VTech VT5820 User Manual

Introduction

EXPAND YOUR VT5831 SYSTEM. YOUR BASE WILL WORK WITH UP TO 6 HANDSETS!!!

IMPORTANT:

The VT5820 is an Accessory Handset for use with the VT5831 system. You must have this model in order to use the VT5820 Accessory Handset.

This manual is designed to familiarize you with the VT5820 Accessory Handset setup, registration and basic functions. For detailed operational instructions, please refer to the VT5831 User's Manual.

To order additional system Handsets (model# VT5820), battery packs, or headsets, call VTech Communications Inc at 1-800-595-9511.

STOP!!

If you have questions about this product, or if you're having difficulty with setup or operation, do not return your phone to the store. Call our Customer Support Center at:

1-800-595-9511 In Canada, call 1-800-267-7377

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool).

5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.

6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from overheating, these openings must not be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation where proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it.

9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the appliance is subsequently used.

11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock

12. Unplug this product from the wall outlet and refer servicing to VTECH under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

Important Safety Instructions

B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls

may result in damage. E. If the product has been dropped and the cabinet has been damaged. F. If the product exhibits a distinct change in performance.

13. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

14. Do not use the telephone to report a gas leak in the vicinity of the leak.

VTECH COMMUNICATIONS INC

Customer Service: 1-800-595-9511. In Canada, call VTech Electronics Ltd. at 1-800-267-7377.

SAVE THESE INSTRUCTIONS

Setup

Registration And Operation Of The VTECH VT5820 Accessory Handset

Your VTECH VT5831 system can operate up to 6 Handsets.

The VTECH accessory Handset consists of the following:

Handset Charger

Charger Wall

Mounting Bracket

Handset

Telephone Line Cord

Belt Clip

Battery Pack

Setup Of The VT5820 Accessory Handset

1. Plug the AC power adapter

into an electrical outlet.

2. Remove the Handset battery cover by pressing on the

3. Place the new battery pack

4. Replace the battery cover by

5. Place the Handset in the

indent and sliding downward. in the Handset, with the

metal contacts aligned with the charge contacts in the battery compartment.

sliding it upward. Charge Cradle, and allow it to

charge for 12 hours. After the initial charge, a maintenance charge of 8 hours should be sufficient.

Installation of Battery Pack in Handset

Follow the steps below:

1. Remove the battery cover by

2. Place the new battery pack in

3. Replace the battery cover by

4. If the new battery pack is not

As you register additional Handsets to the system, they will be assigned extension numbers in the following order: HANDSET 2, HANDSET 3, HANDSET 4, and so forth.

Whenever a charged Handset battery pack is installed, the Handset will automatically begin SEARCHING FOR BASE (if previously registered), or it will prompt you to ENTER BASE ID to register the new Handset.

pressing on the indent and sliding downward.

the Handset with the metal contacts aligned with the charge contacts in the battery compartment.

sliding it upwards. already charged, place the

Handset in the charger, and allow it to charge for 12 hours. After initial charge, a maintenance charge of 8 hours should be sufficient.

BEFORE USING YOUR HANDSET(S), CAREFULLY PEEL OFF THE PROTECTIVE FILM, COVERING THE DISPLAY.

Registration

Enter Base ID Code

1. After charging the Handset, remove it from its Charge Cradle; the screen will display:

alternating with this screen:

2. If, after charging the Handset, you see:

3. Press NEW. You will now see the ENTER BASE ID screen as described in step 1.

4. Find the BASE ID Code by doing the following: (the Base must be in idle (OFF) mode) A. At the Base, press MENU B. Scroll down to DISPLAY BASE-ID C. Press OK. The Base screen will display the 15-digit ID Code.

Afterwards, it will return to the idle screen.

5. Enter the 15-digit Base ID Code into the Handset; then press OK.

NOTE: The 15-digit BASE ID Code may contain numbers and characters, such as . Make sure you enter all 15 digits.

6. Wait approximately 15 to 60 seconds. You will hear confirmation beeps from the Base and Handset. The newly registered Handset will now assign itself the lowest Handset number not previously assigned to a different system Handset (1 through 6).

7. If the Handset displays REJECTED BY BASE or continues to display SEARCHING FOR BASE for well beyond 60 seconds, try the registration process again by repeating the above steps.

Congratulations! You can now enjoy the benefits of your VTECH Multi-Handset system.

The Handset Layout

1. Antenna

2. Earpiece

3. Headset Jack (2.5mm)

4. On (Flash)

5. Dialing Keys (0-9, , #)

6. Speakerphone

7. Message Waiting LED

8. LCD Display

9. Soft Keys

10. Volume

11. Off (Clear)

12. Sound Select

13. Microphone

+ 14 hidden pages