Page 1
POWER SUPPLY (PW) BENCH
CHECK JUMPERS
YAMAHA CORPORATION OF AMERICA
6600 Orangethorpe Avenue, P.O. Box 6600
Buena Park, CA 90622-6600 (714) 522-9011
Page 2
DISCLAIMER
Every reasonable effort has been made to insure that this document contains
accurate information however, no responsibility is assumed for the use of this
material or for any inaccuracies and/or omissions that may exist.
COPYRIGHT NOTICE
Copyright 2000
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, transmitted in any form by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of YAMAHA.
YAMAHA ® is a registered trademark
Page 3
PW BENCH CHECK JUMPER
When bench testing the PW Power Supply without a console connected, you must jumper certain pin at
the DC output plug. Please see the list below:
PW5000
POWER SUPPLY FOR PM5000
Connector Wiring
PIN FUNCTION PIN FUNCTION
1 -16V 15 +16V
2 -16V 16 + - 16V GND
3 FRAME G 17 +12VG
4 -16V 18 +12CG
5 -16V 19 +48V
6 + - 16V GND 20 CAUTION LED
7 +12VG 21 +16V GND
8 REMOTE 22 +12V
9 +16V 23 +12V
10 +16V 24 +48V GND
11 + - 16V GND 25 +12V
12 +12VG 26 +12V
13 REMOTE 27 +12V
14 +16V
PW5000 for PM5000
To bench test short pins:
3, 6, 7, 8, 11, 12, 13, 16, 17, 18, 21, 24
PW4000: Power supply for PM3500, PM3500M, PM4000 and PM4000M
Connector Wiring
PIN FUNCTION PIN N FUNCTION PIN N FUNCTION
1 -19V blue) 10 19 GND
(Black)
2 -19V (blue) 11 19 GND (black) 20 +48V (orange)
3 FRAME GND
(green)
4 -19V (blue) 13 +19V (red) 22 +12V (purple)
5 -19V (blue) 14 +19V (red) 23 +12V (purple)
6 FRAME GND
(green)
7 FRAME GND
(green)
8 +19V (red) 17 12 GND (white) 26 REMOTE (white)
9 +19V (red) 18 12 GND (white) 27 +12V (purple)
Need 3 jumpers
Jumper 1 Connected the Pin 3 and Pin 10 to Pin 25 and 26.
Jumper 2 Connected the Pin 7 to Pin 12.
Jumper 3 Connected the Pin 6 to Pin 21.
to turn on the Power Supply
12 12 GND (white) 21 48V GND (brow)
15 19 GND (black) 24 PW CAUTION (red )
16 19 GND (black) 25 REMOTE (red )
19 PM CAUTION (+)
(white )
Page 4
PW3000M: Power Supply for M3000, M3000A and M2500
Connector Wiring
PIN
1
2 +15 (red)
3 GND15V (black)
4 GND 48V (black)
5 -15V (blue)
6 +12V (yellow)
7 GND 12V (black)
8 Power supply remote
9 48V (orange)
10 FRANE GND (black)
Need 1 jumper to turn on the Power Supply
PW3000MA: Power Supply for M3000, M3000A and M2500
Connector Wiring
Pin
1
2 +15 (red)
3 GND15V (black)
4 GND 48V (black)
5 -15V (blue)
6 +12V (yellow)
7 GND 12V (black)
8 Power supply remote (white)
9 48V (orange)
10 FRANE GND (black)
Need 1 jumper to turn on the Power Supply
PW2000M Power Supply for M2000
Connector Wiring
PINS FUNCTIONS
1 E 48V (GY)
2 E 12V (white)
3 E 17V (black)
4 +48V (orange)
5 +12V (brown)
6 +17V ( red)
7 -17V (blue)
8 FRANE GND (green)
9 DETECT A (purple)
10 DETECT B (BLU)
Need 1 Jumper for turn on Power Supply
Power supply remote
(brow)
(white)
Connected Pin 1 to Pin 7 and Pin 8
Power supply remote (brow)
Connected Pin 1 to Pin 7 and Pin 8
Connected Pin 9 to Pin 10
Page 5
PW1800: Power Supply for PM1800 and PM1800A
Connector Wiring
PINS FUNCTION
1 E 48V(black)
2 E 12V (white)
3 E 17V (black)
4 +48V (yellow)
5 +12V (brown)
6 +17V ( red)
7 -17V (blue)
8 FRANE GND (green)
9 DETECT A (purple)
10 DETECT B (GREEN)
Need 1Jumper for turn on Power Supply
Connected Pin 1 to Pin 10
PW3000 and PW3000A for PM3000
Connector Wiring
CONNECTOR A CONNECTOR B
PIN FUNCTION PIN FUNCTION
1 +20V 1 +12V
2 DETECT A 2 +48V
3 -20V 3 E(+48V)
4 +20V 4 +12V
5 +20V 5 +12V
6 -20V 6 E(+12V)
7 -20V 7 E(+12V)
8 E ( + 20V ) 8 GND
9 E ( +20V ) 9 DETECT B
10 E ( +20V ) 10 E(12V)
The PW3000 and PW3000A need to 2 Jumpers for tune on power.
Jumper 1Connector A Pin 2 to Connector B Pin 9.
Jumper 2
Connector A Pins 8, 9 and 10 to Connector B Pins 3, 6, 7, 8 and Pin 10
Page 6
PW800 Power Supply for PM5D
Connector Wiring
PIN FUNCTION PIN FUNCTION
1 +24 V 13 GND
2 +24V 14 GND
3 +24V 15 GND
4 +24V 16 GND
5 +24V 17 GND
6 +24V 18 GND
7 +24V 19 CAUTION (+)
8 +24V 20 CAUTION (-)
9 +24V 21 DETECT A
10 GND 22 DETECT B
11 GND 23 DETECT GND
12 GND Frame GND
PW800 need 1 Jumpers
Short Pins
Pin 21, 22 and pin 23