Whirlpool AGB 437/WP, AGB 447/WP, AGB 435/WP, AGB 433/WP, AGB 445/WP INSTRUCTION FOR USE

019_03

Instructions for installation,
use and maintenance

07/2007

ELECTRIC FRYER

AGB 433/WP · AGB 437/WP
AGB 435/WP · AGB 439/WP
AGB 441/WP · AGB 445/WP
AGB 443/WP · AGB 447/WP

019-03 - Electric fryer

2

Models and dimensions page 3

Technical data 5

Installation instructions 6

Installation 6
Legal and technical requisites 6
Installation 6
Wiring 6
Unipotential 6

Using the appliance 7

Ignition 7
Emptying the bath 7

Cleaning and taking care of the
appliance 7

What to do if not using the appliance
for a long time 7
What to do if something goes wrong 7

Maintenance 7

WEEE Directive 8

Wiring diagrams 9-10

Warning 11

INDEX

019-03 - Electric fryer

3

Dimensions

C

D

A

C

D

A

AGB 441/WP / AGB 443/WP

400 x 900x 270 / 530

Weight approx.59 kg / 62 kg

Main switch

A

Pilot lamp (voltage)

C

Pilot lamp (resistance)

D

C

C

D

D

A

A

AGB 445/WP / AGB 447/WP

800 x 900x 270 / 530

Weight approx.109 kg / 120 kg

019-03 - Electric fryer

4

Dimensions

C

D

A

C

D

A

B

AGB 433/WP / AGB 435/WP

400 x 900x 875

Weight approx..70 kg / 73 kg

C

C

Main switch

A

Oil outlet drive

B

Pilot lamp (voltage)

C

Pilot lamp (resistance)

D

D

A

D

A

B

AGB 437/WP / AGB 439/WP

800 x 900x 875

Weight approx..120 kg / 131 kg

019-03 - Electric fryer

5

Technical data

The data plate is located on the rigth hand side of the
control panel and contains all the data needed for connecting
it up to the mains electricity supply.

FRYER

CAT/KAT GAS/GAZ G30 G31 G20 G25

II2H3B/P P mbar 30 30 20 -

II2H3+ P mbar 30 37 20--

II2H3+ P mbar 28 37 20 -

TIPO/TYPE

MOD.

ART.

N.

N.

Qn kW

MOD.

V KW Hz

THE APPLIANCE MUST BE CONNECTED IN COMPLIANCE WITH THE LAWS IN FORCE
AND INSTALLED IN A WELL-VENTILATED ROOM. READ THE INSTRUCTION MANUALS
BEFORE INSTALLING AND USING THE APPLIANCE.
THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL.

II2ELL3B/P P mbar 50 50 20 20

II2E+3+ P mbar 28 37 20 -

II2H3B/P P mbar 50 50 20 -

I2E P mbar - - 20 -

II2H3+ P mbar 28 37 20 -

I3B/P P mbar 30 30

m3/h

I3+ P mbar 28 37

Predisposto a gas: - Gas preset: - Prevu pour gaz:

Eingestelt für Gas: - Preparado para gas: -

--II2H3B/P P mbar 30 30

--

--

Geschuckt voor:

SE FI DK CZ SK SI

IT CH PT

ES IE GB GR

GB

25II2L3B/P P mbar 30 30

DE

FR BE

AT CH

LU

EE LV LT

EE LV LT

NO MT CY IS HU

CY

MADE IN ITALY

Model

AGB 433/WP

AGB 437/WP

AGB 435/WP

AGB 439/WP

AGB 441/WP

AGB 445/WP

AGB 443/WP

AGB 447/WP

Dim.: LxWxH

400 x 900 x 875

600 x 900 x 875

400 x 900 x 875

800 x 900 x 875

400 x 900 x 875

800 x 900 x 875

400 x 900 x 270

600 x 900 x 270

400 x 900 x 270

800 x 900 x 270

400 x 900 x 530

800 x 900 x 530

Voltage rating

230 V 3 / 400 V 3N

230 V 3 / 400 V 3N

230 V 3 / 400 V 3N

230 V 3 / 400 V 3N

230 V 3 / 400 V 3N

230 V 3 / 400 V 3N

230 V 3 / 400 V 3N

230 V 3 / 400 V 3N

230 V 3 / 400 V 3N

230 V 3 / 400 V 3N

230 V 3 / 400 V 3N

230 V 3 / 400 V 3N

Power

7.5 kW

15.0 kW

12.0 kW

24.0 kW

15.0 kW

30.0 kW

7.5 kW

15.0 kW

12.0 kW

24.0 kW

15.0 kW

30.0 kW

Lead wire / Section

4 x 2.5 mm

4 x 6 mm

4 x 6 mm

4 x 10 mm

4 x 6 mm

4 x 10 mm

4 x 2.5 mm

4 x 6 mm

4 x 6 mm

4 x 10 mm

4 x 6 mm

4 x 10 mm

2 o

5 x 1.5 mm

2 o

5 x 2.5 mm

2 o

5 x 2.5 mm

2 o

5 x 6 mm

2 o

5 x 2.5 mm

2 o

5 x 6 mm

2 o

5 x 1.5 mm

2 o

5 x 2.5 mm

2 o

5 x 2.5 mm

2 o

5 x 6 mm

2 o

5 x 2.5 mm

2 o

5 x 6 mm

2

2

2

2

2

2

2

2

2

2

2

2

019-03 - Electric fryer

6

Before beginning installation, remove all packaging from
the appliance. Some parts are protected with an adhesive
film which should be carefully removed.
Any remnants of glue should be thoroughly cleaned using
suitable substances such as benzine. Under no circum­stances should abrasive substances be used.
Fit the legs to the appliance; the appliance must be level­led using a spirit level. Slight irregularities can be levelled
by adjusting the feet themselves.
The main switch or plug should be located in the vicinity of
the appliance and easy of access. We recommend instal­ling the machine under a range hood so that all the fumes
are removed as quickly as possible. If the appliance is to
be installed near walls, dividing walls, kitchen equipment
or decorative pannelling, these should be in non-inflam­mable material or covered with non-inflammable material.
Make sure that all fire prevention standards and safety pre­cautions are strictly adhered to.

Warning !

MODELS AGB 433/WP - AGB 435/WPif this model is
going to be mounted on its own, it must be fixed to the
floor.
Fixing accessories are included.
The appliance should be fitted following the indica­tions given in the drawing below.

Legal and technical requisites

When installing the appliance, the following safety stan­dards must be adhered to:

- Local accident prevention standards

- Current CEI standards.

Installation

Installation, start-up and maintenance should only be car­ried out by expert personnel. All work required to install
the appliance should be carried out in compliance with all
local standards and regulations. The manufacturers decli­ne all responsibility where poor performance is due to in­correct installation in disregard of the above conditions.

Warning!

In compliance with international regulations, when
connecting the appliance to the mains power supply, a
device with a minimum aperture of 3 mm between con­tacts must be fitted upstream of the appliance, al­lowing omnipolar disconnection of the appliance from
the mains.

Wiring

When choosing the lead wire, make sure it has the fol­lowing characteristics: it should be at least of the H07 RN-F
type and its section should be large enough for the ap­pliance (see "Technical specifications and dimensions",
page 5).
Wire entry is underneath the appliance, on the left hand si­de. The terminal board is at the front, behind the control
panel.
Pass the wire through the core hitch and wire clamp, plug
the leads into their terminals on the board and secure
them.
The earth lead must be a little longerthan the others so
that it is the last lead to disconnect if the wire clamp
breaks.

Unipotential

The appliance must be connected up to a unipotential sy­stem. The connection screw is located underneath the ap­pliance, on the right hand side. It is labelled.

Warning!

The manufacturers cannot be held responsible for any
damage due to inadequate or incorrect installation.
Under such circumstances the guarantee will be con­sidered null and void.

Start-up

Before using the appliance for the first time, thoroughly
clean out the oil bath (see paragraph entitled “Cleaning
and Taking Care of the Appliance”).
Check that the appliance is connected up properly and
start according to instructions overleaf.

INSTALLATION INSTRUCTIONS

1

RETRO
BACK
ARRIERE
RÜCKSEITE

019-03 - Electric fryer

7

Warning!

- Beware of inexpert handling!

- Old and dirty oil or frying fat can represent a real fire
hazard; make sure only new oil or frying fat are used
each time you start frying.

- The food you intend to fry should always be dry; wet
food causes the oil to foam and overflow.

- Frying excessively large quantities of food at a time
also causes the oil to foam; never exceed 1.5 kg.

- If the level of oil in the bath falls below the low level
mark stamped on it, the risk of fire will increase.

- Never leave the appliance on without any oil in it. The
lid delivered with the appliance should always be kept
within easy reach. In case of fire, it should be used to
douse the flames.

Ignition

Check that the oil drain release is closed. Fill the bath with
oil up to the level marked. Turn on the main switch
upstream of the appliance. Turn the knob from ‘0’ to any
temperature between 100°C and 195°C; the pilot lights will
come on. The green light means that the appliance is on,
while the orange one indicates that the resistances are on.
As soon as the required temperature is reached, the oran­ge light will go off. To turn the appliance off, simply turn the
knob back to '0'.

Emptying the bath

Open the oil drain tap. The appliance is fitted with an oil­collecting container complete with filter.

CLEANING AND TAKING CARE OF THE
MACHINE

Warning!

Never clean the appliance with jets of water, whether di­rect or pressurised. Allow the machine to cool down
before cleaning

Before starting to clean the appliance, disconnect from the
mains. Using the hook provided (see drawing 2), you can lift
out the elements to make cleaning the appliance easier and
far more thorough. Lift the elements as far as they will go. To
lower them after cleaning, pull out the button on the left hand
side. All steel parts should be washed in warm water, using a
neutral detergent, then rinsed thoroughly to eliminate any re­sidual detergent. Dry using a dry cloth. Avoid using abrasive
or corrosive detergents which could damage the steel.

What to do if not using the appliance for
a long time

Thoroughly clean and dry the machine as described.
Disconnect the power supply.

What to do if something goes wrong

If anything goes wrong, immediately turn the appliance off,
then turn off the power supply at the switch located upstream
of the appliance, and call the aftersales department.

MAINTENANCE

All maintenance should be carried out by qualified personnel
only. Before carrying out any maintenance work, unplug the
appliance or turn off the switch upstream of the appliance.

USING THE APPLIANCE

2

- Bottone
di sgancio

- Pull out button

- Bouton de
déclanchement

- Auslösungknopf

019-03 - Electric fryer

8

THE 2002/96/EC DIRECTIVE (WEEE):
information to users

This informational note is meant only for owners
of equipment marked with the symbol shown in
Fig. A on the adhesive label featuring the tech­nical specifications applied on the actual pro-

duct (the label also giving the serial number).

This symbol indicates that the product is classified, ac­cording to the regulations in force, as an item of electrical
and electronic equipment and conforms to EU Directive
2002/96/EC (WEEE) meaning that, at the end of its service
life, it must be treated separately from domestic waste,
i.e. it must be handed in free of charge to a separate wa­ste electrical and electronic equipment collection centre
or returned to the reseller when buying a new equivalent
item of equipment.

The user is responsible for delivering the unit at the end of
its life to the appropriate collection facilities. Failure to do
so shall result in the user being subject to the penalties
prescribed by the legislation in force on waste.
Suitable separated collection so that the unit no longer
used can be sent off for environmentally compatible recy­cling, treatment and disposal helps avoid possible negati­ve effects on the environment and on health and facilita­tes the recycling of the product's component materials.

For more detailed information on available collection sy­stems, contact the local waste disposal service or the
shop you purchased the unit from.

Producers and importers fulfil their responsibility for envi­ronmentally compatible recycling, treatment and disposal
both directly and by joining a collective scheme.

019-03 - Electric fryer

9

Wiring diagrams

AGB 433/WP - AGB 435/WP
AGB 441/WP - AGB 443/WP

123

11 12 13

mC

B2

R

C2

12 5634

mA

L1 L2 L3 N

C1

1mA2 3 4

L1 L2 L3

230 V 3

PE

B1

56

PE

F2

6 2 4

F1

H2 H1

400 V 3N

1 2 34

mC

1 3 5

Line input terminal board

mA

Commutating terminal board

mC

Switch

B1

Microswitch

B2

Safety contactor

C1

Adjusting contactor

C2

Adjusting thermostat

F1

Safety thermostat

F2

Green pilot lamp

H1

Orange pilot lamp

H2

Resistance

R

019-03 - Electric fryer

10

Wiring diagrams

AGB 437/WP - AGB 439/WP
AGB 445/WP - AGB 447/WP

mC

C1

B1

VUW

YXZ

C2

B2

F2

VUW

R

YXZ

mC

C2

C1

F1

B1

R

B2

F2

F1

H2 H1

H2 H1

Line input terminal board

mA

Commutating terminal board

mC

Switch

B1

Microswitch

B2

Safety contactor

C1

Adjusting contactor

C2

Adjusting thermostat

F1

Safety thermostat

F2

Green pilot lamp

H1

Orange pilot lamp

H2

Resistance

R

1mA 2 3 4

L1 L2 L3

230 V 3

56

PE

1mA2 3 4

L1 L2 L3 N

6 2 4

mC

56

400 V 3N

PE

1 3 5

1 2 34

019-03 - Electric fryer

11

WARNING

THE MANUFACTURER CANNOT BE HELD RESPONSIBLE
FOR ANY INACCURACIES IN THIS BOOKLET DUE TO
COPYING OR PRINTING ERRORS.

DUE TO ITS POLICY OF CONTINUAL PRODUCT IMPRO­VEMENT, THE MANUFACTURER RESERVES THE RIGHT
TO MAKE ANY CHANGES DEEMED NECESSARY.

THE MANUFACTURER CANNOT BE HELD RESPONSI­BLE IF THE INSTRUCTIONS CONTAINED IN THIS MA­NUAL ARE NOT OBSERVED.

WHIRLPOOL EUROPE srl

V.le Guido Borghi, 27

I – 21025 Comerio – VA