Page 1
Service Manual
Model #: VIZIO VX42L HDTV10A /
VW42L HDTV10A
V, Inc
320A Kalmus Drive Costa Mesa, CA 92626
TEL : +714-668-0588 FAX :+714-668-9099
Top Confidential
Page 2
Table of Contents
CONTENTS PAGE
Sections
1. Features 1-1
2. Specifications 2-1
3. On Screen Display 3-1
4. Factory Preset Timings
5. Pin Assignment
4-1
5-1
6. Main Board I/O Connections 6-1
7. Theory of Circuit Operation 7-1
8. Waveforms 8-1
9. Trouble Shooting 9-1
10. Block Diagram 10-1
11. Spare parts list 11-1
12. Complete Parts List 12-1
Appendix
1. Main Board Circuit Diagram
2. Main Board PCB Layout
3. Assembly Explosion Drawing
Block Diagram
VIZIO VX42L/VW42L HDTV10A Service Manual
Page 3
VINC Service Manual
VIZIO VX42L/VW42L HDTV10A
COPYRIGHT © 2000 V, INC. ALL RIGHTS RESERVED.
IBM and IBM products are registered trademarks of International Business Machines
Corporation.
Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.
VINC and VINC products are registered trademarks of V, Inc.
VESA, EDID, DPMS and DDC are registered trademarks of Video Electronics Standards
Association (VESA).
Energy Star is a registered trademark of the US Environmental Protection Agency (EPA).
No part of this document may be copied, reproduced or transmitted by any means for any
purpose without prior written permission from VINC.
FCC INFORMATION
This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that the interference will not occur in a particular installation. If this equipment
does cause unacceptable interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures -- reorient or relocate the receiving
antenna; increase the separation between equipment and receiver; or connect the into an
outlet on a circuit different from that to which the receiver is connected.
FCC WARNING
To assure continued FCC compliance, the user must use a grounded power supply cord and
the provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized
changes or modifications to Amtrak products will void the user’s authority to operate this
device. Thus VINC Will not be held responsible for the product and its safety.
CE CERTIFICATION
This device complies with the requirements of the EEC directive 89/336/EEC with regard to
“Electromagnetic compatibility.”
SAFETY CAUTION
Use a power cable that is properly grounded. Always use the AC cords as follows – USA (UL);
Canada (CSA); Germany (VDE); Switzerland (SEV); Britain (BASEC/BS); Japan (Electric
Appliance Control Act); or an AC cord that meets the local safety standards.
VIZIO VX42L/VW42L HDTV10A Service Manual
Page 4
Chapter 1 Features
1. Built in TV channel selector for TV viewing
2. Simulatnueous display of PC and TV images
3. Connectable to PC’s analog RGB port
4. Built in S-video, HDTV, composite video, HDMI and TV out
5. Built in auto adjust function for automatic adjument of screen display
6. Smoothing function enables display of smooth texts and graphics even if image
withresolution lower than 1366x768 is magnified
7. Picture In Picture (PIP) funtion to show TV or VCR images
8. Power saving to reduce consumption power too less than 3W
9. On Screen Display: user can define display mode (i.e. color, brightness,
contrast, sharpness, backlight), sound setting, PIP, TV channel program,
aspect and gamma or reset all setting.
CONFIDENTIAL – DO NOT COPY
Page 1-1
File No. SG-0211
Page 5
Chapter 2 Specification
1. LCD CHARACTERISTICS
Type: 42.0 WXGA TFT LCD
Size: 42.02inch
Display Size: 42.02 inches (1067.308mm) diagonal
Outline Dimension: 983 mm (H) x 576 mm (V) x 51 mm (D) (Typ.)
Pixel Pitch: 0.227mm x 0.681mm x RGB
Pixel Format: 1366 horiz. By 768 vert. Pixels RGB strip arrangement
Contrast ratio: 1.CR : 800(Min.) 1000(Typ)
Luminance, White: 500 cd/m
2 (Typ)
Display Operating Mode: normally Black
Surface Treatment: Hard Coating (3H) ,Anti-glare treatment of the front polarizer.
2. OPTICAL CHARACTERISTICS
Viewing Angle (CR>10)
Left: 89°typ.
Right: 89°typ.
Top: 89°typ.
Bottom: 89°typ.
3. SIGNAL (Refer to the Timing Chart)
Sync Signal
(1) Type: TMDS
(2) Input Voltage Level: 90~240 Vac, 50/ 60 Hz
4.Input Connectors
RJ11, D-SUB15PIN (MINI, 3rows), Headphone, HDMIX2, RCAX3 (component),
RCAX2 (AUDIO in), RCAX3 (composite), RCAX2 (AUDIO in), S-Video, Tuner
5. POWER SUPPLY
Power Consumption: 280W MAX
Power OFF: to less than 3W MAX
CONFIDENTIAL – DO NOT COPY
File No. SG-0211
Page 2-1
Page 6
6.Speaker
Output 10W (max) X2
7. ENVIRONMENT
7-1. Operating Temperature: 5c~35c (Ambient)
7-2. Operating Humidity: Ta= 35 °C, 90%RH (Non-condensing)
7-3. Operating Altitude: 0 - 14,000 feet (4267.2m)(Non-Operating)
8. DIMENSIONS (Physical dimension)
Width: 1028 mm.
Depth: 99.0mm
Height: 694.0mm
9. WEIGHT (Physical weight)
a. Net: 36.0+/-0.5kgs
b. Gross: 43+/-0.5kgs
Precaution
Please pay attention to the followings when you use this TFT LCD module.
9-1. MOUNTING PRECAUTIONS
(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. Twisted
stress) is not applied to the module. And the case on which a module is mounted
should have sufficient strength so that external force is not transmitted directly to
the module.
(3) Please attach the surface transparent protective plate to the surface in order to
protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist
external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable
because the former generates corrosive gas of attacking the polarizer at high
temperature and the latter causes circuit break by electro-chemical reaction.
CONFIDENTIAL – DO NOT COPY
File No. SG-0211
Page 2-2
Page 7
(6) Do not touch, push or rub the exposed polarizes with glass, tweezers or anything
harder than HB pencil lead. And please do not rub with dust clothes with chemical
treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some
cosmetics are detrimental to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or
other soft materials like chamois soaks with petroleum benzene. Normal-hexane
is recommended for cleaning the adhesives used to attach front / rear polarizers.
Do not use acetone, toluene and alcohol because they cause chemical damage to
the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with
polarizer causes deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
9-2. OPERATING PRECAUTIONS
(1) The spike noise causes the mis-operation of circuits. It should be lower than
following voltage :
V=±200mV(Over and under shoot voltage)
(2) Response time depends on the temperature. (In lower temperature, it becomes
longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes
lower.)And in lower temperature, response time (required time that brightness is
stable after turned on) becomes longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes
damage to polarizer or electrical contacted parts. And after fading condensation,
smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to
occur.
(6) Module has high frequency circuits. System manufacturers shall do sufficient
suppression to the electromagnetic interference. Grounding and shielding
methods may be important to minimize the interference.
CONFIDENTIAL – DO NOT COPY
Page 2-3
File No. SG-0211
Page 8
9-3. HANDLING PRECAUTIONS FOR PROTECTION
(1) The protection film is attached to the bezel with a small masking tape. When the
protection film is peeled off, static electricity is generated between the film and
polarizer. This should be peeled off slowly and carefully by people who are
electrically grounded and with well ion-blown equipment or in such a condition,
etc.
(2) When the module with protection film attached is stored for a long time,
sometimes there remains a very small amount of glue still on the bezel after the
protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel surface or its
vestige is recognized, please wipe them off with absorbent cotton waste or other
soft material like chamois soaked with normal-hexane.
CONFIDENTIAL – DO NOT COPY
Page 2-4
File No. SG-0211
Page 9
Chapter 3 On Screen Display
On Screen Display (OSD) is a friendly interface providing the function adjusting in our system.
Customers could operate it only by few buttons. There is the introduction of the OSD.
Main unit button
MENU OK
CH ▲ ↑
CH ▼ ↓
VOL + ←
VOL - →
Input
[MENU]
“MENU” button could star the OSD which could adjust the performance and set up the setting
between the different input sources. There are the structures.
TV Source
CONFIDENTIAL – DO NOT COPY
Page 3-1
File No. SG-0211
Page 10
A. Picture：(Bold: Default)
a. Picture Mode (Standard/Movie /Game / Custom)
b. Backlight (0~100, 90)
c. Contrast (0~100, 50)
d. Brightness (0~100, 50)
e. Color (saturation)(0~100, 50)
f. Tint (hue) (-32~32, 0)
g. Sharpness (0~7, 4)
h. Color Temperature (Cool/Normal/Warm/Custom)
B. Audio：(Bold: Default)
a. Volume (0~100, 25)
b. Bass (0~100, 50)
c. Treble (0~100, 50)
d. Balance (-50~50, 0)
e. Surround (ON/OFF)
f. Speakers (ON/OFF)
CONFIDENTIAL – DO NOT COPY
Page 3-2
File No. SG-0211
Page 11
C. TV：(Bold: Default)
a. Tuner Mode (Cable/Air)
b. Auto Search
c. Skip Channel
d. Digital Audio Out (PCM/Dolby Digital/OFF)
e. Time Zone (Eastern/Indiana/Central/Mountain/Arizona/Pacific/Alaska/Hawaii)
CONFIDENTIAL – DO NOT COPY
Page 3-3
File No. SG-0211
Page 12
D. Setup：(Bold: Default)
a. Language (English/ Français / Espaňol)
b. Sleep Timer (OFF/30Min/60Min/90Min/120Min)
c. Analog CC (OFF/CC1~4/TT1~4)
d. Digital CC (OFF/CC1~4/Service1~6)
e. Digital CC Style
1. Caption Style (As Broadcaster/Custom)
2. Size (Large/Small/Medium)
3. Font Color (White/Green/Blue/Red/Cyan/Yellow/Magenta/Black)
4. Font Opacity (Solid/Translucent/Transparent)
5. Background Color (White/Green/Blue/Red/Cyan/Yellow/Magenta/Black)
6. Background Opacity (Solid/Translucent/Transparent)
7. Window Color (White/Green/Blue/Red/Cyan/Yellow/Magenta/Black)
8. Window Opacity (Solid/Translucent/Transparent)
g. Rest All Setting (OK/Cancel)
CONFIDENTIAL – DO NOT COPY
Page 3-4
File No. SG-0211
Page 13
E. Parental：(Bold: Default)
Password (Default => 0000)
a. Cannel Block
b. TV Rating
c. Move Rating
d. Block Unrated TV (NO/Yes)
e. Access Code Edit
CONFIDENTIAL – DO NOT COPY
Page 3-5
File No. SG-0211
Page 14
RGB Mode
A. Picture Adjust：(Bold: Default)
a. Auto Adjust
b. Backlight (0~100, 90)
c. Contrast (0~100, 50)
d. Brightness (0~100, 50)
e. Color Temperature (6500/9300/Custom)
f. H-Size (0~255, 127)
g. H-Position (0~100, 65)
h. V-Position (0~100, 49)
i. Fine Tune (0~31, 17)
CONFIDENTIAL – DO NOT COPY
Page 3-6
File No. SG-0211
Page 15
B. Audio：(Bold: Default)
a. Volume (0~100, 25)
b. Bass (0~100, 50)
c. Treble (0~100, 50)
d. Balance (-50~50, 0)
e. Surround (ON/OFF)
f. Speakers (ON/OFF)
CONFIDENTIAL – DO NOT COPY
Page 3-7
File No. SG-0211
Page 16
D. Setup：(Bold: Default)
a. Language (English/ Français / Espaňol)
b. Sleep Timer (OFF/30Min/60Min/90Min/120Min)
c. Analog CC (OFF/CC1~4/TT1~4)
d. Digital CC (OFF/CC1~4/Service1~6)
e. Digital CC Style
1. Caption Style (As Broadcaster/Custom)
2. Size (Large/Small/Medium)
3. Font Color (White/Green/Blue/Red/Cyan/Yellow/Magenta/Black)
4. Font Opacity (Solid/Translucent/Transparent)
5. Background Color (White/Green/Blue/Red/Cyan/Yellow/Magenta/Black)
6. Background Opacity (Solid/Translucent/Transparent)
7. Window Color (White/Green/Blue/Red/Cyan/Yellow/Magenta/Black)
8. Window Opacity (Solid/Translucent/Transparent)
g. Rest All Setting (OK/Cancel)
CONFIDENTIAL – DO NOT COPY
Page 3-8
File No. SG-0211
Page 17
AV / COMPONENT MODE
A. Picture：(Bold: Default)
a. Picture Mode (Standard/Movie /Game / Custom)
b. Backlight (0~100, 90)
c. Contrast (0~100, 50)
d. Brightness (0~100, 50)
e. Color (saturation)(0~100, 50)
f. Tint (hue) (-32~32, 0)
g. Sharpness (0~7, 4)
h. Color Temperature (Cool/Normal/Warm/Custom)
CONFIDENTIAL – DO NOT COPY
Page 3-9
File No. SG-0211
Page 18
B. Audio：(Bold: Default)
a. Volume (0~100, 25)
b. Bass (0~100, 50)
c. Treble (0~100, 50)
d. Balance (-50~50, 0)
e. Surround (ON/OFF)
f. Speakers (ON/OFF)
CONFIDENTIAL – DO NOT COPY
Page 3-10
File No. SG-0211
Page 19
C. Setup：(Bold: Default)
a. Language (English/ Français / Espaňol)
b. Sleep Timer (OFF/30Min/60Min/90Min/120Min)
c. Analog CC (OFF/CC1~4/TT1~4)
d. Digital CC (OFF/CC1~4/Service1~6)
e. Digital CC Style
1. Caption Style (As Broadcaster/Custom)
2. Size (Large/Small/Medium)
3. Font Color (White/Green/Blue/Red/Cyan/Yellow/Magenta/Black)
4. Font Opacity (Solid/Translucent/Transparent)
5. Background Color (White/Green/Blue/Red/Cyan/Yellow/Magenta/Black)
6. Background Opacity (Solid/Translucent/Transparent)
7. Window Color (White/Green/Blue/Red/Cyan/Yellow/Magenta/Black)
8. Window Opacity (Solid/Translucent/Transparent)
g. Rest All Setting (OK/Cancel)
CONFIDENTIAL – DO NOT COPY
Page 3-11
File No. SG-0211
Page 20
D. Parental：(Bold: Default)
Password (Default => 0000)
a. Cannel Block
b. TV Rating
c. Move Rating
d. Block Unrated TV (NO/Yes)
e. Access Code Edit
CONFIDENTIAL – DO NOT COPY
Page 3-12
File No. SG-0211
Page 21
HDMI MODE
A. Picture：(Bold: Default)
a. Picture Mode (Standard/Movie /Game / Custom)
b. Backlight (0~100, 90)
c. Contrast (0~100, 50)
d. Brightness (0~100, 50)
e. Color (saturation)(0~100, 50)
f. Tint (hue) (-32~32, 0)
g. Sharpness (0~7, 4)
h. Color Temperature (Cool/Normal/Warm/Custom)
CONFIDENTIAL – DO NOT COPY
Page 3-13
File No. SG-0211
Page 22
B. Audio：(Bold: Default)
a. Volume (0~100, 25)
b. Bass (0~100, 50)
c. Treble (0~100, 50)
d. Balance (-50~50, 0)
e. Surround (ON/OFF)
f. Speakers (ON/OFF)
CONFIDENTIAL – DO NOT COPY
Page 3-14
File No. SG-0211
Page 23
C. Setup：(Bold: Default)
a. Language (English/ Français / Espaňol)
b. Sleep Timer (OFF/30Min/60Min/90Min/120Min)
c. Analog CC (OFF/CC1~4/TT1~4)
d. Digital CC (OFF/CC1~4/Service1~6)
e. Digital CC Style
g. Rest All Setting (OK/Cancel)
CONFIDENTIAL – DO NOT COPY
Page 3-15
File No. SG-0211
Page 24
[INPUT]
“INPUT” could supply an interface providing a list. The list shows input sources and
provides the choices of different sources. The list includes items as below:
A. TV: Analog TV or digital TV
B. AV1, AV2: Composite (AV) signal
C. Component1, Component2: Color difference (YPbPr) video signals.
D. RGB: Video Graphics Array (VGA) or D-sub video signals.
E. HDMI1, HDMI2: High Definition Multimedia Interface (HDMI) multimedia signals.
Note： The list of PIP provides the choices of different sources on sub-screen.
[INFO]
“INFO” button could show an information bar which displays the information about the
input signal on our LCD TV.
CONFIDENTIAL – DO NOT COPY
Page 3-16
File No. SG-0211
Page 25
Chapter 9 Trouble shooting
(
MONITOR DISPLAY NOTHING (PC MODE)
Start
LED is lighted
Orange)
N0
1. Is Power board output
+5V(F2)?
2. Is J1 connector good?
3. Is DC-DC OK?
4. Is U8 pin2 (3.3V) working ok?
LED is lighting?
Is backlight on?
Yes
Yes
N0
N0
N0
It is in power saving
1. Check video cable
2. Is the timing supported?
3. Check sync input
4. Check VGASOG rout if analog
(SOG) (C88)
1.Check J1 PIN 13 (5V)
2.Is inverter ok?
3.Is Power Board ok?
Yes
Yes
U11has no data
out?
Yes
END
CONFIDENTIAL – DO NOT COPY
N0
It means data to LVDS
1. Is J7 connecting OK?
2. Check J1 +5V (F2) & +12V (F1)
3. Is panel ok?
Check P3 D-sub Input correct
4.
5. Check analog input route
Page 9-1
File No. SG-0211
Page 26
(TV,
COMPOSITE VIDEO1, 2, S-VIDEO) IS NOT DISPLAY CORRECTLY
Star t
N0
Input signal good?
1. Check video
2. Check DVD player
Yes
U4 input correct?
Yes
LVDS output correct?
Yes
1.Chcak J5 Connect is good?
2.Is panel working ok?
END
N0
N0
1. Check P11&J4 signal
2. Check signal between P2 and U4
(IF AV1/AV2 mode)
3. Check Tuner &U4 (IF TV mode)
4. Check J4 (IF S-Video)
5. Check U4 POWER +3.3V
1.Check LVDS LINE
2.Check U4 clock (27MHz)(X1)
3.Check U4 power
CONFIDENTIAL – DO NOT COPY
Page 9-2
File No. SG-0211
Page 27
(COMPONENT1,
2) IS NOT DISPLAY CORRECTLY
Star t
N0
Input signal good?
Yes
N0
P4 input correct?
Yes
N0
U11 input correct?
1. Check video
2. Check host’s setting
1. Check signal from P1
2. Check system power 12V& 5v
1. Check signal between U4&P1
2. Check X1 Clock (27MHZ)
Yes
Is LVDS output
correct ?
Yes
1 .Is J7 connected good?
2. Is panel working ok?
END
N0
1. Check U4
2. Check U4 power 3.3V&1.25v&1.8v
CONFIDENTIAL – DO NOT COPY
Page 9-3
File No. SG-0211
Page 28
HDMI) IS NOT DISPLAY CORRECTLY
(
Star t
Input signal good?
N0
1. Check video
2. Check host’s setting
U11 no data out ?
U31 input correct?
1.Is J2 connected good?
2.Is panel working ok?
Yes
Yes
Yes
Yes
N0
N0
1. Check p6&p7 connect
2. Check the pin18 & 19 of P6 & P7
3. Check the pin 6 of U23 & U25
1. Check U11 power
2 Check between signal U19
and U11
3. Check U19 clock 27MHZ
END
CONFIDENTIAL – DO NOT COPY
Page 9-4
File No. SG-0211
Page 29
TROUBLE
OF DC-DC CONVERTER
Star t
J1 PIN10,11,12
Yes
J1 PIN 2,3,4,5
Yes
U1 pin 5 6 7 8
N0
N0
N0
The voltage is about + 5V
1. Check power board
2. Check power cable, F2 & connection J1
3. Check U8 pin1 (+5V) & pin2 (+3.3V)
The voltage is about + 12V while power switch on
1. Is J1 connection good
2. Check J1 Pin1 is up to about 3.3V?
3. Check power board
4. Check F1.
The voltage is about +5V while power switch on
1. Check F2 & U1
2. Check OPWRSB (R20)
3. Check U1 pin1&2 or pin 3&4, should have -1V more.
U2, U4 & U33 pin2
U6 pin 2
U5 pin2
U10 pin2
U3 pin1 & pin2
Yes
Yes
Yes
Yes
N0
N0
N0
N0
The voltage is about +3.3V
1. Check F2 & U1
2. Check U2, U4 & U33
The voltage is about +1.8V
1. Check F2 & U1
2. Check U6
The voltage is about +1.2V while power switch on
1. Check F2 & U1
2. Check U5
The voltage is about +2.6V while power switch on
1.Check J1 Connect
2.Check U10
The voltage is about +12V to +5V(for Tuner)while
power switch on
1. Check F1
2. Check U3 pin1 (+12V) & U3 pin2 (+5V)
END
CONFIDENTIAL – DO NOT COPY
Page 9-5
File No. SG-0211
Page 30
TROUBLE
OF EDID READING
Star t
Is Analog DDC OK?
Yes
Is HDMI DDC OK?
Yes
N0
Support DDC1/2B
1. Analog cable ok?
2 .Check signal (U21 to P3)
3. Check U21 Voltage
4. Is protocol compliant?
N0
Support DDC1/2B
1. Analog cable ok?
2. Check signal (U23 to P6)
3. Check signal (U25 to P7)
4. Is protocol compliant?
END
CONFIDENTIAL – DO NOT COPY
Page 9-6
File No. SG-0211
Page 31
Page 32
Page 33
Loading...