Yamaha RX-A2000 Owner Manual

Owner’s Manual

AV Receiver English for Oceania

BEFORE USE

SOURC

AUDIO

V-AUX

USBMU

PHONO

TUNERDOC

[

]

[

]

ECEIVE

ON SCREEN

About this manual

• Some features are not available in certain regions.

• This manual is created prior to production. Design and

LTI

specifications are subject to change in part as a result

of improvements, etc. In case of differences between

the manual and product, the product has priority.

• “

hON SCREEN” (example) indicates the name of

Language selection

This procedure allows you to select the language of menus and messages on the TV screen.

Press hON SCREEN to display the ON SCREEN menu.

Press iCursor B / C to select the favorite language from the following options.

the parts on the remote control. Refer to the “Remote

control” (☞

p. 12) for the information about each

position of the parts.

• J

ENTER

1 indicates that the reference is in the footnote.

Refer to the corresponding numbers on the bottom of

the page.

• ☞

indicates the page describing the related

English (English), (Japanese), (French), (German), (Spanish),

(Russian)

information.

• Click on the “ ” at the bottom of the page to

display the corresponding page in “Part names and

functions.”

Press iCursor B / C to select “Setup” and press iENTER.

Press hON SCREEN to close the ON SCREEN menu.

Front panel

Rear panel

Front panel display

Remote control

Supplied accessories

Check that you received all of the following parts.

• Remote control

• Simplified remote control

• Batteries (AAA, R03, UM-4) x 4

Press iCursor D / E to select the “Language” and press iENTER.

• Power cable

• YPAO microphone

• AM loop antenna

• Indoor FM antenna

En 2

CONTENTS

INTRODUCTION

Features and capabilities...................................................5

Using the TV OSD to operate the unit .............................6

Basic OSD menu operations.............................................6

Viewing or modifying content for the current input source

<Content window> ...........................................................6

Configuring settings for this unit

<ON SCREEN menu>......................................................6

Adjust settings for each input source <Option menu> ..... 7

Part names and functions..................................................8

Front panel........................................................................8

Front panel with the cover opened ...................................9

Rear panel.......................................................................10

Front panel display .........................................................11

Remote control ...............................................................12

Remote control with the cover open...............................13

On-screen display ...........................................................14

CONNECTIONS

Connecting speakers ........................................................15

Speaker channels and functions...................................... 15

Speaker layout ................................................................16

Connecting speakers and subwoofers.............................20

Advanced speaker configuration....................................23

Speaker layout utilizing an external power amplifier..... 23

Connecting an external amplifier ...................................25

Connecting external components....................................26

Jacks and cables..............................................................26

Connecting a TV monitor...............................................27

Connecting BD/DVD players and other devices............ 30

Connecting game consoles or video camcorders............35

Connecting a multi-format player

or an external decoder ....................................................35

Connecting a SCENE link

playback-compatible device ...........................................36

Using the Trigger function to link

external component power..............................................36

Connecting audio/video recording devices .................... 37

Connecting to the network ............................................. 37

Connecting a USB storage device.................................. 38

Connecting the FM/AM antennas .................................. 39

Setting up the speaker parameters automatically

(YPAO).............................................................................. 40

PLAYBACK

Basic playback procedure ............................................... 47

Changing input settings with a single key

(SCENE function) ............................................................ 49

Selecting a SCENE suited to an external component .... 49

Enjoying favorite sound field effect ............................... 50

Selecting sound programs and sound decoders.............. 50

Enjoying surround sound

with the CINEMA DSP function ................................... 50

Enjoying unprocessed playback

(Straight decoding mode) ............................................... 51

Enjoying Hi-Fi Sound Quality (Pure Direct Mode) ....... 52

Enjoying stereo playback ...............................................52

Enjoying compressed music source with better sound

quality (Compressed Music Enhancer) .......................... 52

Sound programs.............................................................. 53

Using the TV display to control this unit....................... 55

Basic operations via the TV screen display ................... 55

Configuring settings specific to an individual input

source (Option menu)...................................................... 57

Option menu display and setup ...................................... 57

Option menu................................................................... 58

Confirming and operating input sources

from the content window................................................. 61

Displaying the content window on the TV screen ......... 61

Switching the display between the Now Playing view

and the Browse view ...................................................... 61

FM/AM tuning................................................................. 62

Selecting a frequency for reception (Normal tuning) .... 62

Navigating the FM/AM tuner

from the content window ............................................... 63

Playing back tunes on the PC......................................... 65

Windows Media Player setup......................................... 65

Playback of PC music contents...................................... 65

Playing back tunes on the USB storage devices............ 67

Playback of the USB storage device.............................. 67

Listening to the Internet Radio ...................................... 69

Listening to Internet Radio ............................................ 69

Using shortcut function................................................... 71

Playing back tunes from your iPod™/iPhone™........... 72

Connecting the Universal Dock for iPod ....................... 72

Controlling an iPod™/iPhone™ .................................... 72

Playing iPod™/iPhone™ from the menu screen

(Menu browse control)................................................... 73

Operating basic playback functions

via the remote control (Simple remote control) ............. 74

Playing iPod™/iPhone™ with wireless connection ...... 74

Playing back tunes from Bluetooth™ components ...... 76

Connecting a Yamaha Bluetooth

Wireless Audio Receiver................................................ 76

Pairing Bluetooth™ components ................................... 76

Using Bluetooth™ components ..................................... 77

Controlling this unit by using the Web browser

(Web Control Center)...................................................... 78

Displaying and Operating Web Control Center ............. 78

En 3

SETUP

Configuring input sources (Input menu) ....................... 80

Configuring input sources .............................................. 80

Input menu......................................................................81

Editing the SCENE function (Scene menu)...................83

Editing a scene................................................................83

Scene menu.....................................................................84

Simple registering as the SCENE...................................85

Setting sound program parameters

(Sound Program menu) ...................................................86

Editing sound programs..................................................86

CINEMA DSP parameters .............................................87

Parameters usable in certain sound programs ................89

Parameters usable in surround decoder .......................... 90

Setting various functions (Setup menu) .........................91

Operating the Setup menu .............................................. 91

Setup menu ..................................................................... 92

Manages settings for speakers........................................92

Setting the audio output function of this unit .................96

Setting this unit’s video output function.........................98

Setting HDMI functions .................................................99

Adjusting this unit’s network parameters..................... 102

Setting this unit’s multi-zone function .........................103

Making the receiver easier to use ................................. 104

Language ......................................................................107

Confirming information of this unit

(Information menu) .......................................................108

Selecting information ................................................... 108

Controlling the remote control

to operate various functions.......................................... 110

Keys connecting external components......................... 110

Customizing the remote control ................................... 111

Setting remote control codes........................................ 111

Programming from other remote controls .................... 113

Changing source names in the display window ...........115

Macro programming features ....................................... 116

Clearing configurations ................................................ 117

Simplified remote control............................................. 119

Extended functionality that can be configured

as needed (Advanced Setup menu)............................... 120

Displaying/Setting the Advanced Setup menu............. 120

Setting the impedance of speakers .............................. 120

Remote sensor .............................................................. 121

Avoiding crossing remote control signals

when using multiple Yamaha receivers........................ 121

Changing TV format .................................................... 122

Removing HDMI video output up-scaling limits......... 122

Recovery and backup of the system settings................ 122

Initializing various settings for this unit....................... 122

Firmware update........................................................... 123

Firmware version.......................................................... 123

Using the HDMI Control function ............................... 124

Enjoying the contents in another room .......................128

Connecting Zone2 or Zone3......................................... 128

Controlling Zone2 or Zone3.........................................130

Enjoying the music in all rooms................................... 130

APPENDIX

Troubleshooting ............................................................. 131

General......................................................................... 131

HDMI™ ....................................................................... 133

Tuner (FM/AM) ........................................................... 134

USB and Network ........................................................ 135

iPod™/iPhone™ .......................................................... 136

Bluetooth™.................................................................. 137

Remote control............................................................. 137

Glossary.......................................................................... 138

Audio information........................................................ 138

Sound program information ......................................... 139

Video information........................................................ 140

Compatibility of the input and output video signals .... 140

Information on HDMI™............................................... 141

About trademarks ......................................................... 142

Specifications.................................................................. 143

Index ............................................................................... 145

En 4

INTRODUCTION

Features and capabilities

■ Built-in high-quality, high-power 7-channel amplifier

■ Multi-channel speaker configuration capability

– 2- to 7.1-channel speaker configurations .................................................................................................16

– Presence speaker connections for playback with a richer sound field effect...........................................15

– Bi-amplification connections for high-quality playback .........................................................................21

– External amplifier connections for high-quality playback and expansion of channels ...........................23

– Speaker impedance configuration ............................................................................................................21

■ HDMI compatibility

– 8 HDMI input jacks (7 on the rear, 1 on the front) supporting 3D video signal input ............................30

– 2 selectable HDMI output jacks supporting Audio Return Channel and 3D video signal ......................28

■ Automatic setup for speaker acoustic parameters

(YPAO - Yamaha Parametric Room Acoustic Optimizer) ......................................40

■ Extensive inputs (max. 13) for external playback components

– BD/DVD/CD player connection..............................................................................................................30

– Game console / video camcorder connection ..........................................................................................35

– Multi-format player / external decoder connection .................................................................................35

– iPod/iPhone wired connection .................................................................................................................72

– iPod/iPhone wireless connection .............................................................................................................74

– Bluetooth component connection ............................................................................................................76

■ 1-button input/sound program/setting switching (SCENE function)................... 49

■ Built-in sound programs and surround decoders for playback variety of sources

– Spatial sound playback with sound field effects (CINEMA DSP) ..........................................................50

– Playback with no sound field effects (straight decoding) ........................................................................51

– High-fidelity sound playback (Pure Direct).............................................................................................52

– Enhanced sound playback for compressed sources (Compressed Music Enhancer)...............................52

■ Playback of music on the USB storage devices ................................................... 67

■ Sophisticated on-screen display (OSD) for easy operation

– Selection of input sources, scenes, and sound programs.........................................................................55

– Navigation for the current input source (content window) ......................................................................61

– Setup for this unit (ON SCREEN menu) .................................................................................................80

– Setup for each input source (Option menu) .............................................................................................57

Most of functions can be operated with on-screen display on the TV screen. Refer to “Using the TV OSD to operate the unit” on the following pages for information on functions that can be controlled using the on-screen display.

■ Customizable remote control

– Remote control code setup for operation of external components ........................................................111

– Learning function from other remote controls.......................................................................................113

– Programming macro for a series of operations ......................................................................................116

■ Multi-room listening capability (Zone2/Zone3) ................................................... 128

■ Tuner playback

– FM/AM broadcast ....................................................................................................................................62

■ Playback and control via network

– Playback of music on the PC and DLNA server......................................................................................65

– Internet radio service playback ................................................................................................................69

– Control this unit via network (Web Browser Control).............................................................................78

En 5

INTRODUCTION

Using the TV OSD to operate the unit

This unit features a sophisticated on-screen display (OSD) for the TV screen. The OSD is designed to enable visual guidance that simplifies operations. The OSD mainly displays the ON SCREEN and Option menus, as well as the content window that displays the content of current input sources.

Basic OSD menu operations

■ Select an input source, scene and sound program

– Select an input source ..............................................................................................................................55

– Select a scene ...........................................................................................................................................55

– Select a sound program ............................................................................................................................56

■ Select a language

– Change the language displayed on the TV screen <Language>............................................................107

Viewing or modifying content for the current input source <Content window>

■ Operate the FM/AM tuner

– Display preset stations for selection ........................................................................................................63

– Display information on the station currently received.............................................................................63

– Perform operations such as searching for and registering stations using the screen button ....................63

■ Operate the Internet radio

– Display information on the station currently received.............................................................................69

– Play back radio contents ..........................................................................................................................69

– Bookmark Internet radio stations.............................................................................................................69

■ Operate the iPod music sources

– Display the list of iPod music sources for selection ................................................................................73

– Perform operations such as play, stop and pause using the TV screen <Menu browse control> ............73

Configuring settings for this unit <ON SCREEN menu>

■ Configure an input source

– Change the input source name <Rename/Icon Select> ...........................................................................81

– Specify a format for digital audio signals <Decoder Mode> .................................................................. 82

– Enhance the sound of compressed audio <Enhancer> ............................................................................82

– Output a video signal input from another input source

while playing a multi-channel audio signal <Video Out>.......................................................................82

– Charge the iPod/iPhone when this unit is in standby mode <Standby Charge>......................................82

– Play music sources on a PC using external controls <DMC Control> ....................................................82

■ Customize a scene

– Register or clear settings for a selected scene <Save>, <Load>, <Reset> ........................................84, 85

– Turn on a Yamaha BD/DVD player or CD player connected to this unit automatically

when a scene is selected <SCENE IR> ...................................................................................................84

– Changing a scene name and icon <Rename/Icon Select> .......................................................................85

■ Adjust a sound program (sound program)

– Adjust sound program parameters ...........................................................................................................86

■ Display settings information for this unit

– Display audio signal information <Audio Signal> ................................................................................ 108

– Display video signal information <Video Signal> ................................................................................108

– Display HDMI signal information <HDMI Monitor>........................................................................... 108

– Display network information <Network>..............................................................................................109

– Display system information <System>..................................................................................................109

– Display Zone information <Zone> ........................................................................................................109

Continues to the

En 6

INTRODUCTION

Using the TV OSD to operate the unit

■ Adjust acoustic parameters to match your speakers and listening environment

– Specify speaker acoustic parameters automatically

(Yamaha Parametric Room Acoustic Optimizer - YPAO).......................................................................40

– Set up this unit’s speaker configuration simply <Power Amp Assign> ..................................................93

– Specify settings for each speaker <Configuration>.................................................................................93

– Control volume control for each speaker <Level> ..................................................................................95

– Apply speaker distance settings <Distance> ...........................................................................................95

– Control equalizer sound quality <Parametric EQ> ..................................................................................95

– Adjust test tone speaker <Test Tone>......................................................................................................96

■ Adjust audio signals output from this unit

– Correct lag between audio and video signals <Lipsync> ........................................................................96

– Select a dynamic range adjustment method <Dynamic Range> .............................................................97

– Specify the maximum volume <Max Volume>.......................................................................................97

– Specify the initial volume <Initial Volume>............................................................................................97

– Restrict video signal in Pure Direct Mode <Pure Direct Mode>.............................................................97

– Adjust DSP effect and volume level <Adaptive DSP Level>..................................................................97

■ Adjust video signals output from this unit

– Convert analog video signal to another type of signal <Analog to Analog Conversion> .......................98

– Specify the resolution and aspect ratio of video signals and adjust video quality <Processing>............98

■ HDMI settings

– Assign the audio input source for the TV <TV Audio Input> ...............................................................100

– Listen to TV audio with HDMI cable connection <ARC (Audio Return Channel)>............................100

– Transmit HDMI audio/video to the TV during standby mode <Standby Through> .............................101

– Change the output destination of HDMI input audio signals <Audio Output>.....................................101

■ Specify other functions for this unit

– Enter standby mode automatically when no operations are performed <Auto Power Down> .............105

– Assign jacks to the selected input source <Input Assignment> ............................................................105

– Adjust the brightness of the front panel display <Dimmer> .................................................................106

– Change the wall paper displayed on the TV screen <Wall Paper>........................................................106

– Specify the function of the TRIGGER OUT jack for controlling external components

<Trigger Output1/Trigger Output2> ......................................................................................................106

– Prohibit changes to settings <Memory Guard> .....................................................................................107

Adjust settings for each input source <Option menu>

– Adjust bass and treble levels <Tone Control> .........................................................................................59

– Enable low-volume background music <Adaptive DRC> ......................................................................59

– Enjoying more spatial sound fields <CINEMA DSP 3D Mode>............................................................59

– Adjust the vertical position of dialogues <Dialogue Lift>......................................................................59

– Select the 5.1-channel signal playback method <Extended Surround> ..................................................59

– Adjust the volume of input sources <Volume Trim>...............................................................................60

– Selecting a video adjustment preset <Video Adjustment>......................................................................60

– Selecting audio input jacks <Audio Select>............................................................................................60

– Shuffle or repeat playback <Shuffle/Repeat>..........................................................................................60

– Connect / Disconnect Bluetooth component to this unit <Connect/Disconnect> ...................................60

– Pairing Bluetooth component with this unit <Pairing> ........................................................................... 60

■ Network settings

– Specify this unit’s IP address <IP Address> ..........................................................................................102

– Accept the commands over a LAN network when this unit is in the standby mode

<Network Standby> ...............................................................................................................................102

– Specify the mac address filter for this unit <MAC Address Filter> ...................................................... 102

■ Enable listening in multiple rooms (multi-zone function)

– Adjust Zone2/Zone3 volume <Zone2 Set/Zone3 Set> ..........................................................................103

– Display the Zone2/Zone3 menu on the TV <Monitor Out Assign> ......................................................103

– Rename zones or scenes <Zone2 Scene Rename/Zone3 Scene Rename/Zone Rename>.....................104

En 7

Part names and functions

INTRODUCTION

Front panel

a MAIN ZONE A (Power)

Switches this unit between on and standby mode.

b HDMI Through/iPod Charge indicator

Lights up in any of the following cases while the unit is in standby mode.

• When the Standby Through function is enabled and audio/video from an external component connected with HDMI is output to a TV during standby mode (☞

• When an iPod/iPhone, which is placed in the Universal Dock for iPod, is charging while the unit is in standby mode (☞ This indicator also lights up when the Yamaha Wireless System for iPod is connected to this unit (☞

p. 101).

p. 82).

p. 74).

c Front panel display

Displays information on this unit (☞

d PURE DIRECT

Switches this unit to Pure Direct Mode (☞

e INPUT selector

Selects an input source from which to playback. Rotate this selector to cycle through the input sources in order.

f VOLU ME

Adjusts the volume level.

p. 11).

p. 52).

c db

■ Opening and closing the front panel door

To use controls or jacks behind the front panel door, gently press the bottom of the door to open it. Keep the door closed when not using controls or jacks behind the front panel door.

e f

Continues to the

En 8

Front panel with the cover opened

g ON SCREEN

Turns on and off the ON SCREEN menu.

h OPTION

Turns on and off the Option menu (☞

i TONE/BALANCE

Adjusts high-frequency/low-frequency output of speakers/headphones in each zone (☞ Adjusts the balance of the volume of the left and right channels in

Zone2 or Zone3 (☞

p. 48, p. 130).

p. 130).

j STRAIGHT

Changes a sound program to straight decoding mode (☞

k PROGRAM l / h

Selects a sound program (☞ to cycle through sound programs.

p. 50). Press the left or right key repeatedly

l SCENE

Switches the input source, the sound program, and the HDMI OUT with a single button (☞ press this key to switch on.

p. 49, p. 83). When this unit is in standby mode,

p. 57).

p. 51).

m MULTI ZONE

ZONE2

Switches to enable/disable the audio and video output to Zone2

p. 103, p. 128).

(☞

ZONE3

Switches to enable/disable the audio and video output to Zone3

p. 103, p. 129).

(☞

ZONE CONTROLS

Switches to Zone2 or Zone3 operation mode. This unit, or its remote control, can be used to select input sources or adjust volume for an external amplifier in another room or the built-in amplifier for speakers in another room (☞

p. 130).

n INFO

Changes the information displayed on the front panel display (☞

o MEMORY

Registers FM/AM stations as preset stations (☞

p. 62). J1

p FM/AM

Sets the FM/AM tuner band to FM or AM (☞

p. 62). J1

q PRESET j / i

Selects an FM/AM preset station (☞

p. 63). J1

p. 11).

INTRODUCTION

Part names and functions

r Cursor B / C / D / E, ENTER, RETURN

Cursor B / C / D / E Select menu items and change settings when

ENTER Confirms a selected item. RETURN Returns to the previous screen when menus are

s USB port

For connecting a USB memory device or portable USB audio player (☞

t DISPLAY

Switches the display between the Now Playing view and the Browse view.

u YPAO MIC jack

Connect the supplied YPAO microphone and adjust the speaker balance automatically (☞

v PHONES jack

For plugging headphones in. Sound effects applied during playback can also be heard through the headphones.

w VIDEO AUX jacks

For connecting game consoles to this unit temporarily (☞

x TUNING/CH jj / ii

Changes FM/AM tuner frequencies (☞

menus, etc., are displayed.

displayed, or close the menu.

p. 40).

p. 35).

p. 62). J1

p. 38).

1 : Usable when you have selected TUNER input.

vus

mg li o qnjh p

xt w

En 9

Rear panel

SURROUNDSURROU

AV 1AV 2

AV 3

AV 5

AV 6

AV 7

SING

FRO

AV 3

CAL

(2 TV) (3 CD)

CENTER

PBPRY

PBP

OUT

+12V 0.1A MA

)

AV 2

a PHONO jacks

For connecting a turntable (☞

b DOCK jack

For connecting an optional Universal Dock for iPod (such as YDS-

12), Wireless System for iPod (YID-W10), or Bluetooth Wireless

Audio Receiver (YBA-10) (☞

c NETWORK port

For connecting to a network (☞

d HDMI OUT 1-2 jacks

For connecting an HDMI - compatible TV to output audio/video signals (☞

p. 28).

e MON.OUT/ZONE OUT jacks (S-VIDEO/VIDEO jacks)

For connecting a TV capable of receiving video input, and outputting video signals to it (☞

f COMPONENT VIDEO jacks

For connecting external components that support component video output for video signal reception (☞

p. 34).

p. 72, p. 74, p. 76).

p. 37).

p. 28, p. 29).

p. 31).

g HDMI input jacks

For connecting external components equipped with HDMIcompatible outputs to receive audio/video signals (☞

p. 30).

h MONITOR OUT/ZONE OUT jacks (COMPONENT VIDEO

jacks)

For connecting TV that are compatible with component video signals, using three cables to output video signal (☞

p. 28).

i REMOTE IN/OUT1-2 jacks

For connecting an external component that supports the remote control function (☞

p. 36).

j TRIGGER OUT 1-2 jack

For connecting an external component that supports the trigger function to operate it linked with operation of this unit (☞

p. 36).

k RS-232C terminal

This is a control expansion terminal for custom installation. Consult your dealer for details.

l AV1-4 jacks

For connecting to external components equipped with audio/video outputs to receive audio/video signals (☞

p. 31).

m ANTENNA jacks

For connecting AM and FM antennas (☞

p. 39).

INTRODUCTION

Part names and functions

n AV OUT jacks

For outputting audio/video signals received when analog inputs are selected (☞

o AUDIO1-4 jacks

For connecting external components equipped with audio outputs to receive audio signals (☞

p MULTI CH INPUT jacks

For connecting a player that supports a multi-channel output (☞

q ZONE OUT jacks

Outputs sound of this unit to an external amplifier set in a different room. (☞

r PRE OUT terminals

For connecting a subwoofer with built-in amplifier or an external power amplifier (☞

s SPEAKERS terminals

For connecting the front, center, surround and surround back speakers (☞ Zone2 and Zone3 (☞

t AC IN

For connecting the supplied power cable.

p. 37).

p. 34).

p. 35).

p. 128).

p. 22, p. 25).

p. 20). Connect the presence speakers (☞p. 20) or the speakers for

p. 21) to the EXTRA SP jacks.

bad g kjf

e h i

Distinguishing the input and output jacks

DOCK NETWORK

AV 1

AV 2 AV 3 AV 4

(1 BD/DVD)

PHONO

GND

COAXIAL COAXIAL

abcd ef

ANTENNA

(4 RADIO)

OPTICAL OPTICAL

GND

AV OUT

HDMI OUT

ARC ARC

SELECTABLE

MON.OUT/ZONE OUT

AUDIO 1

AUDIO 2 AUDIO 3 AUDIO 4

(2 TV)

(3 CD)

OPTICAL

COAXIAL

EXTRA SP2

AV 1

(1 BD/DVD)

COMPONENT VIDEO

YPBPRYPBP

AV 1

AV 2

ZONE2/ZONE3

FRONT

MULTI CH INPUT

SURROUND

SUR. BACK

ZONE OUT PRE OUT

CENTER

ZONE 2

SUBWOOFER

HDMI

MONITOR OUT/ZONE OUT

YPBP

ZONE 3

SPEAKERS

AV 2 AV 3 AV 4

AV 3

AV 4

SURROUND SURROUND BACK/

AV 5 AV 6 AV 7

FRONT/

SURROUND

F. PRESENCE

BI-AMP

SINGLE

REMOTE

OUT IN OUT

(FRONT)

(SINGLE)

(REAR)

CENTER

SUR. BACK

SUBWOOFER

CENTER

FRONT

TRIGGER

OUT

+12V 0.1A MAX.

EXTRA SP1

RS-232C

ZONE2/ZONE3/

F.PRESENCE

AC IN

The area around the audio/video output jacks is marked

in white to prevent connection errors. Use these jacks to

output audio/video signals to a TV or other external

component.

V 4

UBWOOFER

HDMI

YPBP

ZONE OUT PRE OUT

ZONE 2

ZONE 3

PEAKER

TRIGGER

EMOT

(FRONT)

(SINGLE)

CENTER

SURROUND

SUR. BACK

ND BACK

ENTE

HDMI OUT

ARC ARC

SELECTABLE

AV OUT

MON.OUT/ZONE OUT

UDIO 1

UDIO

PTICA

COAXIA

(1 BD/DVD

COMPONENT VIDEO

UDIO

UDIO 4

LTI CH INPUT

FRONTSURROUNDSUR. BAC

NE2/ZONE

EXTRA SP

Output jacks

o p q r

sl nmt

En 10

Front panel display

a Tuner indicator

Light up according to the status of a received station (☞

b ZONE2/ZONE3 indicator

Lights up when the audio or video output to Zone2 or Zone3 is enabled (☞

p. 130).

c SLEEP indicator

Blinks when the sleep timer is on (☞

p. 13, p. 130).

d PARTY indicator

Lights up when the party mode is active (☞

p. 103).

e Multi information display

Displays a range of information on menu items and settings.

f VOLUME indicator

Displays the current volume level.

g HDMI indicator

Lights up during normal HDMI communication.

IN indicator

Lights up when this unit detects the external component connected to the HDMI input jack (☞

OUT 1/OUT 2 indicators

Indicate which HDMI OUT jack outputs audio/video signals (☞

p. 28).

p. 30).

h ENHANCER indicator

Lights up when the Compressed Music Enhancer is active (☞

p. 62).

p. 52).

i CINEMA DSP indicator

Lights up when a sound field effect that uses CINEMA DSP technology is selected.

j CINEMA DSP 3D indicator

Lights up when CINEMA DSP 3D is activated (☞

p. 51).

k Cursor indicators

Light up if corresponding cursors on the remote control are available for operations.

l MUTE indicator

Blinks when audio is muted.

m Speaker indicators

Indicate speaker terminals from which signals are output.

Center speaker

Subwoofer 1

Front L speaker Front R speaker

Presence L speaker Presence R speaker

Surround L speaker

Surround back L

speaker

Surround back

speaker J1

Subwoofer 2

Surround R speaker

Surround back R speaker

INTRODUCTION

Part names and functions

n ADAPTIVE DRC indicator

Lights when the adaptive dynamic range control feature is tuned on (☞

p. 59).

■ Switching information on the front panel display

The front panel can display sound programs and surround decoder names as well as the active input source. Press tINFO repeatedly to cycle through displayed informations. J2

Input source name



AV1

VOLUME

Standard

Sound program (DSP program)

be fa c

STEREO

ENHANCER

TUNED

SLEEP

PA RT Y

ihj mknlgk

1 : “SB” is displayed when using a 6.1-channel configuration only.

2 : During FM/AM reception, the frequency is displayed instead of the input source.

MUTE

ADAPTIVE

VOLUME

DRC

En 11

Remote control

SOURCE

RECEIVER

USB

[ A ]

VOLUME

POP-UP/MENU

LIVE

CLUB

STEREO

V-AUX

NET

[ B ]

OPTION

ENTERTAIN

STRAIGHT

PURE

DIRECT

AUDIO

MULTI

PHONO

TUNER

DOCK

SCENE

MUTE

PROGRAM

TOP MENU

ON SCREEN

ENTER

RETURN DISPLAY

REC

CLASSICAL

PRESET

MOVIE

INPUT

TV VOL TV CH

MUTE

INTRODUCTION

Part names and functions

a Remote control signal transmitter

Transmits infrared signals.

b SOURCE A (SOURCE Power)

Switches an external component on and off.

c Display window

Displays remote control information.

l m

d Input selector

Select an input source on this unit from which to playback.

AV1 -7 AV1-7 jacks V-AUX Front panel VIDEO AUX jacks

AUDIO1-4 AUDIO1-4 jacks PHONO PHONO jacks MULTI MULTI CH INPUT jacks

USB A USB storage device connected to the USB port. NET Internet radio, a USB connected to the USB port,

or a PC connected to the NETWORK port.

DOCK A Universal Dock for iPod, Wireless System for

iPod, or Bluetooth Wireless Audio Receiver

connected to the DOCK jack.

TUNER FM/AM tuner [A]/[B] Changes the external component to operate with

e SCENE

Switch the input source and the sound program with a single button (☞

p. 49). When this unit is in standby mode, press this key to switch

on.

the gExternal component operation keys without changing inputs. J1

f PROGRAM k / n

Selects a sound program (☞ repeatedly to cycle through sound programs.

g External component operation keys

Operate recording, playback, and menu displays etc. for external components (☞

p. 110). J1

p. 50). Press the up or down key

h ON SCREEN

Turns on and off the ON SCREEN menu.

i Cursor B / C / D / E, ENTER, RETURN

Cursor B / C / D / E Select menu items and change settings when

menus, etc., are displayed.

ENTER Confirms a selected item. RETURN Returns to the previous screen when menus are

displayed, or close the menu.

j PRESET F / G

Selects a preset station when the FM/AM tuner is operated.

k TV control keys

Operate a monitor such as a TV.

l RECEIVER A (RECEIVER Power)

Switches this unit between on and standby mode.

m SOURCE/RECEIVER

Switches remote control key function to operate this unit or an external component (☞

p. 110). Operate an external component when

this key glows green, or this unit when this key glows orange.

n VOLUME +/-

Adjust the volume level (☞

p. 47).

o MUTE

Turns the mute function of the sound output on and off (☞

p OPTION

Turns on and off the Option menu (☞

p. 57).

q DISPLAY

Switches the display between the Now Playing view and the Browse view.

r Sound selection keys

Switch between the current sound field effect (sound program) and the surround decoder (☞

p. 50).

p. 47).

1 : You can use gExternal component operation keys for each input source to operate registered components. Remote control codes must be registered for each input

in advance if you want to operate external components (☞

p. 112).

En 12

Remote control with the cover open

SOURCE

RECEIVER

AUDIO

MULTI

PHONO

TUNER

DOCK

SCENE

MUTE

PROGRAM

TOP MENU

ON SCREEN

ENTER

RETURN DISPLAY

SUR.

ENHANCER

DECODE

INFO

MEMORY

USB

[ A ]

VOLUME

POP-UP/MENU

PARTY

ENT

ZONE

V-AUX

NET

[ B ]

OPTION

HDMI OUT

TUN./CH

SLEEP

LEVEL

SETUP

v w

A B

s Sound selection keys

Switch between the current sound field effect (sound program) and the surround decoder (☞

p. 50).

t INFO

Cycles the information displayed on the front panel display (the name of the currently selected input source, the sound program, the surround decoder, the FM/AM tuner frequency, etc.).

u Numeric keys

Enter numbers.

v PART Y

Switches the party mode on and off (☞

p. 130).

w HDMI OUT

Switches the output jack connected to an HDMI compatible TV (☞

p. 47).

x Radio control keys

Operates the FM/AM tuner. These keys are used when using the tuner input.

MEMORY Presets radio stations. FM Sets the FM/AM tuner band to FM. AM Sets the FM/AM tuner band to AM. TUN./CH H / I Changes tuning frequencies.

y SLEEP

Switches this unit to standby mode automatically after a specified period of time has elapsed (sleep timer). Press this key repeatedly to set the time for the sleep timer function.

120min. 90min.

60min.30min.Off

The SLEEP indicator lights up when the sleep timer is on.

z LEVEL

Adjusts the output level for each speaker (☞

p. 95).

A SETUP

Setup this remote control (☞

p. 111).

B ZONE

Switches the zone to be operated by the remote control between the Main zone, Zone2, and Zone3 (☞

p. 130).

INTRODUCTION

Part names and functions

■ Installing batteries in the remote control

When inserting batteries in the remote control, remove the battery compartment cover from the reverse side of the remote control, and insert four AAA batteries into the battery compartment so that they match with the polarity markings (+ and -).

Battery compartment cover

Replace the batteries with new ones if the remote control can only be operated within a narrow range.

NOTE

If there are remote control codes for external components registered to the remote control, removing the batteries for more than 2 minutes, or leaving exhausted batteries in the remote control, may clear the remote control codes. If this should occur, replace the batteries with new ones, and set the remote control codes.

Battery compartment

En 13

On-screen display

When a TV is connected to this unit, the supplied remote control can be used to specify and verify this unit’s settings via menus and options displayed on the TV screen.

The following displays are available in the on-screen display.

ON SCREEN menu

Press hON SCREEN to display the ON SCREEN menu.

INTRODUCTION

Part names and functions

Content window

Press dInput selector to display the content window.

Option menu

Detailed settings for this unit can be configured. Use this menu to select desired settings, change their values, or check the current status of this unit. Refer to “SETUP” (☞

Press pOPTION to display the Option menu.

Configure the optional settings for each input source. Settings such as “Tone Control” and “Volume Trim” are applied to this unit regardless of the input source. Refer to “Configuring settings specific to an individual input source (Option menu)” (☞

p. 57) for details.

p. 80) for details.

Includes the Browse view and the Now Playing view. The Now Playing view displays the status of the source from which music is currently played back. Adjust settings for music content from the Browse view. Refer to “Confirming and operating input sources from the content window” (☞ for details.

p. 61)

En 14

CONNECTIONS

Connecting speakers

This unit uses acoustic field effects and sound decoders to bring you the impact of a real movie theater or concert hall. These effects will be brought to you with ideal speaker positioning and connections in your listening environment.

■

Speaker channels and functions

■

Front left and right speakers

The front speakers are used for the front channel sounds (stereo sound) and effect sounds.

Surround left and right speakers

The surround speakers are for effect and vocal sounds while playing back more than 5.1-channel source. When used with no surround back speaker while playing back more than 6.1-channel source (including surround back channel), sound of surround back channel is distributed between the left and right surround speakers.

■

Surround back left and right speakers

The surround back speakers are for rear effect sounds while playing back more than 6.1-channel source. When used with only one surround back speaker while playing back more than 7.1channel source, sound of the left and right surround back channel is mixed and output from a single speaker.

E.g.

Front speaker layout: Place these speakers at an equal distance from the ideal listening position in the front of the room. When using a projector screen, the appropriate top positions of the speakers are about 1/4 of the screen from the bottom.

■

Center speaker

The center speaker is for the center channel sounds (dialogue, vocals, etc.).

E.g.

Center speaker layout: Place it halfway between the left and right front speakers. When using a TV, place the speaker just above or just under the center of the TV with the front surfaces of the TV and the speaker aligned. When using a screen, place it just under the center of the screen.

E.g.

Surround speaker layout: Place the speakers at the rear of the room on the left and right sides facing the listening position. They should be placed between 60 degrees and 80 degrees from the listening position and with the speaker tops at a height of 1.5 – 1.8 m from the floor.

■

Presence left and right speakers

The presence speakers are used for front effect sounds. When used in combination with the sound programs (☞ richer and more spatial presence is possible.

Presence speaker layout: Place the left and right presence speakers 0.5 – 1 m to the outside of the left and right front speakers respectively. The tops of the presence speakers should be 1.8 m above the floor.

p. 53), a sound with a

E.g.

Surround back speaker layout: When used with 7.1ch sound, arrange the left and right speakers towards the listening position, to the rear of the listening position. Arrange the left and right speakers at least 30 cm apart. The same separation as with the front left and right speakers is optimum. When used with 6.1ch sound, arrange these to the rear of the listening position.

■

Subwoofer

The subwoofer speaker is used for bass sounds and low-frequency effect (LFE) sounds included in Dolby Digital and DTS. Use a subwoofer that is equipped with built-in amplifier.

E.g.

Subwoofer speaker layout: Place it to the outside of the front left and right speakers facing slightly inward to reduce echoes from the wall. You can use one or two subwoofers and select the position of subwoofers from “Left + Right,” “Front + Rear” and “Monaural x2” (☞p. 94).

En 15

Speaker layout

In addition to the 7.1-channel speaker layout, a variety of speaker configurations can be specified with presence speaker connection, bi-amp connection or the Zone2/Zone3 function. In addition, this unit is equipped with the “Power Amp Assign” function, which can be used to easily apply the appropriate speaker settings to this unit according to speaker configuration.

■

Connection of speakers

Connect the speakers to the appropriate jacks shown in the table for each speaker layout. Refer to “Connecting speakers and subwoofers” (☞ You can also use two subwoofers by connecting them to both SUBWOOFER1 (FRONT) and SUBWOOFER2 (REAR) jacks. And, you can use the EXTRA SP1 jacks for Zone3 speakers and EXTRA SP2 jacks for Zone2 by setting the assignment with “Power Amp Assign” (☞

■

Assigning a speaker configuration

A speaker configuration must be assigned to this unit to activate the speakers. Use the Power Amp Assign function to apply the appropriate settings shown in the table for each speaker layout. Refer to “Power Amp Assign” (☞

p. 93) for details on setting.

p. 20) for details on connecting speakers.

p. 93).

CONNECTIONS

Connecting speakers

■

Enjoying the 7.1 channel audio source

■ 7.1-channel speaker layout (7 speakers + subwoofer)

Front R speaker

Front L speaker

Center speaker

Surround L speaker

Surround back L speaker J1

Audio from a 7.1-channel audio source can be played back with no degradation with this speaker configuration.

Subwoofer

Surround R speaker

30 cm or more

Surround back R speaker

1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back

speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.

■ Connections of speakers

FRONT jacks Front L/R speakers SURROUND

BACK jacks

CENTER jack Center speaker SUBWOOFER

(PRE OUT) jack

SURROUND jacks Surround L/R speakers

■ Assigning a speaker configuration

Power Amp Assign 7ch Normal (Default)

Surround back L/R speakers

Subwoofer

En 16

■

Adding the presence speakers for a richer sound field effect

■ Presence speaker layout (7 speakers + subwoofer + presence speakers)

Presence L speaker

Front R speaker

Front L speaker

Presence R speaker

Subwoofer

Surround R speaker

CONNECTIONS

Connecting speakers

■

Enjoying the audio source without surround back speakers

■ 5.1-channel speaker layout (5 speakers + subwoofer)

Front R speaker

Front L speaker

Subwoofer

Surround R speaker

Center speaker

Surround back

Surround L speaker

Surround back L speaker J1

30 cm or more

R speaker

This unit automatically selects the presence speakers or surround back speakers to output sounds according to the selected sound program. When the sound program is changed, the speakers that output the sound are switched between the presence speakers and surround back speakers automatically. J2

■ Connections of speakers

FRONT jacks Front L/R speakers SURROUND

BACK jacks

CENTER jack Center speaker SUBWOOFER

(PRE OUT) jack

SURROUND jacks Surround L/R speakers EXTRA SP1 jacks Presence L/R speakers

Surround back L/R speakers

Subwoofer

■ Assigning a speaker configuration

Power Amp Assign 7ch Normal (Default)

1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back

speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.

2 : Sound cannot be output from the surround back speakers when it is output from the speakers connected to the EXTRA SP1

jacks.

Center speaker

Surround L speaker

This unit can mix 7.1-channel audio source down to 5.1-channel sound. This enables 7.1-channel sound without surround back speakers.

■ Connections of speakers

FRONT jacks Front L/R speakers SURROUND jacks Surround L/R speakers

CENTER jack Center speaker SUBWOOFER

(PRE OUT) jack

Subwoofer

■ Assigning a speaker configuration

Power Amp Assign 7ch Normal (Default)

En 17

■

Using the front speakers that support bi-amp connections for a high quality sound

■ 5.1-channel speaker layout (Front speakers (Bi-amp) + 3 speakers)

Front R speaker (Bi-amp connection)

Front L speaker (Bi-amp connection)

Subwoofer

Surround R speaker

CONNECTIONS

Connecting speakers

■

Using speakers in two rooms (Zone2 function)

■ 7.1-channel speaker layout + Zone2 (7 speakers (in main zone) + subwoofer (in main zone) + front speakers (in secondary zone))

Main zone Zone2

Front L speaker

Front R speaker

Subwoofer

Surround R speaker

Front R speaker

Center speaker

Surround L speaker

Using the front speakers that support bi-amp connections reproduces a high quality sound.

■ Connections of speakers

FRONT jacks Front L/R speakers (bi-amp) SURROUND

BACK jacks

CENTER jack Center speaker SUBWOOFER

(PRE OUT) jack

SURROUND jacks Surround L/R speakers

Front L/R speakers (bi-amp)

Subwoofer

■ Assigning a speaker configuration

Power Amp Assign 5ch BI-AMP

1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back

speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.

2 : Sound cannot be output from the surround back speakers when it is output from the speakers connected to the EXTRA SP1

jacks.

3 : EXTRA SP1 jacks can also be assigned to the Zone3 speakers with “Power Amp Assign” (☞p. 93).

Center speaker

Surround L speaker

Surround back L speaker J1

30 cm or more

Surround back R speaker

Front L speaker

In addition to the main room, speakers in another room can also be controlled. When the built-in amplifier assigned to speakers in another room is turned on, sound output automatically switches from the surround back speakers to the speakers in the other room. J2

■ Connections of speakers

FRONT jacks Front L/R speakers SURROUND

BACK jacks

CENTER jack Center speaker SUBWOOFER

(PRE OUT) jack

SURROUND jacks Surround L/R speakers EXTRA SP1

jacks J3

Surround back L/R speakers

Subwoofer

Zone2 speakers

■ Assigning a speaker configuration

Power Amp Assign 7ch + 1ZONE

En 18

CONNECTIONS

Connecting speakers

■

Using speakers in three rooms (Zone2 and Zone3 functions)

■ 7.1-channel speaker layout + Zone2 + Zone3 (7 speakers (in main zone) + subwoofer (in main zone) + front speakers (in secondary and tertiary zones))

Main zone

Front L speaker

Center speaker

Surround L speaker

Surround back L speaker J1

Front R speaker

Subwoofer

30 cm or more

Zone2

Surround R speaker

Front L speaker

Zone3

Surround back R speaker

Front L speaker

Front R speaker

In addition to the main room, speakers in other two rooms can also be controlled. When the built-in amplifier assigned to speakers in another room is turned on, sound output automatically switches from the surround back and/or surround speakers to the speakers in the other rooms. J2, J3

■ Connections of speakers

FRONT jacks Front L/R speakers SUBWOOFER

(PRE OUT) jack

CENTER jack Center speaker EXTRA SP1

jacks J4

SURROUND jacks Surround L/R speakers EXTRA SP2

jacks J5

SURROUND

BACK jacks

Surround back L/R speakers

■ Assigning a speaker configuration

Power Amp Assign 7ch + 2ZONE

Subwoofer

Zone2 speakers

Zone3 speakers

1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back

speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.

2 : Sound cannot be output from the surround back speakers when it is output from the speakers connected to the EXTRA SP1

jacks.

3 : Sound cannot be output from the surround speakers when it is output from the speakers connected to the EXTRA SP2 jacks.

4 : EXTRA SP1 jacks can also be assigned to the Zone3 speakers with “Power Amp Assign” (☞p. 93).

5 : EXTRA SP2 jacks can also be assigned to the Zone2 speakers with “Power Amp Assign” (☞p. 93).

En 19

CONNECTIONS

AV 6

AV 7

OMPO

OUT

PRY

PBP

(

)

SUBWOOFER

()()

OUT

(SINGLE)

)

AV 6

(

)

(FRONT)

SUBWOOFER

()()

OUT

+12V 0.1A MAX.

SINGLE)

Connecting speakers

Connecting speakers and subwoofers

Connect your speakers to their respective terminals on the rear panel.

CAUTION

• Remove the power cable of this unit from the power outlet before connecting the speakers.

• Generally speaker cables consist of two parallel insulated cables. One of these cables is a different color, or has a line running along it, to indicate different polarity. Insert the different colored (or lined) cable into the “+”

(positive, red) terminal on this unit and the speakers, and the other cable into the “–” (negative, black) terminal.

• Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, “CHECK SP

WIRES!” will appear on the front panel display when this unit is switched on.

■ Front/Center/Surround/Surround back speaker and Subwoofer connection

When connecting only one surround back speaker, connect the speaker to the SURROUND BACK L (SINGLE) jacks.

(FRONT)

EMOTE

REAR

CENTE

Front speaker

RS-232

TRIGGE

12V 0.1A MAX

FRONT

XTRA SP1

NE2/Z

F.PRESE

V 2AV

DVD

NENT VIDE

ULTI CH INPU

ENTER

RROUNDSUR. BACKSUBWOOFE

SURROUND SURROUND BACK/

Subwoofer

V 4AV

MONITOR OUT/ZONE OUT

ZONE

RONT

NE 2

F. PRESENCE

BI-AMP

PRE

SINGLE

URROUN

UR. BACK

CENTER

■ Presence speaker connection

When using the presence speakers, connect the speakers to the EXTRA SP1 jacks as shown in the diagram below.

Presence speaker

RS-232C

TRIGGE

NOUT

RON

EXTRA SP1

ZONE2/ZONE3/

F.PRESENCE

AC IN

EMOTE

REAR

ENTE

R. BA

ENTE

The presence speakers (PL/PR) that output front effect sounds can be connected to this unit. With the sound programs (☞

p. 57),

sound with a richer and more spatial presence can be created.

0.5 – 1 m 0.5 – 1 m

PL PR

1.8 m 1.8 m

Connection of presence speakers is recommended to take full advantage of the effects of CINEMA DSP sound programs.

Continues to the

RL RL

Surround

speaker

Surround back

speaker

Center speaker

En 20

CONNECTIONS

SURROUND BACK/

SPEAKERS

SINGLE

BI-AMP

E 2

F. PRESENCE

SURROUND

SUR. B

ZONE 3

FRONT

CENTER

FER

ZONE 3

ZONE2/ZONE3

EXTRA SP2

FRONT

SURRO

AXIAL

EXTRA SP1

ZONE2/ZONE3/

F.PRESENCE

Connecting speakers

■ Bi-amp connection

This unit can be connected to speakers that support bi-amp connections. When connecting speakers, connect the FRONT jacks and the SURROUND BACK/BI-AMP jacks as in the diagram below. Configure the bi-amp settings to activate connections.

SPEAKERS

SURROUND BACK/

BI-AMP

DOCK NETWORK

AV 1

AV 2 AV 3 AV 4

(1 BD/DVD)

PHONO

GND

COAXIAL COAXIAL

OPTICAL OPTICAL

abcd ef

ANTENNA

(4 RADIO)

GND

ARC ARC

AV OUT

SINGLE

HDMI OUT

AV 2 AV 3 AV 4

AV 1

(1 BD/DVD)

SELECTABLE

COMPONENT VIDEO

MON.OUT/ZONE OUT

YPBPRYPBP

AV 3

AV 1

AV 2

AV 4

AUDIO 1

AUDIO 2 AUDIO 3 AUDIO 4

MULTI CH INPUT

(2 TV)

ZONE OUT PRE OUT

(3 CD)

CENTER

ZONE 2

FRONT

SURROUND

SUR. BACK

SUBWOOFER

OPTICAL

COAXIAL

SURROUND SURROUND BACK/

ZONE2/ZONE3

EXTRA SP2

FRONT

HDMI

RS-232C

AV 5 AV 6 AV 7

TRIGGER

OUT

REMOTE

MONITOR OUT/ZONE OUT

YPBP

OUT IN OUT

+12V 0.1A MAX.

(SINGLE)

(FRONT)

FRONT/

(REAR)

CENTER

ZONE 3

SURROUND

SUR. BACK

F. PRESENCE

SUBWOOFER

SPEAKERS

BI-AMP

SINGLE

AC IN

FRONT

CENTER

ZONE2/ZONE3/

F.PRESENCE

EXTRA SP1

NOTE

Before making bi-amplification connections, remove any brackets or cables that connect a woofer with a tweeter. Refer to the instruction manuals of speakers for details. When not making bi-amplification connections, make sure that the brackets or cables are connected before connecting the speaker cables.

■ Multi-zone audio system using the internal amplifier of this unit

Connect the speakers in the second zone and the third zone to the EXTRA SP1/EXTRA SP2 jacks as in the diagram below.

Zone3 J1 Zone2 J1

EXTRA SP2

ZONE2/ZONE3

DOCK NETWORK

AV 1

AV 2 AV 3 AV 4

(1 BD/DVD)

PHONO

GND

COAXIAL COAXIAL

abcd ef

ANTENNA

(4 RADIO)

HDMI

HDMI OUT

AV 2 AV 3 AV 4

AV 5 AV 6 AV 7

AV 1

(1 BD/DVD)

ARC ARC

SELECTABLE

COMPONENT VIDEO

AV OUT

MON.OUT/ZONE OUT

YPBPRYPBP

AV 3

AV 1

AV 2

AUDIO 1

AUDIO 2 AUDIO 3 AUDIO 4

(2 TV)

(3 CD)

FRONT

OPTICAL OPTICAL

OPTICAL

COAXIAL

ZONE2/ZONE3

GND

EXTRA SP2

MULTI CH INPUT

SURROUND

AV 4

CENTER

SUR. BACK

SUBWOOFER

SURROUND SURROUND BACK/

ZONE OUT PRE OUT

ZONE 2

REMOTE

MONITOR OUT/ZONE OUT

YPBP

OUT IN OUT

(SINGLE)

(FRONT)

FRONT/

(REAR)

ZONE 3

SURROUND

SUR. BACK

F. PRESENCE

SUBWOOFER

SPEAKERS

CENTER

BI-AMP

SINGLE

ZONE2/ZONE3/

F.PRESENCE

EXTRA SP1

RS-232C

TRIGGER

OUT

+12V 0.1A MAX.

CENTER

AC IN

FRONT

ZONE2/ZONE3/

F.PRESENCE

EXTRA SP1

CAUTION

The EXTRA SP jacks of this unit should not be connected to a Passive Loudspeaker Selector Box or more than one loudspeaker per channel. Connection to a Passive Loudspeaker Selector Box or multiple speakers per channel could create an abnormally low impedance load resulting in amplifier damage. See this owner’s manual for correct usage. Compliance with minimum speaker impedance information for all channels must be maintained at all times. This information is found on the back panel of this unit.

■

Changing speaker impedance

This unit is configured for 8 Ω speakers at factory setting. When connecting to 6 Ω speakers, carry out the following procedure to switch to 6 Ω. When this unit is configured for 6 Ω speakers, 4 Ω speakers can also be used as the front speakers.

Switch this unit to the standby mode.

Press MAIN ZONE A while pressing and holding STRAIGHT on the front panel.

Release the keys when “ADVANCED SETUP” is displayed on the front panel display. After approximately a few seconds, the top menu item is displayed. J2

MAIN ZONE A

STRAIGHT

Continues to the

1 : EXTRA SP1 jacks can be assigned to Zone3 and EXTRA SP2 jacks can be

assigned to Zone2 by using “Power Amp Assign” (☞

2 : Refer to the “Extended functionality that can be configured as needed

(Advanced Setup menu)” (☞

p. 120) for details on the Advanced Setup menu.

p. 93).

En 21

Check that “SPEAKER IMP.” is displayed on the

FRONT

(

)

( REAR

)

SUBWOOFER

(

)

SUR. BACK

SURRUND

front panel.

■

Connecting speakers

This type of jack can connect to the following speakers or connection.

CONNECTIONS

■

Connecting the subwoofers

Connecting speakers



SPEAKERIMP. 8MIN

Press STRAIGHT repeatedly to select a “6ΩMIN.”

Switch this unit to the standby mode, and then switch it on again.

The power turns on, when the settings you made has been configured.

• Front L/R speakers

• Center speaker

• Surround L/R speakers

• Surround back L/R speakers

• Presence L/R speakers

• Zone2/Zone3 speakers

• Bi-amp connection (Front L/R speakers)

Remove approximately 10 mm of insulation from the ends of the speaker cables, and twist the bare wires

of the cables together firmly so that they will not cause short circuits.

Loosen the speaker terminals.

Insert the bare wire of the speaker cable into the gap on the side of the terminal.

Tighten the terminal.

Connect the subwoofer input jack to the SUBWOOFER 1 and/or 2 jack on this unit with an

audio pin cable. J1

Set the subwoofer volume as follows.

Volume: Set to approximately half volume (or slightly less than half).

Crossover frequency (if available): Set to maximum.

CROSSOVER/

VOLUME

MIN MAX

Subwoofer examples

HIGH CUT

MIN MAX

NOTE

After connection, applying this setting to this unit is required to activate all speaker connections. With using “Power Amp Assign” function, you can easily apply the speaker configuration. Refer to “Power Amp Assign” (☞ “Power Amp Assign” function.

p. 93) for details on using

1 : When only one subwoofer is used, connect the subwoofer to the

SUBWOOFER1 jack.

En 22

Advanced speaker configuration

Speaker layout utilizing an external power amplifier

More speakers can be used by connecting an external amplifier to this unit’s PRE OUT jacks. The speaker layout specified using the Power Amp Assign function varies when an external amplifier is connected.

Symbols on the table

Front L speaker

Center speaker

Front R speaker

Surround L speaker

Surround R speaker

Surround back L speaker

SBL

Surround back R speaker

SBR

■

Connections of speakers

Connect the speakers to the following jacks according to the speaker layout. Refer to “Front/Center/Surround/Surround back speaker and Subwoofer connection” and “Presence speaker connection” for details on connecting speakers (☞ amplifier” for details on connecting an external amplifier (☞

■

Assigning a speaker configuration

A speaker configuration must be assigned to this unit to activate speakers and an external amplifier. Use the “Power Amp Assign” function to easily apply the appropriate speaker settings to this unit in accordance with speaker configuration.

p. 20). Refer “Connecting an external

Front presence L speaker

Front presence R speaker

Speakers that output sound

depending upon settings

External amplifier

p. 25).

■

Using a hi-fi amplifier to improve front speaker sound quality

■ 9.1-channel speaker layout (7 speakers + subwoofer + external front speakers)

The front speaker channel can be enhanced by using an external amplifier possible of greater output power than this unit.

SBRSBL

■ Connections of speakers

CENTER jack Center speaker

SURROUND jacks Surround L/R speakers

SURROUND BACK jacks Surround back L/R speakers

FRONT (PRE OUT) jacks External amplifier

(for front L/R speakers)

SUBWOOFER (PRE OUT) jack J1 Subwoofer

EXTRA SP1 jacks Presence L/R speakers

■ Assigning a speaker configuration

Power Amp Assign 7ch + FRONT

CONNECTIONS

■

Using an external amplifier to output the presence speaker channel

■ 7.1 + Presence speaker layout (7 speakers + subwoofer + external front presence speakers)

SL SR

The front presence and surround back speaker channels can be output at the same time.

SBRSBL

■ Connections of speakers

FRONT jacks Front L/R speakers

CENTER jack Center speaker

SURROUND jacks Surround L/R speakers

SURROUND BACK jacks Surround back L/R speakers

F.PRESENCE (PRE OUT) jacks External amplifier

(for presence L/R speakers)

SUBWOOFER (PRE OUT) jack J1 Subwoofer

■ Assigning a speaker configuration

Power Amp Assign 7ch + FPR

1 : You can also use two subwoofers by connecting them to both SUBWOOFER1

(FRONT) and SUBWOOFER2 (REAR) jacks.

En 23

■

Using the presence speakers in the main room and speakers in another room

■ 9-1-channel speaker layout (7 speakers + subwoofer + external presence speakers + front speakers (in secondary zone))

■

Using front speakers that support bi-amp connection and front presence speakers

■ 7.1-channel speaker layout (Front speaker (Bi-amp) + 3 speakers + subwoofer + external front presence speakers)

CONNECTIONS

Advanced speaker configuration

■

Using front speakers that support bi-amp connection and surround back speakers

■ 7.1-channel speaker layout (Front speaker (Bi-amp) + 3 speakers + subwoofer + external surround back speakers)

SL SR

SBRSBL

The presence speakers in the main room can be used while the front speakers in another room are used. J1

■ Connections of speakers

FRONT jacks Front L/R speakers

CENTER jack Center speaker

SURROUND jacks Surround L/R speakers

SURROUND BACK jacks Surround back L/R speakers

EXTRA SP1 jacks J2 Zone2 speakers

F.PRESENCE (PRE OUT) jacks External amplifier

(for presence L/R speakers)

SUBWOOFER (PRE OUT) jack J3 Subwoofer

BI-AMP BI-AMP

SL SR

A richer sound field can be created with the simultaneous use of front speakers that support bi-amp connection and front presence speakers.

■ Connections of speakers

FRONT jacks Front L/R speakers (bi-amp)

CENTER jack Center speaker

SURROUND jacks Surround L/R speakers

SURROUND BACK jacks Front L/R speakers (bi-amp)

F.PRESENCE (PRE OUT) jacks External amplifier

(for presence L/R speakers)

SUBWOOFER (PRE OUT) jack J3 Subwoofer

BI-AMP BI-AMP

SBRSBL

Connecting surround back speakers to an external amplifier enables simultaneous use of front speakers that support bi-amp connection and surround back speakers.

■ Connections of speakers

FRONT jacks Front L/R speakers (bi-amp)

CENTER jack Center speaker

SURROUND jacks Surround L/R speakers

SURROUND BACK jacks Front L/R speakers (bi-amp)

SUR.BACK (PRE OUT) jacks External amplifier

(for surround back L/R speakers)

SUBWOOFER (PRE OUT) jack J3 Subwoofer

■ Assigning a speaker configuration

Power Amp Assign 7ch + FPR + 1ZONE

1 : Sound cannot be output from the surround back speakers when it is output from

speakers connected to the EXTRA SP1 jacks.

2 : EXTRA SP1 jacks can be assigned to the Zone3 speakers with “Power Amp

Assign” (☞

p. 93).

■ Assigning a speaker configuration

Power Amp Assign 5ch BI-AMP + FPR

3 : You can also use two subwoofers by connecting them to both SUBWOOFER1

(FRONT) and SUBWOOFER2 (REAR) jacks.

■ Assigning a speaker configuration

Power Amp Assign 5ch BI-AMP + SB

En 24

■

FRONT

(

)

(FRONT)

SUBWOOFER

()()

MAX

Using front speakers that support bi-amp connection, surround back speakers and front presence speakers

■ 9.1-channel speaker layout (Front speaker (Bi-amp) + 3 speakers + subwoofer + external surround back speakers + external front presence speakers)

BI-AMP BI-AMP

SL SR

SBRSBL

When an external amplifier is used, front presence speakers and surround back speakers can be used simultaneously with front speakers that support bi-amp connection. J1

■ Connections of speakers

FRONT jacks Front L/R speakers (bi-amp)

CENTER jack Center speaker

SURROUND jacks Surround L/R speakers

SURROUND BACK jacks Front L/R speakers (bi-amp)

SUR.BACK (PRE OUT) jacks External amplifier

F.PRESENCE (PRE OUT) jacks External amplifier

SUBWOOFER (PRE OUT) jack J2 Subwoofer

■ Assigning a speaker configuration

Power Amp Assign 5ch BI-AMP + SB + FPR

(for surround back L/R speakers)

(for presence L/R speakers)

Connecting an external amplifier

The same channel signals are output from the jacks of the PRE OUT and ZONE OUT terminals as from their corresponding SPEAKERS terminals. When connecting an external power amplifier (pre-main amplifier) to enhance speaker output, connect the input terminals of the power amplifier to the PRE OUT and ZONE OUT terminals of this unit.

NOTES

• When a component is connected to the PRE OUT and ZONE

OUT terminals, do not connect speakers to the SPEAKERS

terminals corresponding to those PRE OUT and ZONE OUT

terminals.

• When an external amplifier equipped with a volume adjustment

function is connected, a sufficient volume level may not be

achieved.

Use of the following components is recommended.

– An amplifier with no volume adjustment function. – An integrated amplifier equipped with a function that bypasses

volume circuitry, such as the Yamaha A-S2000 with MAIN IN

input.

CONNECTIONS

Advanced speaker configuration

(SINGLE)

SUR. BACK

ENTER

OUT

REAR

REMOTE

OUT

+12V 0.1A

CENTER

MONITOR OUT/ZONE OUT

ZONE OUT PRE OUT

ENTER

BACKSUBWOOFER

URROUN

ZONE 2

ZONE 3

FRONT/

F. PRESENCE

SPEAKER

URROUND BACK

SURROUND

cde fab

a ZONE2 jacks

Zone2 channel output jacks.

b ZONE3 jacks

Zone3 channel output jacks.

c FRONT/F.PRESENCE (PRE OUT) jacks

Front channel or front presence channel output jacks.

d SURROUND (PRE OUT) jacks

Surround channel output jacks.

e SUR. BACK (PRE OUT) jacks

Surround back output jacks. When you only connect one external amplifier for the surround back channel, connect it to the SUR. BACK (SINGLE) jack.

f CENTER (PRE OUT) jack

Center channel output jack.

NE2/ZONE3 .PRESEN

1 : An external amplifier equipped with four channels is required for this speaker

layout.

2 : You can also use two subwoofers by connecting them to both SUBWOOFER1

(FRONT) and SUBWOOFER2 (REAR) jacks.

En 25

Connecting external components

COMPONEN

AV 1

CONNECTIONS

Jacks and cables

This unit is equipped with the following input/output jacks. Use jacks and cables appropriate for components that you are going to connect.

■

Audio/Video jacks

HDMI jacks

Digital video and digital sound are transmitted through a single jack. Only use an HDMI cable.

AV 1

• Use a 19-pin HDMI cable with the HDMI logo.

• We recommend using a cable less than 5.0 m long to prevent signal quality degradation.

• When a TV that supports HDMI functions and Audio Return Channel function is connected, audio

output from the TV can be input to this unit (☞

• When a player and TV that support the 3D video format are connected to this unit, 3D content can be

played back.

• If you connect this unit to a component that has a DVI jack, an HDMI/DVI-D cable is required.

■

Analog video jacks

p. 126).

COMPONENT VIDEO jacks

The signal is separated into three components: luminance (Y), chrominance blue (P Use component video pin cables with three plugs.

B), and chrominance red (PR).

HDMI cable

Component video pin cable

S-VIDEO jacks

To transmit S-video signals that include luminance (Y) and chrominance (C) components. Use S-video cables.

S-video cable

■

Audio jacks

OPTICAL jacks

These jacks transmit optical digital audio signals. Use fiber-optic cables for optical digital audio signals.

Digital audio fiber-optic cable

AUDIO jacks

These jacks transmit conventional analog audio signals. Use stereo pin cables, connecting the red plug to the red R jack, and the white plug to the white L jack.

Stereo pin cable

VIDEO jacks

These jacks transmit conventional analog video signals. Use video pin cables.

AV 1

Video pin cable

COAXIAL jacks

These jacks transmit coaxial digital audio signals. Use pin cables for digital audio signals.

Digital audio pin cable

En 26

CONNECTIONS

SURROUND

SURROU

CENT

AV 3

BI-AMP

AV 3

(

)

(3 CD)

SURROUND

OUT

def

PBP

BPR

SURROUND

(SINGLE)

(

)

Connecting external components

Connecting a TV monitor

This unit is equipped with the following four types of output jack for connection to a TV. HDMI OUT 1-2, COMPONENT VIDEO, S-VIDEO or VIDEO. Select the proper connection according to the input signal format supported by your TV.

HDMI OUT 1-2 jacks

HDMI OUT

ARC ARC

SELECTABLE

VIDEO jack

MON.OUT/ZONE OUT

(MONITOR OUT)

AUDIO

AUDIO 2AUDIO

S-VIDEO jack

2 TV

UDIO 4

(MONITOR OUT)

PTICALOPTICAL

AXIAL

ZONE2/ZONE

FRON

When connecting to an HDMI compatible TV

Video signal such as component video, S-video and video received by this unit is converted to HDMI and output to the TV. Just select HDMI input on the TV to view video from any external source connected to this unit. J1

Input Output

HDMI

COMPONENT

VIDEO

COMPONENT VIDEO jacks

(MONITOR OUT)

1 BD/DVD

OMPONENT VIDE

MULTI CH INPUT

Y P

R. BACKSUBWOOFE

HDMI

HDM

MONITOR OUT/ZONE OUT

YPBP

ZONE OU

ENTE

ZONE

FRONT . PRESENCE

SPEAKERS

ND BACK

PRE OUT

R. BACK

HDMI input

When connecting to a non-HDMI compatible TV

Connect to the TV using the same type of connection that you used to connect to the external component, and change the inputs on your TV to match that of the external component you are using for playback. If the external component and TV are equipped with different types of analog video jacks, this unit will convert the component video, S-video or video signal to component video, S-video or video signal, according to the type of video input jacks used by the TV. J2, J3

Through

Converted

Input Output

COMPONENT

VIDEO

S VIDEO

VIDEO

COMPONENT

VIDEO

S VIDEO

VIDEO

Component video input

S-video input

Video input

S VIDEO

VIDEO

Through

Converted

1 : You can change the resolution and aspect ratio when converting to HDMI to suit your requirements (☞p. 98).

2 : Set “Analog to Analog Conversion” to “On” (☞p. 98).

3 : Analog to analog conversion is available only for 480i/576i-resolution video signal.

En 27

CONNECTIONS

ANTENNA

PHONO

GND

(1 BD/DVD)

AV 2

AUDIO

(

)

(3 CD)

AUDIO

AV O

abc

def

PBP

(

)

MFM

(

OUT

SINGLE

(

)

(3 CD)

OUT

(RE

(FR

SUBW

((

ARC

(SINGLE)

(

AV 1

OUT

(1 BD/DVD)

AV 2

(

)

(3 CD)

AUDIO 2AUDIO 3AUDIO 4

AV OUT

abcde

CARC

AV 1

(

)

Connecting external components

■

Connecting an HDMI video monitor

Connect the HDMI cable to one of the HDMI OUT 1-2 jacks.

HDMI input

HDMI

HDMI OUT

ARC ARC

SELECTABLE

MON.OUT/ZONE OUT

HDMI

2 AUDIO 3AUDIO

2 TV

PTICA

AXIA

XTRA SP

1 BD/DVD

OMPONE

ONE2/ZONE

LTI

RON

URROUND

HDMI

DOCK NETWORK

AV 1

V 3AV

AXIALCOAXIALOPTICALOPTICA

4 RADI

Projector

• Use a 19-pin HDMI cable with the HDMI logo.

• We recommend using a cable less than 5.0 m long to prevent signal quality degradation.

• When a TV that supports the HDMI function and Audio Return Channel function is connected, audio

output from the TV can be input to this unit (☞

p. 126).

• When a player and TV that support the 3D video format are connected to this unit, 3D content can be

played back.

• This unit is equipped with HDMI OUT 1 and 2 jacks. The active HDMI OUT jack(s) can be selected

(☞

p. 47). The active HDMI OUT jack(s) can be registered with the SCENE function (☞p. 83).

■

Connecting a component video monitor

Connect the component video cable to the COMPONENT VIDEO (MONITOR OUT) jacks.

HDMI

ELECTABLE

N.OUT/ZONE OUT

DIO 1

AUDIO 2 AUDIO 3AUDIO

2 TV

OPTICA

COAXIA

XTRA SP

■

Connecting a S-video monitor

1 BD/DVD)

OMPONENT VIDE

LTI CH INPUT

RON

URROUNDSUR. BAC

ONE2/ZONE

URROUND

CENTE

UBWOOFER

ZONE OUT

NE 2

MONITOR OUT/ZONE OUT

YPBP

FRONT/

. PRESENC

PEAKER

URROUND BACK/

BI-AMP

URROUNDSUR. BAC

ENTE

Component video input

COMPONENT

VIDEO

Connect the S-video cable to the S-VIDEO (MONITOR OUT) jack.

DOCK NETWORK

PHON

GND

OAXIALCOAXIALOPTICAL OPTICALOPTICA

ANTENNA

4 RADIO

GND

3AV

HDMI

MON.OUT/ZONE OU

AUDIO 1

2 TV

ELECTABL

(1 BD/DVD)

COMPONE

MULTI

S-video input

VIDEO

ONE2/ZONE3

RONTSURROUND

OAXIA

XTRA SP

1 : The video signal for the COMPONENT VIDEO or S-VIDEO jacks is converted and output from HDMI OUT 1-2 jacks.

When connecting to a TV via the HDMI jack, you do not need to use these jacks.

En 28

CONNECTIONS

ANTENNA

OUT

(1 BD/DVD)

AV 2

(

)

(3 CD)

AUDIO 2AUDIO 3AUDIO 4

AV OUT

abcde

CARC

AV 1

(

)

(1 BD/DVD)

DOC

SURROUND

COMPONEN

OUT

abc

PBP

OUT

ARC

(

)

GND

(

Connecting external components

■

Connecting a video monitor

Connect the video pin cable to the VIDEO (MONITOR OUT) jack.

DOCK NETWORK

PHON

GND

OAXIALCOAXIALOPTICAL OPTICALOPTICA

4 RADIO

3AV

HDMI

ELECTABL

MON.OUT/ZONE OUT

AUDIO 1

2 TV

(1 BD/DVD)

COMPONE

MULTI

ONE2/ZONE3

RONTSURROUND

OAXIA

Video input

VIDEO

XTRA SP

■ Listening to TV audio

To transmit sound from the TV to this unit, connect as followings according to the TV:

When using a TV that supports the Audio Return Channel function and HDMI Control function

When your TV supports both HDMI Control (e.g., Panasonic VIERA Link) and Audio Return Channel functions, audio/video output from the unit to the TV and audio output from the TV to the unit are possible using a single HDMI cable. The input source is switched automatically to match operations carried out on the TV, and that makes TV sound control easier to use. For the connections and settings, refer to “Single HDMI cable input to TV audio with Audio Return Channel function” (☞

p. 126).

When using a TV that supports the HDMI Control functions

When using a TV that supports HDMI Control functions (e.g., Panasonic VIERA Link), if HDMI Control functions are enabled on the unit, then input source can be switched automatically to match operations carried out on the TV. For the connections and settings, refer to “Switching the input source on this unit automatically when listening to TV audio” (☞

p. 125).

When using other TVs

To transmit sound from the TV to this unit, connect the TV’s audio output to the AUDIO1-4 jacks.

TV audio output Connection

Optical digital audio output Connect to the OPTICAL jack of the AUDIO1 with a fiber-optic cable.

Coaxial digital audio output Connect to the COAXIAL jack of the AUDIO2 with a digital audio pin

cable.

Analog stereo output Connect to one of the AUDIO1-4 with a stereo pin cable.

Select the input source connected via TV’s audio output jack to enjoy the TV sound. If the TV supports optical digital audio output, we recommend that you connect the TV audio output to the receiver’s AUDIO1 jack. Connecting to AUDIO1 allows you to switch the input source to AUDIO1 with just a single key operation using the SCENE function (☞

Audio output

(Optical, coaxial, or analog)

OPTICALCOAXIALAUDIO

p. 49).

K NETWOR

V 1

PHON

AXIA

Available input jacks

HDMI OUT

ELECTABL

MON.OUT/ZONE

AUDIO 1

(2 TV)

OPTICAL

AV 2 AV 3AV

AXIALOPTICALOPTICA

4 RADI

V 2

AUDIO 2 AUDIO 3 AUDIO 4

(3 CD)

COAXIAL

ONE2/ZONE3

EXTRA SP

1 BD/DVD

MULTI

FRON

You can control your TV using the receiver’s remote control by entering the TV’s remote control code (☞

p. 112).

1 : The video signal for the VIDEO jacks is converted and output from HDMI OUT 1-2 jacks. When connecting to a TV via the

HDMI jack, you do not need to use these jacks.

En 29

CONNECTIONS

SOURC

TUNERDOC

[

]

[

]

AV 3

AUDIO

OUT

(

)

(FRONT)

SUBWOOFER

()()

OUT

+12V 0.1A MAX

(SINGLE)

ANTENNA

(1 BD/DVD)

(2 TV)

(3 CD)

FRONT

SURROUND

COMPONEN

OUT

abcde

PBP

OUT

ARC

ECEIVE

Connecting external components

PHONO

Connecting BD/DVD players and other devices

ENTER

V-AUX

OPTION

LTI

This unit has the following input jacks. Connect them to the appropriate output jacks on the playback devices such as BD/DVD players.

Input jack Video input Audio input

AV 1 J1 HDMI/Component video/S-video/Video HDMI/Coaxial digital/Analog (Stereo)

AV 2 J1 HDMI/Component video/S-video/Video HDMI/Coaxial digital/Analog (Stereo)

AV 3 J1 HDMI/Component video/S-video/Video HDMI/Optical digital/Analog (Stereo)

AV 4 J1 HDMI/Component video/S-video/Video HDMI/Optical digital/Analog (Stereo)

AV5 HDMI HDMI

AV6 HDMI HDMI

AV7 HDMI HDMI

AUDIO1 — Optical digital/Analog (Stereo)

AUDIO2 — Coaxial digital/Analog (Stereo)

■ Receiving video signals from the HDMI jack and audio signals from jacks other than HDMI

This unit can use the AV1-4 or AUDIO1-4 input jacks to receive audio signals from other input jacks. For example, if a playback device cannot produce audio signals from an HDMI jack, use the following method to change the audio input.

HDMI/Audio (Optical)

output

HDMI

OPTICAL

BD/DVD player

DOCK NETWOR

PHON

AXIALCOAXIALOPTICALOPTICALOPTICAL

(4 RADIO)

DMI OUT

ELECTABL

MON.OUT/ZONE

UDIO

AUDIO 2AUDIO 3AUDIO 4

AXIA

EXTRA SP

AV 1

(1 BD/DVD)

HDMI

V 2

ULTI

NE2/ZONE

AUDIO3 — Analog (Stereo)

AUDIO4 — Analog (Stereo)

VIDEO AUX HDMI/S-video/Video HDMI/Optical digital/Analog (Stereo)

Press dInput selector to choose an input source (AV1-4, V-AUX, AUDIO1-4, or PHONO).

PHONO — Analog (for turntable connection only)

Press pOPTION to enter the Option menu.

■

Connecting BD/DVD players and other devices with

HDMI cable

Connect the device with an HDMI cable to one of the HDMI jacks of the AV1-7. The HDMI IN jack of the VIDEO AUX on the front panel can also be used. Select the input source (AV1-7 or V-AUX) that the playback device is connected to for playback.

HDMI output

HDMI

AV 1 AV 2 AV 3 AV 4

(1 BD/DVD)

COMPONENT VIDEO

HDMI

MULTI CH INPUT

HDMI

AV 5 AV 6 AV 7

TRIGGER

ONITOR OUT/ZONE OU

ENTE

PRE OUT

REMOT

Press iCursor B / C to choose “Audio Select” and press

iENTER.

Press iCursor D / E to choose an audio input jack and press

iENTER.

Once setup is complete, press pOPTION to close the Option menu.

FRONT

BD/DVD player

1 : Coaxial digital and optical digital jack function can be assigned to other AV jacks using “Input Assignment.” Refer to “Input Assignment” for details (☞p. 105).

SURROUNDSUR. BACK

SUBWOOFE

ZONE

F. PRESENCE

FRONT/

ZONE

SURROUNDSUR. BACK

REAR

ENTE

En 30

+ 128 hidden pages