Installation and User Guide
VADDIO™ POWERVIEW™ HD-22 QCCU
AND HD-30 QCCU SYSTEMS
Featuring the Quick-Connect Universal CCU
PowerVIEW HD-22 QCCU Systems
Part Numbers:
999-6967-000: North America
999-6967-001: International
PowerVIEW HD-30 QCCU Systems
Part Numbers:
999-6977-000: North America
999-6977-001: International
Universal CCU for HD-22 or HD-30 (shown without Rack Ears)
EZIM™ Slot Card Interface
Part Number: 998-6700-006
© 2015 Vaddio - All Rights Reserved. Document Number 342-0645 Rev F
PowerVIEW HD-22/30 QCCU System
Inside Front Cover - Blank
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 2 of 28
PowerVIEW HD-22/30 QCCU System
Table of Contents
Overview .................................................................................................................................................................... 4
Intended Use .......................................................................................................................................................... 4
Important Safeguards ............................................................................................................................................ 4
Save These Instructions ........................................................................................................................................ 4
Unpacking .................................................................................................................................................................. 5
PowerVIEW HD-22 QCCU ................................................................................................................................. 5
PowerVIEW HD-30 QCCU ................................................................................................................................. 5
Anatomy of the HD-22 and HD-30 ............................................................................................................................. 6
Image: PowerVIEW HD-22/30 HD PTZ Camera ............................................................................................... 6
Image: PowerVIEW HD-20 or HD-30 HD PTZ Camera (Rear Panel) .............................................................. 7
First Time Set-up with the PowerVIEW HD-22 or HD-30: ......................................................................................... 8
Image: PowerVIEW HD-22/30 Rear Panel Connections .................................................................................. 8
Drawing: Dip Switch and Resolution Label on the Bottom of the HD-22/30 ..................................................... 8
Anatomy of the Quick-Connect Universal CCU ......................................................................................................... 9
Image: Quick-Connect Universal CCU HD-22/30 Front Panel Controls ........................................................... 9
Image: Close up View of the Universal CCU HD-22/30 Control Panel ............................................................. 9
Image: Rear Panel CCU Connections and Controls (left to right) ................................................................... 10
The EZIM (EZ Interface Module) HD-Series Slot Card........................................................................................ 10
Image: EZIM Slot Card .................................................................................................................................... 10
The HD-22 and HD-30 Control Menu Screens ........................................................................................................ 11
Image: Menu Organization HD-22/30 ............................................................................................................. 11
Installation Basics: ................................................................................................................................................... 13
General Installation Instructions for the CONCEAL Wall Mounting System: ....................................................... 13
Drawing: Basic System Connectivity ........................................................................................... .................... 15
Optimizing System Performance: ............................................................................................................................ 16
General Specifications: ............................................................................................................................................ 17
Warranty Information: .............................................................................................................................................. 18
Compliance and CE Declaration of Conformity - PowerVIEW HD-22 and HD30 ................................................... 19
Compliance and CE Declaration of Conformity - Universal CCU and EZIM CCU .................................................. 20
Appendix 1: Cable Pin-outs for the Quick-Connect CCU System .......................................................................... 21
Table: New Commands for the CCU Scene Selection ................................................................................... 22
Appendix 2: PowerVIEW EZ-Power Video RJ-45 Connector Pin-outs ................................................................... 23
Drawing: PowerVIEW HD-22/30 Dimensions ................................................................................................. 23
Appendix 3: Communication Specification ............................................................................................................. 24
HD-22/30 Command List (1/2) ......................................................................................................................... 24
HD-22/30 Command List (2/2) ......................................................................................................................... 25
HD-22/30 Inquiry List (1/1) ............................................................................................................................... 26
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 3 of 28
PowerVIEW HD-22/30 QCCU System
Overview
The WallVIEW Universal CCU system for the PowerVIEW HD-22 and PowerVIEW HD-30 HD
Pan/Tilt/Zoom Camera Systems includes the HD-22 or HD-30 PTZ camera, the Quick-Connect™
Universal CCU, matching CONCEAL™ camera mount, EZIM CCU Slot Card and accessories
(mounting hardware, control adapter).
The Vaddio PowerVIEW HD-22 and HD-30 high definition PTZ cameras are available with 22X and 30X power zoom optics
respectively. With a 1/2.8-Type, progressive scan 1MOS image sensor, the cameras allow for better light sensitivity, increased
noise reduction and lower power consumption. T his advanced MOS image sensor provides for delicate gradation, realistic
textures and vivid colors that are comparable to 3-chip camera performance.
The HD-22 has a powerful 22X multi-element glass zoom l ens (f=4.3mm to 94.6mm) and works exceptionally in large rooms.
However, the premium optics also provides a wide horizontal field of view of 65.2º, which works very well in small room video
applications. The HD-30, as the name would suggest, has a robust 30X optical power zoom lens that enables the capture of
brilliant and detailed video images even in the largest rooms. The cameras output multi-format HD video in both analog
component (YPbPr), HDMI and differential formats in HD resolutions of 1080p/59.94, 1080p/50 1080p/29.97 1080p/25,
1080i/59.94, 1080i/50, 720p/59.94, 720p/50 and SD resolutions of 480p/59.97 an d 576p/50.
These systems pair the Quick-Connect Universal CCU with the HD-22/30. The Universal CCU Cat-5 uses HSDS™ (high speed
differential signaling), an active video transmission system, to deliver high qua lity HD video over standard Cat-5 cabling up to
500’ (152.4m) with virtually no loss in video quality and no latency. O ne of the most flexible attributes the Universal CCU is at
the outputs. It has HD-SDI or SDI outputs (yep, even 3 Gb/s single link HD-SDI for 1080p/59.94), HDMI and HD Analog
component (YPbPr) outputs, all of which can be used concurrently (at the same resolution). Available resolutions range from
480i up to and including 1080p/59.94 on all outputs. The Universal CCU has an attractive industrial design that also simplifies
the operation of the CCU. The back-lit blue LED screen displays up to eight (8) parameters at a time, as well as the camera’s
model number so the interrelationship of the controls is easily and quickly read and understood.
The Universal CCU series for PowerVIEW HD-22 and HD- 30 allows the user to adjust auto AWB or Manual Red and Blue Gain,
OPWB, Iris functions, Gain, Chroma, Pedestal, Detail, and Gamma on the cameras. These controls allow the camera to deliver
a more accurate representation of the captured image’s color. Other added advantages include the ability to color match multiple
cameras and eliminate the need to use automatic exposure and color settings.
Overall, any WallVIEW System using the Quick-Connect Universal CCU is superb for a wide range of serious, high definition
shooting applications. It is also great where adjusting the color and brightness levels of one or multiple cameras is critical, as in
houses of worship, corporate boardrooms, live event production and distance-learning applications.
Intended Use
Before operating the device, please read the entire manual thoroughly. The system was designed, built and tested for use
indoors, and with the provided power supply and cabling. The use of a power supply other than the one provi ded or outdoor
operation has not been tested and could damage the device and/or create a potentially unsafe operating condition.
Important Safeguards
Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged. In this case,
a Vaddio technician must examine the product before operating. T o reduce the risk of el ectric shock, do not immerse in water
or other liquids and avoid extremely humid conditions. Do not connect Power over Ethernet (PoE) cables directly to the RJ-45
ports on the device as damage may result.
Use only the power supply provided with the system. Use of any unauthorized
power supply will void any and all warranties.
Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not work
well for professional installations and can be the cause of intermittent connections which can result in
the RS-232 control line failing and locking up. For best results please use standard RJ-45 connectors
and test all cables for proper pin-outs prior to use. Mark all cables to avoid errant connections.
Save These Instructions
The information contained in this manual will help you install and operate the product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation & User Guides and most pertinent product drawings
for the Vaddio product line on the Vaddio website.
PowerVIEW
HD-22 or HD-30
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 4 of 28
PowerVIEW HD-22/30 QCCU System
Unpacking
Carefully remove the device and all of the parts from the packaging. Unpack and identify the following parts:
PowerVIEW HD-22 QCCU
Part Number: 999-6967-000, North America
One (1) Vaddio PowerVIEW HD-22PTZ Camera (998-6960-000)
One (1) Universal CCU Cat-5 for HD-22 or HD-30 with Rack Ears
One (1) 36 VDC Switching power supply with power cord for North America
One( 1) 2-pin Phoenix-type 5.0mm Euro style connector (for Tally LED)
One (1) EZIM CCU Slot Card
One (1) CONCEAL Mount with hardware kit
One (1) 998-1001-232, 9-Pin D-Sub-F to RJ-45F EZCamera Control Adapter
Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
Part Number: 999-6967-001 International
One (1) Vaddio PowerVIEW HD-22PTZ Camera (998-6960-000)
One (1) Universal CCU Cat-5 for HD-22 or HD-30 with Rack Ears
One (1) 36 VDC, 2.78 Amp Switching power supply
One (1) Euro Power Cord
One (1) UK Power Cord
One( 1) 2-pin Phoenix-type 5.0mm Euro style connector (for Tally LED)
One (1) EZIM CCU Slot Card
One (1) CONCEAL Mount with hardware kit
One (1) 998-1001-232, 9-Pin D-Sub-F to RJ-45F EZCamera Control Adapter
Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
PowerVIEW HD-30 QCCU
Part Number: 999-6977-000, North America
One (1) Vaddio PowerVIEW HD-30 HD PTZ Camera (998-6970-000)
One (1) Universal CCU Cat-5 for HD-22 or HD-30 with Rack Ears
One (1) 36 VDC Switching power supply with power cord for North America
One( 1) 2-pin Phoenix-type 5.0mm Euro style connector (for Tally LED)
One (1) EZIM CCU Slot Card
One (1) CONCEAL Mount with hardware kit
One (1) 998-1001-232, 9-Pin D-Sub-F to RJ-45F EZCamera Control Adapter
Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
Part Number: 999-6977-001 International
One (1) Vaddio PowerVIEW HD-30 HD PTZ Camera (998-6970-000)
One (1) Universal CCU Cat-5 for HD-22 or HD-30 with Rack Ears
One (1) 36 VDC, 2.78 Amp Switching power supply
One (1) Euro Power Cord
One (1) UK Power Cord
One( 1) 2-pin Phoenix-type 5.0mm Euro style connector (for Tally LED)
One (1) EZIM CCU Slot Card
One (1) CONCEAL Mount with hardware kit
One (1) 998-1001-232, 9-Pin D-Sub-F to RJ-45F EZCamera Control Adapter
Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
CONCEAL Mount includes:
Metal Bracket,
Bottom Cover
Rear Connector/Cable Cover
Mounting Hardware
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 5 of 28
PowerVIEW HD-22/30 QCCU System
Anatomy of the HD-22 and HD-30
Image: PowerVIEW HD-22/30 HD PTZ Camera
Front View with Feature Call-outs:
①
②
④
③
1) Camera and Zoom Lens:
The 22X (HD-22) or 30X (HD-30) optical zoom lens is built around a (1/2.8 Type) high-speed MOS ima ge sens or
with a total of 2.2 megapixels for precise HD video image acquisition.
2) Red Tally Light:
A red tally light is illuminated when the camera receives a command from an external control system.
3) IR Sensors:
IR sensors are built into the front of the PowerVIEW HD-22/30 to receive IR signals from the IR remote control
supplied with the camera.
4) Blue Power Light:
A Vaddio blue power light is illuminated when the camera is turned on.
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 6 of 28
PowerVIEW HD-22/30 QCCU System
Image: PowerVIEW HD-20 or HD-30 HD PTZ Camera (Rear Panel)
Rear Panel Connections with Feature Call-outs
⑤
⑥
⑨
⑩
⑦
⑪
⑧
⑫
RS-232 & IR Out Port (Color Coded Blue):
5)
The RS-232 accepts modified VISCA protocol for camera control, however the IR Forwarding is not supported by the QuickConnect Universal CCU.
6) Dip Switch Settings:
Settings for IR remote, baud rate and image flip can be configured on these switches. See the Switch Settings
page for additional information.
7) HD Video Select:
A rotary switch allows the user to choose the component HD output video resolution and format. See the Switch
Settings page for additional information.
HD Resolution Note: When changing the resolution of the camera, the camera may need to be power-cycled. If changing the resolution
on any camera while plugged into even the most sophisticated switcher, the switcher may need to be reset or rebooted.
8) 12 VDC Input:
Power input for the standard, PowerVIEW HD-22 and HD-30 camera power sup ply.
9) HDMI Output:
The HDMI output feeds out HD digital video only (no copy protect or device communication is includ ed). The HDMI
output is optimized for HD video signals (seems logical).
10) YPbPr Output:
Component HD video (YPbPr) is output through the DE-15 connector. YPbPr and HDMI signals are si multaneous.
Limited SD resolutions are supported.
EZ-POWER VIDEO Port (Color Coded Orange):
11)
Interface, Quick-Connect DVI-D/HDMI SR Interface and the Quick-Connect USB Interface to supply power and
return HSDS (differential) video from the camera. This port is not used with the QCCU Systems.
12) Slot for Optional Cards:
The EZIM CCU slot card for the CCU can be plugged into the PowerVIEW HD-22 HD camera.
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 7 of 28
This RJ-45 connector is only used with the Quick-Connect SR
PowerVIEW HD-22/30 QCCU System
First Time Set-up with the PowerVIEW HD-22 or HD-30:
The PowerVIEW HD-22 and HD-30 were designed to be very easy to use an d operate. There is do cumentat ion at
the back of this manual for pin-outs of the connectors on the PowerVIEW HD-22 camera.
Step 1: Using the HD VIDEO SELECT rotary switch and CAMERA SETTINGS dip switches on the back of the
camera, set up the camera’s output resolution and functional preferences. There is a label on the bottom of the
camera that identifies the choices.
Important Dip Switch Note: Setting all dip switches down and power cycling the camera will load the factory default camera settings. For the
first time set-up, loading the defaults may be a good idea
Image: PowerVIEW HD-22/30 Rear Panel Connections
HD Video Select Switch Camera Settings 10-Pos Dip Switch
Drawing: Dip Switch and Resolution Label on the Bottom of the HD-22/30
IR 1
1 & 2 UP
DIP SWITCH SETTINGS
IR
9600
bps
OFF
5
OUT
OFF
OFF
IR 2ONIR 3
ON
12
21
ON
38400
bps
3
3
4
4
56
5
68109
a) Set the desired and available HD output resolution for the camera with the Rotary Switch.
b) Set the IR frequency of the camera if it is to respond to the IR remote control.
c) If using the IR forwarding feature, set the IR OUT switch to ON (SW3).
d) Set the Baud Rate dip switch (SW4) to 9600bps for most applications. Default for Vaddio EZCamera Cabling Systems is
9600bps.
e) To set the HDMI or DVI color space, use dip switch 7 (SW7).
f) If inverting the camera, turn the IMAGE FLIP ON (SW8).
Dip Switch Settings
IR 1 & 2: The IR remote has the capability of operating up to three different PTZ cameras from one remote. Use the
selector buttons at the top of the IR remote to select the frequency.
IR Out 3: The IR output is sent out on the RS-232 RJ-45 jack on the back of the camera. Turning on the IR output will
allow IR signals to be transmitted over the Cat-5 cable to the head end. When using RS-232 control or Vaddio CCU
controllers (also via RS-232), turn the IR OUT to OFF (up).
Baud Rate 4: The options for baud rate are either 9600 bps or 38,400 bps.
HDMI Color or sRGB Color space 7: Default is YCbCr. Use sRGB color space with older DVI-D 1.0 monitors only. The
YCbCr color space is best for HDMI digital video.
Image Flip 8: To invert the HD-20, turn the IMAGE FLIP ON (switch down).
Switches 9 and 10: Leave up - or in the OFF position
.
HD-22/30 Rear Panel
VIDEO RESOLUTION SELECT
IMAGE
HDMI
6
COLOR
YCbCr
sRGB
7
7
FLIP
OFF
ON
8
9
10
OFF
OFF
910
720p/59.94
0
1080i/59.94
1
1080p/59.94
2
3
720p/50
4
1080i/50
5
1080p/50
6
480p/59.94 1080p/25
7
8
9
A
B
C
D
E
F
576p/50
1080p/29.97
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 8 of 28
PowerVIEW HD-22/30 QCCU System
Anatomy of the Quick-Connect Universal CCU
The Universal CCU interfaces for the PowerVIEW HD-22 and the PowerVIEW HD-30 have very similar control
protocols and share the same control keypad. The Universal CCU will automatically sense the camera it is and
initialize the firmware for the connected camera. The next section will look at the controls and how they are laid
out for easy access.
Image: Quick-Connect Universal CCU HD-22/30 Front Panel Controls
Front Panel Controls (left to right):
5-Line Blue Back-lit LED: Displays up to control parameters at a time so the interrelationship of the controls can easily
and quickly be read and understood.
Tally Light: A contact closure on the back panel lights the blue LED on front panel ind icating which Universal CCU and
camera combination is the live Program in a multi-camera CCU installation. A tally command will also be sent to the camera
via RS-232 to light the LED on cameras with on-board tally lights (Vaddio HD Series cameras).
Image: Close up View of the Universal CCU HD-22/30 Control Panel
HD-22/HD-30 Keypad Controls from (left to right): Touch the button with the parameter to be controlled and
adjust the value with the encoder, then touch the cancel button to exit. When the rota ry encoder button is t ouched,
the SELECT and CANCEL menu buttons will illuminate to remind the user to either…select or cancel.
Scenes A, B & C: Three camera adjustment scenes (A, B & C) can be stored into microprocessor memory. When
lit (backlit blue button), the scene is activated. To store a scene, the user adjusts the controls and touches and holds
the scene button down until the button blinks. To erase a scene press and hold the scene button and the cancel
button.
Auto White Balance: The Automatic White Balance controls/adjusts the color lev els automatically when engaged.
Take it out of Auto to manually adjust the Red and Blue levels.
OPWB (One Push White Balance): When using OPWB, zoom in on a white subject (at least 60% of the image
must be true white) touch the OPWB button and the coloration of the image will adjust to the white used in this shot.
Red & Blue Gain Controls: The Red and Blue Gain buttons in combination with the encoder adjust the red and
blue gain of the signal when Auto White Balance is disengaged.
Chroma: Chroma controls the overall color saturation of the image.
PED: This is the Pedestal or black level control for the HD-22/HD-30 cameras.
Gamma: Gamma adjusts the overall brightness of an image to compensate for the perception of luminance and
chroma.
Detail: The Detail control sharpens or softens objects in the frame. Works well when looking at text.
IRIS - Auto or Manual: The Auto Iris mode automatically adjusts the iris and gain of the camera. To manually adjust
the iris or gain, turn off this control. The Manual Iris control allows the user to set the iris manually to one of the
several settings available
Gain: The Gain control boosts the signal level when the iris is open all the way, and there is not enough lighting
available. To manually adjust the Gain, Auto Iris must be off. Use the Gain last to enhance the image.
Rotary Encoder: Use the encoder to adjust values after the button is selected. This makes for very quick changes.
The Menu Buttons: There are other screens to be accessed other than the camera control screen. Use the SELECT
and CANCEL to enter other controls and exit other menus. These lights will illuminate for 10 Seconds, but no control
operations are interrupted.
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 9 of 28
PowerVIEW HD-22/30 QCCU System
Image: Rear Panel CCU Connections and Controls (left to right)
Pow er Supply Input: The Universal CCU uses a 36VDC, 2.78 Amp power supply on a 5.5mm OD x 2.5mm
ID coaxial connector with a positive center.
36 VDC to Camera - RED RJ-45: Power is provided on a Cat-5 cable to the RoboSHOT 36 VDC RJ-45 marked
for CCU use only (see page 9). The power is regulated in the camera to 12 VDC.
RS-232 IN - GREY RJ-45: RS-232 Input from ProductionVIEW™ console, Precision Camera Controller or
other custom camera control system. Daisy Chain topology is not supported.
RS-232 to Camera - BLUE RJ-45: RS-232 control is sent through this Cat-5 connection.
Local Tally on 2-pin Molex 5.0mm Euro-Style connector: A contact closure lights the blue LED on front
panel showing which Universal CCU and camera combination is the live Program in a multi-camera CCU
installation. A tally command will also be sent to the camera via RS-232 to illuminate the LED on the cameras
that have on-board tally lights.
Camera Feature Sw itches: The CCU interface has an 8-position dip switch on the rear panel to allow for
certain functionality. All switches should be in the down position for default.
Dip Switch 1: Put up to allow Scene A to load upon start-up or boot up.
Dip Switch 5: Put up to access LCD Display Menu settings including Display Mode, Bias and Contrast.
Video from Camera -
YELLOW
/ORANGE RJ-45: The yellow RJ-45 receives the camera’s differential video
signals from the PowerVIEW’s VIDEO RJ-45 on the EZIM CCU Slot Card (but there’s no power on the cable).
The orange EZ-POWER VIDEO RJ-45 on the PowerVIEW camera is not used (see drawings).
HD Video Outputs: The Universal CCU has 3 (three) simultaneous video output formats that are the same
resolution as the video inputs providing the ultimate in connectivity flexibility. The output formats include:
HD YPbPr on DE-15-F (HD15) - (supports up to/and including 1080p/60 - not limit ed)
HDMI on HDMI-F (supports up to and including 1080p/60)
HD-SDI on Edge Mount Carrier Class, Gold BNC-F (supports 3Gb/s Single Link 1080p/60 HD-SDI)
Big Important Note: The Quick-Connect Universal CCU supports the resolutions with frame rates
of above 50 Hz (60, 59.94 and 50). Consequently, the 30, 29.97 and 25 fps from the Vaddio
cameras are not supported
The EZIM (EZ Interface Module) HD-Series Slot Card
The EZIM Slot Card fits into the slot into the base of each of the HD-22 and HD-30 HD PTZ cameras and terminates
the Power (red) Cat-5 cable and the Video (yellow) Cat-5 cable to the camera (see colors abo ve).
Please remove power from the camera prior to inserting, seating a nd screwing down the card with the attached
thumb screws. Hot swapping is generally advised, so please…turn the camera off before inserting the slot Card.
Image: EZIM Slot Card
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 10 of 28
PowerVIEW HD-22/30 QCCU System
g
EZIM CCU Slot Card (Front View)
The HD-22 and HD-30 Control Menu Screens
The HD-22 and HD-30 have individual firmware that auto loads when the camera is plugged in to the Universal
CCU and the CCU is turned on (turn the camera on first). Since most cameras are a bit different, the menus will
be slightly different, but the Firmware is the same for the HD-22 and HD-30. The menus are organized as follows:
Image: Menu Organization HD-22/30
Main Control Menu
8-Most used Controls
displayed
CAT-5 Adjust Menu
With Skew, Color Space
Y-Gain and Six preset
Scene Confi
urations
The HD-22 and HD-30 individual control screens are very similar, only differing in lens magnification and product
name. Both cameras will perform well for low light, conferencing and large roo m applications.
The Main Menu screen shows eight (8) prominent parameters at a time. For both cameras, the BRIGHT key will
actually read out on the display as PEDESTAL. This control is actually PEDESTAL and the display is correct. The
button will be eventually changed to read PED (since pedestal won’t fit).
Main Menu Pages HD-22
CAT-5 CCU HD-22
RED 65 GAMMA 1
BLUE 75 DETAIL 44
CHROMA 190 IRIS AUTO
PEDESTAL 111 GAIN AUTO
The Cat-5 Adjustment Menu allows the user to adjust the skew of the Cat-5 Cable (1 to 16), to compensate for
differing Cat-5 cable lengths between camera and CCU. This setting will usually be best in the middle of the
range of skew numbers which pass acceptable video. Set the HDMI Color Space to YCbCr for HDMI and to
sRGB for DVI-D output. The Y-Gain is for adjusting the video ±10 IRE at all outputs as needed for associated
equipment. Preset Lighting Scene Configurations offer sample settings for fluorescent, incandesce nt and
outdoor lighting environments. Choose the scene (shown in the Screen Config description below) which looks
best for your situation and fine tune from there.
The Cat-5 Adjustment menu uses the “@’ sign for the cursor and the “>” when selected.
Cat-5 Adjustment Menu HD-22/30 with Scene >1: AUTO
CAT-5 CCU HD-22
@Skew 1 Scene Config
HDMI YCbCr >1: AUTO
YGain Def
Scene Configuration:
Generalized Scene Configurations have been added to allow the user to quickly run through preset lighting
environment scenes, and include the following presets:
1) AUTO (full Auto)
2) Incand Lo (incandescent low)
3) Incand Hi (incandescent high)
4) Fluor Lo (fluorescent low)
5) Fluor Hi (fluorescent high)
6) Outdoor
For this Menu, put
Dip Switch 5 UP
Camera Info Menu
Versions of camera
hardware
Main Menu Pages HD-30
For this Menu, put
Dip Switch 5 UP
LED Display Menu
For set up of front
panel LED display
CAT-5 CCU HD-30
RED AUTO GAMMA 1
BLUE AUTO DETAIL 44
CHROMA 190 IRIS AUTO
PEDESTAL 111 GAIN AUTO
Cat-5 Adjustment Menu HD-22/30 with Scene >4: Fluorescent High
CAT-5 CCU HD-30
Skew 1 Scene Config
@HDMI YCbCr >4: Fluor Hi
YGain Def
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 11 of 28
PowerVIEW HD-22/30 QCCU System
V
The Version Menu screen displays the software versions of the Vaddio cameras attached as a convenience to the
operator. The versions shown include the zoom module, the motors and the camera.
ersion Display Menu
CAT-5 CCU HD-22
CCU Version VERSION
V01.0x.ox CAM: V01.0X.0X *
FPGA Date: MOT: V02.0X.0X *
XX/XX/20XX
Put dip switch #5 UP to access this menu where the
firmware versions of the CCU, camera and motors
are displayed. The FPGA date is also displayed
The Display Menu provides controls for the blue LED display, including Bias (brightness), Display Mode - Normal
(negative mode) and Inverted (positive mode) and overall contrast are provided. Put dip switch #5 UP to access
this menu, make the adjustment and it is recommended that dip switch #5 is returned to th e DOWN position so this
menu is no longer seen.
Display Menu
CAT-5 CCU HD-22
DSPLY NORML
> Bias 1/9
Contrast 204
Put dip switch #5 UP to access the Display Menu.
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 12 of 28
PowerVIEW HD-22/30 QCCU System
Installation Basics:
The WallVIEW CCU system was specifically designed for installation on a vertical wall surface with
Cat-5 cable connectivity for Video, Power and Control signaling (three Cat-5 cables are required).
Installation is simplified in that no custom 8-Pin mini-din cables or expensive plenum coax cables are
needed and no power outlets are required near the camera brac ket. All cabli ng is routed to the head end using Cat-5 cables with standard straight through RJ-45 connectors (568B termination). “Pass-
thru” type RJ-45 connectors, as a rule should be avoided like a bad cliché.
General Installation Instructions for the CONCEAL Wall Mounting System:
Step 1: Determine Camera Mount Location
When locating the camera, consider viewing angles, lighting conditions, possible line of site obstructions an d check
for in-wall obstructions where the camera is to be mounted. Pick a mounting location to optimize the performance
of the camera. After determining the optimum location of the camera system, route the required three (3) Cat-5
cables from the camera to the head-end. Mark the Cables: POWER, VIDEO and CONTROL.
The three (3) Cat-5 cables should feed-through a 1” (25.4mm) opening (circular or square shape) centered in the
rectangular slot located on the rear flange of the CONCEAL Wall Mount Bracket.
Note: Do not cut out the entire rectangular slot opening in the wall! This will not allow the two lower wall
anchors to correctly fasten the Conceal Wall Mount to the wall.
If the bracket is to be mounted on a 2-gang wall box, use the screws supplied with the wall box cover plate to attach
the CONCEAL Wall Mount Bracket. If mounting to drywall with wall anchors, use the four (4) quality wall
anchors/screws provided
Note: The mounting holes are slotted and are 90° opposing to provide easy leveling. Level the mount and
tighten the mounting screws.
The example of the CONCEAL mount shows an HD-18, but the steps are identical for the HD-22 or HD-30.
Step 2: System Wiring
Follow the sample wiring diagrams for connecting the Cat-5 cables to the camera and Quick-Connect Universal
CCU Interface. Additional diagrams are available on the Vaddio website.
Connect the camera side as follows:
Connect the POWER Cat-5 to the Power RJ-45 on the EZIM CCU Slot Card.
Connect the VIDEO Cat-5 to the Video RJ-45 on the EZIM CCU Slot Card.
Connect the RS-232 control Cat-5 to the “RS-232 IN” RJ-45 on the top row of connectors on the camera.
Connect the Universal CCU side as follows:
Connect the VIDEO Cat-5 cable to the VIDEO FROM CAMERA RJ-45 jack (yellow) on the CCU.
Connect the RS-232 Cat-5 cable to the RS-232 TO CAMERA RJ-45 (Blue) on the CCU.
Wait to connect the POWER Cat-5 cable until later.
CONCEAL Wall Mount Bracket:
Cabled and Attached to Wall
Fig. 2: Camera aligned and attached to
the CONCEAL Wall Mount Bracket (by
two-(1/4”-20) screws in the bottom of
the mount).
Note: Check all Cat-5 cables for continuity in advance of final connection.
Plugging the POWER Cat-5 cable into the wrong RJ-45 may cause damage to the
camera system and void the warranty!
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 13 of 28
PowerVIEW HD-22/30 QCCU System
Step 3: Secure the Camera To the CONCEAL Wall Mount Bracket
After all cables are attached to the camera, place the camera onto the camera mount and insert the two 1/4”-20
screws into the camera through the two-screw holes in the bottom of the mount. Note: Be sure to align each side
of the camera evenly to all sides of the CONCEAL Wall Mount Bracket before final tightening of the mounting
screws.
Step 4: Install the CONCEAL Lower Cover Plate
Attach the CONCEAL lower cover plate. Slide lower cover plate from front of the mounting bracket toward the rear
of the bracket. The two (2) rear locking tabs will need to be guided into position first and will lock in place as the
lower cover plate is pushed toward the rear of the mounting bracket and the front two (2) tabs are inserted.
CONCEAL Lower Cover Plate
with Locking Tabs
CONCEAL Lower Cover
Plate locked in place
Step 5: Install the CONCEAL Rear Camera Cover
After successful testing of the camera, install the CONCEAL
rear camera cover on the mounting bracket with the supplied
screw (see Fig. 5 and 6).
CONCEAL Rear Camera Cover
Completed CONCEAL Wall Mount
Camera Bracket Installation
NOTE (One more time!): Check all Cat-5 cables for continuity in advance of the final
connection. Label the Cat-5 cables. Plugging the POWER cable into the wrong RJ-45 may
cause damage to the camera system and void the warranty.
Step 6: Connect System Power
Connect the Vaddio 36 VDC power supply to the Quick-Connect Universal CCU Interface and an AC outlet. The
CCU will power the camera via the Cat-5 cable. The camera will “Home” to a centered position ready for control
information from the Universal CCU. To ensure proper continuity of control and operation of the cameras, t he RS232 controller (control system or joystick) should be powered on after the camera(s).
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 14 of 28
PowerVIEW HD-22/30 QCCU System
Drawing: Basic System Connectivity
Wiring Diagram Example:
Rear Panel of HD-22 with EZIM
CCU Slot Card installed in the
bottom row slot. All Universal CCU
camera packages are shipped with
the EZIM CCU Slot Card.
Please see the manuals for each of
the cameras for specifics regarding
set-up and switch settings.
PowerVIEW
HD-22 or HD-30
EZ-POWER VIDEO Port (color
coded orange) is not used with the
QCCU System
EZIM CCU Slot Card
36 VDC POWER (red to red)
RS-232 (blue to blue)
Cat-5e Cables up to
’
HSDS VIDEO
(yellow to yellow)
YPbPr 1080i/59.94
HDMI 1080i/59.94
Quick-Connect
Universal CCU
RS-232
HD-SDI 1080i/59.94
All 3 Video Outputs
are simultaneous &
the same resolution
HD-SDI
DVI
Program Output
Simulated Video Feed
Multi-viewer Output
Simulated Video Feeds
System Configuration Notes:
The Quick-Connect Universal CCU System uses a full Cat-5 (all 4-pairs) for POWER to ensure the motors of the camera receive the required current to operate
properly. The VIDEO Cat-5 cable uses all four pairs for video. The RS-232 Cat-5 provides communication to the camera for CCU and PTZ control. These Cat.-5
cables can be run up to 500’ (152.4m). See Appendix 1 for wiring and pin-out information. NOTE: Daisy-Chain configurations are not supported.
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 15 of 28
PowerVIEW HD-22/30 QCCU System
Optimizing System Performance:
Optimizing the CCU settings will help achieve maximum performance from the system. Difficult
lighting is one of the most challenging problems video system integrators face. The Vaddio
CCU will provide the flexibility to fine tune for variables such as cable length, day/night lighting
transitions and lighting color temperature.
1. Adjust Y Gain: Allows for the adjustment of luminance gain up to +/- 10% as needed to compensate for a too
light or dark image in downstream equipment.
2. Set skew control: Adjust to afford the best picture brightness, quality and clarity. The range is 0-16. There
will typically be a range of values where the video will output a valid image. The best setting is usually achieved
with a number roughly in the middle of this valid video range.
3. Adjust Iris and Digital Gain Settings: Disable Auto Iris. Set the Iris to its largest aperture (lowest ‘f’ number).
Adjust the Gain until the image is too dark and then bring it back until it is properly exposed. Exposures that
require high gain settings will have a grainy video image. Adjust the detail settings for a smoother image.
4. Adjust Color to Taste: Required adjustments will vary based on the environment. The CCU allows the set-
up of three (3) scenes so settings are available for a variety of conditions. Adjust the Chroma level to taste.
Adjust Red/Blue levels next. Adjusting for skin tones or using a color chart is an easy way to find a good
baseline setup.
IMPORTANT
Changing the HD Resolution of the HD-22 and HD-30: When changing the resolution
of the HD-22 and HD-30 cameras, the camera may need to be power-cycled. This ensures
that all of the settings for that resolution are intact. If the camera resolution is changed
while connected to a video switcher (even the expensive ones), the switcher will need to
be reset to that resolution and most probably power cycled while the camera is on. The
boot order method when connecting a camera to a 3
rd
party video switcher is:
a) Set the camera’s output resolution
b) Set the switcher’s input resolution
Make sure these resolutions match!
c) Turn on the Universal CCU and Camera System (let it boot up completely and Home)
rd
d) Turn on the 3
party video switcher
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 16 of 28
PowerVIEW HD-22/30 QCCU System
V
General Specifications: (Note: Specifications and pricing are subject to change without prior notice or obligation.)
Camera PowerVIEW HD-22 PTZ PowerVIEW HD-30 PTZ
Part Numbers 999-6960-000 (North America)
999-6960-001 (Int’l)
Zoom 22X Optical Zoom 30X Optical Zoom
Field of View Horizontal: 65.2º Wide End to 3.1º Tele
(16:9 Aspect Ratio)
Lens Focal Length f=4.3 mm to 94.6 mm / F1.6 - F4.7 f=4.3mm to 129.0 mm / F1.6- F4.7
Image Sensor 1/2.8-Type MOS, 2.2 Megapixel, Progressive Scan
Minimum Illumination Color: 0.4 lux (F1.6, 1/30 sec, 50 IRE, Gain: High),
B/W: 0.04 lux (F1.6, 1/30 sec, 50 IRE, Gain: High)
Video Resolutions HD: 1080p/59.94, 1080p/50, 1080p/29.97/25, 1080i/59.94, 1080i/50, 720p/59.94, 720p/50
Video Output Formats HDMI (YCbCr for HDMI and sRGB for DVI), Analog Component (YPbPr)
HSDS (Power, Differential HD Video & R$S-232 Control)
Signal to Noise Ratio > 50 dB (AGC: Off)
Compatible
Quick-Connects
Pan Range Pan: +170 degrees to -170 degrees
Preset Positions 16 (internal), 6 recalled via Vaddio IR Remote Commander
Image Control Red & Blue Gain, Detail, Chroma, Gamma, Pedestal, Iris, and Gain
Tally Light Available through RS-232 Control
HD Video Select 16-Position Rotary Switch: Used to set HD Video Resolution Output
Camera Settings 10-Position Dip Switch: Settings for IR Select, Baud Rate 9600, Image Flip, Unpublished
Accessory Slot Cards EZIM CCU Slot Card PN# 999-6900-006 - For Use with Quick-Connect CCU Only
Dimensions/Weight 7.81” (198.37mm) H x 6.67” (169.42mm) W x 7.057” (179.25. mm) D / 5.6 lbs. (2.630835643 kg.)
Quick-Connect Universal CCU
Connectors
Camera Settings
DIP Switch
ideo Adjustments
Cat-5 Cable Distance
Power Supply
Dimensions
EZIM (EZCamera Interface Module) Slot Card
Connectors
Moon in Front Page Header: Titania, Largest Moon of the planet Uranus.
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 17 of 28
Quick-Connect SR, Quick-Connect DVI/HDMI SR, Quick-Connect Universal CCU and Quick-
Connect USB (varying voltages), USB Mini
Tilt: +90 degrees to -30 degrees
(Controls available through RS-232 control and Quick-Connect CCU and Slot Card)
Functions
Power Connector: 5.5mm OD x 2.5mm ID
Power RJ-45: Supplies 36V to EZIM Slot Card
RS-232 IN RJ-45: Accepts RS-232 from ProductionVIEW or other control systems
RS-232 OUT RJ-45: Passes RS-232 and Sync video feed to camera EZIM
Tally: 2-Pin Phoenix type spring cage connector
Video From Camera RJ-45: Accepts differential video from EZIM Slot Card
Video Outputs:
HD-YPbPr on DE-15-F connector
HDMI on HDMI-F connector
HD-SDI on Edge Mount Carrier Class, Gold BNC-F, supports 3Gb/s Single Link 1080p/60
All switches should be in the down position for default.
DIP Switch 1: Put up to allow Scene A to load upon start-up or boot up.
DIP Switch 5: Put up to access LCD Display Menu settings including Display Mode (Negative
Mode-Default or Positive Mode), Bias (Brightness) and Contrast.
DIP Switches 2, 3, 4, 6, 7 & 8: NA for HD-22 anHD-30
Y-Gain (+/- up to 10 IRE luminance gain) for fine tuning over longer cable distances
Skew for cabling distance compensation:
Up to 500’ (152.4m), Maximum
36 VDC, 2.78 Amp
1-RU Rack Mount - 1.72” H x 18.93” W x 7” D (43.7mm x 480.1mm x 177.8mm)
Rack Ears Included
Two (2) RJ-45 Connectors
For Power and HSDS Video
999-6970-000 (North America)
999-6970-001 (Int’l)
Horizontal: 65º Wide End to 2.2º Tele
(16:9 Aspect Ratio)
PowerVIEW HD-22/30 QCCU System
Warranty Information:
(See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details)
Hardware* Warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured products. Vaddio warrants
its manufactured products against defects in materials and workmanship for a period of two years from the day of purchase, to
the original purchaser, if Vaddio receives notice of such defects during the warranty. Vaddio, at its option, will repair or replace
products that prove to be defective. Vaddio manufactures its hardware products from parts and components that are ne w or
equivalent to new in accordance with industry standard practices.
Exclusions: The above warranty shall not apply to defects resulting from improper or inadequate maintenance by the customer,
customers applied software or interfacing, unauthorized modifications or misuse, mish andling, operation outside the normal
environmental specifications for the product, use of the incorrect power supply, modified power supply or improper site operation
and maintenance. OEM products and products manufactured by other companies are excluded and are covered by the
manufacturer’s warranty
Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under
warranty. If the product is out of warranty, Vaddio will test then repair the product or products. The cost of parts and labor
charge will be estimated by a technician and confirmed by the customer prior to repair. All components must be returned for
testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.
Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs and/or
replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at
support@vaddio.com or online at www.vaddio.com.
Return Material Authorization (RMA) Number: Before returning a product for repair or replacement request an RMA from
Vaddio’s technical support. Provide the technician with a return phone number, e-mail address, shipping address, product serial
numbers and original purchase order number. Describe the reas on for r epairs or returns as well as the date of purch ase. See
the General RMA Terms and Procedures section for more information. RMA’s are valid for 30 days and will be issued to Vaddio
dealers only. End users must return products through Vaddio dealers. Include the assigned RMA number in all correspondence
with Vaddio. Write the assigned RMA number clearly on the shipping label of the box when returning the product. All products
returned for credit are subject to a restocking charge without exception.
Voided Warranty: The warranty does not apply if the original serial number has be en removed or if the product has been
disassembled or damaged through misuse, accident, modifications, us e of incorrect power supply, use of a modified power
supply or unauthorized repair.
Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any
responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and insurance
charges for all items under warranty but will not assume responsibility for l oss and/or damage by the outbound freight carrier. f
the return shipment appears damaged, retain the original boxes and packing material for inspection by the carrier. Contact your
carrier immediately.
Products not under Warranty: Payment arrangements are required before outbound shipment for all out of warranty products.
Other General Information:
Care and Cleaning
Do not attempt to take this product apart at any time. There are no user-serviceable components inside.
Do not spill liquids in the product.
Keep this device away from food and liquid.
For smears or smudges on the product, wipe with a clean, soft cloth.
Use a quality lens cleaning cloth on the lens
Do not use any abrasive chemicals.
Operating and Storage Conditions:
Do not store or operate the device under the following conditions:
Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)
High humidity, condensing or wet environments
In swimming pools with movie stars (privacy issue)
In inclement weather
Dry environments with an excess of static discharge
In an underwater igloo or beaver dam
Under severe vibration
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 18 of 28
PowerVIEW HD-22/30 QCCU System
Compliance and CE Declaration of Conformity - PowerVIEW HD-22 and HD30
Compliance testing was performed to the following regulations:
FCC Part 15 (15.107, 15.109), Subpart B Class A
ICES-003, Issue 4: 2004 Class A
EN 55022 A: 2006 + A1: 2007 Class A
KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) Class A
KN22 2008 (CISPR 22: 2006) Class A
EMC Directive 2004/108/EC Class A
EN 55024: A2: 2003
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his/her own
expense.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device
must accept any interference including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the
user’s authority to operate this equipment.
ICES-003 Compliance
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le
ministère des Communications du Canada.
European Compliance
This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures.
Standard(s) To Which Conformity Is Declared:
EMC Directive 2004/108/EC
EN 55022 A: 2006 + A1: 2007(CISPR 22:2005/A1:2005)
EN 55024: 1998 + Amendments A1: 2001 + A2: 2003
EN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001 Electrostatic Discharge
EN 61000-4-3: 2006 + A1: 2008 Radiated Immunity
EN 61000-4-4: 2004 + Corrigendum 2006 Electrical Fast Transients
EN 61000-4-5: 2006 Surge Immunity
EN 61000-4-6: 2009 Conducted Immunity
EN 61000-4-8: 2010 Power Frequency Magnetic Field
EN 61000-4-11: 2004 Voltage Dips, Interrupts and Fluctuations
KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002)
KN 61000-4-2 Electrostatic Discharge
KN 61000-4-3 Radiated Immunity
KN 61000-4-4 Electrical Fast Transients
KN 61000-4-5 Surge Immunity
KN 61000-4-6 Conducted Immunity
KN 61000-4-8 Power Frequency Magnetic Field
KN 61000-4-11 Voltage Dips, Interrupts and Fluctuations
IEC 60950-1:2005 (2nd Edition); Am 1:2009
EN 60950-1:2006+A11:2009+A1:2010+A12:2011
Class A
Radiated and Conducted Emissions
Immunity
IT Immunity Characteristics
Safety
Safety
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 19 of 28
PowerVIEW HD-22/30 QCCU System
Compliance and CE Declaration of Conformity - Universal CCU and EZIM CCU
Compliance testing was performed to the following regulations:
FCC Part 15, Subpart B Class A
ICES-003, Issue 4: 2004 Class A
European Standard EN 55022 A: October 2007 Class A
European Standard EN 55024/A2 January 2003 Class A
IEC 60950-1:2005 (Second Edition); Am 1:2009 Safety
EN 60950-1:2006+A11:2009+A1:2010+A12:2011 Safety
EMC Directive 89/336/EC Class A
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A dig ital device, pursuant to Part 15, Subpart
B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his/her own expense.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept
any interference including interference that may cause unde s ired operation of the device.
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the user’s authority
to operate this equipment.
ICES-003 Compliance
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital ap paratus set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux appareils numeriques
de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le ministère des Communications du
Canada.
European Compliance
This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and Immunity and
meets the requirements for a Class A digital device. In a domestic environment this product may cause radio interferenc e in
which case the user may be required to take adequate measures.
Standard(s) To Which Conformity Is Declared:
EMC Directive 89/336/EC
EN 55022 A: 1998 + A1: 2000 Conducted and Radiated Emissions
EN 55024: 1998 + Amendments A1: 2001 + A2: 2002 Immunity
EN 61000-4-2: Electrostatic Discharge
EN 61000-4-3: Radiated Immunity
EN 61000-4-4: Electrical Fast Transients
EN 61000-4-5: Surge Immunity
EN 61000-4-6: Conducted Immunity
EN 61000-4-8: Power Frequency Magnetic Field
EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations
IEC 60950-1:2005 (Second Edition); Am 1:2009 Safety
EN 60950-1:2006+A11:2009+A1:2010+A12:2011 Safety
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 20 of 28
PowerVIEW HD-22/30 QCCU System
Appendix 1: Cable Pin-outs for the Quick-Connect CCU System
Quick-Connect CCU Pin-out Assignments:
Power Connector RJ-45 (Red)
Pin # Function Pairs
Pin - 1 Power +
Pin - 2 Power Pin - 3 Power +
Pin - 4 Power Pin - 5 Power + 3
Pin - 6 Power - 2
Pin - 7 Power + 4
Pin - 8 Power - 4
RS-232 IN RJ-45 (Green)
Pin # Function Pairs
Pin - 1 N/A
Pin - 2 N/A
Pin - 3 N/A
Pin - 4 N/A
Pin - 5 N/A Not Used
Pin - 6 Digital GND
Pin - 7 RXD (from TXD of control source) 4
Pin - 8 TXD (to RXD of control source) 4
RS-232 OUT RJ-45 (Blue)
Not Used
Not Used
Not Used
Not Used
Pin # Function Pairs
Pin - 1 N/A
Pin - 2 N/A
Pin - 3 N/A
Pin - 4 N/A
Pin - 5 N/A Not Used
Pin - 6 Digital GND
Pin - 7 TXD (to RXD of control source) 4
Pin - 8 RXD (from TXD of control source) 4
Video (HSDS-differential) RJ-45 (Yellow)
Not Used
Not Used
Not Used
Not Used
Pin # Function Pairs
Pin - 1 N/A Not Used
Pin - 2 N/A Not Used
Pin - 3 Y+ 2
Pin - 4 PB+ 3
Pin - 5 PB GND 3
Pin - 6 Y GND 2
Pin - 7 PR+ 4
Pin - 8 PR- 4
1
1
2
3
36 VDC TO
CAMERA
12345678
RS-232 IN
12345678
RS-232 TO
CAMERA
12345678
VIDEO FROM
CAMERA
12345678
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 21 of 28
PowerVIEW HD-22/30 QCCU System
Appendix 1 (continued)
EZIM Slot Card Pin-out Assignments
Power Connector RJ-45 (Red)
Pin # Function Pairs
Pin - 1 Power +
Pin - 2 Power Pin - 3 Power +
Pin - 4 Power Pin - 5 Power + 3
Pin - 6 Power - 2
Pin - 7 Power + 4
Pin - 8 Power - 4
Video (HSDS-differential) RJ-45
Pin # Function Pairs
Pin - 1 N/A Not Used
Pin - 2 N/A Not Used
Pin - 3 Y+ 2
Pin - 4 PB+ 3
Pin - 5 PB GND 3
Pin - 6 Y GND 2
Pin - 7 PR+ 4
Pin - 8 PR- 4
1
1
2
3
12345678
POWER
12345678
VIDEO
Table: New Commands for the CCU Scene Selection
Command Set Command Command Packet Comments
QCCUScenes Reset
Set
Recall
8x 01 04 3F 00 7p FF
8x 01 04 3F 01 7p FF
8x 01 04 3F 02 7p FF
p: Scene Number =1, 2 or 3
Notes:
For use with Quick-Connect Universal CCU (QCCU), which no daisy-chain operation is allowed, the Command
packet will be 81 01 043F 00 7p FF (where the p is scene 1, 2 or 3.)
A Vaddio PTZ camera must be connected to the QCCU for the scene Set, Recall, and Reset to operate correctly.
This command set communicates with the QCCU and the camera simultaneously.
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 22 of 28
PowerVIEW HD-22/30 QCCU System
V
Appendix 2: PowerVIEW EZ-Power Video RJ-45 Connector Pin-outs
Important Note: The EZ-Power Video RJ-45 Connector is for use with the Quick-Connect SR, Quick-
Connect DVI/HDMI SR and Quick-Connect USB Interfaces ONLY (568B Wiring Standard). The video
signals are differential (HSDS™) and can only be received by the interfaces above. The Universal CCU
Power and Video connections are on the EZIM CCU Slot Card ONLY
Drawing: PowerVIEW HD-22/30 Dimensions
Pin YPbPr
1 Power+
2 Power3 Y+
4 PB+
5 PB 6 Y 7 PR+
8 PR-
EZ-POWER
IDEO
12345678
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 23 of 28
PowerVIEW HD-22/30 QCCU System
Appendix 3: Communication Specification
Communication Speed: 9600 bps (default)
Start bit: 1
Stop bit: 1
Data bits: 8
12345678
Parity: None
No Flow control
NOTE: The Vaddio PowerVIEW HD-22 and 30Control Protocol is similar, but not identical to, the Sony® VISCA™
command set in order to be compatible with several popular control devices. Not all VISCA commands are
supported and there are many HD-22/30 specific commands in the following Command and Inquiry Lists.
HD-22/30 Command List (1/2)
Command Set Command Command Packet Comments
Address Set Broadcast 88 30 01 FF Address Set (Daisy chain)
IF_Clear Broadcast 88 01 00 01 FF IF Clear
Command Cancel 8x 2p FF p:socket number(1,2)
CAM_Power On
CAM_Zoom Stop
CAM_Focus Stop
CAM_WB Auto
CAM_RGain Reset
CAM_BGain Reset
CAM_AE Full Auto
CAM_Iris Reset
CAM_Gain Reset
CAM_Backlight On
CAM_Aperture Reset
*Zoom and Focus Data:
CAM_Zoom: Range (0x000–0xA23/0xA73), HD22: 0xA23(22x Zoom), HD30: 0xA73(30x Zoom)
CAM_Focus: Range (0x000-0x438) dependent on Zoom Position
Off(Standby)
Tele(Standard)
Wide(Standard)
Tele(Variable)
Wide(Variable)
Direct
Far(Standard)
Near(Standard)
Far(Variable)
Near(Variable)
AutoFocus
ManualFocus
Auto/Manual
Direct
Indoor
Outdoor
One Push WB
Manual
Fluorescent
One Push Trigger
Up
Down
Direct
Up
Down
Direct
Manual
Up
Down
Direct
Up
Down
Direct
Off
Up
Down
Direct
8x 01 04 00 02 FF
8x 01 04 00 03 FF
8x 01 04 07 00 FF
8x 01 04 07 02 FF
8x 01 04 07 03 FF
8x 01 04 07 2p FF
8x 01 04 07 3p FF
8x 01 04 47 00 0p 0q 0r FF
8x 01 04 08 00 FF
8x 01 04 08 02 FF
8x 01 04 08 03 FF
8x 01 04 08 2p FF
8x 01 04 08 3p FF
8x 01 04 38 02 FF
8x 01 04 38 03 FF
8x 01 04 38 10 FF
8x 01 04 48 0p 0q 0r 0s FF
8x 01 04 35 00 FF
8x 01 04 35 01 FF
8x 01 04 35 02 FF
8x 01 04 35 03 FF
8x 01 04 35 05 FF
8x 01 04 35 06 FF
8x 01 04 10 05 FF
8x 01 04 03 00 FF
8x 01 04 03 02 FF
8x 01 04 03 03 FF
8x 01 04 43 00 00 0p 0q FF
8x 01 04 04 00 FF
8x 01 04 04 02 FF
8x 01 04 04 03 FF
8x 01 04 44 00 00 0p 0q FF
8x 01 04 39 00 FF
8x 01 04 39 03 FF
8x 01 04 0B 00 FF
8x 01 04 0B 02 FF
8x 01 04 0B 03 FF
8x 01 04 4B 00 00 0p 0q FF
8x 01 04 0C 00 FF
8x 01 04 0C 02 FF
8x 01 04 0C 03 FF
8x 01 04 4C 00 00 0p 0q FF
8x 01 04 33 02 FF
8x 01 04 33 03 FF
8x 01 04 02 00 FF
8x 01 04 02 02 FF
8x 01 04 02 03 FF
8x 01 04 42 00 00 0p 0q FF
Pin # RJ-45 RS-232 and IR Out Pins
1) Unused
2) Unused
3) Unused
4) IR Output (Diff Signal to Quick-Connect SR)
5) IR Ground (Diff Signal to Quick-Connect SR)
6) GND (GND of IR Short Range - Pin 3)
7) RXD (from TXD of control source)
8) TXD (to RXD of control source)
Power On/Off
p:(1-Slow to 4-Fast)
p:(1-Slow to 4-Fast)
pqr: Zoom Position*
p:(1-Slow to 4-Fast)
p:(1-Slow to 4-Fast)
pqrs: Focus position(0-0x438)*
Normal Auto (Auto Tracing WB)
Indoor Mode (Color Temp 3200K)
Outdoor Mode (Color Temp 5600K)
One Push White Balance Mode
Manual White Balance
Fluorescent(Color Temp 4200K)
One Push WB Trigger
pq:00-ff
pq:00-ff
Auto Exposure Mode
Manual Control Mode
pq(0x00-0xFF)
pq(0x00-0xFF)
pq(0x00-0x3F)
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 24 of 28
PowerVIEW HD-22/30 QCCU System
HD-22/30 Command List (2/2)
Command Set Command Command Packet Comments
CAM_Memory Reset
Set
Recall
CAM_IDWrite 8x 01 04 22 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFFF
CAM_LR_Reverse On
Off
CAM_Freeze On
Off
CAM_PictureEffect Color
B&W
Pan-tiltDrive Up
Down
Left
Right
UpLeft
UpRight
DownLeft
DownRight
Stop
Absolute Position
Home
Reset
Tally On
Off
Preset Pan Speed Pan/Tilt/Zoom Speed 8x 01 7E 01 0B WW SS ZZ FF WW: Pan Speed (0x01-0x18)
Motor Config Hard Motor Stops
Soft Motor Stops
BLK.Enhance Pedestal 8x 01 7E 53 00 00 0p 0q FF Pq: Pedestal(0x00-0xFF)
GMA.Enhance Gamma 8x 01 7E 54 00 00 0p 0q FF pq: Gamma (0x00-0x03)
CRM.Enhance Chroma 8x 01 7E 55 00 00 0p 0q FF pq: Chroma (0x00-0xFF)
KNE.Enhance Knee No Support No Support
DIS.Enhance Digital Image
Stabilizer
DNR.Enhance Digital Noise
Reduction
AGC.Enhance AGC Mode 8x 01 7E 59 00 FF
CAM_Shutter No Support No Support No Support
CAM_ICR ICR Off
ICR On
8x 01 04 3F 00 0p FF
8x 01 04 3F 01 0p FF
8x 01 04 3F 02 0p FF
8x 01 04 61 02 FF
8x 01 04 61 03 FF
8x 01 04 62 02 FF
8x 01 04 62 03 FF
8x 01 04 63 00 FF
8x 01 04 63 04 FF
8x 01 06 01 VV WW 03 01 FF
8x 01 06 01 VV WW 03 02 FF
8x 01 06 01 VV WW 01 03 FF
8x 01 06 01 VV WW 02 03 FF
8x 01 06 01 VV WW 01 01 FF
8x 01 06 01 VV WW 02 01 FF
8x 01 06 01 VV WW 01 02 FF
8x 01 06 01 VV WW 02 02 FF
8x 01 06 01 VV WW 03 03 FF
8x 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
8x 01 06 04 FF
8x 01 06 05 FF
8x 01 7E 01 0A 00 02 FF
8x 01 7E 01 0A 00 03 FF
8x 01 7E 01 70 00 00 FF
8x 01 7E 01 70 00 01 FF
8x 01 7E 57 02 FF
8x 01 7E 57 03 FF
8x 01 7E 58 02 FF
8x 01 7E 58 03 FF
8x 01 7E 59 01 FF
8x 01 7E 59 02 FF
8x 01 7E 59 03 FF
8x 01 7E 59 04 FF
8x 01 7E 59 05 FF
8x 01 7E 59 06 FF
8x 01 7E 59 07 FF
8x 01 7E 59 00 0p FF
8x 01 04 01 02 FF
8x 01 04 01 03 FF
p:Memory No(=0-0xF)
Mirror (Horizontal) on
Mirror (Horizontal) off
Still image on
VV: Pan Speed (0x01-0x18)
WW: Tilt Speed(0x01-0x14)
YYYY: Pan Position**
ZZZZ: Tilt Position**
SS:Tilt Speed(0x01-0x14)
ZZ:Zoom Speed(0-7);
On
Off
On
Off
Off Manual AGC Gain (0dB)
Low
Medium
High
Low1
Low2
Med1
High1
Off p: Manual AGC Gain(1-0x0e)***
ICR Off Color
ICR On Black and White
**Additional Information:
Pan Range: 8044 – 7FBC (-32,700 to +32,700)
Tilt Range: E891 – 4C2B (-5,999 to +19,499)
Actual Pan/Tilt ranges defined in Inquiry list
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 25 of 28
PowerVIEW HD-22/30 QCCU System
HD-22/30 Inquiry List (1/1)
Inquiry Command Command Response Packet Comments
CAM_PowerInq 8x 09 04 00 FF y0 50 02 FF
CAM_ICRModeInq 8x 09 04 01 FF y0 50 02 FF
CAM_BacklightModeInq 8x 09 04 33 FF y0 50 02 FF
CAM_WBModeInq 81 09 04 35 FF y0 50 00 FF
CAM_AEModeInq 8x 09 04 39 FF y0 50 00 FF
CAM_LR_Reverse 8x 09 04 61 FF y0 50 02 FF
CAM_Freeze 8x 09 04 62 FF y0 50 02 FF
CAM_PictureEffect 8x 01 04 63 FF y0 50 00 FF
CAM_MemoryInq 8x 09 04 3F FF y0 50 0p FF p:Preset 0-0xf
CAM_IDInq 8x 09 04 22 FF y0 50 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFFF
CAM_ApertureInq 8x 09 04 42 FF y0 50 00 00 0p 0q FF Pq:x00-0x3F
CAM_RGain 8x 09 04 43 FF y0 50 00 00 0p 0q FF pq:000-0ff
CAM_BGain 8x 09 04 44 FF y0 50 00 00 0p 0q FF pq:000-0ff
CAM_ZoomPosInq 8x 09 04 47 FF y0 50 0p 0q 0r 0s FF pqr: 0-0x6B3
CAM_FocusPosInq 8x 09 04 48 FF y0 50 0p 0q 0r 0s FF pqrs: Focus Position
CAM_FocusModeInq 8x 09 04 38 FF y0 50 02 FF
CAM_Gain 8x 09 04 4C FF y0 50 00 00 0p 0q FF pq(0x00-0x24)
CAM_IRReceiveInq 8x 09 06 08 FF y0 50 02 FF
Pan-TiltMaxSpeedInq 8x 09 06 11 FF y0 50 pp qq FF pp:Pan 0x01-0x18
Pan-tiltPositionInq 8x 09 06 12 FF FF y0 50 0p 0p 0p 0p 0q 0q 0q 0q FF pppp: Pan 0x8044-0x7FB2
CAM_ShutterPosInq No support No support Shutter Position
TallyInq 8x 09 7E 01 0A FF y0 50 02 FF
PresetSpeedInq 8x 09 7E 01 0B FF y0 50 pp qq rr FF pp:Pan 0x01-0x18
Motor Config 8x 09 7E 01 70 FF y0 50 00 FF
BLK.Enhance 8x 09 7E 53 FF y0 50 00 00 0p 0q FF pq: Pedestal(0x00-0xFF)
GMA.Enhance 8x 09 7E 54 FF y0 50 00 00 00 0p FF p: Gamma (0x00-0x03)
CRM.Enhance 8x 09 7E 55 FF y0 50 00 00 0p 0q FF p: Chroma (0x00-0xFF)
KNE.Enhance No support No Support Knee
DIS.Enhance 8x 09 7E 57 FF y0 50 02 FF
DNR.Enhance 8x 09 7E 58 FF y0 50 02 FF
AGC.Enhance 8x 09 7E 59 FF
8x 09 7E 59 00 FF
y0 50 03 FF
y0 50 03 FF
y0 50 03 FF
y0 50 01 FF
y0 50 02 FF
y0 50 03 FF
y0 50 05 FF
y0 50 06 FF
y0 50 03 FF
y0 50 03 FF
y0 50 03 FF
y0 50 04 FF
y0 50 03 FF
y0 50 03 FF
y0 50 03 FF
y0 50 01 FF
y0 50 03 FF
y0 50 03 FF
y0 50 00 FF
y0 50 01 FF
y0 50 02 FF
y0 50 03 FF
y0 50 04 FF
y0 50 05 FF
y0 50 06 FF
y0 50 07 FF
y0 50 0p FF
On
Off(Standby)
On - ICR filter Out
Off – ICR filter In
On
Off
Auto
Indoor
Outdoor
One Push WB
Manual
Fluorescent
Auto Exposure Mode
Manual Control Mode
On
Off
On
Off
Off
B&W
Auto
Manual
On
Off
qq:Tilt 0x01-0x14
qqqq: Tilt 0xE890-0x4C2C
On
Off
qq:Tilt 0x01-0x14
rr:Zoom 0x00-0x07
Hard Motor Stops
Soft Motor Stops
On
Off
On
Off
Off Manual AGC Gain(0dB)
Low
Medium
High
Low1
Low2
Med1
High1
Off p: Manual AGC Gain(0-0x0e)***
***Manual AGC Gain: 0:0dB, 1:3dB, 2:6dB, 3:9dB, 4:12dB, 5:15dB, 6:18dB, 7:21dB, 8:24dB, 9:27dB, 10:30dB, 11:33dB,
12:36dB, 13:39dB & 14:42dB
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 26 of 28
PowerVIEW HD-22/30 QCCU System
Inside Back Cover - Blank
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 27 of 28
PowerVIEW HD-22/30 QCCU System
©2015 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject
to change without notice. Vaddio, Quick-Connect, ProductionVIEW, HSDS, EZIM, CONCEAL and PowerVIEW are trademarks of Vaddio. All other
Vaddio PowerVIEW HD-22/30 QCCU System, Document Number 342-064F Rev F Page 28 of 28
trademarks are property of their respective owners. Document 342-0645 Rev F, SD: 68670.0
Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464
www.vaddio.com
Loading...