＜3ft (1m)
＞3ft (1m)
Specifications are subject to change without notice.
© 2018 VTech Communications, Inc. All rights reserved.
07/18. VM3252-2_QSG_V5.
Document order number: 96-011939-050-100
Quick start guide
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
What’s in the box
VM3252 VM3252-2
1
Install the battery
3
Power on or off the baby monitor
Slide the ON/OFF switch to power
on or off your baby unit.
Press and hold to power on or
off your parent unit.
Caution
• The default volume of your parent unit
is level 3, and the maximum volume is
level 5. If you experience high-pitched
screeching noise from your baby
monitor while positioning:
- Make sure your baby unit and parent unit
are more than 1 meter (3 feet) apart, OR
- Turn down the volume of your parent unit.
4
Positioning the baby monitor
5
Status check
Once you power on both your baby unit and parent unit, your parent unit displays ima ge
from the baby unit, and the LINK LED light turns on.
The POWER LED light of baby unit turns on.
Adjust speaker volume
Press VOL+ / VOL- to adjust your parent
unit speaker volume. It determines the
volume of sound transmitted from your
baby units.
Zoom
Press to zoom in or out.
Talk to your baby unit
Press and hold TALK and speak to your
parent unit. Your voice is transmitted to
the baby unit.
Use the menu
Press MENU to enter the menu, or save
a setting. You can use the parent unit for
advanced settings or operations, such as to
play or stop the baby unit lullaby, or to adjust
the baby unit sound sensitivity.
While in the menu:
• Press or to scroll among the me nu
options.
• Press SELECT or to enter the desire d
submenu.
• Press or to select an item .
• Press SELECT to confirm your selection .
• Press or to exit the submenu.
Turn off the screen
Press and hold LCD ON/OFF to switch
off the screen. You can still hear sound
from the selected baby unit.
Tip
• Press any keys on the pa rent unit to turn on
the screen again.
Basic operation - Parent unit
Press and hold
Submenu
Main menu
> 3ft (1m)
Long press
VM3252
VM3252-2
Video Monitor
6U]KXOTMUT
3OYKKTLUTIZOUT
6U]KXOTMULL
3OYKKTLUTIZOUT
6U]KXOTMUT
3OYKKTLUTIZOUT
Long press Long press
2
Connect the baby monitor
NOTESNOTE
• The rechargeable battery is pre-installed in your parent unit.
• Use only the power adapters supplied with this product.
• Make sure the baby mo nitor is not connected to the switc h controlled electric outl et.
• Connect th e power adapters in a vertical o r floor mount position only. The adapte rs’ prongs are
not designed to hold the weight of baby moni tor, so do not connect them to any ceiling, un derthe-table, or cabinet outlets. O therwise, the adapters may not p roperly connect to the outle ts.
• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.
THIS SIDE UP
THIS SIDE UP
Press MENU when the parent unit is idle. Press or to choose , then press SELECT or .
Press or to choose , then press SELECT to confirm your selection.
For VM3252-2 only
If you are viewing baby unit , the POWER LED light of baby unit turns on.
As baby unit is not being viewed, its POWER LED light flashes.
NOTESNOTE
Note
• If you power on only one baby unit, your parent unit may display and the LINK LED light flashes.
Press to switch to the baby unit you have powered on.
Status check - Two baby units
Change different views - Patrol
10s
Press .
Press to switch to another camera in SINGLE-CAM mode.
Change different views - Single-cam
Use a pencil to mark two holes in parallel.
Make sure they are the same distance apart
as the wall mount holes on the baby unit.
NOTESNOTE
Note
• Check for reception strength and camera
angle before drilling the holes.
Items to purchase
You will need to purchase the following
items separately to mount your baby unit:
2 screws
2 anchors
Mount the baby unit on dry wall (optional)
Adjust the camera angle.
Drill two holes in the wall. If you drill the holes
into a stud, go to step 3.
-OR-
If you drill the holes into an object other than
a stud, insert the wall anchors into the holes.
Tap gently on the ends with a hammer until
the wall anchors are flush with the wall.
Insert the screws into the holes and
tighten the screws until only 1/4 inch
of the screws are exposed.
Align the wall mount holes on the
baby unit with the screws on the wall.
Slide the baby unit down until it locks
into place.
Night vision
The baby unit has infrared LEDs that
allow you to see your baby clearly at
night or in a dark room. When the baby
unit being viewed detects low light
levels, the infrared LEDs are switched
on automatically. The images from the
baby unit are in black and white, and
appears on the screen.
Notes
• It is normal if you se e a short white glare
on your parent unit screen as the baby unit
is adapting to the dark environment.
• When the infrare d LEDs are on, the images
are in black and white. This is normal .
Tip
• Depending on the surroundings and other
interfering factors, like lightings, objects,
colors and backgrounds, the display
resolution may vary. Adjust the baby unit’s
angle or place the baby unit at a higher
level to prevent glare and blurry display.
Overview - Parent unit
Sound sensitivity and sound activation
Light sensor
Camera
Microphone
POWER LED light
Wall mount holes
Infrared LEDs
Overview - Baby unit
ON/OFF switch
Speaker
Power jack
VOL -
VOL +
Speaker
Power jack
Stand
On/off
TALK
LCD ON/OF F
Arrow keys
MENU/SELECT
LED lights
Microphone
Zoom / Back
NOTESNOTE
Note
• The types of screws and anchors you need
depend on the composition of the wall.
Sound sensitivity
With sound sensitivity setting, you can ch oose to hear sounds
from the baby unit all the time, or to hear sounds that exceed
a certain level. The default level Highest allows you to hear all
sounds (including background noises).
63ē
Sound activation
When sound activation is on, the parent unit screen s tays off to save
power when the baby unit detects no sound.
Once the baby unit detects sounds that are louder t han the chosen
sound sensitivity level, the parent unit screen tur ns on automatically.
It will then turn off again after 50 seconds of no sou nd detection.
If you set the sound
sensitivity to a lower level
(e.g. Medium), you will only
hear sounds that exceed the
selected level. The baby unit
may not detect soft sounds,
and the parent unit speaker
may remain quiet.
For details, please see Adjust
the sound sensitivity of
the baby unit in the User’s
manual.
Dim mode
The dim mode is to help you save the parent unit power. Your parent unit display will dim
automatically after 10 minutes of inactivity, in which there is neither key pressed nor alert
received from the baby unit.
10 min inactivity
Press any buttons
NOTESNOTE
Note
• While the sc reen is dimmed, any keypress or a lert message will trigg er the screen to return to
the preset brightness level. After 10 m inutes of inactivity, it will resum e to dim mode.
Loading...