Weider PRO 2250 Owner's Manual

www.weider.com
odel No. WESY1955.1
M Serial No.
Write the serial number in the space above for reference.
Serial Number Decal (under seat)
QUESTIONS?
As a manufacturer, we are com­mitted to providing complete customer satisfaction. If you have questions, or if parts are missing,
DO NOT CONTACT THE STORE; please contact Customer Care.
IMPORTANT: You must note the product model number and serial number (see the drawing above) before contacting us:
USERʼS MANUAL
CALL TOLL-FREE:
1-877-992-5999
Mon.–Fri. 6 a.m.–6 p.m. MT Sat. 8 a.m.–4 p.m. MT
ON THE WEB: www.weiderservice.com
CAUTION
Read all precautions and instruc­tions in this manual before using this equipment. Save this manual for future reference.
TABLE OF CONTENTS
Keep hands and fingers clear of this area.
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
I
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
CABLE DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning decal(s). If a decal is
missing or illegible, call the tele­phone number on the front cover of this manual and request a free replacement decal. Apply the decal in the location shown. Note: The
decal(s) may not be shown at actual size.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your weight system before using your weight sys-
em. ICON assumes no responsibility for personal injury or property damage sustained by or
t through the use of this product.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure that all users of the weight system are ade­quately informed of all precautions.
3. Your weight system is intended for home use only. Do not use your weight system in a commercial, rental, or institutional setting.
4. Use your weight system only on a level sur­face. Cover the floor beneath the weight system to protect the floor.
5. Inspect and properly tighten all parts regu­larly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away from your weight system at all times.
7. Your weight system should not be used by persons weighing more than 300 lbs. (136 kg).
8. Wear appropriate exercise clothes while exercising; do not wear loose clothes that could become caught on your weight sys­tem. Always wear athletic shoes for foot protection while exercising.
9. Keep hands and feet away from moving parts.
10. Never release the press arm, butterfly arms,
leg lever, lat bar, or nylon strap while weights are raised. The weights will fall with great force.
11. Make sure that the cables remain on the pul­leys at all times. If the cables bind while you are exercising, stop immediately and make sure that the cables are on the pulleys.
12. Always stand on the foot plate while per­forming an exercise that could cause the weight system to tip.
13. Never release the arms, leg lever, lat bar, or handle strap while weights are raised; the weights will fall with great force.
14. Always disconnect the lat bar from the weight system before performing an exer­cise that does not require the lat bar.
15. If you feel pain or dizziness while exercising, stop immediately and begin cooling down.
16. Use your weight system only as described in this manual.
3
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER PRO™ 2250 weight system. The weight system offers an impressive array of weight stations designed to devel­op every major muscle group of the body. Whether
our goal is to tone your body, build dramatic muscle
y size and strength, or improve your cardiovascular sys­tem, the weight system will help you to achieve the specific results you want.
For your benefit, read this manual carefully before you use the weight system. If you have questions
after reading this manual, please see the front cover of
ASSEMBLED DIMENSIONS: Height: 6 ft. 4 in. (193 cm) Width: 3 ft. 2 in. (97 cm) Length: 4 ft. 5 in. (135 cm)
Butterfly Arm
this manual. To help us assist you, note the product model number and serial number before contacting us. The model number and the location of the serial num­ber decal are shown on the front cover of this manual.
To avoid a registration fee for any service needed under warranty, you must register the weight sys­tem at www.weiderservice.com/registration.
Before reading further, please familiarize yourself with the parts that are labeled in the drawing below.
High Pulley Station
Lat Bar
Right Side
Backrest
Press Arm
Seat
Leg Lever
Low Pulley Station
Foot Plate
Left Side
Weight Stack
Note: The terms “right side” and “left side” are determined relative to a person sitting on the seat; they do not correspond to right and left on the drawings in the manual.
4
M10 x 75mm Bolt (22)
M10 x 67mm Bolt (11)
M10 x 80mm Bolt (16)
M10 x 90mm Bolt (85)
M10 x 198mm Bolt (59)
M8 x 70mm Bolt (81)
M8 x 117mm Bolt (68)
M10 x 67mm Carriage Bolt (14)
M10 x 95mm Bolt (71)
M8 x 67mm Carriage Bolt (86)
M6 x 65mm Screw (43)
PART IDENTIFICATION CHART
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-
ng is the key number of the part, from the PART LIST near the end of this manual. Note: Some small parts
i
may have been preattached. If a part is not in the hardware kit, check to see if it has been preattached.
5
M6 Washer (10)
M8 Washer (8)
M4 Washer (82)
M10 x 58mm Bolt (7)
M
10 x 45mm Bolt (83)
M10 x 48mm Bolt (12)
M8 x 45mm Bolt (72)
M8 x 57mm Bolt (80)
M6 x 50mm Carriage Bolt (38)
M6 x 50mm Screw (24)
M8 x 65mm Carriage Bolt (1)
M10 Washer (9)
M6 x 16mm Screw (18)
M4 x 20mm Screw (56)
M6 Nylon Locknut (2)
M8 Nylon Locknut (3)
M10 Nylon Locknut (21)
6
ASSEMBLY
ake Assembly Easier
M
Everything in this manual is designed to ensure that the weight bench can be assembled suc­cessfully by almost anyone. Set aside plenty of time, so that assembly will go smoothly.
Before beginning assembly, carefully read the fol­lowing information and instructions:
• Assembly requires two persons.
• Because of its size, the weight bench should be assembled in the location where it will be used. Make sure that there is enough clearance to walk around the weight bench as you assemble it.
• Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
• Tighten all parts as you assemble them, unless instructed to do otherwise.
• As you assemble the weight bench, make sure all
arts are oriented as shown in the drawings.
p
• For help identifying small parts, use the PART IDENTIFICATION CHART on page 5.
• Assembly requires the included hex key(s)
and the following tools (not included):
two adjustable wrenches
one rubber mallet
one standard screwdriver
one Phillips screwdriver
Assembly may be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.
Frame Assembly
1.
Before beginning assembly, make sure that you have read and understand the informa­tion in the box above.
Attach a Stabilizer Foot (51) to the Stabilizer (5) with two M4 x 20mm Screws (56) and two M4 Washers (82). Attach another Stabilizer Foot in
the same way.
Insert two M10 x 67mm Carriage Bolts (14) up through the Stabilizer (5). Insert two M8 x 65mm Carriage Bolts (1) up through the Base (4). Note:
It may be helpful to place a piece of tape over the bolt heads to hold the Carriage Bolts in place.
Orient the Stabilizer (5) so that the small holes are on the indicated side. Attach the Base (4) to the Stabilizer with the two M10 x 67mm Carriage Bolts (14) and two M10 Nylon Locknuts (21). Do
not tighten the Nylon Locknuts yet.
1
21
4
1
51
5
Small
Holes
82
14
56
51
7
2. Slide the Front Upright (42) onto the M8 x 65mm Carriage Bolts (1) in the Base (4). Hand tighten two M8 Nylon Locknuts (3) onto the Carriage
olts. Do not tighten the Nylon Locknuts yet.
B
2
42
3
3. Attach the two Weight Guides (62) inside of the Stabilizer (5) with two M10 x 67mm Bolts (11), two M10 Washers (9), two 13mm Spacers (61), and two M10 Nylon Locknuts (21).
See step 1. Tighten the M10 Nylon Locknuts (21).
Slide two Weight Bumpers (19) onto the Weight Guides (62). Stack the six Weights (25) on the Weight Bumpers (19). Make sure that all of the
Weights are turned so the large pin grooves are on the bottom of the Weights and are on the same side of the weight stack.
Press the Weight Tube Bumper (64) into the end of the Weight Tube (63). Insert the Weight Tube into the stack of Weights (25). Make sure that
the pins on the Weight Tube are resting in the pin grooves in the upper Weight.
Lubricate the insides of the holes in the Top Weight (76). Slide the Top Weight onto the Weight Guides (62).
4
1
3
62
76
Lubricate
Pin
Pin
Groove
Pin
Groove
19
63
64
25
9
11
9
61
5
21
8
Loading...
+ 16 hidden pages