Yamaha RX-V740RDS User Manual

RX-V740RDS

AV Receiver Ampli-tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool,

dry, clean place — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid humming sounds.

Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may

fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: – Other components, as they may cause damage

and/or discoloration on the surface of this unit.

–

Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall

and liquid may cause electrical shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.

To prevent damage by lightning, disconnect the power cord from the wall outlet during an electrical storm.

14 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods

of time (i.e. vacation), disconnect the AC power plug from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that this unit is faulty.

17 Before moving this unit, press STANDBY/ON to set

this unit in standby mode, and disconnect the AC power plug from the wall outlet.

VOLTAGE SELECTOR (China and General models only) The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called standby mode. In this state, this unit is designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note

• The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

■ Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.

CAUTION

CONTENTS

INTRODUCTION

CONTENTS ............................................................ 1

FEATURES ............................................................. 2

GETTING STARTED ............................................ 3

Supplied accessories .................................................. 3

Installing batteries in the remote control ...................3

CONTROLS AND FUNCTIONS ......................... 4

Front panel................................................................. 4

Remote control .......................................................... 6

Front panel display .................................................... 8

PREPARATION

CONNECTIONS .................................................... 9

Before connecting components ................................. 9

Connecting video components ................................ 10

Connecting audio components ................................ 12

Connecting the antennas.......................................... 13

Connecting an external amplifier ............................ 14

Connecting an external decoder .............................. 14

Connecting the speakers ..........................................15

Connecting the power supply cords ........................ 18

Turning on the power .............................................. 18

ON-SCREEN DISPLAY (OSD) .......................... 19

BASIC SYSTEM SETTINGS ............................. 20

Using the basic menu .............................................. 20

Setting the unit to match your speaker system ........ 22

Setting speaker output levels (SP LEVEL) ............. 22

ADVANCED OPERATION

SET MENU ........................................................... 41

Set menu list ............................................................ 41

Adjusting the items on the set menu ....................... 41 SOUND 1 SPEAKER SET

(speaker mode settings) ....................................... 42

SOUND 2 SP DISTANCE (speaker distance) ........ 44

SOUND 3 LFE LEVEL .......................................... 44

SOUND 4 D. RANGE (dynamic range) ................. 44 SOUND 5 CENTER GEQ

(center graphic equalizer) .................................... 45 SOUND 6 HP TONE CTRL

(headphone tone control) .................................... 45 INPUT 1 I/O ASSIGN (input/output assignment) .. 45

INPUT 2 INPUT MODE (initial input mode) ........ 46

INPUT 3 INPUT RENAME.................................... 46

OPTION 1 DISPLAY SET ......................................46

OPTION 2 MEM. GUARD (memory guard) ......... 47

OPTION 3 AUDIO MUTE ..................................... 47

OPTION 4 ZONE SET ........................................... 47

REMOTE CONTROL FEATURES ................... 48

Control area ............................................................. 48

Setting the manufacturer code .................................49 Changing the source name in the display window ..50 Clearing renamed source names, and setup

manufacturer codes ............................................. 51

Controlling other components .................................52

SETTING THE SPEAKER LEVELS ................ 53

Adjusting the volume during playback ................... 53

Using the test tone ................................................... 53

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

BASIC OPERATION

PLAYBACK ..........................................................23

Input modes and indications .................................... 25

Selecting a sound field program ..............................26

DIGITAL SOUND FIELD PROCESSING (DSP)

............................................................................ 29

Understanding sound fields ..................................... 29

Hi-Fi DSP programs ................................................29

CINEMA-DSP ...................................................... 30

Sound design of CINEMA-DSP ............................. 30

CINEMA-DSP Programs ........................................ 30

Sound field effects ................................................... 32

TUNING ................................................................ 33

Presetting stations .................................................... 34

Selecting a preset station ......................................... 36

RECEIVING RDS STATIONS ........................... 37

Description of RDS data ......................................... 37

Changing the RDS mode .........................................37

PTY SEEK function ................................................ 38

EON function .......................................................... 38

SLEEP TIMER ..................................................... 39

RECORDING ....................................................... 40

ADDITIONAL INFORMATION

SOUND FIELD PROGRAM PARAMETER

EDITING .......................................................... 54

What is a sound field? ............................................. 54

Sound field program parameters ............................. 54

Changing parameter settings ................................... 55

Digital Sound Field Parameter Descriptions ...........56

TROUBLESHOOTING....................................... 60

GLOSSARY .......................................................... 64

SPECIFICATIONS .............................................. 66

INFORMATION

ADDITIONAL

English

FEATURES

Built-in 6-channel power amplifier

◆ Minimum RMS output power

(0.06% THD, 20 Hz – 20 kHz, 8Ω) Main: 90 W + 90 W Center: 90 W Rear: 90 W + 90 W Rear center: 90 W

Multi-mode digital sound field processing

◆ Dolby Pro Logic/Dolby Pro Logic II decoder

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6

Decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

technology and Dolby Pro Logic, Dolby Digital or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station random access preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (Preset editing)

Other features

◆ 96 kHz/24-bit D/A converter

◆ Set menu for optimizing this unit for your Audio/

Video system

◆ Test tone generator for easier speaker balance

adjustment

◆ 6-channel external decoder input

◆ On screen display function helpful in controlling this

unit

◆ Component video input/output capability

◆ S-video signal input/output capability

◆ Optical and coaxial digital audio signal jacks

◆ Video Conversion (Composite Video ⇔ S Video)

◆ Sleep timer

◆ Remote control with preset manufacturer codes

◆ Zone B capability

■ About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part for the reason of the improvement in operativity ability, and others. In this case, the product has priority.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.

“DTS”, “DTS-ES Extended Surround” and “Neo:6” are trademarks of Digital Theater System, Inc.

GETTING STARTED

Supplied accessories

After unpacking, check that the following parts are contained.

Remote control

TRANSMIT

RE-NAME

CLEAR

SYSTEM

POWER

V-AUX

D-TV/CBL VCR 1 VCR2/DVR DVD

POWER

REC

DISC SKIP

LEVEL

TITLE

TV INPUT

PRESET PRESET

TEST

HALL JAZZ CLUB

1234

MUSIC VIDEOTVTHEATER

5678

/DTS

SUR.

9101112

CODE SET

6CH INPUT

STANDBY

SLEEP

PHONO

MD/CD-R

TUNER

SELECT

POWER

AMP

AUDIO

VOL

MUTE

SET MENU

TV VOL

A/B/C/D/E

TV MUTE

SELECT

ON SCREEN

STEREO

TV VOL

DISPLAYRETURN

EFFECT

ROCK

ENTER-

CONCERT

TAINMENT

MOVIE

THEATER 1

THEATER 2

6.1/5.1

NIGHT

CHP/INDEX

Batteries (4) (AAA, R03, UM-4)

75-ohm/300-ohm antenna adapter (U.K. model)

Installing batteries in the remote control

Insert the batteries in the correct direction by aligning the + and – marks on the batteries with the polarity markings (+ and –) inside the battery compartment.

INTRODUCTION

AM loop antenna

Indoor FM antenna (U.S.A., Canada, China, Korea and General models)

(Europe, U.K., Australia and Singapore models)

■ Notes on batteries

• Change all of the batteries if you notice a decrease in the operating range of the remote control, that the indicator does not flash, or the light becoming dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color.

• If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

1 Press the part marked with a and slide off

the battery compartment cover.

2 Insert the four batteries supplied (AAA, R03,

UM-4) according to the polarity markings on the inside of the battery compartment.

3 Slide the cover back on so that it snaps into

place.

If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries, set up the manufacturer code and program any acquired functions that may have been cleared.

English

CONTROLS AND FUNCTIONS

Front panel

1 32 4 8756 q90

INPUT

RDS MODE/FREQ

STANDBY

/ON

6CH INPUTINPUT MODE

SILENT

PHONES

w r y

epo

PTY SEEK

MODE START

EFFECT

RDS MODE/FREQ

MODE START

EON

PROGRAMSTEREOSPEAKERS

A/B/C/D/E

t iu

EON

PTY SEEK

NEXT SET MENU

a s fd

(U.K. and Europe models only)

1 STANDBY/ON

Turns the unit on, or sets it in standby mode. When you turn the unit on, you will hear a click and there will be a 4 to 5-second delay before it can reproduce sound.

Standby mode

In this mode, the unit uses a small amount of power in order to receive infrared-signals from the remote control.

VOLUME

FM/AM

PRESET/TUNING

EDIT

TUNING MODE MEMORY

AUTO/MANUAL MONO

MAN`L/AUTO FM

PRESET/TUNING

VIDEO AUX

OPTICALRAUDIOLVIDEOS VIDEO

BASS

5 Remote control sensor

Receives signals from the remote control.

6 Front panel display

Shows information about the operational status of the unit.

7 TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual.

TREBLE

2 INPUT MODE

Sets the priority for the types of input signals (AUTO, DTS, ANALOG) received when one component is connected to two or more input jacks. You cannot set priority for an audio source if you have selected 6CH INPUT as the input source.

3 INPUT

Selects the input source you want to listen to or watch.

4 6CH INPUT

Selects the audio source connected to the 6CH INPUT jacks. This selection takes priority over sources selected with INPUT (or the input selector buttons on the remote control).

8 PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h between selecting a preset station number and tuning (the colon (:) turns on or off). This button is also used to exchange the assignment of two preset stations with each other.

9 FM/AM

Switches the reception band between FM and AM.

0 MEMORY (MAN’L/AUTO FM)

Stores the current station in memory.

q VOLUME

Controls the output level of all audio channels. This does not affect the OUT (REC) level.

w SILENT (PHONES jack)

Allows you to enjoy DSP effects when listening with headphones. When you connect headphones to the headphone jack, no signals are output to the speakers or the OUTPUT jacks.

e SPEAKERS A/B

Turns the set of main speakers connected to the A and/or B terminals on or off.

CONTROLS AND FUNCTIONS

(U.K. and Europe models only)

a RDS MODE/FREQ

Press this button when the unit is receiving an RDS station, to cycle the display mode among PS mode, PTY mode, RT mode, CT mode (if the station offers those RDS data service) and/or frequency display mode in turn.

INTRODUCTION

r STEREO/EFFECT

Switches between normal stereo and DSP effect reproduction. When you select STEREO, the unit mixes down all Dolby Digital and DTS signals (except the LFE channel) as well as those 2-channel signals without effects, to the main left and right speakers.

t PROGRAM l / h

Select the DSP program.

y A/B/C/D/E

Selects preset station groups A to E when the unit is in tuner mode.

Selects the set menu mode when the unit is not in tuner mode.

u PRESET/TUNING l / h

Select preset station numbers 1 to 8 when a colon (:) is displayed in the front panel display. Select the tuning frequency when a colon (:) is not displayed when the unit is in tuner mode.

SET MENU –/+

Adjust settings on the set menu when the unit is not in tuner mode.

i VIDEO AUX jacks

Inputs for audio and video signals from a portable external source (game console, etc.). Set the input source to V-AUX to select source signals from these jacks.

s PTY SEEK MODE

Press this button to set the unit in the PTY SEEK mode.

d PTY SEEK START

Press this button to begin searching for a station after the desired program type has been selected in the PTY SEEK mode.

f EON

Press this button to select a radio program type (NEWS, INFO, AFFAIRS, SPORT) to tune in automatically.

o BASS

Adjusts the low-frequency response for the main left and right channels. Turn right to increase or left to decrease the lowfrequency response.

p TREBLE

Adjusts the high-frequency response for the main left and right channels. Turn right to increase or left to decrease the highfrequency response.

English

CONTROLS AND FUNCTIONS

Remote control

This section describes the controls and functions of the remote control. Make sure that the AMP mode is selected before use.

1 2

TRANSMIT

SYSTEM

POWER

STANDBY

RE-NAME

SLEEP

CLEAR

CODE SET

6CH INPUT

w e

r t

PHONO

TUNER

TV VOL

TV MUTE SELECT

TV VOL

MD/CD-R

POWER

A/B/C/D/E

CONCERT

THEATER 1

V-AUX

D-TV/CBL VCR 1 VCR2/DVR DVD

POWER

REC

DISC SKIP

LEVEL

TITLE

TV INPUT

PRESET PRESET

TEST

HALL JAZZ CLUB

1234

MUSIC

VIDEOTVTHEATER

5678

/DTS

SUR.

9101112

AUDIO

SET MENU

ON SCREEN

DISPLAYRETURN

ROCK

MOVIE

NIGHT

SELECT

AMP

VOL

MUTE

STEREO

EFFECT

ENTER-

TAINMENT

MOVIE

THEATER 2

6.1/5.1

CHP/INDEX

p a

f g

1 Infrared window

Outputs infrared control signals. Aim this window at the component you want to operate.

2 TRANSMIT indicator

Flashes while the remote control is sending signals.

3 STANDBY

Sets the unit in standby mode.

4 SYSTEM POWER

Turns on the power of the unit.

5 Å/ı/Ç

Sets the remote control to operate other components (not necessarily connected to this unit) without changing this unit’s input source.

6 Input selector buttons

Select the input source and set the remote control to operate the selected source component.

7 Display window

Shows the source component you are currently controlling.

8 LEVEL

Selects the effect speaker channel to adjust.

9 Multi control section

Used to change and implement settings.

0 TEST

Outputs a test tone for use when adjusting the speaker levels.

q DSP program

Select DSP programs when the remote control is in AMP mode. Press one of these buttons repeatedly to select a DSP program within a program group.

w RE-NAME

Used to change the input source name in the display window.

e CLEAR

Used to clear functions acquired using the rename features, and to set manufacturer codes.

r CODE SET

Used to set up manufacturer codes (see page 49).

t SLEEP

Sets the sleep timer.

y 6CH INPUT

Selects the audio source connected to the 6CH INPUT jacks.

CONTROLS AND FUNCTIONS

u SELECT k/n

Set the remote to control a component other than the one selected with the input selector buttons.

i AMP

Switches the function of the same controls between AMP and the component selected using the input selector buttons.

o VOL +/–

Increase or decrease the volume level.

p MUTE

Mutes the sound. Press again to restore the audio output to the previous volume level.

a SET MENU

Selects the set menu mode.

s ON SCREEN

Displays the input or operation status on the on-screen display.

d STEREO/EFFECT

Switches between normal stereo and DSP effect reproduction. When you select STEREO the unit mixes down all Dolby Digital and DTS signals (except the LFE channel) as well as those 2-channel signals without effect sounds, to the main left and right speakers.

f 6.1/5.1

Switches the Dolby Digital EX or DTS ES decoder on or off.

■ Using the remote control

INPUT

STANDBY

/ON

6CH INPUTINPUT MODE

SILENT

EFFECT

PHONES

PRESET/TUNING

A/B/C/D/E

PROGRAMSTEREOSPEAKERS

SET MENU

30° 30°

CODE SET

The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the main unit during operation.

VOLUME

PRESET/TUNINGFM/AM

EDIT

TUNING MODEMEMORY

AUTO/MANUAL MONO

MAN`L/AUTO FM

TREBLE

BASS

VIDEO AUX

OPTICALRAUDIOLVIDEOS VIDEO

Approximately 6 m (20 feet)

■ Handling the remote control

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types of conditions: – high humidity or temperature such as near a heater,

stove or bath; – dusty places; or – in places subject to extremely low temperatures.

INTRODUCTION

g NIGHT

Sets the unit in night listening mode.

English

CONTROLS AND FUNCTIONS

Front panel display

DISCRETEMATRIX

DIGITAL

PCM

VCR2/DVR

VIRTUAL

SILENT

EX PL PL

SP A B

~~~~~~~~~~~~~~

NIGHT HiFi

V-AUXVCR1

DSP

90qw yer uiop

D-TV/CBL

DVD

MD/CD-R

1 Processor indicators

The indicators for the various decoders light up when the decoders are in use.

2 VIRTUAL indicator

Lights up when using Virtual CINEMA DSP.

e HiFi DSP indicator

Lights up when you select a Hi-Fi DSP sound field program.

r CINEMA DSP indicator

Lights up when you select a CINEMA DSP sound field

TUNER CD PHONO

VOLUME

MUTE

AUTO

STEREO

CTRTPTYPS

HOLDPTYEON

(U.K. and Europe models only)

SLEEP

MEMORYTUNED

m dB

L C R

RLLFE RC RR

program.

3 Headphones indicator

Lights up when headphones are connected to the headphone jack.

t Multi-information display

Shows the current DSP program name and other information when you are adjusting or changing settings.

4 Input source indicator

Highlights the current input source with a cursor.

y STEREO indicator

Lights up when the unit is receiving a strong signal from

5 Sound field indicator

a FM stereo broadcast while the “AUTO” indicator is lit. Displays the sound field management the unit is using when you listen to a DSP sound field program.

u TUNED indicator

Lights up when this unit is tuned to a radio station.

6 AUTO indicator

Shows that this unit is in the automatic tuning mode.

i MEMORY indicator

Flashes to show a station can be stored in memory.

7 MUTE indicator

Flashes while the MUTE function is on.

o SLEEP indicator

Lights up while the sleep timer is on.

8 VOLUME level indicator

Indicates the volume level.

p LFE indicator

Lights up when the input signal contains an LFE signal.

9 PCM indicator

Lights up when this unit is reproducing PCM (pulse code modulation) digital audio signals.

a Input channel indicator

The indicators for the appropriate sound channels light up

when a digital signal from a source is played back.

0 SILENT indicator

Lights up when headphones are connected and the digital sound field processor is on.

s RDS indicator (U.K. and Europe models only)

The name(s) of the RDS data offered by the currently

received RDS station light(s) up.

q SP A B indicator

Lights up to indicate which set of main speakers is selected. Both indicators light up when both sets of speakers are selected.

EON indicator lights up when an RDS station that offers

the EON data service is being received.

PTY HOLD indicator lights up while searching for

stations in the PTY SEEK mode.

w NIGHT indicator

Lights up when the unit is set to night listening mode.

CONNECTIONS

Before connecting components

CAUTION

Do not connect this unit or other components to the mains power until all connections between the components have been completed.

• Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some components require different connection methods and have different jack names. Refer to the operation instructions for each component you wish to connect to this unit.

• After you have completed all connections, check them again to make sure they are correct.

• The jack names correspond to the names on the input selector.

This jack is reserved for factory use. Do not connect any equipment to this jack.

DIGITAL INPUT jacks (pages 9 – 12)

Audio component jacks (page 12)

Video component jacks (pages 10 – 11)

OUTPUT jacks (page 14)

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables. You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. Use digital connections if you wish to enjoy the multi-channel sound track of DVD material, etc. with DSP effects. All digital input jacks are acceptable for 96 kHz sampling digital signals.

Note

• The OPTICAL jacks on this unit conform to the EIA standard. If you use a fiber optic cable that does not conform to this standard this unit may not function properly.

SUBWOOFER OUTPUT jack (page 17)

PREPARATION

SIGNAL

GND

PHONO

DIGITAL

INPUT

COAXIAL

OPTICAL

D-TV/CBL

(PLAY)

/CD-R

OUT

DVD

(REC)

MAIN

MD/CD-R

SURROUND

MD/CD-R

OPTICAL

SUB

WOOFER

6CH INPUT

CENTER

DIGITAL OUTPUT

6CH INPUT jacks

(page 14) DIGITAL OUTPUT jack (page 12)

VIDEOAUDIOAUDIO

MONITOR OUT

S VIDEOVIDEO

DVD

D-TV /CBL

VCR-1

OUT

VCR 2 /DVR

OUT

S VIDEOVIDEO

Antenna input terminals (page 13)

COMPORNENT VIDEO

DVD

D-TV

/CBL

MONITOR

OUT

TUNER

ANT

GND

75Ω UNBAL.

FM ANT

MAIN

R L

OUTPUT

CENTER

SUB

REAR

(SURROUND

)

WOOFER

CENTER

SPEAKERS

MAIN

Speaker terminals (page 17)

R L

REAR

(SURROUND)

CENTER

REAR

AC OUTLETS (page 18)

English

CONNECTIONS

Connecting video components

Refer to the connection examples on the next page.

■ Types of video jacks

S VIDEOVIDEO

1 2 3

1 VIDEO jack

Conventional composite video signal.

2 S VIDEO jack

Transmits color and luminance separately and achieves high-quality color reproduction.

3 COMPONENT VIDEO jacks

Transmit color difference (P separately and provide the best quality picture.

Use the commercially available cable type specified for connecting each jack.

• Signals received through the S VIDEO input jacks can be converted to composite signals in this unit and output through its VIDEO MONITOR OUT as well.

• (With the exception of China and General models) Signals received through the VIDEO jack on this unit can be output through the S VIDEO MONITOR OUT jack by setting “V CONV.” in “OPTION 1 DISPLAY SET” on the set menu to ON.

• When the unit receives signals through both S VIDEO and VIDEO jacks, signals input through the S VIDEO jack have priority.

• You can designate the input for the COMPONENT VIDEO A and B jacks to suit your components by using “INPUT 1 I/O ASSIGNMENT” on the set menu.

COMPONENT VIDEO

RPB

B, PR) and luminance

■ Connecting a DVD player/digital TV/cable

Connect the optical digital audio signal output jack on your component to the DIGITAL INPUT jack and connect the video signal output jack on the component to the VIDEO jack on this unit.

• Use the AUDIO jacks on this unit for a video component which does not have optical digital output jack. However, multi-channel reproduction cannot be obtained with audio signals input from the AUDIO jacks.

■ Connecting a recording component

Connect the audio signal input jacks on your video component to the AUDIO OUT jacks on this unit. Then connect the video signal input jack on the video component to the VIDEO OUT jack on this unit for picture recording. Connect the audio signal output jacks on your component to the AUDIO IN jacks on this unit. Then connect the video signal output jack on the component to the VIDEO IN jack on this unit to play a source from your recording component. A second VCR or DVD recorder can be connected using the VCR 2/DVR jacks.

Note

• Once you have connected a recording component to this unit, keep its power turned on while using this unit. If the power is off, this unit may distort the sound from other components.

Signal flow inside this unit

Output

Input

COMPONENT VIDEO

S VIDEO

VIDEO

Only when “V CONV.” in “OPTION 1 DISPLAY SET” is set to ON on the set menu.

(MONITOR OUT)

■ Connecting a video monitor

Connect the video input jack on your video monitor to the MONITOR OUT VIDEO jack.

Note

• If you connect this unit with a source component using Component video jacks, you also need to connect your video monitor using Component video jacks.

R E

OPTICAL OUTPUT

DVD player

L R

AUDIO OUTPUT

VIDEO OUTPUT

OPTICAL OUTPUT

AUDIO OUTPUT

CONNECTIONS

TV/digital TV/

cable TV

VIDEO OUTPUT

PREPARATION

SIGNAL

GND

DIGITAL

INPUT

COAXIAL

OPTICAL

D-TV/CBL

DVD

MD/CD-R

OPTICAL

DIGITAL

OUTPUT

PHONO

(PLAY)

/CD-R

OUT

(REC)

MAIN

SURROUND

AUDIO OUTPUT

SUB

WOOFER

6CH INPUT

CENTER

LR LR

MONITOR OUT

AUDIO INPUT

indicates audio signal direction

indicates left analog cables

indicates right analog cables

indicates optical cables

/CBL

VCR-1

VCR 2 /DVR

COMPORNENT VIDEO

VIDEO INPUT

OUTPUT

MAIN

REAR

(SURROUND

MAIN

VIDEO INPUT

REA

CENT

)

DVD

VIDEOAUDIOAUDIO

DVD

D-TV

OUT

S VIDEOVIDEO

D-TV

/CBL

MONITOR

OUT

TUNER

AM ANT

GND

75Ω UNBAL.

ANT

S VIDEOVIDEO

VIDEO OUTPUT

Video monitorVCR

indicates video signal direction

English

CONNECTIONS

Connecting audio components

■ Connecting a CD player

Connect the coaxial digital output jack on your CD player to the DIGITAL INPUT CD jack on this unit.

• Use the AUDIO jacks on this unit for a CD player which does not have coaxial digital output jack.

■ Connecting a CD recorder or MD

recorder

Connect the optical digital signal input jack on your CD recorder or MD recorder to the DIGITAL OUTPUT MD/ CD-R jack on this unit for digital recording. Connect the optical digital output jack on your CD recorder or MD recorder to the DIGITAL INPUT MD/ CD-R jack on this unit to play a source from your recording component.

• Use the AUDIO jacks on this unit for a CD recorder or MD recorder which does not have optical digital input or output jack.

OUTPUT

Notes

• Once you have connected a recording component to this unit, keep its power turned on while using this unit. If the power is off, this unit may distort the sound from other components.

• The DIGITAL OUTPUT jack and analog OUT (REC) jacks are independent. The DIGITAL OUTPUT jack only outputs digital signals, while the OUT (REC) jacks output analog signals only.

■ Connecting a turntable

Connect the output jacks on your turntable to the PHONO jacks on this unit. PHONO jacks are for connecting a turntable with an MM or high-output MC cartridge. If you have a turntable with a low-output MC cartridge, use an in-line boosting transformer or MC-head amplifier when connecting to these jacks.

• Connect your turntable to the GND terminal to reduce noise in the signal. Please note that this connection may increase noise with some record players.

Turntable

CD player

CD recorder or

MD recorder

GND

COAXIAL OUTPUT

OPTICAL OUTPUT

OPTICAL INPUT

indicates signal direction

indicates coaxial cables

indicates optical cables

SIGNAL

DIGITAL

INPUT

COAXIAL

OPTICAL

D-TV/CBL

DVD

MD/CD-R

OPTICAL

DIGITAL OUTPUT

GND

VIDEOAUDIOAUDIO

DVD

D-TV

/CBL

VCR-1

OUT

VCR 2 /DVR

OUT

PHONO

(PLAY)

/CD-R

OUT (REC)

MAIN

SURROUND

SUB

WOOFER

6CH INPUT

CENTER

MONITOR OUT

COMPORNENT V

DVD

S VIDEOVIDEO

D-TV

/CBL

MONITOR

OUT

TUNER

AM ANT

GND

75Ω UNBAL.

ANT

S VIDEOVIDEO

Connecting the antennas

CONNECTIONS

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength.

Connect each antenna correctly to the designated terminals.

AM loop antenna

(included)

TUNER

AM ANT

GND

75Ω UNBAL.

FM ANT

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

75-ohm/300-ohm antenna adapter (U.K. model only)

Open the cover of the included 75-ohm/300-ohm antenna adapter.

Indoor FM antenna (included)

11 (7/16)

8 (5/16) 6 (1/14)

Cut the external sleeve of the 75-ohm coaxial cable and prepare it for connection.

Unit: mm (inch)

■ Connecting the AM loop antenna

1 Set up the AM loop antenna, then connect it

to the terminals on this unit.

PREPARATION

2 Press and hold the tab to insert the AM loop

antenna lead wires into the AM ANT and GND terminals.

3 Orient the AM loop antenna for the best

reception.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

Lead wire

Cut the lead wire and remove it.

Clamp with pliers.

Insert the cable wire into the slot, and clamp it with pliers.

Clamp with pliers.

Insert the wire into the slot.

Snap the cover into place.

FREQUENCY STEP switch (China and General models only)

FM/AM

50kHz/9kHz

100kHz/10kHz

FREQUENCY

STEP

Because the inter-station frequency spacing differs in different areas, set the FREQUENCY STEP switch (located on the rear panel) according to the frequency spacing in your area. North, Central and South America: 100 kHz/10 kHz Other areas: 50 kHz/9 kHz Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.

English

CONNECTIONS

Connecting an external amplifier

If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the OUTPUT jacks as follows.

Note

• When RCA pin plugs are connected to the OUTPUT jacks for output to an external amplifier, the SPEAKERS terminals also output signals.

12 3

1 MAIN jacks

Main channel line output jacks.

Note

• The signals output through these jacks are affected by the BASS and TREBLE settings.

2 REAR (SURROUND) jacks

Rear channel line output jacks.

OUTPUT

REAR

(SURROUND

)MAIN

CENTER

SUB

REAR

WOOFER

CENTER

Connecting an external decoder

This unit is equipped with 6 additional input jacks (MAIN left and right, CENTER, SURROUND left and right and SUBWOOFER) for discrete multi-channel input from a component equipped with a multi-channel decoder and 6 channel output jacks such as a DVD/SACD player.

MAIN

SURROUND

SUB

WOOFER

CENTER

6CH INPUT

CENTER

SUBWOOFER MAIN

DVD/SACD player

VCR 2 /DVR

OUT

MONITOR OUT

L R LR

SURROUND

S VIDEOVIDEO

3 CENTER jack

Center channel line output jack.

4 REAR CENTER jack

Rear center channel line output jack.

5 SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or rear channels are directed to this jack in accordance with your SPEAKER SET selections. The unit also directs the LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded to this jack based on your SPEAKER SET selections.

Notes

• The cut-off frequency of the SUBWOOFER jack is 90 Hz.

• If you do not use a subwoofer, allocate the signals to the main left and right speakers by changing the settings of “SOUND 1 SPEAKER SET” item “1E BASS” on the set menu.

• Use the control on the subwoofer to adjust its volume level. You can also adjust the volume level by using this unit’s remote control (see “SETTING THE SPEAKER LEVELS” on page 53).

Note

• When you select 6CH INPUT as the input source, the unit automatically turns off the digital sound field processor, and you cannot use DSP programs.

CONNECTIONS

Connecting the speakers

■ Speakers

This unit has been designed to provide the best soundfield quality with a 6-speaker system, using main left and right speakers, rear left and right speakers, a center speaker, and a rear center speaker. If you use different brands of speakers (with different tonal qualities) in your system, the tone of a moving human voice and other types of sound may not shift smoothly. We recommend that you use speakers from the same manufacturer or speakers with the same tonal quality.

The main speakers are used for the main source sound plus effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are used for effect and surround sounds. The center speaker is for the center sounds (dialog, vocals, etc.). The rear center speaker supplements the rear (left and right) speakers and provides for more realistic front-to-back transitions.

The main speakers should be high-performance models and have enough power-handling capacity to accept the maximum output of your audio system. The other speakers do not have to be equal to the main speakers. For precise sound localization, however, it is ideal to use the models of equivalent performance with the main speakers.

■ Speaker placement

Refer to the following diagram when you place the speakers.

Center speaker

Main speaker (L)

Main speakers

Place the main left and right speakers an equal distance from the ideal listening position. The distance between each speaker and each side of the video monitor should also be the same.

Center speaker

Align the front face of the center speaker with the front face of your video monitor. Place the speaker as close to the monitor as possible (such as directly over or under the monitor) and centrally between the main speakers.

Main speaker (R)

Rear speaker (R)

Subwoofer

1.8 m (6 feet)

Rear center speaker

Rear speaker (L)

PREPARATION

Use of a subwoofer expands your sound field

It is also possible to further expand your system with the addition of a subwoofer. The use of a subwoofer is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the LFE (low-frequency effect) channel with high fidelity when playing back Dolby Digital or DTS signals. The YAMAHA Active Servo Processing Subwoofer System is ideal for natural and lively bass reproduction.

Rear speakers

Place these speakers behind your listening position, facing slightly inwards, about 1.8 m (6 feet) above the floor.

Rear center speaker

Place the rear center speaker in the center between the rear left and right speakers at the same height from the floor as the rear speakers.

Subwoofer

The position of the subwoofer is not so critical, because low bass sounds are not highly directional. However, it is better to place the subwoofer near the main speakers. Turn it slightly toward the center of the room to reduce wall reflections.

Note

• If you do not use any of effect speakers (rear, center and/or rear center), change the settings of “SOUND 1 SPEAKER SET” items at the set menu to direct signals to other terminals you have connected speakers to.

CAUTION

Use magnetically shielded speakers. If these speakers still create interference with the monitor, place the speakers away from the monitor.

English

CONNECTIONS

■ Connections

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) in accordance with the markers on this unit, the speakers, and the speaker cables. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers.

A speaker cord is actually a pair of insulated cables

10 mm (3/8”)

running side by side. One cable is colored or shaped differently, perhaps with a stripe, groove or ridge.

1 Remove approximately 10 mm (3/8”) of

insulation from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

Red: positive (+) Black: negative (–)

3 Unscrew the knob.

4 Insert one bare wire into the hole in the side

of each terminal.

5 Tighten the knob to secure the wire.

Banana plug

(With the exception of U.K. and Europe models)

■ IMPEDANCE SELECTOR switch

WARNING

Do not change setting of the IMPEDANCE SELECTOR switch when the unit power is switched on, as doing so may damage the unit. If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If this is the case, slide the switch all the way to either position when this unit is in standby mode. Be sure to move this switch only when this unit is in standby mode.

(With the exception of U.K. and Europe models)

• You can also use banana plug connectors. First, tighten the knob and then insert the banana plug connector into the end of the corresponding terminal.

Select the switch position (left or right) according to the impedance of the speakers in your system.

(General model)

Switch

Speaker

Impedance level

position

Main

If you use one/two set(s) of main speakers, the impedance of each speaker must be 4 Ω/8 Ω or higher.

Left

Center,

The impedance of each speaker must be 6 Ω or higher.

Rear Center,

Rear

MAIN

A OR B :

A+B :

CENTER

REAR CENTER

REAR

IMPEDANCE SELECTOR

SET BEFORE POWER ON

4ΩMIN.

/SPEAKER

8ΩMIN.

/SPEAKER

6ΩMIN.

/SPEAKER

6ΩMIN.

/SPEAKER

6ΩMIN.

/SPEAKER

MAIN

A OR B :

A+B :

CENTER

REAR CENTER

REAR

8ΩMIN.

16ΩMIN.

8ΩMIN. 8ΩMIN. 8ΩMIN.

/SPEAKER /SPEAKER /SPEAKER /SPEAKER /SPEAKER

Right

Main*

Center,

If you use one/two set(s) of main speakers, the impedance of each speaker must be 8 Ω/16 Ω or higher.

The impedance of each speaker must be 8 Ω or higher.

Rear Center,

Rear

* [Canada model only]

IMPEDANCE SELECTOR switch

When the switch is set to right, you cannot use “A+B”.

CONNECTIONS

SIGNAL

DIGITAL

COAXIAL

OPTICAL

D-TV/CBL

DVD

MD/CD-R

OPTICAL

DIGITAL OUTPUT

INPUT

Main A speaker

Right Left Left

GND

VIDEOAUDIOAUDIO

DVD

D-TV /CBL

VCR-1

OUT

VCR 2 /DVR

OUT

PHONO

(PLAY)

/CD-R

OUT (REC)

MAIN

SURROUND

SUB

WOOFER

6CH INPUT

CENTER

MONITOR OUT

COMPORNENT VIDEO

DVD

S VIDEOVIDEO

D-TV /CBL

MONITOR

OUT

TUNER

ANT

GND

75Ω UNBAL.

ANT

S VIDEOVIDEO

Subwoofer

system

Right Main B speaker

MAIN SPEAKERS terminals

You can connect up to two speaker systems to these terminals. When using only one speaker system, connect it to either of the MAIN A or the MAIN B terminals.

OUTPUT

REAR

(SURROUND

)

MAIN

CENTER

MAIN

R L

Left

CENTER

WOOFER

4231

SUB

SPEAKERS

Rear speaker

Right

R L

REAR

(SURROUND)

CENTER

Center

speaker

REAR

CENTER

Rear center

speaker

MAIN

A OR B :

A+B :

CENTER

REAR CENTER

REAR

IMPEDANCE SELECTOR

SET BEFORE POWER ON

4ΩMIN.

/SPEAKER

8ΩMIN.

/SPEAKER

6ΩMIN.

/SPEAKER

6ΩMIN.

/SPEAKER

6ΩMIN.

/SPEAKER

MAIN

A OR B :

A+B :

16ΩMIN.

CENTER

REAR CENTER

REAR

8ΩMIN.

8ΩMIN. 8ΩMIN. 8ΩMIN.

/SPEAKER /SPEAKER /SPEAKER /SPEAKER /SPEAKER

PREPARATION

REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

REAR CENTER SPEAKER terminals

A rear center speaker can be connected to these terminals.

The diagram shows the speaker layout in the listening room.

SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. This unit will direct low bass signals distributed from the main, center and/or rear channels to this jack in accordance with your SPEAKER SET selections. The LFE (lowfrequency effect) signals generated when Dolby Digital or DTS is decoded are also directed to this jack in accordance with your SPEAKER SET selections.

Notes

• The cut-off frequency of the SUBWOOFER jack is 90 Hz.

• If you do not use a subwoofer, allocate the signals to the main left and right speakers by changing the setting of “SOUND 1 SPEAKER SET” item “1E BASS” on the set menu to MAIN.

• Use the control on the subwoofer to adjust its volume level. You can also adjust the volume level by using this unit’s remote control (see “SETTING THE SPEAKER LEVELS” on page 53).

English

TRANSMIT

RE-NAME

CLEAR

CODE SET

SYSTEM

POWER

STANDBY

6CH INPUT

SLEEP

PHONO

V-AUX

D-TV/CBL VCR 1 VCR2/DVR DVD

TUNER

MD/CD-R

SELECT

POWER

AMP

POWER

CONNECTIONS

Connecting the power supply cords

VOLTAGE SELECTOR

VOLTAGE

SELECTOR

MAIN

A OR B :

4ΩMIN.

A+B :

8ΩMIN.

CENTER

6ΩMIN.

REAR CENTER

6ΩMIN.

REAR

6ΩMIN.

REAR

CENTER

(General model)

■ Connecting the AC power cord

Plug in this unit to a wall outlet.

■ AC OUTLETS (SWITCHED)

U.S.A., Canada, China, Europe, Singapore and

General models ..............................................2 OUTLETS

U.K. and Australia model ................................ 1 OUTLET Use these outlets to connect the power cords from your components to this unit. The power to the AC OUTLETS is controlled by this unit’s STANDBY/ON (or SYSTEM POWER and STANDBY). These outlets will supply power to any source component connected to this unit whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the AC OUTLETS varies depending on the area which it was purchasing.

China and General models......................................... 50 W

Other models ......................................................... 100 W

IMPEDANCE SELECTOR SET BEFORE POWER ON

/SPEAKER

MAIN

A OR B :

/SPEAKER

A+B :

/SPEAKER

CENTER

/SPEAKER

REAR CENTER

/SPEAKER

REAR

AC OUTLETS

SWITCHED

8ΩMIN. 16ΩMIN. :

8ΩMIN. :

8ΩMIN.

/SPEAKER /SPEAKER /SPEAKER /SPEAKER /SPEAKER

Turning on the power

When all connections are complete, turn on the power of this unit.

MAN`L/AUTO FM

VOLUME

BASS

TREBLE

OPTICALRAUDIOLVIDEOS VIDEO

INPUT

STANDBY

/ON

6CH INPUTINPUT MODE

SILENT

PHONES

PROGRAMSTEREOSPEAKERS

EFFECT

PRESET/TUNING

A/B/C/D/E

SET MENU

VIDEO AUX

PRESET/TUNING FM/AM

EDIT

TUNING MODE MEMORY

AUTO/MANUAL MONO

1 Press STANDBY/ON (SYSTEM POWER on

the remote control) to turn on the power of this unit.

SYSTEM

STANDBY

/ON

Front panel

The level of the main volume, and then the current DSP program name appear on the front panel display.

POWER

Remote control

■ VOLTAGE SELECTOR

(China and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/ 220/240 V AC, 50/60 Hz.

P01 CONCERT HALL

≥

INIT.DLY…………45ms

DSP LEVEL…………0dB

ROOM SIZE…………1.0 LIVENESS…………………5

ON-SCREEN DISPLAY (OSD)

You can display operational information for this unit on a video monitor. It is much easier to see the available options and parameters on a monitor than by reading this information on the front panel display.

• If a video source is playing, the OSD is superimposed over the video image.

• The OSD signal is not output to the OUT (REC) jack, and will not be recorded with any video signal.

• You can set the OSD to turn on (gray background) or off when there is no video signal using “OPTION 1 DISPLAY SET” on the set menu.

■ OSD modes

You can select the amount of information shown in the on-screen display.

Full display

This mode shows the DSP program parameter settings continuously on the video monitor.

Short display

This mode briefly shows the front panel display message at the bottom of the screen and then disappears.

Display off

This mode briefly shows “DISPLAY OFF” at the bottom of the screen and then disappears. In this mode, no operational information is shown on the monitor, except when ON SCREEN is pressed.

■ Selecting the OSD mode

SELECT

POWER

AMP

AVTV

REC

DISC SKIP

SET MENU

LEVEL

TITLE

TV VOL

A/B/C/D/E

TV INPUT

TV MUTE

SELECT

–

PRESET PRESET

TEST

ON SCREEN

TV VOL

RETURN

–

AUDIO

DISPLAY

VOL

–

MUTE

CHCH

STEREO

EFFECT

1 Turn on the video monitor connected to this

unit.

2 Press AMP to set the remote control in AMP

mode.

Check that “AMP” is showing in the display on the remote control.

3 Press ON SCREEN on the remote control

repeatedly to change the display mode.

The OSD mode changes in the following order: full display, short display, and display off.

Notes

• The OSD will not display if your video monitor is only connected to the COMPONENT VIDEO jacks of this unit. Be sure to connect your video monitor to the COMPONENT VIDEO jacks and either the VIDEO or the S VIDEO jacks if you want to see the OSD.

• Playing back video software that has an anti-copy signal or video signals with a lot of noise may produce unstable images.

PREPARATION

P01 CONCERT HALL

DSP LEVEL…………0dB

Full display Short display

• When you choose the full display mode, INPUT, VOLUME and other operational information is displayed at the bottom of the screen, in the same format as on the front panel display.

• The set menu and test tone display appear regardless of the OSD mode.

(When using two video monitors)

• If you select video source from a component connected to both the S VIDEO IN and composite VIDEO IN jacks, and both the S VIDEO OUT and the composite VIDEO OUT jacks are connected to two different monitors, the OSD is only displayed on the monitor connected to the S-video jacks. When there is no video signal input from source component, the OSD appears on both monitors.

English

+ 47 hidden pages