VTech LS6325-2, LS6325-4, LS6326-5, LS6325, LS6325-5 User Manual
...
Quick start guide
for models LS6325/LS6325-2/LS6325-3/
LS6325-4/LS6325-5/LS6326-5
Install the telephone base and
charger(s)
Install the telephone base and charger(s) as
shown below.
Telephone
wall jack
If you have
DSL high
speed
Internet
service, a
DSL filter (not
included) is
required.
Telephone
line cord
Telephone
base power
adapter
Electrical
outlet not
controlled by
a wall switch
Charger
adapter
Battery installation and charging
Install the battery as shown below. After
installing the battery, you may be able to make
and receive short calls. For best performance,
charge the handset battery for at least 16 hours
before use.
1
If the batter y
compartment cover is on
the handset, press on the
indentation and slide the
cover to remove.
3
Place the battery with
the label THIS SIDE UP
facing up and the wires
inside the battery
compartment.
2
Plug the battery
connector securely
into the socket inside
the handset battery
compartment, matching
the color-coded label.
4
Align the cover at
against the battery
compartment, then slide
it towards the center of
the handset until it clicks
into place.
Make, answer and end a call
Make a call
Press /FLASH or .
1.
You hear a dial tone.
Dial the number.
2.
Make a predial call
Dial the number.
1.
Press /FLASH or .
2.
Answer a call
Press /FLASH, or any of the dialing keys
(0-9, #, TONE ).
End a call
Press OFF/CLEAR or put the handset in the
telephone base or charger.
Push to talk (PTT)
You can directly broadcast messages from one
handset to the speakerphone of one or all other
handsets. Any handset you call can respond by
pressing PUSH TO TALK to begin a two-way
communication.
When the connection is made, both the caller
and the destination handsets display Press
and hold [PTT] to talk and beep once.
Only one handset can be talk at a time. To do
so, press and hold PUSH TO TALK.
For complete PTT instructions, please refer
to your user’s manual.
Charger
Telephone base
Use only the power adapters and batteries
•
supplied with your VTech telephone.
For complete feature instructions, please
•
refer to your user’s manual.
5
Charge the handset by
placing it in the telephone
base or charger. The
CHARGE light is on when
the handset charges.
CHARGE
light
Turn the answering system
on or off
The answering system must be turned on to
answer and record messages.
When the answering system is turned on,
the /ANS ON/OFF light on the telephone
base will be on and ANS ON will display on
the handset.
To turn on or off with the telephone
base:
Press /ANS ON/OFF
•
to turn the built-in
answering system on or
off. When the answering
system is turned on, it
announces,
be answered.”
the answering system is
turned off, it announces,
“Calls will not be answered.”
To turn on or off with a handset:
Press MENU/SELECT when the handset is
1.
not in use.
Press / VOL or VOL/CID to highlight
2.
>
Answering sys, then press MENU/SELECT.
Press / VOL or VOL/CID to highlight
3.
>
Answer ON/OFF, then press
MENU /SELECT.
Press / VOL or VOL/CID to choose
4.
>
On or >Off, then press MENU/SELECT.
“Calls will
When
Outgoing announcement
The telephone is preset with a greeting that
answers calls with
message after the tone.”
preset announcement, or replace it with
your own.
Use a handset to record your own
announcement:
Press MENU/SELECT when the handset is
1.
not in use.
Press / VOL or VOL/CID to highlight
2.
>
Answering sys, then press MENU/SELECT.
Press MENU/SELECT to highlight
3.
>
Announcement.
The handset announces,
4.
To record, press 7.”
The handset announces,
5.
tone. Press 5 when you are done.”
After the tone, speak towards the
6.
microphone of the handset.
Press 5 when nished.
7.
The answering system automatically plays
8.
back the newly recorded announcement.
Press 5 to stop the playback at any time; 2 to
replay the recorded announcement; or 7 to
record again if desired.
“Hello, please leave a
You can use this
“To play, press 2.
Press 7 to record.
“Record after the
To play messages with the
telephone base:
Pressress /PLAY/STOP to listen to messages.
Options during playback:
Press /VOL or VOL/ to adjust the
•
speaker volume.
Press /SKIP to skip to the next message.
•
Press /REPEAT to repeat the message
•
currently playing. Press /REPEAT twice to
listen to the previous message.
Press X/DELETE to delete the current
•
message. The system advances to the next
message.
Press /PLAY/STOP to stop.
•
To play messages with
a handset:
Press MENU/SELECT when the handset is
1.
not in use.
Press MENU/SELECT to highlight
2.
>
Play messages. If you have either new
or old messages, the messages play
automatically.
If you have both new and old messages:
To play new messages, press
•
MENU /SELECT to highlight
>
Play new msgs.
To play old messages, press VOL/CID
•
to highlight >Play old msgs, then press
MENU /SELECT.
Options during playback:
Press / VOL or VOL/CID to adjust the
•
speaker volume.
Press EQ to adjust the handset message
•
playback audio quality.
Press 6 to skip to the next message.
•
Press 4 to repeat the message currently
•
playing. Press 4 twice to listen to the previous
message.
Press 3 to delete the current message. The
•
system advances to the next message.
Press 5 to stop.
•
IMPORTANT!
If your product is not working properly:
Refer to the Troubleshooting section of the
•
user’s manual.
Visit our website at www.vtechphones.com
•
or call 1 (800) 595-9511.
In Canada, go to www.vtechcanada.com or
dial 1 (800) 267-7377.
96-007349-010-100
Loading...