VEGA MET514V User Manual

Menu plan
VEGAMET 514V
TAG ­No. 1 % 12,3
%
100
-
Level and Pressure
+
ESC
OK
CONNECT
513
out
in
Reduced menu
For adjustment of the signal conditioning instruments VEGAMET 514 V two menus are available: the „Reduced menu“ and the „Extended menu“ (see following pages).
As factory setting „Reduced menu“ is activated. The most important adjustment steps (e.g. adjustment, adjustment integration time, simulation...) can be carried out in the „Reduced menu“.
When you want to move to the „Extended menu“ (e.g. to edit linearisation curves) proceed as follows:
– Move with the OK-key and the arrow keys to the menu point „Menu mode reduced“. – Push the + key twice. – The display shows now „Menu mode extended“. – Now push the OK-key to save the adjustment.
In white letters
Lang-
you see the
uage
parameters which
Eng-
can be modified
lish
and which can be saved with the OK-key.
with the + or - key
ESC
OK
Bolt print / italic are
Param.
the sensor or
TAG-
measured value
No. 1
information which
Relay outp. 2
cannot be
Light grey menu points are only displayed if necessary (dependent on the adjustments in other menus).
modified in this position.
With these keys you move in the menu field
2 VEGAMET 514V
Reduced menu
TAG­No. 1 % xx,x
Param.
TAG­No. 1
Adjust ment
TAG­No. 2 °C xx,x
Confi­gura­tion
Sensor type
Hydro static
The sensor type can be only modified when „Reset TAG 1“ had been carried out before.
Signal condit­ioning
Sca­ling
Measured
TAG1-2
value indication
xx,x xx,x
Add’l func­tions
Pass-
Lang-
word
uage
Eng­lish
off
TAG-ID
Sensor opti­mize
TAG ­No. 1
Sensor menu
(see operating
instruction of the
sensor)
Out­puts
mA
mA
outp. 1
outp. 2
4/
4/
20mA
20mA
Integr ation time s 0
TAG 1 to De­fault
Reset
OK ?
Reset Now !
OK ?
Volt outp. 1
0/10V
Reset TAG1
Delete TAG 1?
Volt outp. 2
0/10V
Reset
OK?
Reset Now!
OK?
Relay out­put 1
Mode
Over­fill protec
Menu mode
Re­duced
Relay out­put 2
like Rel.-outp.1
Low
% 0,0
High
% 100,0
Simu­lation
Simu­lation Now OK ?
Simu­lation % xx,x
with medium
Min adjust at % 0,0
0% corres ponds 0
Max adjust at % 100,0
100% corres ponds
1000
Deci­mal­point
888,8
w.out medium
adjust ment
bar
Prop. to
unde­fined
0% at bar 0,000
Unit
– –
100% at bar 5,000
VEGAMET 514V 3
TAG ­No. 1 % xx,x
Param.
TAG­No. 1
Adjust ment
TAG ­No. 2 °C xx,x
Param.
TAG­No. 2
like TAG-No.1
Signal condit ioning
TAG1-2
xx,x xx,x
Out­puts
mA out­puts
Measured value indication
Volt. out­puts
Extended menu
MET-
Relay
Dis-
out-
play
puts
with medium
Min adjust at % 0,0
Sca­ling
0% corres ponds 0
Max adjust at % 100,0
mA output no.1
Prop. to
Per­cent
LIN­curve
linear
100% corres ponds 1000
Volt. output no.1
mA output no.2
w.out medium
Volt. output no.2
Unit
Prop. to
Per­cent
0,0%
like mA-output no.1
Unit
mA output
0,0%
4/ 20mA
Densi-
Integr
ty in
ation
Kg/dm3
time s
1,000
0
Prop.
Deci-
to
mal-
unde-
point
fined
888,8
adjust
Offset
ment
correc tion
bar
Sensor unpres sur’d OK ?
Offset corr. Now ! OK ?
like Volt-output no.1
Volt.
Volts
output
at 0%
0/10V
0,000
mA at 0%
4,000
Unit
– –
0% at bar
0,000
mA at 100%
20,000
100% at bar
1,000
Volts at 100%
10,000
Meas. value limita tion
nega­tive Values yes
Fail­ure mode
0mA
Fail­ure mode
0V
Fail. mode
Stan­dard
mA limita tion
on
Volt­limita tion
on
Relay out­put 1
Prop. to
Per­cent
Prop. to
Per­cent
Relay out­put 2
like Relay output 1
Unit
0,0%
Unit
0,0%
Mode
Over­fill protec
4 VEGAMET 514V
Extended menu
DIS-
PC/
out-
DCS
puts
out­puts
Simu­lation
Simu­lation Now! OK?
Simu­lation %
XX,X
Spe­cial funct.
Reset
level
Reset
OK ?
Reset Now!
OK ?
Real value corr. % 0
Densi­ty corr. % 0
Manual correc tion
Offset correc­tion
Offset correc­tion OK?
Real value corr.
Real value corr. OK?
continued —>
DCS out­put 1
Prop. to
Per­cent
Monit. on
Low& High
DIS­outp.1
Prop. to
Per­cent
DCS out­put 2
Unit
0,0%
Low
% 0,0
DIS­outp.2
like DIS-outp.1
Unit
0,0%
DCS out­put 7
High
% 100,0
DIS­outp.7
like DCS output1
Deviat ion % 1,0
Deviat ion period
Scan time s 1
Fail­ure mode off
No. of Scans 10
Correc tion Now ! OK ?
Add’l func­tions
Switch ing delay
t on
s 0
Correc tion at % 0,0
Correc tion Now! OK ?
t off
s 0
ESC
OK
With these keys you move in the menu field
Sensor­type
hydro­static
Lang­uage
Eng­lish
mA at 100%
20,000
Bolt print / italic are the sensor or measured value information which cannot be modified in this position.
In white letters you see the parameters which can be modified with the + or - key and which can be saved with the OK-key.
Light grey menu points are only displayed if necessary (dependent on the adjustments in other menus).
VEGAMET 514V 5
< previous page
Confi­gura­tion
Extended menu
Config Inputs
*) *) *) *)
*)
Input no. 1
Config
Config
out-
Meas.
puts
loop
Config curr. output
mAno.1 to
TAG ­No. 1
TAG 1
TAG 2
level
tempe­ratur
TAG-ID
TAG ­No. 2
Appli­cation
level
Sensor type
Hydro­static
The parameters in these menu points can be only modified when „Reset to single measurement“ had been carried out first.
Input no. 2
Config volt. output
V no.1 to
TAG ­No. 1
mAno.2 to
TAG ­No. 2
Fault signal ?
on
Mode
Stan­dard
Config relay output
Operat ing relay
V no.2 to
TAG ­No. 2
Rel. 1 to
TAG ­No. 1
Tar e Moni-
Option
no option
like TAG 1
toring
Sensor coordi nation
Locai­tion A
input no. 1
Fail safe relay
Relay
Stan­dard
Rel. 1
Stan­dard
TAG-ID
TAG ­No. 1
Locai­tion D
unde­fined
Config PC/ DCS output
PC/ DCS Meas. values
DCS 1 to
TAG ­No. 1
Input
unde­fined
Fault signal ?
on
Input no. 4
Locai­tion E
unde­fined
Config VEGA­DIS
DIS 1 to
TAG ­Nr. 1
PC/ DCS Relay status
off
DCS 2 to
- - --
Rel. 2 to
TAG ­No. 2
DIS 2 to
- ---
PC/DCS Input status
off
DCS 7 to
- -- -
Rel.2
Stan­dard
Tar e Moni-
Input from
unde­fined
DIS 7 to
- ---
Input
unde­fined
toring
Input from
unde­fined
like Input no.1
Input from
local MET
Serial no.
xxxx xxxx
Input no.
unde­fined
Sensor charac terist ics
Min. meas. range 0,00
Max. meas. range 5,00
Sensor opti­mize
Sensor menu
(see operating
instruction of the
sensor)
Input from
local MET
Chan­nel no. K1
Input no.
unde­fined
6 VEGAMET 514V
Extended menu
continued —
ESC
OK
With these keys you move in the menu field
>
Sensor­type
hydro­static
Lang­uage
Eng­lish
mA at 100%
20,000
Bolt print / italic are the sensor or measured value information which cannot be modified in this position.
In white letters you see the parameters which can be modified with the + or - key and which can be saved with the OK-key.
Light grey menu points are only displayed if necessary (dependent on the adjustments in other menus).
VEGAMET 514V 7
< previous page
Add’l func­tions
Extended menu
Pass­word
off
Edit lin. curves
Curve no.1
Info Lang-
Input Info
Input no. 1 VBUS
Curve no.2
VEGA­MET info
Type MET 514 V
Sensor menu
(see operating
instruction of the
sensor)
Curve no.3
like curve no.1
Pro­gram info
Pro­gram info
xxxxxx
Serial number xxxx
xxxx
Input no. 2 VBUS
Meas. loop info
TAG 1
TAG ­Nr. 1
MIN adjust at% 0,0
Instr. addr.
1
like input no. 1
TAG 2
TAG ­Nr. 2
MIN adjust bar
0,000
Softw. Vers.
XX.XX XX
Input no. 4
Sensor­type
Vibra­tion
like TAG 1
uage
Eng­lish
MAX adjust at% 100,0
Softw. Date
XX/XX
Input from
local MET
MAX adjust bar
1,000
Param. Vers.
X
Chan­nel no. K1
Para­meter
level
Actual switch status
Add Lin.­point
x % 0,0 y V% 0,0
Edit curve no.1
x 0 %
0,0
y 0 V% 0,0
x 1 %
x 2 %
100,0
100,0
y 1 V%
y 2 V%
100,0
100,0
Index marker numbers (0...32)
x32 %
100,0
y32 V% 100,0
Delete Lin.­point
x 0,0 y 0,0
delete
delete Now?
x100,0 y100,0
delete
delete Now?
8 VEGAMET 514V
Extended menu
Reset VEGA­MET
Reset Confi­gura­tion
TAG 1 to De­fault
Reset
OK?
Reset Now!
OK?
Reset Sensor charac
TAG 2 to De­fault
Reset
OK?
Reset Now!
OK?
Reset lin. curves
Reset curve no.1
Reset
OK?
Reset Now
OK?
to single meas.
Reset TAG 1
Delete TAG 1?
Ser­vice
only accessible with service password
Reset
Reset
curve
curve
no.2
no.3
Reset
OK?
Reset Now!
OK?
Reset TAG 2
Delete TAG 2?
Reset
OK?
Reset Now!
OK?
Menu mode
Exten­ded
Reset all curves
Delete all curves
Reset
OK?
Reset Now!
OK?
Sensor­type
hydro­static
ESC
OK
With these keys you move in the menu field
Bolt print / italic are the sensor or measured value information which cannot be modified in this position.
Reset
OK?
Reset Now!
OK?
Reset
OK?
Reset Now!
OK?
Lang­uage
Eng­lish
mA at 100%
20,000
In white letters you see the parameters which can be modified with the + or - key and which can be saved with the OK-key.
Light grey menu points are only displayed if necessary (dependent on the adjustments in other menus).
VEGAMET 514V 9
Notes
10 VEGAMET 514V
Notes
VEGAMET 514V 11
VEGA Grieshaber KG Am Hohenstein 113 D-77761 Schiltach Phone (0 78 36) 50 - 0 Fax (0 78 36) 50 - 201 e-mail vega@vega-g.de
ISO 9001
Technical data subject to alterations 2.22 278 / Jan 98
Loading...