Yamaha DME DESIGNER V3.0 Manual

Version 3.0

OWNER’S MANUAL

Getting Started

Getting Started with DME Designer

In this manual the abbreviation "DME" refers to the DME64N/DME24N/DME8i-C/DME8o-C/DME4io-C/ DME8i-ES/DME8o-ES/DME4io-ES. The abbreviation "DME Satellite" refers to the DME8i-C/DME8o-C/ DME4io-C/DME8i-ES/DME8o-ES/DME4io-ES. Your DME, SP2060, ICP1 and the DME Designer software, let you build a custom audio system installation that can support an incredible variety of conditions. You can build an entire system from input to output with the DME Designer software, then send the system data to the DME and SP2060 which become independent processors. An amazing variety of applications are possible, including audio installations, sub-mixing, speaker system control, matrix/routing, and multi-effect processing.

NOTE

Here the abbreviation “DME” does not include the “DME32.”

NOTE

This manual is based on the English version of operating system. Illustrations, command names, window names, and similar information are from that version. Some items may differ from what you see on the computer screen, depending on which operating system you are using.

SPECIAL NOTICES

• The software and this Owner’s Manual are the exclusive copyrights of Yamaha Corporation.

• Use of the software and this manual is governed by the license agreement which the purchaser fully agrees to upon breaking the seal of the software packaging. (Please read carefully the Software Licensing Agreement at the end of "About the included CD-ROM" before installing the application.)

• Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer.

•Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software.

• This disc is a CD-ROM. Do not attempt to play the disc on an audio CD player. Doing so may result in irreparable damage to your audio CD player.

• The company names and product names in this Owner’s Manual are the trademarks or registered trademarks of their respective companies.

• The screen displays as illustrated in this Owner’s Manual are for instructional purposes, and may appear somewhat different from the screens which appear on your computer.

• Future upgrades of application and system software and any changes in speciﬁcations and functions will be announced separately.

• Windows® is the registered trademark of Microsoft® Corporation.

DME Designer Owner’s Manual

The DME Audio System Network

In an audio system including one or more DME units and/or SP2060 units, the “control space” is logically organized using the concepts of “Area”, “Zone”, and “Device Group". The space covered by the entire system is the “Area”, while independent sonic spaces within that Area are called" Zone" A group of DME or SP2060 units assigned to the same function are considered a “Device Group”. An Area is comprised of one or more Zones, and each Zone can include up to 32 Device Groups. A single Device Group can include as many as 16 devices. Each Device Group has one “Group Master”.

NOTE

Meter response may deteriorate as the number of meters displayed in a single device group in DME Designer increases. In such cases meter response can be improved by dividing the device group. See “Changing Device Groups” on page 275.

NOTE

DME and SP2060 units cannot be combined in the same Device Group.

NOTE

All devices in a Device Group must be on the same subnet.

Getting Started

Area

Zone1

Zone2

Zone1

Device Group1

Device Group2

Device Group1

Device1 (Group Master)

Device2 (Slave)

DME Designer Owner’s Manual

Getting Started

The DME Designer Software Application

The DME Designer software application provides a convenient, central interface for the creation and control of DME-based audio systems. By connecting the computer on which the DME Designer application is running to a Group Master it becomes possible to control multiple devices simultaneously. With DME Designer, DME audio systems can be designed and conﬁgured via a comprehensive blockdiagram interface on the computer screen.

The main concepts used in the creation of DME audio systems are “Components”, “Conﬁgurations”, “Preset Parameters”, and “Scenes”.

■ Components

Any independent signal-processing block, such as an equalizer, compressor, input/output module, or external device control object is a “Component”.

■ Conﬁgurations

A “Conﬁguration” is group of components, including their placement and interconnections.

DME Designer Owner’s Manual

Getting Started

■ Preset Parameters

The set of parameters for all components in a Conﬁguration is know as the Conﬁguration's “Preset Parameters”.

■ Scenes

A Conﬁguration and its Preset Parameters are a “Scene”.

Composition of scene

Scenes

Scenes1

Scenes2

Scenes999

MATRIX MIXER PARAMETRIC EQ

16 x 8

= Components

Configurations

COMP/LIMITER

8 BAND

PARAMETRIC EQ

DELAY DELAYCROSSOVER

DELAY CROSSOVER

2WAY

DELAY COMP/LIMITER GATE

2WAY

DELAY COMP/LIMITER GATE

PARAMETRIC EQ

COMP/LIMITER GATE

Preset

Parameters

Æ GATE

• Attack

• Decay

• Range

• Threshold

• Key in

• Hold

DME settings as well as Conﬁguration and Preset Parameter settings are sent from the DME Designer application running on the computer to the Device Master via USB or Ethernet, allowing each device to function as a separate processor, independently from the computer. It is also possible to keep the DME Designer application on line and control the devices in real time. It is possible to use the DME Designer to create Conﬁgurations that include multiple devices when the appropriate devices are connected.

Although it is possible to have multiple Zones in an Area, multiple Device Groups in a Zone, and multiple Scenes and Conﬁgurations in a Device Group, only one Area, Zone, Device Group and Conﬁguration can be active and editable via the DME Designer at any one time. The active elements are known as the Current Zone, Current Device Group, Current Scene, and Current Conﬁguration.

DME Designer Owner’s Manual

Getting Started

Data Handled by a DME Audio System

■ DME Data Structure

Common Overall Data

Scene Link Settings Settings required for linked scene operation between multiple

Data for Each Device Group

User Deﬁned Button Settings Settings required for component parameter control from the

Global Parameter Link Settings Settings required for linked operation of the same types of

Data Used by the Scene Manager

MIDI program Change Settings Settings required to allow scene selection via MIDI commands.

Scenes The information required to switch audio data processing

Data for Each Device

Conﬁgurations A combination of the audio signal processing, audio input/

groups.

DME64N/DME24N or ICP1 panel. Up to 24 parameters can be registered for control.

parameters between multiple devices.

setups. Scenes include conﬁgurations and preset data. The Scene Manager facilitates registration and management of scene data. Up to 999 scenes can be registered, and registered scenes are managed by their scene numbers.

output, and external device control components and their interconnections, created to create the desired audio system.

Local Parameter Link Settings

Component Link Settings

External Device Settings

Preset Parameters The settings for the components in a conﬁguration.

Settings that allow linked operation between similar types of internal DME parameters.

Settings that allow linked operation between similar types of internal DME components.

Settings required to allow control of component parameters from external devices. Independent settings are required for each device. The external devices that can be used are as follows:

• MIDI Controller (MIDI Control Change, Parameter Change).

• GPI Controller.

• DAW Controller.

• AMX, Crestron, and other remote controllers.

• PM5D or other compatible mixing console (controlling DME internal head amp)

Audio processing setups can be switched by changing the preset parameters. Components included in the preset parameter set are as follows:

• GEQ, MatrixMixer, and other audio signal processing components.

• Internal AD/DA (DME24N), Cascade (DME64N), and MY card I/O components*.

• Components for external devices such as the AD8HR and AD824 remote head ampliﬁers.

DME Designer Owner’s Manual

* Some settings not included.

■ SP2060 Data Structure

Common Overall Data

Scene Link Settings Settings required for linked scene operation between multiple devices.

Data for Each Device

Scenes The information required to switch audio data processing setups.

Scenes include configurations and preset data, The last Library name recalled is specified. The Scene Manager facilitates registration and management of scene data. Up to 99 scenes can be registered for 12 preset areas and 87 user areas, and registered scenes are managed by their scene numbers.

Configurations A combination of the audio signal processing, audio input/output, and external

device control components and their interconnections, created to create the desired audio system.

Getting Started

Local Parameter Link Settings

Preset Parameters The settings for the components in a configuration.

Data for Each Component

Library Settings specific to the speakers to be used.

Settings that allow linked operation between similar types of internal SP2060 parameters.

Audio processing setups can be switched by changing the preset parameters. Preset parameters can be recalled by SP2060 units, but not edited.

In addition to the preset data provided, settings can be created by the DME Designer.

DME Designer Owner’s Manual

Getting Started

One DME unit/Device Group

Microphone Mixer External Head Amp etc...

Input

Device Group

External Device (MIDI, GPI, DAW, AMX/Crestron, controlling DME internal head amp)

User Defined Button Scene Manager

LCD Display

Dome Low

Dome Mid

Dome Hi

....

Specifies the parameter to be changed.

Assigned Parameter

Crossover: Output Low: Level

Crossover: Output Mid: Level

Crossover: Output Hight: Level

(No Assign)

No.

001

002

003

004

005

006

....

Configuration

Output Processor for Dome

Delay EQ Dyn

MY8-AE

(Input)

Local parameter link settings

External device settings

Delay

Cross-

Over

Output

Scene Name

All On

Opening

Band Set 1

Band Set 2

Band Set 3

...

Power Amp Processor etc...

Confuguration

Output Processor for Dome

...

Specifies the configuration and preset parameters combination.

MY8-AE

(Output)

Preset Parameters

All On

BGM & MC

Band 1

Band 2

Band 3

Set the value

Notes

Audio signal

Control signal

Data explanation

Setting preset parameters

Preset parameters for output processor

All On Component value

BGM & MC

Band 1

Band 2

Band 3

Two DME units/Device Group (When one DME unit doesn’t provide sufficient processing power, up to 16 DME units can be used)

External Device (MIDI, GPI, DAW, AMX/Crestron, controlling DME internal head amp)

Device Group

DME#1

Input Output

Microphone Mixer External Head Amp etc...

For DME#1

For DME#2

Input Output

User Defined Button

LCD Display

Dome Low

Dome Mid

Dome Hi

Hall Low

Hall Mid

Hall Hi

....

Selects the parameter to be edited from two DME units.

DME#1

Configuration

Output Processor for Dome

Local parameter link settings

External device settings

Assigned Parameter

#1: Crossover: Output Low: Level

#1: Crossover: Output Mid: Level

#1: Crossover: Output Hight: Level

#2: Crossover: Output Low: Level

#2: Crossover: Output Mid: Level

#2: Crossover: Output Hight: Level

DME#2

Scene Manager

No.

001

002

003

004

005

006

....

Preset parameters Preset parameters

All On

BGM & MC

Band 1

Band 2

Band 3

Power Amp Processor etc...

Scene Name

All On

Opening

Band Set 1

Band Set 2

Band Set 3

...

Configuration

Output Processor for Dome

...

DME#2

Configuration

Output Processor for Hall

Local parameter link settings

External device settings

For DME#1 For DME#2

Notes

Preset parameters

All On

BGM & MC

Band 1

Band 2

Band 3

Audio signal

Control signal

Data explanation

Setting preset parameters

Configuration

Output Processor for Hall

...

Specifies the configuration and preset data combination in each DME

All On

BGM & MC

Band

Preset parameters

All On

BGM & MC

Band

DME Designer Owner’s Manual

Specifies the parameter to be linked between DME units.

Grobal Parameter Link

NOTE

Separate SP2060 units normally handle scenes independently, but the Scene Link function can be set from the DME Designer to allow linked scene operation.See “Scene Link Manager” on page 141.

System Requirement

Operating System Windows® XP Professional/XP Home Edition/2000 Professional

CPU 1 GHz or better Intel® Core™/Pentium®/Celeron® family processor

Memory 256 MB or more

Hard Disk Capacity 300 MB or more

Display 1,280 x 1,024 pixels or better/High Color 16 bit or better

Getting Started

Other Mouse, CD-ROM drive, 100Base-TX/10Base-T Ethernet or USB connection

Operating System Windows® Vista Ultimate/Business/Enterprise

CPU 1.4 GHz or better Intel® Core™/Pentium®/Celeron® family processor

Memory 1 GB or more

Hard Disk Capacity 300 MB or more

Display 1,280 x 1,024 pixels or better/High Color 16 bit or better

Other Mouse, CD-ROM drive, 100Base-TX/10Base-T Ethernet or USB connection

environment.

DME Designer Owner’s Manual

Getting Started

Main Changes from V1.0 to V1.1

■ Main Panel Window

• Instead of the former Parameter Link function, there are now two functions: a Global Link function that links parameters within all DMEs in a zone and a Local Link function that links parameters within a single DME unit. (page 89)

• The Synchronization function can now not only send data from DME Designer to the DME unit, but can also synchronize by reading data from the DME unit. (page 91)

• Scene Increment/Decrement and Time Adjustment can now be assigned in the GPI input function. (page 108)

• DME unit events can now be recorded by the Event Logger function and displayed in the Event Logger window. (page 164)

• The time for executing an event can now be set by using the Event Scheduler function. (page 133)

• Parameters in the current conﬁguration can now be listed on the display and printed out by using the Parameter List function. ( page 137)

• The Wav File Manager can manage Wave ﬁles played by the Wav File Player. (page 141)

• Settings can be made by the DAW Control function that are used for controlling DMEs from a DAW controller. (page 147)

• DME unit data can now be saved as a backup ﬁle by using the Backup function. (page 147)

■ Designer Window

• The port name display can now be switched between long name display and short name display. (page 190)

• DME64N cascade connections can now be set. (page 205)

• Priority items can now be set when compiling conﬁgurations by using the [Compile Priority] function in the “Preferences” dialog box. (page 204)

• Delay time can now be displayed for each component by using the Show Signal Delay function. (page 287)

• Monitoring points can now be edited by using the “Monitoring Point List” dialog box. (page 288)

• The status of connections in a conﬁguration can now be analyzed in advance by using the Analyze function, without connecting the DME unit. (page 290)

•You can now set the action that occurs when you double-click a user module object. You can also turn user module security ON or OFF, and set a password. (page 291)

• Libraries with component parameters saved in them can now be recalled from the context menu for a component object. (page 348)

•A new rule for wiring prohibits connections to terminals that would short the terminator.

■ Component Editor/Component

•A status bar has been added to the component editor. It displays the component name, component ID, and parameter IDs for parameters that are being edited. (page 302)

•A Snap function has been added that records parameters in the editor temporarily. Parameter sets can then be switched by using the Snap buttons. (page 344)

• The meter's peak hold function can now be turned ON or OFF. (page 341)

•A Wav File Player component has been added for playing Wave ﬁles. (page 409)

• An effect component called SPX has been added that supports many different effect applications, such as reverb, delay, and modulation effects, along with complex combinations of multiple effects. (page 450)

•A Slot Out component editor has been added. (page 462)

• An Undo/Redo function is now available when using the design mode. It can undo the most recent operation (control movement/resize/deletion).

DME Designer Owner’s Manual

Changes from V1.1 to V1.2

■ Main Panel Window

• The synchronization algorithm has been reﬁned for faster synchronization.

• Synchronization now can be executed from DME to DME Designer without any break in the sound.

• In the following cases, synchronization can be executed from DME Designer to DME without any break in the sound:

The second or later synchronization after starting DME Designer* and when differences in data between the DME and DME Designer are limited to parameters within components, AD824/ AD8HR/DME24N AD/DA setting data, or MY card setting parameters.

* If the ﬁle was saved when DME Designer was closed, there will be no break in sound even in the ﬁrst synchronization after saving.

• Compile speed has been increased. Up to three times faster when AutoDelayCompensation is turned On. Up to two times faster when AutoDelayCompensation is turned Off.

• Synchronization is possible when no MY card or a different MY card is installed in the DME unit (a conﬁrmation dialog will appear).

• An option to automatically close the dialog after synchronization has been added. (page 50)

•A progress bar has been added to the Synchronization dialog. (page 49)

•A message appears to warn when synchronization will cause muting.

• The following operations can be performed while on line:

- Scene storage.

- Scene name changes.

- Fade ON/OFF and Fade Mode changes.

- Fade time changes.

- Parameter link setting changes.

• When a scene store is executed, that scene becomes the current scene.

•Wave ﬁles can be saved as DME data ﬁles, and are included in import/export operations. (page 41)

•Wave ﬁles can be saved in the Wav ﬁle library.

• Event Log events can be output via GPI. (page 76)

• The on-line indicator appears as a button which can be used to switch between on-line and off-line. (page 57)

• Scene edits cause the EDIT indicator to appear. (page 55)

• An auto ﬁle save function (Auto Save, post synchronization) has been added. (page 70)

• Different zones can be speciﬁed for use by different users. (page 148)

• Scene parameters related to User Deﬁned Button, Program Change, GPI In and GPI Out can be set via the Scene Manager. (page 79)

• [Select All] and [Clear All] buttons have been added to the Scene Manager Recall Safe dialog. (page 83)

• User Control can be created for individual users as well as security levels. (page 86)

•A Remote Control Setup List has been added. (page 133) This list can be used to make detailed settings for a new software protocol that allow the DME to

be controlled from AMX, Crestron, and similar devices. Refer to the “DME-N Remote Control Protocol Speciﬁcations” document for details about the

communication protocol. Information about the “DME-N Remote Control Protocol Speciﬁcations” document can be found at the Yamaha pro Audio website (URL below).

http://www.yamahaproaudio.com/

• It is possible to specify whether listed events will be executed by the Event Scheduler. (page 133)

Getting Started

DME Designer Owner’s Manual

Getting Started

• The order of same-time events can be changed in the Event Scheduler. (page 133)

• Exceptions can be speciﬁed for Event Scheduler execution day/time. (page 101)

• Event Scheduler execution times can be speciﬁed in 1-second increments. (page 100)

• Head amp gain and MY-Card can be set via GPI, MIDI, User deﬁned Button, DAW Control.

• Parameter values, scene recall, GPI output, Wave ﬁle playback, and head amp gain can be set via the User Deﬁned Buttons. (page 126)

• The Component Lock function dialog is separate from the Parameter List dialog. (page 140)

• Shortcuts can be freely set as required. (page 146)

• Files can be saved in the DME unit. (page 68)

•A [Close All Editor Windows] button has been added to the Window menu. (page 67)

• External head amp parameters will be recognized by the DME unit when either the DME or the external head amp (AD824, AD8HR) are turned on. Execute a scene recall to send DME settings an external head amp.

• This manual is now separate from the DME Designer installer, and can not be accessed from the DME Designer menus.

■ Designer Window

• The following operations can be carried out via the shortcut keys.

- Navigator

- Activate Navigator

- Activate Toolkit

- Activate Design Window

- Select Left Port and Start Wiring

- Select Right Port and Start Wiring

- Wire Auto Single to Right

- Wire Auto Multi to Right

- Wire Auto Single to Left

- Wire Auto Multi to Left

- Delete Wire

• It is now possible to simultaneously edit multiple objects of the same type. Example: Change the thickness or color of multiple wires at once.

• Files related to user modules (user module ﬁles, library ﬁles, user module editor ﬁles) can be combined and exported/imported as a single ﬁle.

• Port colors can be independently speciﬁed for each port type. (page 194)

• Default wire thicknesses and types can be independently speciﬁed for each port type.

• An automatic hot-spot connection function has been added. (page 267)

• Port display has been added to External Device, Picture, DME, and ICP1 objects.

• When drawing wires the keyboard cursor keys can be used to move the mouse cursor, and the <Enter> key can be used to create nodes.

• When drawing wires <Shift> key plus < →> key and <Shift> key plus < ←> key combinations can be used to automatically connect horizontally-aligned hot spots.

• DME object ports can be freely speciﬁed.

• Compilation of conﬁgurations with loop connections is possible when Auto Delay Compensation is On.

• The name has been changed from “Foot Monitor” external device to “Floor Monitor.”

• Addition External Device types have been provided.

• External Devices can be double-clicked to open a ﬁle saved by other applications. (page 216)

• Picture objects can be double-clicked to open a speciﬁed editor. (page 232)

•Text objects can be double-clicked to open a speciﬁed editor. (page 235)

DME Designer Owner’s Manual

Getting Started

• User module port labels can be edited. (page 229)

• Graphics can be placed to represent user modules. (page 228)

• The Legend ﬁeld automatically resizes to accommodate project names and titles of different lengths.

•A Generic “MY-Others” setting has been provided to accommodate third-party MY cards.

■ Component Editor Window

• Undo and Redo are now shortcut compatible.

•A scroll bar appears when the size of the component editor window is reduced.

• The size and position of the component editor window are memorized.

• An option to allow mouse-over zooming of the edit box has been added. (page 305)

•A [Back] button that allows switching between related parent and child windows has been added. (page 302)

•A [Close All Editor Windows] button has been added to the contextual menu.

• Source Selector, Speaker Processor, Limiter, Slot In, Cascade In, and Cascade Out components have been added.

• The Delay algorithm has been revised. (page 381 )

- LEVEL and MUTE are effective when Delay is Off for each channel.

- The name of the overall Delay [On] parameter has been changed to [All Bypass].

Input

Mute

Level

Delay

Mute Level

Delay On

OUT

Mute

Input Level

Delay

On Mute Level

Delay All Bypass

OUT

• The bus send level range for Delay, Matrix, and Matrix Mixer components has been changed to

- ∞ through 0.0 dB.

• Snap copy is possible. (page 345)

• Snap can be retained until the application is quit or another ﬁle is opened.

• Security status is displayed in the user module editor status bar.

• Multiple controllers can be selected by clicking while holding the <Ctrl> key when the editor is in the design mode. (page 340)

• [Picture], [Text], [Box], [Ellipse], and [Frame] have been added to the tool palette of the user module editor and user control editor design mode. (page 307)

• Controller properties can be accessed by double-clicking controllers in the user module editor or user control editor design mode. (page 326)

• Picture and Text objects can be clicked to open a speciﬁed editor in the user module editor or user control editor.

• The User Module Editor and User Control Editor offer a greater range of customization options for color, size. etc., of the placed controls.

■ MIDI Setup

•A MIDI Setup minimize function has been added.

■ V1.2 Precautions

• When using project ﬁles (*.daf) created by version 1.1.5 or earlier, synchronize from the DME Designer to the DME unit for the ﬁrst synchronization.

•Project ﬁles (*.daf) created using version 1.2 will not open properly on version 1.1.

DME Designer Owner’s Manual

Getting Started

Changes from V1.2 to V2.0

■ General

• Support added for DME8i-C/DME8o-C/DME4io-C, SP2060 units and MY16-CII.

• “Device Groups”, or groups of the same type of device, have been added at the lowest Zone level.

• It is now possible to have one master device per device group rather than one master device per zone. This means that it is possible to have multiple master devices in a single zone.

•Group masters can now be assigned regardless of the IP address. This makes it possible to have multiple device groups at a single network address.

• Conﬁgurations can be created and deleted for each device group.

■ Component

•A Feedback Suppressor component has been added. (page 398)

• The Speaker Processor component PEQ “Q” parameter now goes to “63”. (page 443)

■ Main Panel Window

• Firmware and component data can now be updated simultaneously. (page 171)

•A Recovery Update function that allows recovery from program corruption has been added. (page 173)

•A Component Link function that allows simultaneous linking of all component parameters has been added. (page 89)

• Scene Link function that allows simultaneous control of multiple devices in different device groups has been added. (page 141)

•A Protect function has been added to the scene manager. (page 79)

• Card settings are no longer included in scene data.

•A Utility window has been added to allow editing of device utility settings. (page 157)

• The Local Parameter Link display order has been changed. (page 89)

• Parameter Link operation can now be turned on or off for each device group. (page 89)

• Compilation and analysis is now possible even if no connections have been made.

• Navigator window hide/show can now be selected from the main window.

• The Event Logger can now display only the event data for a speciﬁed device. (page 72)

• The GPI terminal names have been changed from [CH] to [PORT].

DME Designer Owner’s Manual

■ Designer Window

•A hand tool for window movement has been added. The hand tool can be selected via the hand/ arrow icon in the toolbar, or from the [Tools] menu. The hand tool can also be temporarily selected by holding the spacebar on your keyboard.

• Window magniﬁcation and reduction can now be controlled via the mouse wheel while holding the keyboard “Ctrl” key.

• Horizontal scrolling can be controlled via the mouse wheel while holding the keyboard “Shift” key.

• The Edit Mode on/off can now be changed from the tool bar. (page 176)

• Scene information now appears in DME objects, and the Scene Manager can be launched from the scene information display. (page 79)

• An [On-line] button has been added to DME objects, and synchronization is now possible. (page 57)

• Sampling frequency display has been added to the resource meter window. (page 180)

Getting Started

• Sampling frequency display has been added to the conﬁguration window status bar. (page 283)

• The sampling frequency is now displayed during analysis.

• Double-clicking the component name now opens the properties window.

• Organization of the Tool Kit window has been changed. (page 182)

•A [Draw Image] checkbox that displays or hides the worksheet background image ﬁle has been added to the Sheet properties. (page 197)

• [Conﬁguration Manager] has been added to the contextual menu that appears when a DME or SP2060 object is right-clicked. (page 201,page 209)

• [Recall Component Library] and [Store Component Library] now appear in the contextual menu that appears when a component is right-clicked, even when the Edit Mode is OFF.

• The Compile Settings can now be edited for each DME unit. (page 204)

• Only one Zone window is now provided for multiple conﬁgurations.

• The [Export DXF] and [Preferences] commands have been moved from the [Print] menu to the [Tools] menu.

• [Conﬁguration] has been changed to [Conﬁguration Manager] in the [Tools] menu.

• When [Prohibit Diagonal Connections] in the [Tools] menu is active it is possible to select 2 diagonal points and those points will automatically be connected by a combination of horizontal and vertical wires.

■ Component Editor Window

•A [Level Meter Enable] command that displays or hides the meter values has been added to the contextual menu. Hiding the meters can result in increased communication speed in some cases. (page 342)

•A [Display Order] function that allows the order of the controllers to be changed as required has been added to the User Control Editor and User Module Editor. (page 307)

• An [Add Component to Component Link] command has been added to the controller contextual menu.(page 352)

• The registered group is now displayed in the [Add Parameter to Parameter Link] submenu of the contextual menu of controllers registered for Parameter Link operation.(page 350)

• Increased speed when selecting and dragging a large number of controllers in the User Control Editor and User Module Editor

• It is now possible to switch from the Navigator window to Zone display while online.

■ V2.0 Precautions

Please use DME Designer V2.0 with DME64N/24N V2.0 or higher, DME8i-C/DME8o-C/DME4io-C V2.0 or higher, and SP2060 V1.1 or higher. See the Yamaha Pro Audio website for compatibility details (http://www.yamahaproaudio.com/). When DME64N/24N and DME8i-C/DME8o-C/DME4io-C are used together in the same device group, faster communication speed as well as smoother DME Designer meter display can be obtained by assigning a DME8i-C/DME8o-C/DME4io-C unit as the device group master.

DME Designer Owner’s Manual

Getting Started

Changes from V2.0 to V3.0

■ General

• DME8i-ES/DME8o-ES/DME4io-ES support.

• The DME Designer and DME-N Network Driver installers have been combined, so the appropriate DME-N Network Driver version is now installed automatically with the DME Designer application.

• The following connections to the Slave DME units are now possible when a DME Satellite unit is assigned as the Device Group Master:

- USB/Ethernet connection to the computer (DME Designer).

- Cascade connection to control from the PM5D console (DME64N only).

■ Component

• Ambient Noise Compensator component added (page 361).

• Audio Detector component added (page 363).

• Auto Gain Control component added (page 364).

• Auto Mixer II component added (page 410).

• Simple Mixer component added (page 429).

• Room Combiner component added (page 439).

• Matrix Mixer and Router component variations added.

■ Main Panel Window

•To allow project information to be easily reproduced on a different computer, it is now possible to export and import all necessary ﬁles at once, rather than only project ﬁles with the “.daf “extension (page 42).

•A Device Information window that lists the status of all devices has been added (page 174).

• It is now possible to individually set each user control to determine whether it will open automatically when the project ﬁle is opened (page 86).

• In accordance with the above change, the Startup User Control item has been removed from the Security dialog box.

• It is now possible to assign Direct Parameter Value to the GPI input function, and assign Direct Parameter Value and Audio Detector to the GPI output function (page 106, page 116).

• An option that automatically saves the project ﬁle (.daf extension) in the DME unit when going online has been added (page 92).

• It is now possible to control internal DME-24N/DME8i-C/DME4io-C/DME8i-ES/DME4io-ES head amps from a PM5D or other compatible mixing console (page 135).

• Remote control from AMX, Crestron, and similar controllers is now possible via Ethernet connection only for DME Satellite units. (page 161).

• The display format of the parameter values displayed in the Remote Control Setup List and Parameter List dialog box can now be switched between the internal settings and the values displayed in the editor windows (page 133, page 137).

• The Event Logger window can now display additional error messages shown on the DME display panel (page 77).

• It is now possible to set the DME unit so that the internally stored event log is not erased (page 74).

• Improvements have been made to the additional error message information shown in the Event Logger window.

• The DME unit internal clock and DME Designer time display now support daylight saving time (DST) (page 167).

• Firmware updates can now be applied to entire device groups, for improved speed and efﬁciency.

DME Designer Owner’s Manual

Getting Started

■ Designer Window

• It is now possible to set a “clear” background color for text, box, and ellipse objects (page 235,

page 237, page 239).

• Password entry is now required when opening a User Module Properties dialog box or saving/ exporting in a user module to which security has been applied.

• Linked software applications can now be launched from the Slot component contextual menu (page 223).

• User module templates that use the same library are now categorized and displayed as user module groups (page 292).

• Image ﬁles are now included in User Module exports.

• Component and parameter links can now be copied when DME objects, components, and user modules are copied/pasted or duplicated.

• Parameter links are now saved when User Module data is saved/exported.

• When already-placed picture ﬁles are replaced, they will be updated and displayed correctly without the need to restart the DME Designer application.

■ Component Editor Window

• [Line] and [Scene Recall] tools have been added to the User Module Editor and User Control Editor design modes, allowing placement of lines and scene recall buttons (page 314).

• In the User Module Editor and User Control Editor it is now possible to convert placed sliders to knobs, and vice-versa (page 325).

• More options are available for customizing the controls listed below in the User Module Editor and User Control Editor:

- A property dialog box has been added for sliders, allowing customization of direction, scale,

color, size, and other parameters (page 327).

- Level meter size can be customized (page 329).

- A property dialog box has been added for slider level meters, allowing customization of

direction and size (page 330).

- Knob color and knob background color can be customized (page 326).

- Text background color can be customized (page 334).

- A property dialog box has been added for indicators, allowing customization of color and size

(page 330).

■ V3.0 Precautions

Use DME Designer V3.0 only with DME64N/24N V3.0 or higher, DME Satellite V3.0 or higher, and/or SP2060 V1.2 or higher. Refer to the Yamaha Pro Audio website (http://www.yamahaproaudio.com/) details on combinations. When combining DME64N/24N and DME Satellite units in a device group, be sure to assign a DME Satellite unit as the device group master. Synchronization cannot be performed if a DME64N/24N is assigned as the device group master. When using the Windows Vista operating system, use only USB-MIDI Driver V3.0 or higher, and DME-N Network Driver V1.2 or higher.

DME Designer Owner’s Manual

The DME Audio System Network...............................................3

The DME Designer Software Application ...................................4

Data Handled by a DME Audio System .....................................6

Chapter 1 Before Using 20

Installing DME Designer...........................................................20

Starting DME Designer.............................................................20

Closing DME Designer .............................................................22

Chapter 2 DME Designer Overview 23

Names and Functions of the Windows.....................................23

Users and Security ...................................................................28

Files Used by the DME DESIGNER.........................................31

Configuration Creation Procedure............................................46

Online .......................................................................................47

Chapter 3 Main Panel Window 52

Names and Functions of the Windows.....................................52

Main Panel Window Menu........................................................58

DME File Storage .....................................................................68

Preferences ..............................................................................69

Event Logger ............................................................................72

Scene Manager ........................................................................79

User Control .............................................................................86

Parameter Link .........................................................................89

Synchronization

(DME Designer and Unit Synchronization)...............................91

Event Scheduler .......................................................................95

Wav File Manager ..................................................................102

GPI .........................................................................................106

MIDI........................................................................................119

User Defined Button (User Defined Parameters) ...................126

DAW Control ..........................................................................130

Remote Control Setup List .....................................................133

Internal HA Control.................................................................135

Parameter List ........................................................................137

Component Lock ....................................................................140

Scene Link Manager ..............................................................141

SP2060 Library Manager .......................................................143

MIDI Port Setup......................................................................145

Shortcut Keys .........................................................................146

Security (Creating Users and Making User Settings).............147

Network Setup........................................................................155

Utility.......................................................................................157

Word Clock.............................................................................164

Monitor Out.............................................................................166

Clock ......................................................................................167

Language Settings .................................................................169

Backup ...................................................................................170

DME Firmware Update...........................................................171

Device Information .................................................................174

Chapter 4 Designer 176

Editing Configurations ............................................................176

Designer Window ...................................................................177

Toolkit Window .......................................................................182

Designer Window Menu .........................................................187

Objects ...................................................................................194

Design Window Shared Settings and Operations ..................251

Drawing and Editing Wires .....................................................262

Adding, Deleting, and Renaming a Zone ...............................273

Changing Device Groups .......................................................275

Adding, Deleting, and Renaming a Configuration ..................277

Area Window ..........................................................................279

Zone Window .........................................................................280

Configuration Window ............................................................283

User Module ...........................................................................291

Chapter 5 Editor Window 301

Component Editor Window.....................................................301

User Control Editor/User Module Editor .................................307

Operation Mode and Design Mode ........................................340

Context Menu .........................................................................341

Snap .......................................................................................344

Library ....................................................................................346

Creating Parameter Links.......................................................350

Creating Component Links.....................................................352

Chapter 6 Component Guide 353

Types of Components ............................................................353

Ambient Noise Compensator .................................................361

Audio Detector........................................................................363

Auto Gain Control...................................................................364

Crossover ...............................................................................365

Crossover Processor..............................................................369

Delay ......................................................................................381

Dynamics................................................................................383

Equalizer (EQ)........................................................................393

Fader ......................................................................................397

Feedback Suppressor ............................................................398

Filters......................................................................................399

Meter ......................................................................................407

Miscellaneous.........................................................................408

Mixer.......................................................................................410

Pan .........................................................................................432

Room Combiner .....................................................................439

Router.....................................................................................440

Source Selector......................................................................442

Speaker Processor.................................................................443

SPX ........................................................................................450

Slot .........................................................................................461

Cascade .................................................................................463

Analog Input and Output ........................................................465

SP2060 Input and Output.......................................................466

CobraNet Input and Output ....................................................467

EtherSound Input and Output.................................................469

MY-Card .................................................................................470

Remote Controlled Head Amp ...............................................474

Component Glossary..............................................................476

Appendix 480

Options ...................................................................................480

Main Display...........................................................................482

Parameter Edit Displays.........................................................483

Utility Displays ........................................................................487

DME Designer Owner’s Manual

Troubleshooting 492

Index 493

Getting Started

DME Designer Owner’s Manual

Chapter 1 Before Using

Installing DME Designer

To use DME Designer, you must ﬁrst install the software on the computer. Before you can connect the DME Designer software to the DME or SP2060 unit, you must ﬁrst install the USB MIDI Driver or the DME-N Network Driver, according to how you will be connecting, and then make the appropriate settings. For instructions about the installation and setup for the DME Designer and DME-N Network Driver, and about the installation for the USB-MIDI Driver, see the "DME Setup Manual."

NOTE

Initial settings for DME Satellite units must be transferred via USB-MIDI, so it is necessary to properly install the USB-MIDI Driver.

Starting DME Designer

The DME Designer software is started from the [Start] menu. DME Designer is used with one user logged on. The user logs on when the software is started.

■ DME Designer Start Up and Logon (When Auto-Logon Is Not Set)

1 Click [Start] ➞ [All Programs] ➞ [YAMAHA OPT Tools] ➞ [DME Designer] ➞ [DME

Designer].

NOTE

In Windows2000, click [Start] → [Programs] → [YAMAHA OPT Tools] → [DME Designer] → [DME Designer].

The “Log On” dialog box will be displayed.

NOTE

Automatic log-on is the default setting. If the automatic logon feature is enabled, the “Log On” dialog box will not be displayed when the application is started. Instead, the auto-logon user will be logged on automatically. See page 30 for information about auto-logon.

DME Designer Owner’s Manual

Chapter 1 Before Using

2 Click the [▼] at the right of the [User] box, and select the user.

If no user has been created, only [Administrator] will appear in the list. When starting DME Designer for the ﬁrst time after installing, select [Administrator].

3 Enter the password into the [Password] box.

Enter the password set for the user. If no password has been set, leave the password box blank when you log on.

4 Click the [OK] button.

DME Designer starts up.

■ When Automatic Logon Has Been Set (page 30)

If automatic logon has been set, the “Log On” dialog box will not be displayed. The user set for automatic logon will be logged on. With automatic log on, even if a password is set for a user, it will not be requested during log on. This is useful when logging on a speciﬁc user.

■ Starting by Opening a Project File

DME Designer starts when a project ﬁle with a saved conﬁguration is opened. When the project ﬁle is opened, DME Designer is started with the window conﬁguration that was in place when the ﬁle was last saved.

DME Designer Owner’s Manual

Chapter 1 Before Using

Closing DME Designer

To close DME Designer, click [Exit] on the [File] menu of the Main Panel window. It can also be closed by clicking the [Close] button on the Main Panel window.

1 Click [Exit] on the Main Panel window [File] menu.

When you try to close DME Designer, “Project File has been modiﬁed. Save?” will be displayed in a dialog box.

NOTE

Sometimes the “Project File has been modiﬁed. Save?” dialog box will not be displayed.

2 To save the ﬁle, click [Yes]. To close without saving, click [No].

If you click [Yes], the File Save dialog box will be displayed.

DME Designer Owner’s Manual

Chapter 2 DME Designer Overview

Names and Functions of the Windows

The DME Designer software has several windows, including the Main Panel window, Designer window, Component Editor window, Resource Meter window, and others.

Main Panel Window

Designer Window

Component Editor Window

Resource Meter Window

Main Panel Window

Menus and buttons are available in the Main Panel window. The current DME Designer environment, including the active zone, device group and scene the currently logged on user name, and the connection status to the DME unit are displayed on the right side of the Main Panel window.

DME Designer Owner’s Manual

Chapter 2 DME Designer Overview

Designer Window

The Designer window displays several different windows. First among them is the Area window, where you can manage the entire system. The Area window includes one or more Zone windows, which in turn include one or more DME or SP2060 units that are used to build a zones within the area. Next is the Conﬁguration window, where you create the internal conﬁguration of each DME or SP2060 unit. Within the Conﬁguration window are the User Module windows, where you can assemble often-used components into templates the Toolkit window, which displays objects used in the other windows as the basic building blocks for sound designs; and the Navigator window, which lets you grasp the overall status of the system at a glance.

Toolkit Window

Conﬁguration Window

User Module Window

Navigator WindowZone Window

■ Area Window

The Area window is used for designing areas, which manage the entire system. While at least one zone is included within an area, multiple zones can be arranged there.

DME Designer Owner’s Manual

Zones

Chapter 2 DME Designer Overview

■ Zone Window

The Zone window is used to design zones within the area. A zone is a more concrete blueprint that includes at least one DME or SP2060. It shows the DME’s connections with other devices and the wiring between them. You can create multiple zones. The DME and SP2060 units and connected devices are arranged in each Zone window, creating conﬁgurations.

Conﬁgurations

■ Conﬁguration Window

The Conﬁguration window is used to design the internal conﬁguration of each DME unit contained in the Zone window. By arranging and connecting components in the Conﬁguration window, you can create things like complex processors or matrix mixers, that determine the actual internal structure that operates each DME unit.

Components

■ User Module Window

The User Module window is used for designing user modules that can be arranged in the Conﬁguration window. You can create original modules by combining multiple examples of oftenused components. When you save these modules as templates you can recall them easily whenever you want.

DME Designer Owner’s Manual

Chapter 2 DME Designer Overview

■ Toolkit Window

The Toolkit window displays the objects that you can use in each window that can be displayed in the Designer window. Those windows are the Area, Zone, Conﬁguration, and User Module windows. The Toolkit displays different objects, according to the currently active window. To place an object in a window, double-click it in the Toolkit window where it is displayed or drag it to the currently active window.

■ Navigator Window

The Navigator window displays the area, zones, conﬁgurations, and components in a hierarchal fashion that lets you check their status as a whole. When editing ofﬂine, you can click an area name, zone name, or conﬁguration name to make that window active. Clicking a component name will open the component editor window for that component.

■ Resource Meter Window

This window provides an indication of component usage for each DME unit currently placed in the Conﬁguration window. The usage percentage increases as the number of components increases. The component usage percentage is shown in graph form for each DME unit. The window appears simultaneously with the designer window, and can be used as a component usage guide while creating conﬁgurations. The sampling frequency for each DME unit is also displayed. Please note that the sampling frequency of the DME unit itself will also affect the usage percentage.

NOTE

This window is not displayed for SP2060 units.

■ Objects and Components

“Object” is the name for the parts that are arranged in the various design windows, such as the Area, Zone, Conﬁguration, and User Module windows. Objects are always laid out in the Toolkit window. Only the appropriate objects for each window are displayed. The blocks displayed at the higher level of the Toolkit window in particular are called “components.” This refers to each type of processor that operates the DME. “Object” normally refers to Picture, Text, Ellipse and other items that are used after connecting them by wire to the various components.

DME Designer Owner’s Manual

Chapter 2 DME Designer Overview

Component Editor

The blocks that are arranged in the conﬁguration window are called “components.” When you double-click on a component block arranged in the Conﬁguration window, the Component Editor window will open. There you can edit the parameters for that component. The types of parameters displayed will differ, depending on the component.

Component Editor

(Stereo Compressor)

Component

Window Operations

Operations in all windows are the same as for normal Windows applications. The windows are controlled with the [Minimize], [Maximize/Restore], and [Close] buttons at the upper right of the title bar. DME Designer is closed by clicking the [Close] button on the Main Panel window.

DME Designer Owner’s Manual

Chapter 2 DME Designer Overview

Users and Security

You can create multiple users in DME Designer and set the functions that are available to each user. Although users who will design and put together installations must be able to use all the functions of DME Designer, users who will only operate the system can be restricted to functions that will not allow them to accidentally change the settings. DME Designer is used with one user at a time logged on. To change the user, click the [File] menu → [Log Off] command on the Main Panel window.

About Users

To use DME Designer, you must logon when you start the software. Except for the ﬁrst time the software is started or when separate settings are made for the ﬁrst time, you can logon by specifying the name and password for a user that has been set as the administrator. The administrator can build the system as a whole, or apply function limitations that let other people edit. Administrators or other people that can use DME Designer are called “users.” The user name for the currently logged on user appears below [User] on the Main Panel window.

Currently Logged On User Name

The default user, named [Administrator], is set to use all of the functions. Immediately after DME Designer is installed, [Administrator] is the only user, and there is no password set. Multiple users can be created. When the system administrator creates multiple users, restrictions can be applied separately for each one of them. A user with restrictions applied can edit using only the functions the administrator enables for him. The place to create, setup, and delete users is the “Security” dialog box. See “Scene Manager” on

page 79.

DME Designer Owner’s Manual

Chapter 2 DME Designer Overview

Logging On

The “Log On” dialog box is displayed whenever the application is started or a user is logged off. Whenever one user is already logged on, another user cannot be logged on. To log on as another user, ﬁrst log off the currently logged on user.

NOTE

If the automatic logon feature is enabled, the “Log On” dialog box will not be displayed when the application is started. Instead, the auto-logon user will be logged on automatically.

■ The “Log On” dialog box

1 [User]

From the list, select the user you want to log on as.

2 [Password] Box

Enter the password.

3 [OK] Button

Log on as the selected user.

4 [Exit] Button

When the application is started, and the “Log On” dialog box is displayed, there is an [Exit] button. This closes the application without logging on a user.

5 [Cancel] Button

When the “Log On” dialog box is displayed after a user is logged off, there is a [Cancel] button instead of an [Exit] button. This cancels the logoff. The original user will continue to be logged on.

■ Logon Procedure

1 Click [▼] at the right of the [User].

A drop-down list of user names will be displayed.

2 Click the user you want to log on.

3 Enter the password into the [Password] box.

When you type in the password box, the characters you enter will display as asterisks (*).

4 Click the [OK] button.

DME Designer Owner’s Manual

Chapter 2 DME Designer Overview

Logging Off

Logoff is used when changing users. When you log off, the document currently being edited is closed, and the “Log On” dialog box is displayed so you can log on the next user. Log off with the [Log Off] command on the [File] menu in the Main Panel window.

1 Click the [File] menu ➞ [Log Off] command on the Main Panel window.

Log on the next user in the “Log On” dialog box.

Automatic Logging On

With the auto-logon function, you can have a speciﬁed user automatically logged on when the application is started. If you enable the auto-logon feature, the speciﬁed user will be logged on when the application is started, without displaying the “Log On” dialog box. Auto-logon is set from the “Security” dialog box. See “Scene Manager” on page 79.

DME Designer Owner’s Manual

+ 467 hidden pages

Yamaha DME DESIGNER V3.0 Manual

The DME Audio System Network

The DME Designer Software Application

Data Handled by a DME Audio System

Contents

Chapter 1 Before Using

Installing DME Designer

Starting DME Designer

Closing DME Designer

Chapter 2 DME Designer Overview

Names and Functions of the Windows

Users and Security