… i

1. Instrument Layout …………………………………………………………… 1

2. Measurement ………………………………………………………………… 3

2.1 Preparation for Measurement ……………………………………………… 3

2.2 Current Measurement ……………………………………………………… 3

2.2.1 AC Current Measurement (Normal Mode) ……………………………… 4

2.2.2 Peak Current Measurement (Peak Mode) ……………………………… 4

2.3 Voltage Measurement ……………………………………………………… 5

2.3.1 DC Voltage Measurement ………………………………………………… 5

2.3.2 AC Voltage Measurement ………………………………………………… 5

2.4 Resistance Measurement …………………………………………………… 6

2.4.1 Resistance Measurement (Normal Mode) ……………………………… 6

2.4.2 Continuity Check (400Ω range fixed) …………………………………… 6

3. Other Functions ……………………………………………………………… 8

3.1 Sleep Function ……………………………………………………………… 8

3.2 Data Hold Function ………………………………………………………… 8

3.3 OUTPUT Terminal (For current measurement only) …………………… 9

3.4 Optional Accessories ……………………………………………………… 10

4. Battery Replacement ……………………………………………………… 11

5. Specifications ……………………………………………………………… 12

6. Calibration and After-sales Service ……………………………………… 15

■PrecautionsforSafeUseoftheInstrument

When handling the instrument, ALWAYS observe all of the cautionary notes on
safety given below. Yokogawa M&C Corporation is not at all liable for damage
resulting from misuse of this product by the user that is contrary to these
cautionary notes.
Various symbols are used on the instrument and in this manual to ensure the
product is used safety and to protect operators and property from possible
hazards or damage. The following safety symbols are used where appropriate.
Read the explanations carefully and familiarize yourself with the symbols
before reading the text.

The instrument and this manual use the following safety symbols:

Danger! Handle with Care.
  This symbol indicates that the operator must refer to an explanation

in the Users Manual in order to avoid the risk of personal injury or
death and/or damage to the instrument.

Double Insulation
 This symbol indicates double insulation.

AC Voltage/Current
 This symbol indicates AC voltage or current.

DC Voltage/Current
 This symbol indicates DC voltage or current.

Ground
 This symbol indicates ground (earth)

This symbol Indicates that this instrument can clamp on bare
conductors when measuring a voltage corresponding to the applicable
Measurement category, which is marked next to this symbol.

WARNING

Indicates that there is a possibility of serious personal injury or loss of life if the
operating procedure is not followed correctly and describes the precautions for
avoiding such injury or loss of life.

CAUTION

Indicates that there is a possibility of serious personal injury of damage to the
instrument if the operating procedure is not followed correctly and describes
the precautions for avoiding such injury or damage.

NOTE

Draws attention to information essential for understanding the operation and
features.

IM CL155

i

WARNING

●Never make measurement on a circuit above 750V AC or 1000V DC.

● Do not use the instrument in an atmosphere where any flammable or

explosive gas is present.

● Do not attempt to make measurement in the presence of flammable gasses,

fumes, vapor or dust. Otherwise, the use of the instrument may cause
sparking, which can lead to an explosion.

● Avoid using the instrument if it has been exposed to rain or moisture or if

your hands are wet.

●Do not exceed the maximum allowable input of any measurement range.

●Never open the battery compartment cover when making measurement.

● Do not use the instrument if there is any damage to the casing or when the

casing is removed.

● Do not turn the Function Selector switch with plugged in test leads

connected to the circuit under test.

● Do not install substitute parts or make any modification to the instrument.

Return the instrument to Yokogawa M&C or your distributor for repair or
re-calibration.

● Always switch off the instrument before opening the battery compartment

cover for battery replacement.

● Do not use the test leads that have deteriorated or are detective.

● Check the test leads continuity

WARNING

To avoid damage to the instrument or electric shock!
The restrictions on the maximum voltage level for which the CL155 testers can
be used, depend on the measurement categories specified by the safety
standards. These category specifications are formulated to protect operators
against transient impulse voltage in power lines.

Maximum Allowable Input

Function

A

V, V

Input terminal-to­ground voltage

IM CL155

MEASUREMENT

CATEGORY II

AC 2000A rms
Measuring circuit
voltage:
AC 750V rms

AC 750V rms
/DC 1000V

AC 750V rms
/DC 1000V

MEASUREMENT

CATEGORY III

AC 2000A rms
Measuring circuit
voltage :
AC 600V rms

AC 600V rms
/DC 600V

MEASUREMENT

CATEGORY Ⅳ

AC 2000A rms
Measuring circuit
voltage :
AC 300V rms

AC 300V rms
/DC 300V

ii

O (None, Other)
  Other circuits that are not directly connected to MEAINS.
Measurement category II (CAT.II)
  Local level, appliance, portable equipment etc., with smaller transient over-

voltages than CAT.III.

Measurement category III (CAT.III):
  Distribution level, fixed installation, with smaller transient over-voltages than

CAT.IV.

Measurement category IV (CAT.IV):
 Outside and service entrance.

CAUTION

● Always make sure to insert each plug of the test leads fully into the

appropriate terminal on the instrument.

● Make sure to remove the test leads from the instrument before making

current measurement.

● Be sure to set the Function Selector switch to the "OFF" position after use.

When the instrument will not be in use for a long period of time, Place it in
storage after removing the battery.

● Use a damp cloth and detergent for cleaning the instrument. Do not use

abrasives or solvents.

NOTE

● Radiation immunity affects the accuracy of CL155 testers under the

conditions specified in EN 61000-4-3.

● If equipment generating strong electromagnetic interference is located

nearly, the testers may malfunction.

IM CL155

iii

1.InstrumentLayout

(1)Transformer Jaws : Pick up current flowing through the conductor.
(2) Open/Close Lever : Operates the transformer jaws. Press to open the

Transformer Jaws.

(3) Function Selector Switch : Selects ranges. Also used to power the

instrument on.

(4) Data Hold Button : Freezes the display reading. " " is shown on the

display when Data Hold is enabled.

(5) Mode Selector Button : On a AC current (" 400A" or " 2000A" or

the resistance ( ) range. Press the mode button to cycle through the
measurement modes. The instrument is initially set to the normal mode and
can be switched to peak or continuity check mode by means of the mode
button.

IM CL155

1

A / V

(ACA/ACV)

  Normal

 ↓

  Peak

Display Display

(Resistance/Continuity)

Resistance
↓

Continuity
  check

Ω

(6) Button : Reset the measurement in peak mode.
(7) LCD Display : Field effect type of liquid crystal display with maximum counts

of 3999. Function symbols and decimal point are controlled by the
microprocessor based on the selected function and measuring mode.

(8) Terminal Cover : Slides over Hi and Lo Terminals to prevent access to them

when OUTPUT terminal is in use.

(9) OUTPUT Terminal (For " 400A" or " 2000A" range only) : Provides DC

voltage output in proportion to the AC or DC current reading. (See section

3.3, OUTPUT Terminal.) The output is connected to a recording device such
as a chart recorder for long hour monitoring. No output is available on
voltage and resistance ranges.

(10) Lo Terminal : Accepts the black test lead for voltage or resistance

measurement.

(11) Hi Terminal : Accepts the red test lead for voltage or resistance

measurement.

(12) Safety Hand Strap : Prevents the instrument from slipping off the hand

during use.

(13) Test Leads (Model 98072) : Connected to Lo and Hi terminals for voltage

or resistance measurement.

(14) Barrier: It is a part providing protection against electrical shock and

ensuring the minimum required air and creepage distances.

IM CL155

2

2.Measurement

2.1PreparationforMeasurement

CAUTION

● The jaw section is a delicate, precision sensor. Do not subject the jaw to

unreasonably strong shock, vibration, or force when using it.

● If dust gets into the tops of the jaws, remove it immediately. Do not close the

jaws when dust is trapped in its joints as the sensor may break.

● Please check that the function and mode are set to the desired setting

before measurement.

2.2CurrentMeasurement

WARNING

● Do not make measurement on a circuit above 750VDC. This may cause

shock hazard or damage to the instrument or equipment under test.

● Do not make current measurement with the test leads connected to the Hi

and Lo terminals.

● When measuring current is not less than 1000A, make sure to stop

measurement within the maximum measuring time shown below. Otherwise,
transformer jaws may heat to cause a fire or deformation of molded parts,
which will degrade insulation.

 1000 to 1500A : 15min. 1500 to 2000A : 5min.

●Keep your fingers and hands behind the barrier during measurement.

IM CL155

3

2.2.1ACCurrentMeasurement(NormalMode)

(1) Set the Function Selector switch to the " 400A" or " 2000A" position.

"AC" should be shown on the upper left corner of the display.

(2) Press the open/close lever to open the transformer jaws and clamp them

onto the conductor under test, then take the reading on the display. The
most accurate reading will be obtained by keeping the conductor at the
center of the transformer jaws.

NOTE

● During current measurement, keep the transformer jaws fully closed.

Otherwise, accurate measurement cannot be made. The maximum
measurable conductor size is approx. 54.5mm in diameter.

● The transformer jaws may buzz when measuring large current. This has no
effect on the instruments performance or safety.

2.2.2PeakCurrentMeasurement(PeakMode)

(1) Set the Function Selector switch to the "

400A" or " 2000A" position.

(2) Press the button once to enter from the normal mode to the PEAK

mode. " " should be shown on the display.

(3) Press the open/close lever to open the transformer jaws and clamp them

onto the conductor under test. Then, press the button.

(4) The display shows the currents crest value divided by the square root of

two. Therefore, when the current is sinusoidal, the reading equals RMS
value.

(5) To reset the display, press the button.

(6) After the measurement is over, press the

button to return to the

normal mode.

NOTE

● In the Peak measurement mode, the data hold feature is disabled.

● In the Peak measurement mode, the response time is 10ms.

IM CL155

4

2.3VoltageMeasurement

WARNING

Do not make measurement on a circuit above 750V AC or 1000V DC. This
may cause shock hazard or damage to the instrument or equipment under
test.

2.3.1DCVoltageMeasurement

(1) Set the Function Selector switch to the " V " position. "DC" should be shown

on the upper left corner of the display.

(2) Slide the terminal cover to the left to disclose the Hi and Lo terminals. Plug

the red test lead into the Hi terminal and the black test lead into Lo terminal.

(3) Connect the tip of the red and black test leads to the positive (+) and

negative (-) sides of the circuit under test respectively. Take the reading on
the display.

2.3.2ACVoltageMeasurement

(1) Set the Function Selector switch to the " V " position. "AC" should be shown

on the upper left corner of the display.

(2) Slide the terminal cover to the left to disclose the Hi and Lo terminals. Plug

the red test lead into the Hi terminal and the black test lead into Lo terminal.

(3) Connect the tip of the test leads to the circuit under test respectively. Take

the reading on the display.

NOTE
For high sensitivity, there are parts which do not indicate "0".

IM CL155

5

2.4ResistanceMeasurement(NormalMode)

WARNING

Never use the instrument on an energized circuit.

2.4.1ResistanceMeasurement(NormalMode)

(1) Set the Function Selector switch to the "

" position. The "Ω" should be

shown on the upper right corner of the display.

(2) Slide the terminal cover to the left to disclose the Hi and Lo terminals. Plug

the red test lead into the Hi terminal and the black test lead into the Lo

terminal. Check that "OL" (over indication) is indicated on the LCD display.
(3) Short the tip of the test leads and check whether the display reads "0".
(4) Connect the tip of the test leads to the circuit under test respectively. Take

the reading on the display.

NOTE
When shorting the tip of the test leads, the display may read a very small
resistance instead of "0". This is the resistance of the test leads on the display.

2.4.2ContinuityCheck(400Ωrangefixed)

The continuity check mode is enabled by pressing the

button on

resistance range. " " andΩis indicated on the display to show the
instrument in the continuity check mode. The buzzer beeps, if the resistance
under test is 50Ω or less.

(1) Set the Function Selector switch to the " " position.
(2) Slide the terminal cover to the left to disclose the Hi and Lo terminals. Plug

the red test lead into the Hi terminal and the black test lead into the Lo

terminal. Check that "OL" (over indication) is indicated on the LCD display.

IM CL155

6

(3) Press the

button once to enter from the normal mode to the

continuity check mode. " " should be indicated on the display.
(4) Short the tip of the test leads and check whether the display reads "0".
(5) Connect the tip of the test leads to the circuit under test. If the resistance is

50Ω or less, the buzzer beeps.

NOTE
When shorting the tip of the test leads, the display may read a very small
resistance instead of "0". This is the resistance of the test leads on the display.

IM CL155

7

3.OtherFunctions

3.1SleepFunction

This is a function to prevent the instrument from being left powered on in order
to conserve battery life. This function causes the instrument to enter the Sleep
(powered-down) mode about 10 minutes after the last switch or button
operation.

To exit the Sleep mode, press the Data hold
turn the Function Selector switch back to "OFF", then to any other position, or
press any button.
The current is consumed a little in the Sleep mode.

HowtoExittheSleepMode

Turn the Function Selector switch from "OFF" to another position with the data
hold function button pressed. Then, "P.OFF" is shown on the display. This
disables the sleep function and enables continuous use of the instrument.

NOTE

● Connecting the plug to the OUTPUT terminal disables the Sleep function.

The function is enabled on removing the plug from the terminal.

● The Sleep function is disabled in the PEAK measurement mode.

3.2DataHoldFunction

This is a function used to freeze the measured value on the display. Press the
Data Hold button to freeze the reading. The reading will be held regardless of
subsequent variation in input. " " is shown on the upper right corner of the
display while the instrument is in the Data Hold mode.
To exit the Data Hold mode, press the Data Hold button again.

button or button or

NOTE

● The Data hold function is disabled in the peak measurement mode on the

AC current range.

● When the Sleep function is activated, the Data hold mode turns to the

normal mode.

IM CL155

8

3.3OUTPUTTerminal(Forcurrentrangesonly)

WARNING

● Never use the instrument on a circuit above 750VAC or 1000VDC. This

may cause electrical shock hazard and damage to the instrument or the
circuit under test.

● Never apply voltage to the OUTPUT terminal.

Only on the " 400A" or " 2000A" range, DC voltage proportional to the input
current is output from the OUTPUT terminal.

(1) Attach the output plug cable (sold separately : 98076 or 98077) to a

connection lead so that the output voltage can be connected to a recording
device such as a chart recorder.

(2) Slide the terminal cover to the right to disclose the OUTPUT terminal and

insert the output plug into the terminal. Make connection to the recording

device.

(3) Set the Function Selector switch to the " 400A" or " 2000A" position and

follow appropriate measurement instructions.

NOTE

● Output voltage is 1mV/A on the " 400A" range and 0.1mV/A on

the " 2000A" range. Set an appropriate input sensitivity on the recorder.

● The peak hold function does not apply to the recorder output even if the

instrument is in the peak hold mode.

● For long term measurement, disable the sleep function.

IM CL155

9

3.4OptionalAccessories

Clamp Adapter Model 99025 (For AC current measurement only)
The clamp adapter (99025) has been discontinued.

The clamp adapter (99025) is designed to increase the measuring capability of
a clamp meter. With the use of the Clamp Adapter, you can not only extend
current range over 3000A, but also clamp on a large bus-bar or conductor.
(1) Set the Function Selector switch to the "

A " position.

(2) As shown in the figure below, clamp Model CL155 onto the pickup coil of

Model 99025.
(3) Clamp Model 99025 onto the bus-bar or conductor under test.
(4) Take the reading on Model CL155 and multiply it by 10.

IM CL155

10

4.BatteryReplacement

WARNING

To avoid electric shock hazard, make sure to set the Function Selector switch
to "OFF" and remove the test leads from the instrument before trying to
replace battery.

CAUTION

● Do not mix new and old batteries.

● Make sure to install battery in correct polarity as indicated in battery

compartment.

If the battery voltage becomes too low for the instrument to operate normally,
"

" is shown on the display. Then, replace the battery. Note that when the
battery is completely exhausted, the display blanks without " " shown.
(1) Set the Function Selector switch to the "OFF" position.
(2) Unscrew and remove the battery compartment on the bottom of the

instrument.
(3) Replace the battery observing correct polarity. Use two new R6P batteries.
(4) Re-place and screw the battery compartment cover.

IM CL155

11

5.Specifications

■ Instrument Specifications

● Measuring Ranges and Accuracy (at 23 ±5℃, 45 to 75% relative humidity)

AC Current

Ranges

400A 0 to 400.0A 0.1A

0 to 1000A

2000A

Conversion method : AC coupled, true rms responding, calibrated to the rms
*1 : 400A range : 5 to 100% of range , 2000A range : 200A to 2000A

1000 to 1500A 15min.
1500 to 2000A ±3.0% rdg (50/60Hz) 5min.

AC Voltage ( V) Auto-ranging

Range Measuring range
40V 0 to 40.00V 0.01V
400V 15.0 to 400.0V 0.1V
750V 150 to 750V 1V

Conversion method : AC coupled, true rms responding, calibrated to the rms
Initially set to the 40V range. Input impedance is about 1MΩ.

DC Voltage ( V) Auto-ranging

Range Measuring range Resolution Accuracy
40V 0 to ±40.00V 0.01V

1000V 150 to ±1000V 1V

Initially set to the 40V range. Input impedance is about 1MΩ.

400A, 2000A

Measuring

range

Resolution

1A

Accuracy (frequency range)

±1.0% rdg ±3dgt (50/60Hz) *1
±2.0% rdg ±3dgt (40 to 1kHz)

±1.0% rdg ±3dgt (50/60Hz) *1
±3.0% rdg ±3dgt (40 to 1kHz)

Resolution

Accuracy

±1.0% rdg ±2dgt (50/60Hz)
±1.5% rdg ±3dgt (40 to 1kHz)

±1.0% rdg ±2dgt400V 15.0 to ±400.0V 0.1V

Maximum

Measurement

Time

Continuous

Resistance (Auto-ranging)

Range Measuring range Resolution Accuracy

Ω 0 to 400.0Ω 0.1Ω

400

Ω 0.150 to 4.000kΩ 1Ω

4k
40kΩ 1.50 to ±40.00kΩ 10Ω

±1.5% rdg ±2dgt

400kΩ 15.0 to ±400.0kΩ 100Ω

Initially set to the 400Ω range. In the continuity check mode, fixed to the 400Ω range
and when the reading is not more than . 50 ±35Ω, the buzzer beeps.

IM CL155

12

Peak Current (10ms)

Range Measuring range Accuracy (Frequency Range)

400A 0 to 400.0A

2000A

0 to 1500A

±3.0% rdg ±6dgt (50/60Hz)
±3.0% rdg ±10dgt (40 to 1kHz)

±4.0% rdg ±6dgt (50/60Hz)
±4.0% rdg ±10dgt (40 to 1kHz)

1500 to 2000A ±4.5% rdg (50/60Hz)

OUTPUT (AC Current Ranges)
DC Output : 100.0mV per 1000 counts (Output impedance : about 10k

Ω)

Range Measuring range Accuracy (Frequency Range)
400A 0 to 400.0mV/0 to 400A ±1.5% rdg ±0.5mV (50/60Hz) *1

±2.5% rdg ±0.5mV (40 to 1kHz)

2000A 0 to 150.0mV/0 to 1500A ±1.5% rdg ±0.5mV (50/60Hz) *1

±3.5% rdg ±0.5mV (40 to 1kHz)

150.0 to 200.0mV/1500 to 2000A

*1 : 400A range : 5 to 100% of range , 2000A range : 200A to 2000A

±3.5% rdg (50/60Hz)

■GeneralSpecifications

● Operating System : Dual integration

● Measurement Function : AC current, DC current, AC voltage, resistance,

continuity check

● Display : Liquid crystal display with maximum counts of 3999

● Overrange Indication : "OL" is shown on the display

● Response Time : Approx. 2 seconds.

● Temperature and Humidity for Guaranteed Accuracy : 23℃ ±5℃, relative

humidity 45 to 75% without condensation

● Operating Temperature and Humidity : 0 to 40℃, relative humidity up to 85%

without condensation

● Storage Temperature and Humidity : -20 to 60℃, relative humidity up to 85%

without condensation

● Effect of conductor position : At every part inside the jaws

Range Measuring range Conductor size Effect of conductor position
400A 0 to 400A φ10mm or less ±2.0%rdg±3dgt

2000A

0 to 1500A φ25mm or less ±2.0%rdg±3dgt
1500 to 2000A φ25mm or less ±5.0%rdg

● Effect of external magnetic field : 1A or less in AC or DC magnetic field of

400 A/m

IM CL155

13

● Power Source : Two R6P 1.5V battery

● Battery Life : Approx. 80 hours (continuity)

● Current Consumption : Approx. 7mA max. (Sleep function : Approx. 20μA)

● Sleep function : Automatically powered down in Approx. 10 minutes after the

last switch operation

● Withstanding Voltage : 6300V AC, 50/60Hz for 5 sec. between electrical

circuit and housing case or metal part of the jaws

● Insulation Resistance : 50MΩ or greater at 1000V between electrical circuit

and housing case or metal part of the jaws

● Conductor Size : Approx. 54.5mm diameter max.

● Dimensions : Approx.105(W) x 247(H) x 49(D) mm

● Weight : Approx. 470g (with batteries)

● Safety Standard: EN 61010-1, EN 61010-2-033
         EN 61010-031, EN 61010-2-032
         AC/DC300V CAT IV,AC/DC 600V CAT III,
          AC/DC 1000V CAT II, Pollution degree2, indoor use

altitude 2000m or less

● EMC Standard : EN 61326-1, EN 61326-2-1

● Radiation immunity : EN 61000-4-3

● Environmental standard: EN 50581

● Accessories : Test leads Model 98072 1set
        R6P batteries 2
        Carrying case Model 93034 1
        Users Manual 1

● Optional Accessories : Output cable Model 98076

Output cable (for terminal screw) Model 98077

6.CalibrationandAfter-salesService

Should any failure occur while you are using the tester, follow the instructions
given below. If the tester still fails to operate correctly and needs repair, contact
the vendor from whom you purchased the instrument or the nearest Yokogawa
Meters & Instruments sales office.

● Turn off the POWER switch once, then turn it back on again.

● If the tester does not turn on, replace the battery with a new one.

Calibration
It is recommended that the instrument be calibrated once every year.

IM CL155

14

This manual is valid only in China.

产品中有害物质的名称及含量

有害物质

表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572
规定的限量要求以下。

表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572
规定的限量要求。

IM CL155

15