Vaddio Quick-Connect 4 User Manual

Camera and Electronic Products for Integrators
Quick-Connect™ 4
Video, Power and Control Wiring Center
Figure 1:
Vaddio Quick-Connect 4 Video, Power and Control Wiring Center
Front Panel (above) and Back Panel (below) shown
INTRODUCTION
INTENDED USE
SAVE THESE INSTRUCTIONS
IMPORTANT SAFEGUARDS
Each camera port has an individual 18VDC supply to power a single PTZ camera. Power is provided to the camera and S-Video and Composite video are both returned to the Quick-Connect 4 on the same single Cat. 5 cable for Power/Video.
Individual control ports are supplied for camera control systems like the ProductionVIEW™ and camera control daisy chaining is accommodated through the first camera control port as well.
Control inputs are either DB-9 or RJ-45 and control outputs are RJ-45, which connect easily with all Vaddio WallVIEW™, CeilingVIEW™, EZCamera and HideAway series cameras.
Before operating the Vaddio Quick-Connect 4, please read the entire manual thoroughly. The wiring system was designed, built and tested for use indoors. Outdoor operation is not recommended, has not been tested and could damage the unit and/or create a potentially unsafe operating condition. Use only the Vaddio provided power supply.
The information contained in this manual will help you install and operate your Vaddio Quick-Connect 4. For reference, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product drawings for the Vaddio product line on the website. These documents can be downloaded from
www.vaddio.com
free of charge.
Read and understand all instructions before using. Do not operate the device if it has been dropped or damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.
Installation and User Guide
Vaddio Quick-Connect 4 - Document 341-256-1 Rev C
Quick-Connect 4
UNPACKING
INSTALLATION
Compatible Camera Systems
Use only the power supply provided with the Quick-Connect 4 Wiring Center. Use of any unauthorized power supplies will void any and all warranties.
Carefully remove the device and all of the parts from the packaging.
Unpack and identify the following parts:
One (1) Quick-Connect 4 Wiring Center (rack mount)
One (1) 18VDC, 5.5Amp, 100W PowerRite Power Supply
Installation and User Guide (341-256-1)
The Quick-Connect 4 was specifically designed for simplifying the installation of camera systems using the Vaddio Cat. 5 cabling scheme for distribution of Video
(both S-Video and Composite video) and Power on the same Cat. 5 cable with
Control handled on a second Cat. 5 cable which adheres to both the Sony and Canon Daisy chain wiring convention for control of multiple cameras with a single control port. Below is a list of compatible Vaddio Camera Systems using the Vaddio wiring standard.
The Quick-Connect 4 is compatible with the following Vaddio cameras and Camera Systems:
Vaddio WallVIEW 100
Vaddio WallVIEW 70
Vaddio WallVIEW 50i
Vaddio CeilingVIEW 70 PTZ
Vaddio CeilingVIEW 70 PTZ HideAway*
Vaddio CeilingVIEW 50iR PTZ
Vaddio WallVIEW 50i PTZ HideAway*
EZCamera PTZ Series Camera Kit (Camera, Cat. 5 Shoe and Remote)
Vaddio Model 100 PTZ
Vaddio Model 70 PTZ
Vaddio Model 50 PTZ
Vaddio Model 50iR PTZ
*Note: Due to the power requirements for proper operation, the Quick-Connect 4 can supply
power to only two (2) of the HideAway products (Ceilin gVIEW 70 PTZ Hide Away and WallVIE W 50i PTZ HideAway) at any given time.
Controls, Inputs and Outputs (Camera 1)
A
Figure 2: Back Panel Connections
A) Power Input (18V, +center, 5.5A) Supports up to Four (4) PTZ Cameras B) Video/Power Connection – Carries Power to the camera and returns S-Video and
C) S-Video Output of Camera on 4-pin mini din D) Composite Video Output of Camera on BNC E) Control Through Output Port to Camera (RS-232 on Cat. 5 cable) F) Control Through Input Port from Controller (RS-232 on Cat. 5) G) Control Through Input Port from Controller (RS-232 on DB-9)
Composite Video to the Quick-Connect 4
Vaddio Quick-Connect 4 - Document 341-256-1 Rev C
C
B
D E
Page 2 of 8
G
F
Quick-Connect 4
BASIC CAMERA
CONNECTION
4-Camera Daisy Chain Control Example (1-Control Port)
ControlVIEW Xtreme & Quick-Connect 4
Figure 3: Single Camera Connection
Power to Camera, S-Video and Composite Video from Camera over Single Cat. 5
Power Supply
Figure 4: Daisy Chain Example with Single Control Port
Cam 1
Power & Video Power & Video
Cat. 5
Power
Camera 1
S-Video
Output
S-Video
Output
RS-232
Cat. 5
OUT
RS-232
Camera 3
S-Video
Output
RS-232 on Cat. 5
RS-232 from
Controller
Composite
Video
DB-9 or RJ-45
Output
RS-232
Cat. 5 Cat. 5
Cam 2
Cat. 5 Cat. 5
RS-232 DB-9 to DB-9
Camera 4
S-Video
Cat. 5
OUT
Power & Video
Vaddio ControlVIEW Xtreme
Vaddio Model 100 PTZ with Camera Shoe
RS-232
OUT
Cam 3
Power & Video
Camera 2
S-Video
Output
Output
Cam 4
Cat. 5
Vaddio Quick-Connect 4 - Document 341-256-1 Rev C
Page 3 of 8
Quick-Connect 4
4-Camera Direct Control Example (4-Control Ports)
ProductionVIEW
&
Quick-Connect 4
4-Camera Quick-Connect 4 Head End Daisy Chain Example (1-Control Port)
Note: Cat. 5 Cable Maximum Length for this Control Configuration: 50’/15.24m
Power & Video
Figure 5:
Vaddio ProductionVIEW FX (6 discrete control ports ­no daisy chain control)
3-Cat.5 Homeruns
Figure 6: Head End Daisy Chain Example (see Figure 7 for I/O detail)
Cat. 5
Cat. 5
Cam 1 S-Video
RS-232
Power & Video
RS-232
Cam 3 S-Video
RS-232 Cat. 5
Cat. 5
Cam 2 S-Video
3-Cat.5 Homeruns
Power & Video
Cat. 5
Cat. 5
Cam 4 S-Video
RS-232
Cat. 5
Power & Video
RS-232
Control Source
2-Cat.5 Homeruns
Vaddio Quick-Connect 4 - Document 341-256-1 Rev C
Page 4 of 8
Quick-Connect 4
4-Camera Quick-Connect 4 Head End Daisy Chain Example Detail
Note: Cat. 5 Cable Maximum Length for this Control Configuration: 50’/15.24m
PIN-OUTS
Video/Power
Figure 7: Connection Detail for Head End Daisy Chain using the Quick-Connect 4
Control Source ControlVIEW Xtreme
Camera 1 Vaddio Model 100 PTZ
Camera 2 Vaddio Model 100 PTZ
3-Cat.5 Homeruns
3-Cat.5 Homeruns
Control to Camera
Control Out to QC4
Control to Camera
Control Out to QC4
Camera 3 Vaddio Model 100 PTZ
3-Cat.5 Homeruns
Control to Camera
Control Out to QC4
Camera 4 Vaddio Model 100 PTZ
2-Cat.5 Homeruns
Control to Camera
The pin-outs for the Quick-Connect 4’s Video, Power and Control connectors are as follows:
Video/Power Connection RJ-45
RJ-45 Pins
1) Power (+)
2) Power GND
3) Video GND
4) Y (luminance)
5) Video GND
6) C (Chrominance)
7) Video GND
8) Composite Video
12345678
Video/Power
Top
View
Vaddio Quick-Connect 4 - Document 341-256-1 Rev C
Page 5 of 8
Quick-Connect 4
Control Inputs
Control Output
to Camera
CARE AND CLEANING
OPERATING AND STORAGE CONDITIONS
Control Input Connections RJ-45 and DB-9F
RJ-45 Pins
1) DTR
2) DSR
3) CTS
4) RTS
5) Unused
6) Digital GND
7) RXD
8) TXD
DB-9 Pins
2) Through to Pin 8 (TXD)
3) Through to Pin 7 (RXD)
5) Through to Pin 6 of RJ-45
(Sony* Daisy chain to DSR) (Sony* Daisy chain from DTR) (Canon Daisy chain to RTS) (Canon Daisy chain from CTS)
(from TXD of control source) (to RXD of control source)
12345678
Control Inputs
*DTR/DSR also applies to Canon VCC-50i Products featuring Vaddio’s exclusive VISCA Control Translation
5 1
Control Output Connection RJ-45
RJ-45 Pins
1) DSR (Sony* Daisy chain from DTR)
12345678
2) DTR (Sony* Daisy chain to DSR)
3) RTS (Canon Daisy chain from CTS)
Control Out
4) CTS (Canon Daisy chain to RTS)
5) Unused
6) Digital GND
7) TXD (to RXD of control source)
*DTR/DSR also applies to Canon VCC-50i Products featuring Vaddio’s exclusive VISCA Control Translation
8) RXD (from TXD of control source)
Do not attempt to take the Quick-Connect 4 apart. There are no user­serviceable components inside. Disassembly of the device will void the warranty.
Do not spill liquids onto the device
Keep this device away from food and liquid
For smears or smudges, clear any dust with a blower and wipe
stains with a clean, soft cloth. Do not use any abrasive chemicals.
Do not store or operate the Quick-Connect 4 under the following conditions for any circumstance:
Temperatures above 40°C (104°F)
Temperatures below 0°C (32°F)
High humidity, condensing or wet environments
Dusty environments
In inclement weather
Under severe vibration
Vaddio Quick-Connect 4 - Document 341-256-1 Rev C
Page 6 of 8
Quick-Connect 4
GENERAL SPECIFICATIONS
WARRANTY INFORMATION
Camera Ports: Control Through Ports:
Power Supply: Video Output Connections:
Size:
Weight:
4-Individual RS-232 2-inputs on RJ-45F and DB9F per camera 1-output on RJ-45F per camera 18 VDC, 5.5 Amp, 100W S-Video out on 4-pin mini din & Composite Video Out on BNC (Both signals are live) 2-Space Rack Mount Height - 3.5” (8.89cm) 4” (10.16cm) Deep
2.2 lbs, 1kg
Hardware* Warranty - One year limited warranty on all parts. Vaddio warrants this product
against defects in materials and workmanship for a period of one year from the day of purchase if Vaddio receives notice of such defects during the warranty. They will, at its option, repair or replace products that prove to be defective.
Exclusions - The above warranty shall not apply to defects resulting from: improper or
inadequate maintenance by the customer, customers applied software or interfacing, unauthorized modifications or misuse, operation outside the normal environmental specifications for the product, use of the incorrect power supply, or improper site operation and maintenance.
Vaddio Customer service – Vaddio will test, repair, or replace the product or products
without charge if the unit is under warranty. If the product is out of warranty, Vaddio will test then repair the product or products. The cost of parts and labor charge will be estimated by a technician and confirmed by the customer prior to repair. All components must be returned for testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.
Vaddio Technical support - Vaddio technicians will determine and discuss with the
customer the criteria for repair costs and/or replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at support@vaddio.com or online at www.vaddio.com
Return Material Authorization (RMA) number - Before returning a product for repair or
replacement request an RMA from Vaddio’s technical support. Provide a technician with a return phone number, e-mail address, shipping address, and product serial numbers. Describe the reason for repairs or returns as well as the date of purchase. Include your assigned RMA number in all correspondence with Vaddio. Write your assigned RMA number on the outside of the box when returning the product.
Voided warranty – The warranty does not apply if the original serial number has been
removed or if the product has been disassembled or damaged through misuse, accident, modifications, or unauthorized repair.
Shipping and handling - Vaddio will not pay for inbound shipping transportation or
insurance charges or accept any responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and insurance charges all items under warranty but will not assume responsibility for loss and/or damage by the outbound freight carrier. If the return shipment appears damaged, retain the original boxes and packing
material for inspection by the carrier. Contact your carrier immediately. Products not under warranty - Payment arrangements are required before outbound
shipment for all out of warranty products.
*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry standard practices.
.
Vaddio Quick-Connect 4 - Document 341-256-1 Rev C
Page 7 of 8
Quick-Connect 4
9433 Science Center Drive, New Hope, MN 55428
Toll Free: 800-572-2011 Phone: 763-971-4400 FAX: 763-971-4464
www.vaddio.com
©2006 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Quick-Connect, CeilingVIEW, EZCamera, ControlVIEW, WallVIEW and PowerRite are registered trademarks of Vaddio. All other trademarks are property of their respective owners. Document 341- 256-1 Rev C
Vaddio Quick-Connect 4 - Document 341-256-1 Rev C
Page 8 of 8
Loading...