Yamaha DVX-S303, DVX-S301, DVX-S302 User Manual

CA
OWNER’S MANUAL
MODE D’EMPLOI
Active Servo Processing Subwoofer System with a built-in power amplifier. The subwoofer system (NX-SW300 and NX-SW301) employs Advanced Yamaha Active Servo Technology which YAMAHA has developed for reproducing higher quality super­bass sound. This super-bass sound adds a more realistic, theater-in-the-home effect to your stereo system.
Features
Playable disc formats
This receiver can play the disc types associated with the logos shown below. (Do not attempt to load any other type of disc into the receiver, or the receiver may be damaged.)
English
Sound field features
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “MLP Lossless” and the double-D symbol are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc.
“DivX”, “DivX Certified”, and associated logos are trademarks of DivXNetworks, Inc and are used under license.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
DIGITAL VIDEO
SUPER VIDEO
1
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
* Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
DO NOT OPEN
QUALIFIED SERVICE PERSONNEL.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
IMPORTANT Please record the serial number of this unit in the space below.
MODEL:
Serial No.:
The serial number is located on the bottom of the unit. Retain this Owner’s Manual in a safe place for future reference.
10 Protect the power cord from being walked on or pinched
particularly at the plugs, convenience receptacles, and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when unused
for a long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15 Be sure to allow spaces of at least 10 cm above, behind and on
both sides of DVR-S300, and at least 1m above, 30cm behind and on both sides of NX-SW300 and NX-SW301.
16 Do not place the following objects on this unit:
A vessel with water in it. If the vessel falls by vibrations and water spills, it may cause damage to the unit, and/or you may get an electric shock. Apparatus shall not be exposed to dripping or splashing.
i
IMPORTANT SAFETY INSTRUCTIONS
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2 IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.
3 NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., 6660 Orangethorpe Ave. Buena Park, CA90622. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
INVISIBLE LASER RADIATION WHEN OPEN
CAUTION:
DO NOT STARE INTO BEAM INVISIBLE LASER RADIATION WHEN OPEN
DANGER:
AVOID DIRECT EXPOSURE TO THE BEAM
The name plate is located on the bottom of the unit.
La plaquette signalétique est placée sur le panneau de fond de l’appareil.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a qualified service person should remove the cover or attempt to service this device.
DANGER
This unit emits visible laser radiation when open. Avoid direct eye exposure to beam. When this unit is plugged into a wall outlet, do not place your eyes close to the opening of the disc tray and other openings or look inside.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
SÉCURITÉ LASER
L'appareil utilise un laser. En raison des risques de blessure des yeux, le retrait du couvercle ou les réparations de l'appareil devront être confiés exclusivement à un technicien d'entretien qualifié.
DANGER
Risque d'exposition au laser en cas d'ouverture. Eviter toute exposition au faisceau. Lorsque cet appareil est branché à la prise de courant, ne pas approcher les yeux de l'ouverture du plateau changeur et des autres ouvertures pour regarder à l'intérieur.
LASER
Type Laser à semi-conducteur
GaAIAs
Longueur d’onde 650 nm (DVD)
784 nm (VCD/CD) Puissance de sortie 7 mW (DVD/VCD/CD) Divergence de faisceau 60 degrés
LASER
Type Semiconductor laser GaAlAs Wave length 650 nm (DVD)
784 nm (VCD/CD) Output Power 7 mW (DVD/VCD/CD) Beam divergence 60 degrees
AVERTISSEMENT
L’utilisation de commandes et l’emploi de réglages ou de méthodes autres que ceux décrits ci-dessous, peuvent entraîner une exposition à un rayonnement dangereux.
ii
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2
Install this sound system in a well ventilated, cool, dry, clean place with at least 10 cm on the top, 10 cm on the left and right, and 10 cm at the back of DVR-S300 and at least 1 m above, 30 cm
behind and on both sides of NX-SW300 or NX-SW301 for adequate ventilation.
vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, nor locate this unit in an environment with high humidity (i.e., a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit in a location where foreign objects
may fall onto this unit or where this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e., candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall, spilling
the liquid and causing an electrical shock to the user and/ or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use excessive force on switches, knobs and/or cords. 10 When disconnecting the power cord from the wall outlet,
grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Use only the voltage specified on this unit. Using this unit
with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than as specified.
13 To prevent damage by lightning, keep the power cord out and
outdoor antennas disconnected from a wall outlet or the unit during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reason.
15
When not planning to use this unit for long periods of time (i.e., vacation), disconnect the AC power plug from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is faulty.
17 Before moving this unit, press STANDBY/ON to set the unit
in standby mode, then disconnect the AC power plug from the wall outlet.
— away from direct sunlight, heat sources,
18 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet, then leave the unit alone.
19 When using the unit for a long time, the unit may become
warm. Turn the power off, then leave the unit alone for cooling.
20 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003.
This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
iii
CONTENTS
1
1.INTRODUCTION
INTRODUCTION ......................................... 2
Supplied accessories........................................ 5
FUNCTIONAL OVERVIEW ......................... 6
Top and front panels (DVR-S300).................. 6
Rear panel (DVR-S300).................................. 7
Rear panel (NX-SW300)................................. 8
Rear panel (NX-SW301)................................. 8
Remote control (For DVR-S300).................... 9
2.PREPARATION
CONNECTIONS ........................................ 11
Roles and layout of the speakers................... 11
Placing the center speaker ............................. 12
Placing the front/surround speakers.............. 13
Placing the subwoofer ................................... 13
SYSTEM CONNECTIONS........................ 14
Connecting the speakers (DVX-S301).......... 14
Connecting the speakers (DVX-S302).......... 15
Connecting the speakers (DVX-S303).......... 16
Connecting the speaker cables ...................... 17
Connecting the subwoofer............................. 17
Connecting the DVD receiver and the
subwoofer .................................................. 18
OTHER CONNECTIONS........................... 19
Connecting a TV ........................................... 19
Connecting the FM/AM antennas................. 20
Connecting external AV components ........... 21
Connecting digital audio components........... 22
3.BASIC OPERATION
GETTING STARTED................................. 23
Inserting batteries into the remote control .... 23
Using the remote control............................... 23
Setting a TV .................................................. 24
Setting language preferences......................... 26
Setting speaker channels ............................... 27
4.OPERATIONS
DISC OPERATION ................................... 28
Playing discs.................................................. 28
Basic playback controls................................. 28
Selecting various repeat shuffle functions..... 29
Shuffle ........................................................... 29
Other operations for video playback
(DVD/VCD/SVCD)................................... 30
Playing MP3/JPEG/DivX® discs.................. 33
Playing Super Audio CDs ............................. 34
Special features for picture disc playback..... 35
5.ON-SCREEN MENU
DVD SETUP MENU OPTIONS................. 36
General setup menu ....................................... 36
Audio setup menu.......................................... 38
Video setup menu.......................................... 39
Preference setup menu................................... 41
6.OTHER FEATURES
TUNER OPERATIONS ............................. 44
Tuning radio stations ..................................... 44
Presetting radio stations................................. 44
SOUND CONTROLS ................................ 46
Selecting surround sound .............................. 46
Selecting digital sound effects....................... 46
Adjusting the treble/bass level....................... 46
Adjusting the volume level............................ 47
Night listening mode ..................................... 47
Switching to active mode .............................. 47
Switching to standby mode ........................... 47
OTHER FUNCTIONS................................ 48
Setting remote control codes ......................... 48
Controlling other components....................... 48
Dimming the display screen .......................... 49
Setting the sleep timer ................................... 49
Recording on an external AV component ..... 49
TROUBLESHOOTING.............................. 50
GLOSSARY .............................................. 52
SPECIFICATIONS .................................... 54
2
3
4
5
6
English
1

INTRODUCTION

INTRODUCTION

Thank you for purchasing this unit. This Owner’s Manual explains the basic operation of this unit.
Notes about discs
– This receiver is designed for use with the following
discs: Super Audio CD (Super Audio CD), DVD­Video, Video CD, Super Video CD, Audio CD, CD­R, CD-RW, DVD-Audio, DVD+RW, DVD+R, DVD-R, DVD-RW and DVD-RW (VR format).
This receiver can play:
– MP3 and picture (Kodak, JPEG) files recorded on
CD-R(W). – JPEG/ISO 9660 format – Maximum 30 character display –DivX
– CD-R, CD-RW and DVD-RW (VR format) cannot
– Some discs cannot be played depending on the
– Be sure to use only CD-R and CD-RW discs made
– Do not use any non-standard shaped discs (heart-
– Do not use discs with tape, seals, or paste on their
– Do not use discs affixed with labels printed by a
®
disc on CD-R[W]/DVD+R[W]/
DVD-R[W](3.11, 4.x and 5.x)
Notes
be played unless finalized.
recording conditions, such as the PC environment
and application software. The characteristics and
condition of some discs; materials, scratches,
curvature, etc, may result in playback failure.
by reliable manufacturers.
shaped, etc.).
surface. Doing so may damage this receiver.
commercially available label printer.
Cleaning discs
– When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe in a circlar motion.
– Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic spray intended for analog records.
Avoid high temperatures, moisture, water and dust
– Do not expose the system, batteries or discs to
humidity, rain, sand or excessive heat (caused by heating equipment or direct sunlight). Always keep the disc tray closed to avoid getting dust on the lens.
Avoid condensation problem
– The lens may cloud over when the receiver is
suddenly moved from cold to warm surroundings, making it impossible to play a disc. Leave the receiver in the warm environment until the moisture evaporates.
Disc care
– Write only on the printed side of a CD-R/
CD-RW and only with a soft felt-tipped pen.
– Handle the disc by its edge; do not touch the
surface.
Cabinet care
– Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution containing alcohol, spirits, ammonia, or abrasives.
Choosing a suitable location
– Place the receiver on a flat, hard, and stable surface.
2
INTRODUCTION
Region codes
The unit is designed to support the Region Management System. Check the region code number on the disc package. If the number does not match the unit’s region number (see the table below or the back of the unit), the unit may be unable to play the disc.
Destination
U.S.A. and Canada models
U.K. and Europe models
Australia model
Korea, Asia and Taiwan models
Region
code of
DVR-S300
1 1
2 2
4 4
3 3
Playable
discs
ALL
ALL
ALL
ALL
Sound field features
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “MLP Lossless” and the double-D symbol are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc.
“DivX”, “DivX Certified”, and associated logos are trademarks of DivXNetworks, Inc and are used under license.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
1
INTRODUCTION
Active Servo Processing Subwoofer System with built-in power amplifier. This subwoofer system (NX-SW300, NX-SW301) employes Advanced YAMAHA Active Servo Technology which YAMAHA has developed for reproducing higher quality super-bass sound. This super-bass sound adds a more realistic, theater-in-the-home effect to your stereo syetem.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion - and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged
exposure from excessive volume levels.
English
3
INTRODUCTION
DVX-S301 DVX-S302
DVD receiver (DVR-S300)
Subwoofer (NX-SW301)
Center speaker (NX-C301)
DVD receiver (DVR-S300)
Subwoofer (NX-SW301)
Center speaker (NX-C302)
Front/Surround speakers (x4) (NX-S301)
Front/Surround speakers (x4) (NX-S302)
4
INTRODUCTION
DVX-S303
DVD receiver (DVR-S300)
Subwoofer (NX-SW300)
Center speaker (NX-C302)
Supplied accessories
FM wire antenna
AM loop antenna
POWER
SLEEP
DIMMER
Remote control
Batteries (x 2)
Video pin cable
POWER
TV
PROG
REPEAT A - B
TOP MENU/RETURN
MENU
PRESET
SUBTITLEAUDIO ANGLE ZOOM
TV VOL TV CH
EFFECT SURR
TV
INPUT
TV AUX TUNER DVD/CD
SCAN
PAGE
SHUFFLE
ON SCREEN
ENTER
SET UP
NIGHT
TRE
VOL
BASS
MUTE
1
INTRODUCTION
Front/Surround speakers (x 4) (NX-S302)
System control cable (4 m )
Speaker cables (5 m x 3) (15 m x 2)
Fasteners (2 sets)
Base(x 4) (For NX-S302)
Screws (x 8) Washers (x 8) (For NX-S302)
Non-skid pad (1 set) (For NX-SW301)
English
5

FUNCTIONAL OVERVIEW

FUNCTIONAL OVERVIEW
Top and front panels (DVR-S300)
7
8
9
0
654321
A
B
1 STANDBY/ON
Turns on the DVD receiver, or sets it to the standby mode (see “Auto eco power standby mode” on page 28).
2
Opens/closes the disc tray.
3 b / a , w / f
DVD/CD mode: selects the previous/next track or chapter. Press and hold to fast forward or fast reverse. TUNER mode: tunes the radio preset up/down.
4 e
DVD/CD mode: pauses disc playback.
5 INPUT
Selects and input source or sets the priority level for the audio input signals.
6 VOLUME
Adjusts the volume level.
7 Disc tray
Load the disc in the disc tray.
8 System display panel
Shows information about the operational status of the unit. MULTI Lights up when you play a multi-channel audio source. DOWNMIX Lights up when you play discs that allow down mixing of multi-channel audio sources. It does not light up for discs that prohibit down mixing, even if you play a multi-channel audio source.
9 h
DVD/CD mode: starts disc playback. TUNER mode: starts preset radio station installation in Plug & Play mode.
0 s
Exits an operation. DVD/CD mode: stops playback. TUNER mode: erases a preset radio station in Preset mode if held more than two seconds, or stops preset radio station installation in Auto Preset mode.
A Remote control sensor
Point the remote control towards this sensor.
B Head phone jack
Connects headphones.
6
Rear panel (DVR-S300)
(U.K. and Europe models)
FUNCTIONAL OVERVIEW
1
INTRODUCTION
9821 4 5 6 73
AV MONITOR OUT
(DVD ONLY)
1 AC power cord
Connect to a standard AC outlet.
2 AV MONITOR OUT terminal
(U.K. and Europe models only)
Connect to your TV (see page 19).
3 VIDEO output terminal
Connect to the video (composite) jack on your TV (see page 19).
4 COMPONENT VIDEO OUT terminal
Connect the the Y P page 19).
5 LINE OUT terminal
Connect to the AUDIO IN jacks on your VCR.
6 TV IN terminal
Connect to the corresponding AUDIO OUT jacks on your TV (see page 19).
7 AUX IN terminal
Connect to the AUDIO OUT jacks on your VCR or cassette deck.
B/CB PR/CR jacks on your TV (see
Y
P
R PB
COMPONENT
DIGITAL INVIDEO OUT (DVD ONLY)
OPTICAL
PCM/DTS q
DIGITAL
L
R
ANTAMANT
SYSTEM
AUX INTV INLINE OUT
CONNECTOR
VIDEO
S VIDEO
8 FM ANT terminal
Connect the FM antenna.
9 GND and AM ANT terminals
Connect the AM loop antenna.
0 S VIDEO output terminal
Connect to the S-video jack on your TV or VCR.
A OPTICAL DIGITAL IN terminal
Connect to the DIGITAL OUT jack on your digital audio component.
B SYSTEM CONNECTOR terminal
Connect the subwoofer.
FM
GND
75 UNBAL
TO SUBWOOFER
B0A
English
7
FUNCTIONAL OVERVIEW
1 23
Rear panel (NX-SW300)
1 SYSTEM CONNECTOR terminal
Connect to the DVD receiver.
2 SPEAKER terminals
Connect to the speakers.
3 AC power cord
Connect to a standard AC outlet.
Rear panel (NX-SW301)
12
3
1 SYSTEM CONNECTOR terminal
Connect to the DVD receiver.
2 SPEAKER terminals
Connect to the speakers.
3 AC power cord
Connect to a standard AC outlet.
8
FUNCTIONAL OVERVIEW
Remote control (For DVR-S300)
DIMMER
POWER
TV
PROG
REPEAT A - B
TOP MENU/RETURN
MENU
PRESET
SUBTITLE AUDIO ANGLE ZOOM
TV VOL TV CH
EFFECT SURR
TV
INPUT
TV AUX TUNER DVD/CD
4
6
8
0
B
D
F
H
2
1
3
5
7
9
A
C
E
G
ENTER
SLEEP
SCAN
TRE
BASS
POWER
SHUFFLE
ON SCREEN
SET UP
NIGHT
PAGE
VOL
MUTE
I
K M
O
Q
S
U
W
Y
J
L
N
P
R
t
V
X
1 POWER (TV)
Turns on the TV, or sets it to the standby mode.
2 DIMMER
Selects different levels of brightness for the display panel.
3 Numeric keypad (0 – 9)
Enters a track/title number of the disc. Enters a number of a preset radio station.
4 REPEAT
Selects various repeat modes.
5 PROG
DVD/CD mode: starts programming. TUNER mode: starts automatic/manual preset programming if held for more than two seconds.
6 TOP MENU/RETURN
Returns to the previous menu. Displays the top-level disc menu (if available).
7 Cursors ( / / / )
Selects movement direction in the menu.
TUNER mode: press left or right to tune the radio frequency. TUNER mode: press up or down to select auto tuning.
8 ENTER (OK)
Confirms a selection.
1
INTRODUCTION
Note
For details on how to use the remote control, see page 23.
9 MENU
Enters or exits the disc contents menu. For VCD version 2.0 only: In stop mode, turns on/off playback control (PBC) mode. During playback, returns to the main menu.
0 s
Exits an operation.
DVD/CD mode: stops playback. DVD/CD mode: holding down the button will open and close the disc tray. TUNER mode: erases a preset radio station if held for more than two seconds.
A d PRESET u ( b / a )
DVD/CD mode: selects the previous/next track or chapter. Press and hold to fast forward or fast reverse. TUNER mode: press to select a preset radio station.
B SUBTITLE
Selects a subtitle language.
English
9
FUNCTIONAL OVERVIEW
C AUDIO
Selects an audio language (DVD) or an audio channel (VCD).
D TV VOL (+ / –)
Adjusts the TV volume.
E TV CH (+ / –)
Switches the TV channel.
F TV INPUT
Switches the TV input.
G EFFECT
Selects a sound effect.
H Input selection buttons
Selects the appropriate active source mode.
TV mode: switches to TV input. AUX mode: switches to AUX ANALOG/AUX DIGITAL input. TUNER mode: switches tuner (FM/AM) input. DVD/CD mode: switches to DVD/CD mode.
I POWER ( )
Turns on the DVD receiver, or sets it to the standby mode.
J SLEEP
Sets the sleep timer.
K SCAN
Scans each track/chapter on the disc.
R e
DVD/CD mode: pauses disc playback.
S NIGHT
Turns the Night mode on or off.
T ZOOM
Enlarges or reduces the TV screen picture.
U ANGLE
Selects a DVD disc camera angle (if available).
V VOL (+ / –)
Adjusts the volume level.
W TRE/BASS
Selects the TREBLE (high tone) or BASS (low tone) sound mode. Use the VOLUME control to change the tone level.
X MUTE
Mutes or restores the volume.
Y SURR
Selects multi-channel surround or stereo mode.
L PA GE
Turns the pages of DVD-Audio still pictures.
M REPEAT A-B
Repeats a specific section on a disc.
N SHUFFLE
Plays tracks in random order.
O ON SCREEN
Displays the current status or disc information.
P SET UP
Enters or exits the system setup menu.
Q h
DVD/CD mode: starts disc playback.
10

CONNECTIONS

+
+
CONNECTIONS
Roles and layout of the speakers
To enjoy quality sounds you need to place the speakers in their appropriate positions and install them correctly. The following show the recommended layout of the speakers.
DVX-S301
DVD receiver
3
Surround
speaker (L)
Front
speaker (L)
1
Center speaker
4
Subwoofer
2
Front
speaker (R)
1
3
Surround
speaker (R)
DVX-S302/DVX-S303
DVD receiver Center speaker
Front
speaker (L)
1
3
Surround
speaker (L)
4
Subwoofer
2
Front
speaker (R)
1
Surround
speaker (R)
2
PREPARATION
3
For the best possible surround sound, all of the speakers (except the subwoofer) should be placed at the same distance from the listening position.
1 Front Speakers (L, R)
Place the front left/right speakers on both sides of your TV at equal distances. Main roles: Produces front channel (stereo) sounds and effect sounds.
2 Center Speaker
Place on top of the TV or inside the TV rack so that the speaker and TV are aligned vertically. Main role: Produces sounds oriented toward the center of the screen such as dialogues or vocal sounds.
3 Surround Speakers (L, R)
Place the surround left/right speakers behind the listening position. (For NX-S301, we recommend placing them at a height of 1.8 m (6 feet) and pointing them at the listening position.) Main roles: Produces surround sounds and effect sounds.
4 Subwoofer
Place the subwoofer near a front speaker and turn it slightly toward the center of the room to reduce wall reflections. Main roles: Produces bass sounds and low frequency (LFE) sounds contained in Dolby Digital or DTS.
Note
To avoid magnetic interference, do not position the front speakers too close to your TV. Allow adequate ventilation around the DVD receiver and subwoofer. Bass sounds produced by the subwoofer may be heard differently depending on the listening position and subwoofer location. To enjoy desired sounds, try to change the location of the subwoofer according to the listening position.
English
11
CONNECTIONS
+
+
Placing the center speaker
When placing the center speaker on top of the TV, use the supplied fasteners to secure the speaker.
NX-C301
Attaching to a wall
You can attach the speakers to a wall using commercially available screws (Diameter: 3.5 to 4 mm, Length: 25 mm or more). Each speaker requires two screws.
Fastener
Peel off the seal
NX-C302
Fastener
Peel off the seal
1 Peel off the seals on one side of the fasteners and
attach them to the bottom of the center speaker.
2 Peel off the seals on the other side of the fasteners and
attach them to the top of the TV.
Notes
– Do not place the speaker on the TV if the top of the
TV is uneven or narrower than the bottom surface of the speaker. Doing so may cause the speaker to fall. In this case, place the speaker inside a TV rack or on a level floor.
– Before attaching the fasteners to the TV, clean the
surface with a dry cloth. A dirty or wet surface may weaken the adhesive force and cause the speaker to fall.
– Do not touch the bonding surfaces of the fasteners
after peeling off the seals. Doing so may weaken the adhensive force and cause the speaker to fall.this installation. Use metric screw threads only.
NX-C301
110 mm
NX-C302
151 mm
Screws (3.5 to 4 mm dia., commercially available)
20 mm or more
Screws (3.5 to 4 mm dia., commercially available)
20 mm or more
5 mm
5 mm
1 Install two screws in the wall where you want to place
the speaker.
2 Hang the speaker on the screws using the holes in the
back of the speaker.
Notes
– To attach a speaker to a wall using screws, the wall
must be firm. Do not attach a speaker to a wall that is made of weak materials such as plaster or veneered woods. Doing so may cause the speaker to fall.
– When connectiong the speakers, fix the speaker
cables in place so that cables do not loosen. If your foot or hand accidentally gets caught on a loose speaker cable, the speaker may fall.
– After attaching each speaker, check that the
speaker is fixed securely. YAMAHA will bear no reponsibility for any accidents caused by improper installations.
12
Placing the front/surround
+
speakers
Attaching to a wall
You can attach the speakers to a wall using commercially available screws (Diameter: 3.5 to 4 mm, Length: 25 mm or more). Each speaker requires two screws.
NX-S301
40 mm
Screws (3.5 to 4 mm dia., commercially available)
CONNECTIONS
Attaching the base
Attach the base to the bottom of the front/surround speakers (NX-S302) with the supplied base mounting screws as shown below.
Base
mounting
screws
Base
Washer
2
PREPARATION
20 mm or more
5 mm
1 Install two screws in the wall where you want to place
the speaker.
2 Hang the speaker on the screws using the holes in the
back of the speaker.
Notes
– To attach a speaker to a wall using screws, the wall
must be firm. Do not attach a speaker to a wall that is made of weak materials such as plaster or veneered woods. Doing so may cause the speaker to fall.
– When connectiong the speakers, fix the speaker
cables in place so that cables do not loosen. If your foot or hand accidentally gets caught on a loose speaker cable, the speaker may fall.
– After attaching each speaker, check that the
speaker is fixed securely. YAMAHA will bear no reponsibility for any accidents caused by improper installations.
Hanging on a wall (NX-S301)
You can hang the speakers on a wall using a commercially available bracket and screws (Diameter: 6 mm). Attach a bracket firmly to the rear of the speakers using screws. Then mount a screw on the wall where the speaker is to be hung and hook the speaker securely onto the mounted screws.
NX-S302
Note
Placing the speakers (NX-S302) on the places such as hard wooden floor may scratch the surface of the floor.
Placing the subwoofer
Attach the non-skid pads to the bottom of the subwoofer (NX-SW301), and then place the subwoofer on a level hard floor.
Peel off the seal
Note
Using non-skid pads prevents the subwoofer from sliding when it vibrates, and ensure quality sound production.
Note
Do not use screw threads neasured in inches for this installation. Use metric screw threads only.
English
13

SYSTEM CONNECTIONS

+
+
+
+
+
SYSTEM CONNECTIONS
Connecting the speakers (DVX-S301)
Notes
– Do not connect the power cord of the subwoofer and DVD receiver into an AC outlet until all cable connections are completed. – Please refer to the pages below for detailed information on how connect each speaker.
Tab
Red
Front speaker (R)NX-S301
(page 17)
Green
White
Center speaker
NX-C301
(page 17)
Front speaker (L) NX-S301
(page 17)
Gray
DVD receiver (DVR-S300)
Tab
L
R
Surround
speaker (R)
NX-S301
(page 17)
CONNECTOR
Blue
TO SUBWOOFER
SYSTEM
Surround
speaker (L)
NX-S301
(page 17)
14
Subwoofer
(NX-SW301)
Connecting the speakers (DVX-S302)
+
+
+
+
+
+
+
+
Notes
SYSTEM CONNECTIONS
– Do not connect the power cord of the subwoofer and DVD receiver into an AC outlet until all cable connections are completed. – Please refer to the pages below for detailed information on how connect each speaker.
Front speaker (R)
NX-S302
(page 17)
Red
Black
Center speaker
NX-C302
(page 17)
Black
Red
Front speaker (L)
NX-S302
(page 17)
Red
Black
2
PREPARATION
DVD receiver (DVR-S300)
Red
Surround
speaker (R)
NX-S302
(page 17)
Black
Red
L
R
CONNECTOR
TO SUBWOOFER
SYSTEM
Tab
Green
White
Blue
Gray
Tab
Subwoofer NX-SW301
Red
Black
Surround
speaker (L)
NX-S302
(page 17)
English
(page 17)
15
Loading...
+ 45 hidden pages