Whirlpool GMH5184XV, GMH3204XV, GMH5205XV, GMH3174XV, GMH6185XV DIMENSIONS

PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS

VENTING REQUIREMENTS

Electrical: A 120-Volt, 60-Hz, AC-only, 15- or 20-amp fused electrical

supply with a fuse or circuit breaker. A time-delay fuse or time-delay circuit
breaker is recommended. It is recommended that a separate circuit serving
only this microwave oven be provided.

Microwave Hood Combination

Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.

Ref. W10238252A

2/10

CABINET OPENING DIMENSIONS

A 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent should be used.
The total length of the vent system including straight vent, elbow(s), transitions and wall

or roof caps must not exceed the equivalent of 140 ft (42.7 m) for either type of vent.
For best performance, use no more than three 90° elbows.
To calculate the length of the system you need, add the equivalent length for each vent

piece used in the system. See the following examples:

®

E

D

GMH3174XV GMH6185XV MH2175XS WMH1164XW
GMH3204XV MH1160XS WMH1162XV WMH2175XV
GMH5184XV MH1170XS WMH1163XV WMH2205XV
GMH5205XV MH1171XV WMH1164XV WMH3205XV

A B C

"

17

(43.8 cm)

15

"

(40.0 cm)

The grounded 3-prong outlet must be inside the upper cabinet.

A B

29

" (76.0 cm

"

16

(41.3 cm)

)

D E F G

A. Rectangular to round transition piece: 3

(8.3 x 25.4 cm to 15.2 cm = 1.5 m)
B. Roof cap: 3
C. 90° elbow: 3
D. 90° elbow: 6" = 10 ft (15.2 cm = 3 m)
E. Wall cap: 3
F. 4 5° elbow: 6" = 5 ft (15.2 cm = 1.5 m)
G. 90° flat elbow: 3

" x 10" = 24 ft (8.3 x 25.4 cm = 7.3 m)

" x 10" = 25 ft (8.3 x 25.4 cm = 7.6 m)

" x 10" = 40 ft (8.3 x 25.4 cm = 12.2 m)

" x 10" = 10 ft (8.3 x 25.4 cm = 3 m)

" x 10" to 6" = 5 ft

6" (15.2 cm) vent system = 73 ft (22.2 m) total

A B

6 ft (1.8 m)

2 ft

(0.6 m)

C

A. Two 90° elbows = 20 ft (6.1 m)
B. 1 wall cap = 40 ft (12.2 m)
C. 1 rectangular to round transition
piece = 5 ft (1.5 m)
D. 2 ft (0.6 m) + 6 ft (1.8 m)

straight = 8 ft (2.4 m)

D

3 " x 10" (8.3 x 25.4 cm) vent system = 73 ft (22.2 m) total

A B

6 ft (1.8 m)

30"

(76.2 cm)

min.

30" (76.2 cm) typical*

66" (167.6 cm) min.

A. 2" x 4" wall stud
B. Grounded 3-prong outlet

*30" (76.2 cm) is typical for 66" (167.6 cm) installation height.

Exact dimensions may vary depending on type of range/cooktop
below.

Rectangular to Round Transition for Roof Venting

NOTE: The minimum 3" (7.6 cm) clearance must exist between

the top of the microwave oven and the rectangular to round
transition piece so that the damper can open freely and fully.

A

12" (30.5 cm) min.
14" (35.6 cm) max.

2 ft

(0.6 m)

C

A. One 3 " x 10" (8.3 x 25.4 cm) 90° elbow = 25 ft (7.6 m)
B. 1 wall cap = 40 ft (12.2 m)
C. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m)

B

C

3" (7.6 cm)

A. Roof cap
B. 6" (15.2 cm) min. diameter round vent
C. Elbow (for wall venting only)
D. Wall cap
E. 3

F

" x 10" to 6" (8.3 x 25.4 cm to 15.2 cm)

rectangular to round transition piece

F. Vent extension piece, at least 3" (7.6 cm) high