Yamaha DD-55 User Manual
Owner’s Manual
Owner’s Manual
SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power supply (adapter). DO NOT
connect this product to any power supply or adapter other than one described
in the manual, on the name plate, or specifically recommended by Yamaha.
This product should be used only with the components supplied or; a cart,
rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please
observe all safety markings and instructions that accompany the accessory
product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to be correct at the time
of printing. However, Yamaha reserves the right to change or modify any of
the specifications without notice or obligation to update existing units.
This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that could
cause permanent hearing loss. DO NOT operate for long periods of time at a
high volume level or at a level that is uncomfortable. If you experience any
hearing loss or ringing in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period before damage occurs.
NOTICE:
Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered
by the manufacturer’s warranty, and are therefore the owners responsibility.
Please study this manual carefully and consult your dealer before requesting
service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with both the letter
and the spirit of the law, we want you to be aware of the following:
Battery Notice:
This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is
approximately five years. When replacement becomes necessary, contact a
qualified service representative to perform the replacement.
This product may also use “household” type batteries. Some of these may be
rechargeable. Make sure that the battery being charged is a rechargeable
type and that the charger is intended for the battery being charged.
When installing batteries, do not mix batteries with new, or with batteries of a
different type. Batteries MUST be installed correctly. Mismatches or incorrect
installation may result in overheating and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all batteries
away from children. Dispose of used batteries promptly and as regulated by
the laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair, or for some reason its
useful life is considered to be at an end, please observe all local, state, and
federal regulations that relate to the disposal of products that contain lead,
batteries, plastics, etc. If your dealer is unable to assist you, please contact
Yamaha directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the product. The model number,
serial number, power requirements, etc., are located on this plate. You should
record the model number, serial number, and the date of purchase in the
spaces provided below and retain this manual as a permanent record of your
purchase.
Model
Serial No.
Purchase Date
92-BP (bottom)
PLEASE KEEP THIS MANUAL
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in
this manual, meets FCC requirements. Modifications not expressly
approved by Yamaha may void your authority, granted by the FCC, to use
the product.
2. IMPORTANT: When connecting this product to accessories and/or
another product use only high quality shielded cables. Cable/s supplied
with this product MUST be used. Follow all installation instructions. Failure
to follow instructions could void your FCC authorization to use this product
in the USA.
3. NOTE: This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reasonable level
of assurance that your use of this product in a residential environment will
not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used
according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
OBSERVERA!
Apparaten kopplas inte ur växelströmskällan (nätet) sá länge som den ar
ansluten till vägguttaget, även om själva apparaten har stängts av.
ADVARSEL: Netspæendingen til dette apparat er IKKE afbrudt, sálæenge
netledningen siddr i en stikkontakt, som er t endt — ogsá selvom der or
slukket pá apparatets afbryder.
VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta
verkosta.
with FCC regulations does not guarantee that interference will not occur in
all installations. If this product is found to be the source of interference,
which can be determined by turning the unit “OFF” and “ON”, please try to
eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the
interference.
Utilize power outlets that are on different branch (circuit breaker or fuse)
circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the
antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial
type cable.
If these corrective measures do not produce satisfactory results, please
contact the local retailer authorized to distribute this type of product. If you
can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave,
Buena Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
(class B)
Entsorgung leerer Batterien (nur innerhalb Deutschlands)
Leisten Sie einen Beitrag zum Umweltschutz. Verbrauchte Batterien oder
Akkumulatoren dürfen nicht in den Hausmüll. Sie können bei einer Sammelstelle für Altbatterien bzw. Sondermüll abgegeben werden. Informieren
Sie sich bei Ihrer Kommune.
(battery)
(standby)
2
PRECAUTIONS
Yamaha cannot be held responsible for damage caused by improper
use or modifications to the instrument, or data that is lost or destroyed.
* The illustrations and LED displays as shown in this owner’s manual
are for instructional purposes only, and may be different from the
ones on your instrument.
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep these precautions in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,
short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
• Do not open the instrument or attempt to disassemble the internal parts or
modify them in any way. The instrument contains no user-serviceable
parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel.
• Do not expose the instrument to rain, use it near water or in damp or wet
conditions, or place containers on it containing liquids which might spill
into any openings.
• If the AC adaptor cord or plug becomes frayed or damaged, or if there is a
sudden loss of sound during use of the instrument, or if any unusual
smells or smoke should appear to be caused by it, immediately turn off the
power switch, disconnect the adaptor plug from the outlet, and have the
instrument inspected by qualified Yamaha service personnel.
• Use the specified adaptor (PA-5C or an equivalent recommended by
Yamaha) only. Using the wrong adaptor can result in damage to the instrument or overheating.
• Before cleaning the instrument, always remove the electric plug from the
outlet. Never insert or remove an electric plug with wet hands.
• Check the electric plug periodically and remove any dirt or dust which may
have accumulated on it.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the
instrument or other property. These precautions include, but are not limited to, the following:
• Do not place the AC adaptor cord near heat sources such as heaters or
radiators, and do not excessively bend or otherwise damage the cord,
place heavy objects on it, or place it in a position where anyone could walk
on, trip over, or roll anything over it.
• When removing the electric plug from the instrument or an outlet, always
hold the plug itself and not the cord.
• Do not connect the instrument to an electrical outlet using a multiple-connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet.
• Unplug the AC power adaptor when not using the instrument, or during
electrical storms.
• Always make sure all batteries are inserted in conformity with the +/polarity markings. Failure to do so might result in overheating, fire, or battery fluid leakage.
• Always replace all batteries at the same time. Do not use new batteries
together with old ones. Also, do not mix battery types, such as alkaline batteries with manganese batteries, or batteries from different makers, or different types of batteries from the same maker, since this can cause
overheating, fire, or battery fluid leakage.
• Do not dispose of batteries in fire.
• Do not attempt to recharge batteries that are not intended to be charged.
• When the batteries run out, or if the instrument is not to be used for a long
time, remove the batteries from the instrument to prevent possible leakage
of the battery fluid.
• Keep batteries away from children.
• If the batteries do leak, avoid contact with the leaked fluid. If the battery
fluid should come in contact with your eyes, mouth, or skin, wash immediately with water and consult a doctor. Battery fluid is corrosive and may
possibly cause loss of sight or chemical burns.
• Before connecting the instrument to other electronic components, turn off
the power for all components. Before turning the power on or off for all
components, set all volume levels to minimum. Also, be sure to set the
volumes of all components at their minimum levels and gradually raise the
volume controls while playing the instrument to set the desired listening
level.
• Do not expose the instrument to excessive dust or vibrations, or extreme
cold or heat (such as in direct sunlight, near a heater, or in a car during the
day) to prevent the possibility of panel disfiguration or damage to the internal components.
• Do not use the instrument near other electrical products such as televisions, radios, or speakers, since this might cause interference which can
affect proper operation of the other products.
• Do not place the instrument in an unstable position where it might accidentally fall over.
• Before moving the instrument, remove all connected adaptor and other
cables.
• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.
Also, do not place vinyl, plastic or rubber objects on the instrument, since
this might discolor the panel or keyboard.
• Do not rest your weight on, or place heavy objects on the instrument, and
do not use excessive force on the buttons, switches or connectors.
• Do not operate the instrument for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you
experience any hearing loss or ringing in the ears, consult a physician.
■DATA BACK-UP AND STORAGE
• Yamaha recommends that you regularly save data using an external device
such as the floppy disk-based Yamaha MIDI data filer MDF3, and storing
the floppy disks in a safe, cool, dry place. YAMAHA CANNOT BE HELD
RESPONSIBLE FOR THE ACCIDENTAL LOSS OF IMPORTANT MUSIC
DATA! Regarding the data you have created, as long as fresh batteries are
inserted in (or an AC power adaptor is connected to) the instrument, the
data will be retained, even when the power is turned off. It will also be
retained long enough to exchange an old set of batteries for a new set. If
you have important data in the instrument which you don’t want to lose,
please take care to keep fresh batteries inserted in (or keep an AC power
adaptor connected to) the instrument, and to regularly save data.
Always turn the power off when the instrument is not in use.
Make sure to discard used batteries according to local regulations.
(4)-7
3
Congratulations!
Thank you for purchasing the Yamaha DD-55. The DD-55 has been developed
to respond and play like a drum set - but with greater ease, flexibility and
sophisticated functions. Before you use the instrument, we recommend that you
carefully read through this manual.
Contents
Setting Up 5
Power Requirements .............................................5
Panel Controls 6
Playing the Demo Song 8
Play the Pads/Pedals 9
Pad Names ............................................................9
Hand Percussion ON/OFF ...................................10
Assigning a Drum Kit to the Pads and Pedals .....10
Assigning a Voice to Individual Pads and Pedals
(“CU” Custom Kit)............................................11
Reverb ON/OFF...................................................12
Setting the Pad Sensitivity ...................................13
Adjusting the Pad Volume....................................14
Click ON/OFF.......................................................14
Playing a Song 15
Select the Song and Play.....................................15
Tap Start ..............................................................16
Auto Kit Select ON/OFF Setting...........................16
Adjusting the Tempo ............................................17
Play along with a Song 18
Track ON/OFF .....................................................18
Break....................................................................18
A-B Repeat ..........................................................19
Recording a Song 20
Recording............................................................ 20
Playback.............................................................. 20
MIDI Functions 21
What’s MIDI?....................................................... 21
What You Can Do With MIDI .............................. 23
Connecting to a Computer .................................. 24
Enter/Exit the MIDI/Utility Mode .......................... 25
Setting the Clock ................................................. 25
Local ON/OFF ..................................................... 26
Setting the MIDI Transmit Channel ..................... 27
Setting the MIDI Note Number ............................ 28
Saving and Loading Song Data .......................... 29
Appendix 31
Initialize ............................................................... 31
Troubleshooting .................................................. 32
Drum Voice List................................................... 33
Song List ............................................................. 35
Drum Kit List........................................................ 36
Drum Map ........................................................... 38
GM Voice List...................................................... 40
MIDI Implementation Chart ................................. 41
Specifications ...................................................... 44
● Trademarks
• Apple and Macintosh are trademarks of Apple Computer, Inc., registered in the U.S. and
other countries.
• Windows is the registered trademark of Microsoft
All other trademarks are the property of their respective holders.
®
Corporation.
4
● Supplied Accesoories
• Drum Stick (x2)
• Foot Pedal 1 & 2
• Owner’s Manual
Setting Up
This section contains information about setting up your DD-55 for playing. Make sure
to read this section carefully before using the instrument.
Power Requirements
Although the DD-55 will run either from an optional AC adaptor or batteries, Yamaha recommends
use of an AC adaptor whenever possible. An AC adaptor is more environmentally friendly than batteries and does not deplete resources.
Using an AC Power Adaptor
q Make sure that the [STANDBY/ON] switch of the DD-55
is set to STANDBY.
w Connect the AC adaptor (PA-5C or other adaptor specifi-
cally recommended by Yamaha) to the power supply jack.
e Plug the AC adaptor into an AC outlet.
• Never interrupt the power supply (e.g. remove the batteries or
unplug the AC adaptor) during any DD-55 record operation!
Doing so can result in a loss of data.
• Use ONLY a Yamaha PA-5C AC Power Adaptor (or other adaptor specifically recommended by Yamaha) to power your
instrument from the AC mains. The use of other adaptors may
result in irreparable damage to both the adaptor and the DD-
55.
• Unplug the AC Power Adaptor when not using the DD-55, or
during electrical storms.
Using Batteries
For battery operation the DD-55 requires six 1.5V “C” size,
R14P (LR14) or equivalent batteries. (Alkaline batteries are
recommended.) When the batteries need to be replaced, the
volume may be reduced, the sound may be distorted, and other
problems may occur. When this happens, turn the power off
and replace the batteries, as described below.
q Open the battery compartment cover located on the instru-
ment’s bottom panel.
w Insert the six new batteries, being careful to follow the
polarity markings on the inside of the compartment.
e Replace the compartment cover, making sure that it locks
firmly in place.
PA-5C
• When the batteries run down, replace them with a complete set of six new batteries.
NEVER mix old and new batteries.
• Do not use different kinds of batteries (e.g. alkaline and manganese) at the same
time.
• If the instrument is not to be in use for a long time, remove the batteries from it, in
order to prevent possible fluid leakage from the battery.
• Plugging or unplugging the AC power adaptor while the batteries are installed will
reset the DD-55 to the defaults.
5
Panel Controls
Front Panel
!8
888
Pedal 2 Pedal 1
q
w
!5
!4
!2
!3
Front Panel
q DEMO button ......................................... 8, 25
w CLICK button ............................................. 14
e DISPLAY .....................................................10
r VOLUME [▲], [▼] buttons........................... 8
t HAND PERC button................................... 10
y DRUM 1 - 3 buttons ................................... 18
u BACKING button........................................ 18
i PAD button.....................................11, 14, 27
o KIT button ............................................ 10, 28
e
888
y ut
oi !0 !1
!6
!0 SONG button ............................. 8, 15, 16, 17
!1 TEMPO button........................................... 17
!2 START/STOP button........................ 8, 15, 25
!3 A-B REPEAT button .................................. 19
!4 BREAK/TAP button ............................. 16, 18
!5 REC button ................................................ 20
!6 STANDBY/ON Switch ............................ 8, 31
!7 DIAL............................................................ 10
!8 Drum Pads (x7)............................................ 9
r
!7
6
Panel Controls
Using the Foot Pedals (1/2)
When connected, these pedals can be used simultaneously play the drum set’s hi-hat pedal or bass
drum voices — or they can also be assigned to
play other voices as well. Connect the supplied
Pedal 1 to the PEDAL 1 jack @4 and Pedal 2 to
the PEDAL 2 jack @1.
• Make sure that the pedal plugs are properly connected to the PEDAL jacks before turning on the
power.
• Do not press Pedal 2 while turning the power on.
Doing this changes the recognized polarity of the
pedal, resulting in reversed pedal operation.
• Avoid using the pedals directly on a soft floor,
since they may scratch the surface of the floor.
Using a pair of headphones
A standard pair of stereo headphones can be
plugged in here for private practice or late-night
playing. The internal stereo speaker system is
automatically shut off when a pair of head phones
is plugged into the PHONES/OUTPUT jack.
Do not listen with the headphones at high volume for long periods of time. Doing so may cause hearing loss.
Side Panel (Left)
Side Panel (Right)
@3
@4
@2
• Connect the DD-55 to external equipment only after turning off
power for all devices. To prevent damage to the speakers, set the
volume of the external devices at the minimum setting before connecting them. Failure to observe these cautions may result in electric shock or equipment damage.
!9
@0
@1
• Since speakers are built into the
DD-55, you should be careful to
never leave any video tapes,
cassette tapes, floppy disks or
any kind of magnetic storage
media on the panel — doing so
may result in data loss or damage to the items. Also avoid
using the DD-55 near a television or computer monitor, since
interference may result.
Side Panel (Left)
!9 DC IN 12V (AC Adaptor) Jack..................... 5
@0 PHONES/OUTPUT Jack .............................. 7
@1 PEDAL 2 Jack .............................................. 7
Side Panel (Right)
@2 MIDI IN Terminal......................................... 22
@3 MIDI OUT Terminal..................................... 22
@4 PEDAL 1 Jack .............................................. 7
7
Playing the Demo Song
The DD-55 features a demonstration song, specially created to show you the dynamic
possibilities of the instrument.
1 Turn on the power.
Turn the [STANDBY/ON] switch ON.
• Even when the switch is in the “STANDBY” position, electricity is still flowing to the instrument at the minimum level. When you are not using the DD55 for a long time, make sure you unplug the AC power adaptor from the
wall AC outlet, and/or remove the batteries from the instrument.
2 Start the Demo Song.
Press the [DEMO] button and the demo song starts playing.
● MASTER VOLUME
The overall volume level of the DD-55 is controlled by two VOLUME
[▲], [▼] buttons (10 volume levels L0 - L9).
Large
Small
Press the VOLUME [▲] button to increase the overall volume by one
level. Press the VOLUME [▼] button to decrease the overall volume
by one level. Holding down either of the buttons increases or decreases
the volume level rapidly.
L0 ← L5 → L9
Small ← Volume Level → Large
* When the VOLUME is set to L0, no sound is produced.
3 Stop the Demo Song.
To stop playback, press the [DEMO] button again or press the
[START/STOP] button.
● SONG VOLUME
To control the volume level of the song, press the
song starts playing, simultaneously hold down the
the
VOLUME [▲], [▼]
(For more information on songs, see page 15.)
The SONG VOLUME can be used to adjust the balance between the
song accompaniment and your own performance on the pads.
buttons (levels L0 - L9).
[SONG]
[SONG]
button and the
button and use
Simultaneously hold down the
[▲]
button to increase the song volume by one level. Hold down the
[SONG]
volume by one level. Holding either of the buttons (while holding down the
[SONG]
button and press the
button) increases or decreases the song volume level rapidly.
L0 ← L5 → L9
Small ← Volume Level → Large
* When the VOLUME is set to L0, no sound is produced by the song.
[SONG]
VOLUME [▼]
button and press the
VOLUME
button to decrease the song
8
Play the Pads/Pedals
Strike the pad with the supplied drum sticks or your hands to play the drum voices.
When playing the pads with your hands, turn the Hand Percussion feature on by pressing the [HAND PERC] button (the lamp lights).
The volume of the pads’ sounds responds to your playing; when you play soft the volume is soft, and when you play strongly the volume is loud.
The actual loudness of the sound may vary according to which part of the pad is
struck.
Pad Names
A hi-hat sound is assigned to Small Pad 3 (Drum Kit
00). Striking Small Pad 3 while pressing Pedal 2 produces a closed hi-hat sound.
Striking the pad without pressing the pedal produces
an open hi-hat sound.
Small Pad 1
107: Crash
Cymbal 2
Pad 2
061: Mid Tom (High)
Pad 1
053: Open Rim Shot
Pad 3
063: Low Tom
Small Pad 3
102: Hi-Hat
Closed/Open
Ex. shown, Drum Kit 00
Small Pad 2
110: Ride
Cymbal 1
Pad 4
065: Floor Tom (Low)
Pedal 2
102: Hi-Hat Pedal
The bass drum voice is controlled by
pressing Foot Pedal 1.
Pedal 1 features touch response; the
volume responds to how hard you
press the pedal.
Use Foot Pedal 2 to control the Hi-hat.
(This is in the case of Drum Kit 00.)
Pedal 1
001: Bass Drum (Hard)
9
Play the Pads/Pedals
Hand Percussion ON/OFF
You can play the pads of the DD-55 either with the supplied sticks or with your hands.
1 Press the [HAND PERC] button.
Hand Percussion on
When you press the [HAND PERC] button, the button’s lamp lights,
and the pad sensitivity is automatically adjusted for optimum playing
by hand.
• When HAND PERCUSSION is on, the DD-55 automatically selects an
appropriate song (#94) and kit (#29), ideal for playing by hand and using
with the Hand Percussion feature.
• When Hand Percussion is on, do not strike the pads with drumsticks or
anything other than your hands.
Assigning a Drum Kit to the Pads and Pedals
The DD-55 allows you to choose from 45 different Drum Kits (00 - 44 : see the “Drum Kit List”
page 36) quickly and easily. 45 of the kits have preset voice combinations that will be set to the pads
and pedals when the kit is selected.
Select some different kits and try playing them.
The DD-55 also has one Custom Drum Kit allowing you to assign the desired voices to the seven
pads or two pedals (see “Assigning a Voice to Individual Pads and Pedals” page 11).
For some drum kits (35 - 44), the sound changes each time you strike the pad.
10
00 CU01 44
00
1 Press the [KIT] button.
When you press the [KIT] button, the currently selected Drum Kit
number appears on the display.
2 Select a Drum Kit Number.
Turn the DIAL to select a Drum Kit number. Drum Kit numbers will
increase as the DIAL is turned to the right (clockwise), and decrease
as the DIAL is turned to the left (counter-clockwise).
• Drum Kit number 00 is normally selected when the power is turned on.
However, if Auto Kit Select is set to OFF, the last Drum Kit selected before
turning the power OFF, is automatically selected when the power is turned
on. (See “Auto Kit Select ON/OFF Setting ” on page 16.)
• The “ CU” Drum Kit is the Custom Kit. Changes made to any one of the
preset drum kits will be saved here. (See “Assigning a Voice to Individual
Pads and Pedals” page 11.)
Play the Pads/Pedals
Assigning a Voice to Individual Pads and Pedals (“CU” Custom Kit)
The DD-55 contains a total of 212 high quality drum sounds (see the “Drum Voice List” page 33) —
and you can assign these freely to each of the 7 drum pads and 2 foot pedals. Try assigning some different voices and create your own “CU” Custom Drum Kit.
• Any changes made to one of the preset drum kits will automatically be saved in
the “ CU” Custom Drum Kit.
• Both the Custom and “00” drum kit contents are the same until modified (see
the “Drum Kit List” page 36).
1 Press the [PAD] button.
When you press the [PAD] button, Pad 1’s currently assigned voice
008
number is shown in the display.
020
000 211001 210
2 Select the pad or pedal to be assigned.
Strike any pad one time (or press a pedal), and the currently assigned
voice number for that pad/pedal is shown in the display.
3 Select a Voice Number.
You can select the voice by repeatedly striking the pad or repeatedly
pressing the pedal (while listening to the voice), or by turning the
DIAL.
● Striking the pad or pressing the pedal to select a voice.
Every time the pad is struck or a pedal is pressed, voice numbers will
increase by a value of one (1).
● Using the DIAL to select a voice.
Turn the DIAL to the right (clockwise), and voice numbers will
increase. Turn the DIAL to the left (counter-clockwise), and voice
numbers will decrease.
000 211001 210
CU
Repeat the previous steps 2 and 3 for any or all of the DD-55’s pads
and pedals.
4 Play the Pads and Pedals.
After assigning a voice to the desired pad/pedal, press the [KIT] button. You can now play the voice you have assigned to the pad/pedal.
After you’ve assigned the voice, the DD-55 will automatically be set to
the custom kit.
11
Play the Pads/Pedals
Reverb ON/OFF
Different depths of the DD-55’s reverb effect can be added to the DD-55’s overall sound.
1 Display the Reverb On/Off Setting.
Simultaneously press the [DEMO] and [START/STOP] button to
enter the MIDI/Utility mode, then press the [DRUM3] button. The
current Reverb setting appears in the display.
on
Reverb on
2 Set the Reverb On/Off.
To set to “on” (Reverb ON), turn the DIAL to the right (clockwise), to
set to “oFF” (Reverb OFF), turn the DIAL to the left (counter-clockwise).
onoFF
3 Exit the Reverb On/Off Setting.
After setting the Reverb ON/OFF, simultaneously press the [DEMO]
and [START/STOP] button to exit the MIDI/Utility mode.
12
Play the Pads/Pedals
Setting the Pad Sensitivity
The DD-55 allows you to custom-set the sensitivity of the pads (range 0 - 2).
When set to a value of 2, the pad sensitivity is the highest, providing the most dynamic range for
your playing (softest to loudest volume).
1 Display the current pad sensitivity setting.
Simultaneously press the [DEMO] and [START/STOP] button to
enter the MIDI/Utility mode, then press the [HAND PERC] button.
The current pad sensitivity setting appears in the display.
1
2 Set the sensitivity value.
To raise the value, turn the DIAL to the right (clockwise), and to lower
it, turn the DIAL to the left (counter-clockwise).
3 Exit the sensitivity setting.
021
Adjusting the Pad’s Sensitivity
The factory default setting for pad sensitivity should provide you with trouble-free use. However, it is possible to adjust the pad’s sensitivity (0 - 2, factory default = 1) if you are experiencing one of the problems
shown below.
● Striking two pads simultaneously results in one of the pads not sounding.
→Set the pad sensitivity level to 2. When two pads are simultaneously struck with this set-
ting, both pads will sound together.
However, if you strike a pad with too much force, you may inadvertently trigger the sound
of another pad.
After setting the sensitivity, simultaneously press the [DEMO] and
[START/STOP] button to exit the MIDI/Utility mode.
• Default setting is “1.”
● Striking a pad results in other pads also sounding, though they were not
struck.
→Set the pad sensitivity level to 0. With this setting, pads that are not struck will become
harder to sound.
However, if you strike two pads simultaneously without enough force, one of the struck
pads may not sound.
13
Play the Pads/Pedals
Adjusting the Pad Volume
The DD-55 lets you adjust the volume of each pad (range: L0 - L9), allowing you to set the overall
balance of the kit.
1 Press and hold the [PAD] button and strike the
pad whose volume you want to adjust.
The corresponding pad is selected for changing volume.
2 Press and hold down the [PAD] button and simul-
taneously press VOLUME [▲ ] or [▼] to adjust the
designated pad’s volume.
• The default Pad volume is “ L9.”
L5
Pad Volume
Click ON/OFF
Press the [CLICK] button.
The click sounds in rhythm at the current tempo. (See “Adjusting the
Tempo” on page 17.)
To turn the click off, press the button once again.
14
Playing a Song
The DD-55 features 100 different songs that can be used to provide accompaniment.
(See the “Song List” on page 35.)
Select one of the songs and have listen.
Select the Song and Play
1 Press the [SONG] button.
When you press the [SONG] button, the current song number appears
10
in the display.
2 Select a Song Number.
Use the DIAL to select a song number. Song numbers will increase as
the DIAL is turned to the right (clockwise), and decrease as the DIAL
is turned to the left (counter-clockwise). (See the “Song List” on page
35.)
00 CU01 99
• Song number “ 00” is automatically selected whenever the power is
turned ON.
• With the Auto Kit Select feature turned on, selecting a song will also automatically select the best suited Drum Kit for that song. (See “Auto Kit
Select ON/OFF Setting” on page 16.)
• Song numbers are arranged in each category according to their complexity. Smaller numbers are easier to play than larger numbers.
3 Press the [START/STOP] button.
When you press the [START/STOP] button, a one- or two-measure
count-in plays, and the song starts playing.
As the song is playing, the Song’s current measure will be shown in
the display. Try playing the pads and pedals along with the song.
To stop playback of the song, press the [START/STOP] button once
again.
• You can also use the TAP START function to start songs (see page 16).
15
Loading...