Installation and User Guide
VADDIO™ POWERVIEW™ HD-22 QSR AND POWERVIEW
HD-30 QSR CAMERA SYSTEMS
PowerVIEW Series High Definition PTZ Cameras featuring the Quick-Connect™ SR
Interface
PowerVIEW HD-22 QSR - High Definition PTZ Camera System
Model Number 999-6965-000 (North America)
Model Number 999-6965-001 (International)
PowerVIEW HD-30 QSR - High Definition PTZ Camera System
Model Number 999-6975-000 (North America)
Model Number 999-6975-001 (International)
PowerVIEW 22/30 with CONCEAL Mount
Quick-Connect SR Interface
Part Number: 998-1105-016
(22X Optical Zoom)
(30X Optical Zoom)
© 2015 Vaddio - All Rights Reserved. PowerVIEW HD-22 QSR & HD-30 QSR Camera Systems - Document Number 342-0643 Rev D
PowerVIEW HD-22 and HD-30 QSR Systems
Inside Front Cover - Very Blank
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 2 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
TABLE OF CONTENTS
PowerVIEW 22/30 with CONCEAL Mount ............................................................................................................. 1
Overview .................................................................................................................................................................... 4
Unpacking .................................................................................................................................................................. 5
Camera Front View with Feature Call-outs ............................................................................................................ 6
Image: PowerVIEW HD-22/30 SR Camera System .......................................................................................... 6
Rear Panel Connections with Feature Call-outs .................................................................................................... 7
Image: PowerVIEW HD-22/30 SR Camera System .......................................................................................... 7
First Time Set-up with the PowerVIEW HD-22 or HD-30 QSR Systems .................................................................. 8
Image: PowerVIEW HD-22/30 Rear Panel Connections .................................................................................. 8
Drawing: Dip Switch and Resolution Label on the Bottom of the HD-22/30 ...................................................... 8
Quick-Connect SR Interface ...................................................................................................................................... 9
Image: Rear Panel with Feature Call-outs ........................................................................................................ 9
Before Installing: .................................................................................................................................................... 9
Installation Basics: ................................................................................................................................................... 10
General Installation Instructions for the CONCEAL Wall Mounting System: ....................................................... 10
Image: Basic Connectivity Example of the HD-22 or HD-30 ........................................................................... 12
Compliance and CE Declaration of Conformity - PowerVIEW HD-22 and HD30 ................................................... 13
Warranty Information ............................................................................................................................................... 14
General Specifications ......................................................................................................................................... 15
Appendix 1: Pin-Outs for the HD-22/30 Camera ................................................................................................... 15
Drawing: PowerVIEW HD-22/30 Dimensions ................................................................................................. 16
Communication Specification .................................................................................................................................. 16
HD-22/30 Command List (1/2) ......................................................................................................................... 17
HD-22/30 Command List (2/2) ......................................................................................................................... 18
HD-22/30 Inquiry List (1/1) ............................................................................................................................... 19
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 3 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
prop
O
VERVIEW
The impressive Vaddio PowerVIEW HD-22 and HD-30 high definition
PTZ cameras are available in the versatile Vaddio PowerVIEW QSR
(short range) package. The PowerVIEW HD-22 QSR and the
PowerVIEW HD-30 QSR feature 22X and 30X power zoom optics
respectively. These cameras use a 1MOS, 1/2.8-Type, progressive
scan image sensors, which provide for better light sensitivity,
increased noise reduction and lower power consumption than
cameras with either CCD or CMOS image sensors. This advanced
MOS image sensor captures vivid colors, delicate gradation and
realistic textures that are comparable to 3-chip camera performance.
Both the HD-22 and the HD-30 provide matchless low-light
capabilities with a minimum illumination rating of an amazing 0.4 lux
(color) and 0.3 lux (B/W). Equipped with a 2.2 megapixel MOS
sensor, the cameras deliver native 1080p/60 high definition video
resolution and superior color reproduction for use in any professional
A/V presentation, videoconferencing, House of Worship, education,
Image: PowerVIEW HD22 or HD-30 QSR System
with the CONCEAL Mount for and a clean installation.
live event and industrial applications.
The HD-22 has a powerful 22X multi-element glass zoom lens (f=4.3mm to 94.6mm) and works exceptionally in
large rooms. However, the premium optics also provides a super-wi de horizontal field of view of 65.2º, which works
very well in small room video applications. The HD-30, as one can imagine, has a robust 30X optical power zoom
lens that enables the capture of brilliant and detailed video images even in the largest rooms.
The cameras output multi-format HD video in both analog comp onent (YPbPr), HDMI and diff erential forma ts in HD
resolutions of 1080p/59.94, 1080p/50 1080p/29.97 1080p/25, 1080i/59.94, 1080i/50, 720p/59.94, 720p/50 and SD
resolutions of 480p/59.97 and 576p/50. Both cameras are offered in PowerVIEW QSR packages with the QuickConnect SR Interface, which uses HSDS™ for distribution of video, power and control over Cat-5 cable up to 100’
(30.48m). The PowerVIEW HD-22 and HD-30 cameras represent an exceptional value and are superb performers
for the most demanding video applications.
Intended Use:
Before operating the device, please read the entire manual thoroughly. The system was designed, built and tested
for use indoors with the power supply provided. The use of a power supply other than the one provided or outdoor
operation has not been tested and could damage the device and/or create a potentially unsafe operating condition.
Important Safeguards:
Read and understand all instructions before using. Do not operate any device if it has been dropped or
damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the risk of
electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.
Use only the power supply provided with the system. Use of any unauthorized
power supply will void any and all warranties.
Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not
work well for professional installations and can be the cause of intermittent conn ections which
can result in the RS-232 control line failing and locking up, and/or compromising the HSDS (high
speed differential) signals. For best results please use standard RJ-45 connectors and test all
cables for
er pin-outsprior to use and connection to Vaddio product.
Save These Instructions:
The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from
www.vaddio.com free of charge.
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 4 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
U
NPACKING
Carefully remove the product and all of the included parts from the packaging.
Identify the following parts for each camera:
PowerVIEW HD-22 QSR Camera System (North America):
Part Number: 999-6965-000
One (1) PowerVIEW HD-22 HD PTZ Camera (998-6960-000)
One (1) Vaddio IR Remote Commander
One (1) Quick-Connect SR Interface
One (1) 3-Position Phoenix-type Connector for IR Forwarding
One (1) 24 VDC, 2.0 A Power Supply with Power Cord for North America
One (1) CONCEAL Wall Mount with Mounting Hardware
One (1) EZCamera™ Control Adapter (RJ-45-F to DB-9-F)
Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
PowerVIEW HD-22 QSR Camera System (International):
Part Number: 999-6965-001
One (1) PowerVIEW HD-22 HD PTZ Camera (998-6960-000)
One (1) Vaddio IR Remote Commander
One (1) Quick-Connect SR Interface
One (1) 3-Position Phoenix-type Connector for IR Forwarding
One (1) 24 VDC, 2.0 A Power Supply
One (1) Euro Power Cable
One (1) UK Power Cable
One (1) CONCEAL Wall Mount with Mounting Hardware
One (1) EZCamera Control Adapter (RJ-45 to DB-9)
Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
PowerVIEW HD-30 QSR Camera System (North America):
Part Number: 999-6975-000
One (1) PowerVIEW HD-30 HD PTZ Camera (998-6970-000)
One (1) Vaddio IR Remote Commander
One (1) Quick-Connect SR Interface
One (1) 3-Position Phoenix-type Connector for IR Forwarding
One (1) 24 VDC, 2.0 A Power Supply with Power Cord for North America
One (1) CONCEAL Wall Mount with Mounting Hardware
One (1) EZCamera Control Adapter (RJ-45-F to DB-9-F)
Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
PowerVIEW HD-30 QSR Camera System (International):
Part Number: 999-6975-001
One (1) PowerVIEW HD-30 HD PTZ Camera (998-6970-000)
One (1) Vaddio IR Remote Commander
One (1) Quick-Connect SR Interface
One (1) 3-Position Phoenix-type Connector for IR Forwarding
One (1) 24 VDC, 2.0 A Power Supply
One (1) Euro Power Cable
One (1) UK Power Cable
One (1) CONCEAL Wall Mount with Mounting Hardware
One (1) EZCamera Control Adapter (RJ-45 to DB-9)
Quick Start Guide
Full Manuals are downloaded from support.vaddio.com
CONCEAL Mount includes:
Metal Bracket,
Bottom Cover
Rear Connector/Cable Cover
Mounting Hardware
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 5 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
Camera Front View with Feature Call-outs
Image: PowerVIEW HD-22/30 QSR Camera System
①
②
④
③
1) Camera and Zoom Lens:
The 22X (HD-22) or 30X (HD-30) optical zoom lens is built around a (1/2.8 Type) high-speed MOS image sensor
with a total of 2.2 megapixels for precise HD video image acquisition.
2) Red Tally Light:
A red tally light is illuminated when the camera receives a command from an external controller.
3) IR Sensors:
IR sensors are built into the front of the HD-22 and HD-30 to receive IR signals from the IR remote control
supplied with the camera.
4) Blue Power Light:
A Vaddio blue power light is illuminated when the camera is turned on.
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 6 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
Rear Panel Connections with Feature Call-outs
Image: PowerVIEW HD-22/30 QSR Camera System
⑤
⑥
⑨
⑩
⑦
⑪
⑧
5) RS-232 IN & IR Out:
The RS-232 port accepts modified VISCA protocol for camera control, as well as transmits IR signaling received
by the IR receivers, which can be transmitted to third party remotes.
6) Dip Switch Settings:
Settings for IR remote, baud rate and image flip can be configured on these switches. See the Switch Settings
page for additional information.
7) HD Video Select:
A rotary switch allows the user to choose the component HD output video resolution and format. See the Switch
Settings page for additional information.
HD Resolution Note: When changing the resolution of the came ra, the camera may need to be po wer-cycled
after the change. Pretty much every switcher will have to be reset or rebooted as well.
8) 12 VDC Input:
Power input for the standard HD-22 and HD-30 camera power supply (not used with QSR Kit).
9) HDMI Output:
The HDMI output feeds out HD digital video only (no copy protect or device communication is included). T he HDMI
output is optimized for HD video signals.
10) YPbPr Output:
Component HD video (YPbPr) is output through the DE-15 connector. YPbPr and HDMI signals are sim ultaneous.
Limited SD resolutions are supported.
11) EZ Power/Video Port:
This RJ-45 connector is used with the Quick-Connect SR Interface to supply power and return HSDS (differential)
video from the camera. Please mark and test cables for voltage prior to connection (see pin-out section).
12) Slot for Optional Cards:
The EZIM CCU slot card for the CCU can be plugged into the PowerVIEW HD-22 HD camera.
.
⑫
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 7 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
F
IRST TIME SET-UP WITH THE POWER
VIEW HD-22
OR
HD-30 QSR S
YSTEMS
The PowerVIEW HD-22 and HD-30 cameras in the QSR sy stem were designed to be very easy to use and o perate.
There is documentation at the back of this manual for pin-outs of the connectors.
Step 1: Using the HD VIDEO SELECT rotary switch and CAMERA SETTINGS dip switches on the back of the
camera, set up the camera’s output resolution and functional preferences. There is a label on the bottom of the
camera that identifies the choices.
Important Dip Switch Note: Setting all dip switches down and power cycling the camera will load the factory default camera settings. For the
first time set-up, loading the defaults may be a good idea.
Image: PowerVIEW HD-22/30 Rear Panel Connections
HD Video Select Switch
(Set HD resolution)
Camera Settings 10-Pos Dip Switch
(Set functional preferences)
HD-22/30 Rear Panel
Drawing: Dip Switch and Resolution Label on the Bottom of the HD-22/30
IR 1
1 & 2 UP
DIP SWITCH SETTINGS
IR
9600
bps
OFF
5
OUT
OFF
OFF
IMAGE
HDMI
6
COLOR
YCbCr
FLIP
OFF
OFF
9
10
OFF
IR 2ONIR 3
ON
12
21
ON
38400
bps
3
3
4
4
56
5
sRGB
ON
68109
8
7
7
910
VIDEO RESOLUTION SELECT
720p/59.94
0
1080i/59.94
1
1080p/59.94
2
3
720p/50
4
1080i/50
5
1080p/50
6
480p/59.94 1080p/25
7
8
9
A
B
C
D
E
F
576p/50
1080p/29.97
Setting the Camera:
a) Set the desired and available HD output resolution for the camera with the Rotary Switch.
b) Set the IR frequency of the camera if it is to respond to the IR remote control.
c) If using the IR forwarding feature, set the IR OUT switch to ON (SW3).
d) Set the Baud Rate dip switch (SW4) to 9600bps for most applications. Default for is 9600bps.
e) To set the HDMI or DVI color space, use dip switch 7 (SW7).
f) If inverting the camera, turn the IMAGE FLIP ON (SW8).
Dip Switch Settings:
IR 1 & 2: The IR remote has the capability of operating up to three different PTZ cameras from one remote. Use the
selector buttons at the top of the IR remote to select the frequency.
IR Out 3: The IR output is sent out on the RS-232 RJ-45 jack on the back of the camera. Turning on the IR output will
allow IR signals to be transmitted over the Cat-5 cable to the head end. When using RS-23 2 control or Vaddio CCU
controllers (also via RS-232), turn the IR OUT to OFF (up).
Baud Rate 4: The options for baud rate are either 9600 bps or 38,400 bps.
HDMI Color or sRGB Color space 7: Default is YCbCr. Use sRGB color space with older DVI-D 1.0 monitors only. The
YCbCr color space is best for HDMI digital video.
Image Flip 8: To invert the HD-20, turn the IMAGE FLIP ON (switch down).
Switches 9 and 10: Leave up - or in the OFF position.
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 8 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
Q
UICK-CONNECT SR INTERFACE
Image: Rear Panel with Feature Call-outs
1) Power Input:
5.5mm OD x 2.5mm ID coaxial connector for the provided 24 VDC, 2.0 Amp switching power supply.
2) EZ-POWER VIDEO Port (Color Coded Orange):
A single Cat-5 connection between the EZCAMERA POWER & HD VIDEO RJ-45 connector and the camera’s EZ
Power HD Video Port on the HD-19 camera extends power and video. Power is fed to the camera and HSDS
video is returned from the camera on the same Cat-5.
3) HD Video Output:
DE-15 connector outputs the YPbPr analog component HD video, which was e xtended fro m the cam era o ver Cat 5 cable. SD video resolutions (Y/C and CVBS formats) are not supported by the Quick-Connect SR Interface,
however analog component SD (high fps format - 480p/59.94 and 576p/50) video is supported.
4) IR Output:
With the IR pass-thru turned ON (see camera dip switch settings), IR from third-party IR remote controls can be
sent through the camera to third-party equipment, such as hardware videoconferencing codecs. IR can be used
as either modulated (through the air) or non-modulated (wired) signals).
5) RS-232 INPUT (Color Coded Grey) and OUT TO CAMERA (Color Coded Blue) Jacks:
These RJ-45 connectors allow an external controller (look-out for upcoming shameless plug) like the
ProductionVIEW™ Precision Camera Controller to route through the Quick-Connect SR for ease of cable routing.
Before Installing:
Choose camera mounting location, paying close attention to camera viewing angles, lighting conditions,
possible line of site obstructions, and checking for in-wall obstructions where the camera is to be mounted.
Always pick a mounting location that will optimize the performance of the camera.
The wall mount for the PowerVIEW system can be mounted directly to a 2-gang wall box or can be mounted
using only dry wall anchors.
For Power/Video and RS-232 signals, use standard Cat-5 cable (568B termination with real RJ-45 connectors)
from the EZ-POWER VIDEO and RS-232 ports on the back of the camera to the Quick-Connect SR Interface
(see install instructions).
①
②
③
④
⑤
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 9 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
I
NSTALLATION BASICS:
The PowerVIEW QSR system was specifically designed for installation on a vertical surface with
Cat-5 cable connectivity for Video, Power and Control signaling (two Cat-5 cables are required).
Installation is simplified in that no custom 8-Pin mini-din cables or expensive plenum coax cables o r
multi-pin cables are needed and no power outlets are required near the camera bracket. All cabling
is routed to the head-end using Cat-5 cables with standard straight t hrough RJ-45 conne ctors (568B
termination). “Pass-thru” type RJ-45 connectors should be avoided, like ka rate on top of a ladder.
General Installation Instructions for the CONCEAL Wall Mounting System:
Step 1: Determine Camera Mount Location
When locating the camera, consider viewing angles, lighting conditions, possible line of site obstru ctions and check
for in-wall obstructions where the camera is to be mounted. Pick a mounting location to optimize the performance
of the camera. After determining the optimum location of the camera system, route both of the required Cat-5
cables from the camera to the head-end. Mark the cables Power/Video and RS-232 accordingly.
Both Cat-5 cables should feed-through a 1” (25.4mm) opening (circular or square shape) centered in the
rectangular slot located on the rear flange of the CONCEAL Wall Mount Bracket.
Note: Do not cut out the entire rectangular slot opening in the wall! This will not allow the two lower wall
anchors to correctly fasten the CONCEAL bracket to the wall.
If the bracket is to be mounted on a 2-gang wall box, use the screws supplied with the wall box cover plate to attach
the CONCEAL Wall Mount Bracket. If mounting to drywall with wall anchors, use the four (4) quality wall
anchors/screws provided.
Note: The mounting holes are slotted and are 90° opposing to provide easy leveling. Level the mount and tighten
the mounting screws. The example of the CONCEAL mount shows an HD-USB, but the steps are identical for the
HD-22 or HD-30.
CONCEAL Wall Mount Bracket:
Cabled and Attached to Wall
Camera aligned and attached to the
CONCEAL Wall Mount Bracket (by
two-(1/4”-20) screws in the bottom of
the mount).
Note: Check all Cat-5 cables for continuity in advance of final connection. Plugging the POWER/VIDEO
Cat-5 cable into the wrong RJ-45 may cause damage to the camera system and void the warranty!
Step 2: System Wiring
Follow the sample wiring diagrams for connecting the Cat-5 cables to the camera and Quick-Co nnect SR Interface.
Additional diagrams are available on the Vaddio website.
Connect the camera side as follows:
Connect the Power/Video Cat-5 to the EZ POWER HD VIDEO RJ-45 jack on the back of the camera.
Connect the RS-232 Control Cat-5 to the “RS-232 IN” RJ-45 on the camera.
Connect the Quick-Connect SR side as follows:
Connect the Power/Video Cat-5 to the EZCAMERA POWER & HD VIDEO RJ-45 jack
Connect the RS-232 Cat-5 cable to the RS-232 OUTPUT and route the controller to the RS-232 input.
The controller can be routed directly to the camera if preferred. For IR Forwarding, the RS-232 cable
must be routed through the Quick-Connect SR in order to operate correctly (see pin-out section)
Wait to connect the power supply until later.
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 10 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
Step 3: Secure the Camera To the CONCEAL Wall Mount Bracket
After all cables are attached to the camera, place the camera onto the camera mount and insert the two 1/4”-20
screws into the camera through the two-screw slots in the bottom of the mount. Note: Be sure to align each side
of the camera evenly for the best fit prior to tightening the mounting screws.
Step 4: Install the CONCEAL Lower Cover Plate
Attach the CONCEAL lower cover plate. Slide the lower cover plate from front of the mounting bracket toward the
rear of the bracket. The two (2) rear locking tabs will need to be guided into position first and will lock in place as
the lower cover plate is pushed toward the rear of the mounting bracket. The two (2) front tabs will engage as the
cover is pushed back into place.
CONCEAL Lower Cover Plate
with Locking Tabs
CONCEAL Lower Cover
Plate locked in place
Step 5: Install the CONCEAL Rear Camera Cover
Install the CONCEAL rear camera cover on the mounting bracket with the supplied screw.
CONCEAL Rear Camera Cover
Completed CONCEAL Wall Mount
Camera Bracket Installation
NOTE (One more time!): Verify that the Cat-5 cables are plugged in correctly. Plugging the
Power/Video cable into the wrong RJ-45 jack may cause damage to the camera system and
void the warranty.
Step 6: Connect System Power
Connect the 24 VDC power supply to the Quick-Connect SR Interface and to an AC outlet. The SR will power the
camera via the Power/Video Cat-5 cable. The camera will “Home” to a centered position and will output video when
it has completely booted up. The PowerVIEW camera is now ready for control information from the contro ller or IR
Remote Commander.
A Note on Boot Order: When using a joystick controller or external control system, in order to
ensure proper continuity of control and operation of the cameras, the RS-232 controller should
be powered-on after the camera. In most, if not all cases, the camera needs to be on and
running in order for communication to take place between the camera and controller. When
plugging a new camera into a RS-232 controller/joystick that has already been powered up, a
system reboot or camera rescan may be necessary to find the camera.
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 11 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
(
)
Image: Basic Connectivity Example of the HD-22 or HD-30
Camera Connected to Quick-Connect SR Interface, ProductionVIEW™ Precision Camera Controlle r and Monitor
Rear View of HD-22 or
HD-30 PTZ Camera
Two (2) Cat-5/5e/6
Cables between
Camera and the
Quick-Connect SR
Up to 100’ (30.48m)
CONCEAL Mount
Not Shown
RS-232
blue to blue
Power/ Video
Cat5e
RS-232
Cat-5e
Quick-Connect
SR Interface
←
HSDS Differential Video (orange to orange)
Power
→
Rear Panel View
Quick-Connect
SR Interface
24VDC, 2.0 A
Power Supply
HD Video
YPbPr Format
RS-232
Cat-5
.
(Really Simulated Llama Farm Video)
HD Monitor
ProductionVIEW Precision Camera Controller
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 12 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
C
OMPLIANCE AND CE DECLARATION OF CONFORMITY - POWER
Compliance testing was performed to the following regulations:
FCC Part 15 (15.107, 15.109), Subpart B Class A
ICES-003, Issue 4: 2004 Class A
EN 55022 A: 2006 + A1: 2007 Class A
KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) Class A
KN22 2008 (CISPR 22: 2006) Class A
EMC Directive 2004/108/EC Class A
EN 55024: A2: 2003
Class A
VIEW HD-22
AND
HD30
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his/her own
expense.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device
must accept any interference including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the
user’s authority to operate this equipment.
ICES-003 Compliance
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le
ministère des Communications du Canada.
European Compliance
This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures.
Standard(s) To Which Conformity Is Declared:
EMC Directive 2004/108/EC
Class A
Immunity
EN 55022 A: 2006 + A1: 2007(CISPR 22:2005/A1:2005)
EN 55024: 1998 + Amendments A1: 2001 + A2: 2003
EN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001 Electrostatic Discharge
EN 61000-4-3: 2006 + A1: 2008 Radiated Immunity
EN 61000-4-4: 2004 + Corrigendum 2006 Electrical Fast Transients
EN 61000-4-5: 2006 Surge Immunity
EN 61000-4-6: 2009 Conducted Immunity
EN 61000-4-8: 2010 Power Frequency Magnetic Field
EN 61000-4-11: 2004 Voltage Dips, Interrupts and Fluctuations
KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) IT Immunity Characteristics
EN 61000-4-2 Electrostatic Discharge
EN 61000-4-3 Radiated Immunity
EN 61000-4-4 Electrical Fast Transients
EN 61000-4-5 Surge Immunity
EN 61000-4-6 Conducted Immunity
EN 61000-4-8 Power Frequency Magnetic Field
EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations
IEC 60950-1:2005 (2nd Edition); Am 1:2009
EN 60950-1:2006+A11:2009+A1:2010+A12:2011
Safety
Safety
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 13 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
WARRANTY INFORMATION
(See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details):
Hardware* Warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured products. Vaddio warrants
its manufactured products against defects in materials and workmanship for a period of two years from the day of purchase, to
the original purchaser, if Vaddio receives notice of such defects during the warranty. Vaddio, at its option, will repair or replace
products that prove to be defective. Vaddio manufactures its hardware products from parts and components that are new or
equivalent to new in accordance with industry standard practices.
Exclusions: The above warranty shall not apply to defects resulting from improper or inadequate maintenance by the customer,
customers applied software or interfacing, unauthorized modifications or misuse, mishandling, operation outside the normal
environmental specifications for the product, use of the incorrect power supply, modified power supply or improper site operation
and maintenance. OEM products and products manufactured by other companies are excluded and are covered by the
manufacturer’s warranty.
Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under
warranty. If the product is out of warranty, Vaddio will test then repair the product or products. T he cost of parts and labor
charge will be estimated by a technician and confirmed by the customer prior to repair. All compon ents must be returned for
testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.
Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs and/or
replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at
support@vaddio.com or online at vaddio.com.
Return Material Authorization (RMA) Number: Before returning a product for repair or replacement request an RMA from
Vaddio’s technical support. Provide the technician with a return phone number, e-mail address, shipping address, product serial
numbers and original purchase order number. Describe the reason for repairs or returns as well as the date of purchase. See
the General RMA Terms and Procedures section for more information. RMA’s are valid for 30 days and will be issued to Vaddio
dealers only. End users must return products through Vaddio dealers. Include the assigned RMA number in all correspondence
with Vaddio. Write the assigned RMA number clearly on the shipping label of the box when returning the product. All products
returned for credit are subject to a restocking charge without exception.
Voided Warranty: The warranty does not apply if the original serial number has been removed or if the product has been
disassembled or damaged through misuse, accident, modifications, use of incorrect po wer supply, use of a modified power
supply or unauthorized repair.
Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any
responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and insurance
charges for all items under warranty but will not assume responsibility for loss and/or damage by the outbound frei ght carrier.
If the return shipment appears damaged, retain the original boxes an d packing material for inspection b y the carrier. Contact
your carrier immediately.
Products not under Warranty: Payment arrangements are required before outbound shipment for all out of warranty products.
Other General Information:
Care and Cleaning
Do not attempt to take this product apart at any time. There are no user-serviceable components inside.
Do not spill liquids in the product
Keep this device away from food and liquid
For smears or smudges on the product, wipe with a clean, soft cloth
Use a lens cleaner on the lens - not a scratchy hanky
Do not use any abrasive chemicals.
Operating and Storage Conditions:
Do not store or operate the device under the following conditions:
Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)
High humi dit y, condensing or wet environments
In inclement weather
In swimming pools or garden waterfalls
Dry environments with an excess of static discharge
In orbit (space junk issue)
Under severe vibration
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 14 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
GENERAL SPECIFICATIONS
Camera PowerVIEW HD-22 PTZ PowerVIEW HD-30 PTZ
Part Numbers 999-6960-000 (North America)
Zoom 22X Optical Zoom 30X Optical Zoom
Field of View Horizontal: 65.2º Wide End to 3.1º Tele
Lens Focal Length f=4.3 mm to 94.6 mm / F1.6 - F4.7 f=4.3mm to 129.0 mm / F1.6- F4.7
Image Sensor 1/2.8-Type MOS, 2.2 Megapixel, Progressive Scan
Minimum Illumination Color: 0.4 lux (F1.6, 1/30 sec, 50 IRE, Gain: High),
Video Resolutions HD: 1080p/59.94, 1080p/50, 1080p/29.97/25, 1080i/59.94, 1080i/50, 720p/59.94, 720p/50
Video Output Formats HDMI (YCbCr for HDMI and sRGB for DVI), Analog Component (YPbPr)
Signal to Noise Ratio > 50 dB (AGC: Off)
PowerVIEW HD-22/30
QSR Quick-Connect
Pan Range Pan: +170 degrees to -170 degrees
Preset Positions 16 (internal), 6 recalled via Vaddio IR Remote Commander
Image Control Red & Blue Gain, Detail, Chroma, Gamma, Pedestal, Iris, and Gain
Tally Light Available through RS-232 Control
HD Video Select 16-Position Rotary Switch: Used to set HD Video Resolution Output
Camera Settings 10-Position Dip Switch: Settings for IR Select, Baud Rate 9600, Image Flip, Unpublished Functions
Accessory Slot Cards EZIM CCU Slot Card PN# 999-6900-006 - For Use with Quick-Connect Universal CCU Only
Dimensions/Weight 7.81” (198.37mm) H x 6.67” (169.42mm) W x 7.057” (179.25. mm) D / 5.6 lbs. (2.630835643 kg.)
999-6960-001 (Int’l)
(16:9 Aspect Ratio)
B/W: 0.04 lux (F1.6, 1/30 sec, 50 IRE, Gain: High)
SD: 480p/59.97 and 576p/50
HSDS (Power, Differential HD Video & R$S-232 Control)
Quick-Connect SR
Part Number 998-1105-016
Tilt: +90 degrees to -30 degrees
(Controls available through RS-232 control and Quick-Connect CCU and Slot Card)
999-6970-000 (North America)
999-6970-001 (Int’l)
Horizontal: 65º Wide End to 2.2º Tele
(16:9 Aspect Ratio)
Quick-Connect SR Interface
Connectors
Power Supply
Dimensions
(H x W x D)
Accessory
Moon in Front Page Header: Ariel - Moon of the planet Uranus.
Power Connector: 5.5mm OD, 2.5mm ID coaxial connector
Power/Video RJ-45: Supplies power to, and differential HD video from the camera
Video Output: DE-15 connector for HD Analog Component (YPbPr) video only (No SD Support)
IR Output: Transmits modulated or non-modulated IR signals - from the camera’s IR receiver
RS-232 IN RJ-45: Accepts RS-232 from ProductionVIEW or other external control systems
RS-232 OUT RJ-45: Sends RS-232 from Quick-Connect SR to the camera
24 VDC, 2.08 Amp Switching Power Supply
1/3 Rack Size
1.6” (40.64mm ) H x 5.5” (139.7mm) W x 3.25” (82.5500000000001mm) D
Rack Mount Adapter: 998-6000-002 - Holds three (3) Quick-Connect SR Interfaces
APPENDIX 1: PIN-OUTS FOR THE HD-22/30 CAMERA
Pin YPbPr
1 Pr
2 Y
3 Pb
4 5 6 Pr GND
7 Y GND
8 Pb GND
9 10 11 12 13 14 15 -
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 15 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
V
EZCamera Power & HD Video RJ-45 Connector Pin-outs
Important Note: The EZ POWER HD VIDEO RJ-45 Connector is for use with the Quick-Connect SR,
Quick-Connect DVI/HDMI SR and Quick-Connect USB Interfaces ONLY (568B Wiring Standard). The
video signals are differential (HSDS™) and can only be received by the interfaces above.
RS-232, IR OUT on Camera HD-22/30 - RJ-45
Pin Signal
1 Power+
2 Power-
3 Y+
4 PB+
5 PB GND
6 Y GND
7 PR+
8 PR-
EZ-POWER
IDEO
12345678
Pin # Function
Pin - 1 N/A
Pin - 2 N/A
Pin - 3 N/A
Pin - 4 IR Output (Diff Signal to Quick-Connect SR)
Pin - 5 IR Ground (Diff Signal to Quick-Connect SR)
Pin - 6 Digital GND
Pin - 7 RXD (from TXD of control source)
Pin - 8 TXD (to RXD of control source)
Drawing: PowerVIEW HD-22/30 Dimensions
‘
RS-232
IR OUT
12345678
RJ-45 Jack
on Camera
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 16 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
COMMUNICATION SPECIFICATION
Communication Speed: 9600 bps (default)
Start bit: 1
Stop bit: 1
Data bits: 8
Parity: None
No Flow control
12345678
Pin # RJ-45 RS-232 and IR Out Pins
1) Unused
2) Unused
3) Unused
4) IR Output (Diff Signal to Quick-Connect SR)
5) IR Ground (Diff Signal to Quick-Connect SR)
6) GND (GND of IR Short Range - Pin 3)
7) RXD (from TXD of control source)
8) TXD (to RXD of control source)
NOTE: The Vaddio PowerVIEW HD-22 and 30Control Protocol is similar, but not identical to, the Sony® VISCA™
command set in order to be compatible with several popular control devices. Not all VISCA commands are
supported and there are many HD-22/30 specific commands in the following Command and Inquiry Lists.
HD-22/30 Command List (1/2)
Command Set Command Command Packet Comments
Address Set Broadcast 88 30 01 FF Address Set (Daisy chain)
IF_Clear Broadcast 88 01 00 01 FF IF Clear
Command Cancel 8x 2p FF p:socket number(1,2)
CAM_Power On
Off(Standby)
CAM_Zoom Stop
Tele(Standard)
Wide(Standard)
Tele(Variable)
Wide(Variable)
Direct
CAM_Focus Stop
Far(Standard)
Near(Standard)
Far(Variable)
Near(Variable)
AutoFocus
ManualFocus
Auto/Manual
Direct
CAM_WB Auto
Indoor
Outdoor
One Push WB
Manual
Fluorescent
One Push Trigger
CAM_RGain Reset
Up
Down
Direct
CAM_BGain Reset
Up
Down
Direct
CAM_AE Full Auto
Manual
CAM_Iris Reset
Up
Down
Direct
CAM_Gain Reset
Up
Down
Direct
CAM_Backlight On
Off
CAM_Aperture Reset
Up
Down
Direct
8x 01 04 00 02 FF
8x 01 04 00 03 FF
8x 01 04 07 00 FF
8x 01 04 07 02 FF
8x 01 04 07 03 FF
8x 01 04 07 2p FF
8x 01 04 07 3p FF
8x 01 04 47 00 0p 0q 0r FF
8x 01 04 08 00 FF
8x 01 04 08 02 FF
8x 01 04 08 03 FF
8x 01 04 08 2p FF
8x 01 04 08 3p FF
8x 01 04 38 02 FF
8x 01 04 38 03 FF
8x 01 04 38 10 FF
8x 01 04 48 0p 0q 0r 0s FF
8x 01 04 35 00 FF
8x 01 04 35 01 FF
8x 01 04 35 02 FF
8x 01 04 35 03 FF
8x 01 04 35 05 FF
8x 01 04 35 06 FF
8x 01 04 10 05 FF
8x 01 04 03 00 FF
8x 01 04 03 02 FF
8x 01 04 03 03 FF
8x 01 04 43 00 00 0p 0q FF
8x 01 04 04 00 FF
8x 01 04 04 02 FF
8x 01 04 04 03 FF
8x 01 04 44 00 00 0p 0q FF
8x 01 04 39 00 FF
8x 01 04 39 03 FF
8x 01 04 0B 00 FF
8x 01 04 0B 02 FF
8x 01 04 0B 03 FF
8x 01 04 4B 00 00 0p 0q FF
8x 01 04 0C 00 FF
8x 01 04 0C 02 FF
8x 01 04 0C 03 FF
8x 01 04 4C 00 00 0p 0q FF
8x 01 04 33 02 FF
8x 01 04 33 03 FF
8x 01 04 02 00 FF
8x 01 04 02 02 FF
8x 01 04 02 03 FF
8x 01 04 42 00 00 0p 0q FF
Power On/Off
p:(1-Slow to 4-Fast)
p:(1-Slow to 4-Fast)
pqr: Zoom Position*
p:(1-Slow to 4-Fast)
p:(1-Slow to 4-Fast)
pqrs: Focus position(0-0x438)*
Normal Auto (Auto Tracing WB)
Indoor Mode (Color Temp 3200K)
Outdoor Mode (Color Temp 5600K)
One Push White Balance Mode
Manual White Balance
Fluorescent(Color Temp 4200K)
One Push WB Trigger
pq:00-ff
pq:00-ff
Auto Exposure Mode
Manual Control Mode
pq(0x00-0xFF)
pq(0x00-0xFF)
pq(0x00-0x3F)
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 17 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
HD-22/30 Command List (2/2)
Command Set Command Command Packet Comments
CAM_Memory Reset
Set
Recall
CAM_IDWrite 8x 01 04 22 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFFF
CAM_LR_Reverse On
Off
CAM_Freeze On
Off
CAM_PictureEffect Color
B&W
Pan-tiltDrive Up
Down
Left
Right
UpLeft
UpRight
DownLeft
DownRight
Stop
Absolute Position
Home
Reset
Tally On
Off
Preset Pan Speed Pan/Tilt/Zoom Speed 81 01 7E 01 0B WW SS ZZ FF WW: Pan Speed (0x01-0x18)
Motor Config Hard Motor Stops
Soft Motor Stops
BLK.Enhance Pedestal 8x 01 7E 53 00 00 0p 0q FF Pq: Pedestal(0x00-0xFF)
GMA.Enhance Gamma 8x 01 7E 54 00 00 0p 0q FF pq: Gamma (0x00-0x03)
CRM.Enhance Chroma 8x 01 7E 55 00 00 0p 0q FF pq: Chroma (0x00-0xFF)
KNE.Enhance Knee No Support No Support
DIS.Enhance Digital Image
Stabilizer
DNR.Enhance Digital Noise
Reduction
AGC.Enhance AGC Mode 8x 01 7E 59 00 FF
CAM_ICR ICR On
ICR Off
8x 01 04 3F 00 0p FF
8x 01 04 3F 01 0p FF
8x 01 04 3F 02 0p FF
8x 01 04 61 02 FF
8x 01 04 61 03 FF
8x 01 04 62 02 FF
8x 01 04 62 03 FF
8x 01 04 63 00 FF
8x 01 04 63 04 FF
8x 01 06 01 VV WW 03 01 FF
8x 01 06 01 VV WW 03 02 FF
8x 01 06 01 VV WW 01 03 FF
8x 01 06 01 VV WW 02 03 FF
8x 01 06 01 VV WW 01 01 FF
8x 01 06 01 VV WW 02 01 FF
8x 01 06 01 VV WW 01 02 FF
8x 01 06 01 VV WW 02 02 FF
8x 01 06 01 VV WW 03 03 FF
81 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
8x 01 06 04 FF
81 01 06 05 FF
8x 01 7E 01 0A 00 02 FF
8x 01 7E 01 0A 00 03 FF
8x 01 7E 01 70 00 00 FF
8x 01 7E 01 70 00 01 FF
8x 01 7E 57 02 FF
8x 01 7E 57 03 FF
8x 01 7E 58 02 FF
8x 01 7E 58 03 FF
8x 01 7E 59 01 FF
8x 01 7E 59 02 FF
8x 01 7E 59 03 FF
8x 01 7E 59 04 FF
8x 01 7E 59 05 FF
8x 01 7E 59 06 FF
8x 01 7E 59 07 FF
8x 01 7E 59 00 0p FF
8x 01 04 01 02 FF
8x 01 04 01 03 FF
p:Memory No(=0-0xF)
Mirror (Horizontal) on
Mirror (Horizontal) off
Still image on
VV: Pan Speed (0x01-0x18)
WW: Tilt Speed(0x01-0x14)
YYYY: Pan Position**
ZZZZ: Tilt Position**
SS:Tilt Speed(0x01-0x14)
ZZ:Zoom Speed(0-7);
On
Off
On
Off
Off Manual AGC Gain (0dB)
Low
Medium
High
Low1
Low2
Med1
High1
Off p: Manual AGC Gain(1-0x0e)***
ICR On – Cut filter out B&W
ICR Off – Cut filter in Color
*Zoom and Focus Data:
CAM_Zoom: Range (0x000–0xA23/0xA73) HD22:0xA23(22x Zoom), HD30: 0xA73(30x Zoom)
CAM_Focus: Range (0x000-0x438) dependent on Zoom Position
**Additional Information:
Pan Range: 8044 – 7FBC (-32,700 to +32,700)
Tilt Range: E891 – 4C2B (-5,999 to +19,499)
Actual Pan/Tilt ranges defined in Inquiry list
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 18 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
HD-22/30 Inquiry List (1/1)
Inquiry Command Command Response Packet Comments
CAM_PowerInq 8x 09 04 00 FF y0 50 02 FF
CAM_ICRModeInq 8x 09 04 01 FF y0 50 02 FF
CAM_BacklightModeInq 8x 09 04 33 FF y0 50 02 FF
CAM_WBModeInq 81 09 04 35 FF y0 50 00 FF
CAM_AEModeInq 8x 09 04 39 FF y0 50 00 FF
CAM_LR_Reverse 8x 09 04 61 FF y0 50 02 FF
CAM_Freeze 8x 09 04 62 FF y0 50 02 FF
CAM_PictureEffect 8x 09 04 63 FF y0 50 00 FF
CAM_MemoryInq 8x 09 04 3F FF y0 50 0p FF p:Preset 0-0xf
CAM_IDInq 8x 09 04 22 FF y0 50 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFFF
CAM_ApertureInq 8x 09 04 42 FF y0 50 00 00 0p 0q FF Pq:x00-0x3F
CAM_RGain 8x 09 04 43 FF y0 50 00 00 0p 0q FF pq:000-0ff
CAM_BGain 8x 09 04 44 FF y0 50 00 00 0p 0q FF pq:000-0ff
CAM_ZoomPosInq 8x 09 04 47 FF y0 50 0p 0q 0r 0s FF pqr: 0-0x6B3
CAM_FocusPosInq 8x 09 04 48 FF y0 50 0p 0q 0r 0s FF pqrs: Focus Position
CAM_FocusModeInq 8x 09 04 38 FF y0 50 02 FF
CAM_Iris 8x 09 04 4B FF y0 50 00 00 0p 0q FF pq(0x00-0xFF)
CAM_Gain 8x 09 04 4C FF y0 50 00 00 0p 0q FF pq(0x00-0x24)
IR_ReceiveInq 8x 09 06 08 FF y0 50 02 FF
Pan-TiltMaxSpeedInq 8x 09 06 11 FF y0 50 pp qq FF pp:Pan 0x01-0x18
Pan-tiltPositionInq 8x 09 06 12 FF FF y0 50 0p 0p 0p 0p 0q 0q 0q 0q FF pppp: Pan 0x8044-0x7FB2
CAM_ShutterPosInq No support No support Shutter Position
TallyInq 8x 09 7E 01 0A FF y0 50 02 FF
PresetSpeedInq 8x 09 7E 01 0B FF y0 50 pp qq rr FF pp:Pan 0x01-0x18
Motor Config 8x 09 7E 01 70 FF y0 50 00 FF
BLK.Enhance 8x 09 7E 53 FF y0 50 00 00 0p 0q FF pq: Pedestal(0x00-0xFF)
GMA.Enhance 8x 09 7E 54 FF y0 50 00 00 00 0p FF p: Gamma (0x00-0x03)
CRM.Enhance 8x 09 7E 55 FF y0 50 00 00 0p 0q FF p: Chroma (0x00-0xFF)
DIS.Enhance 8x 09 7E 57 FF y0 50 02 FF
DNR.Enhance 8x 09 7E 58 FF y0 50 02 FF
AGC.Enhance 8x 09 7E 59 FF
8x 09 7E 59 00 FF
y0 50 03 FF
y0 50 03 FF
y0 50 03 FF
y0 50 01 FF
y0 50 02 FF
y0 50 03 FF
y0 50 05 FF
y0 50 06 FF
y0 50 03 FF
y0 50 03 FF
y0 50 03 FF
y0 50 04 FF
y0 50 03 FF
y0 50 03 FF
y0 50 03 FF
y0 50 01 FF
y0 50 03 FF
y0 50 03 FF
y0 50 00 FF
y0 50 01 FF
y0 50 02 FF
y0 50 03 FF
y0 50 04 FF
y0 50 05 FF
y0 50 06 FF
y0 50 07 FF
y0 50 0p FF
On
Off(Standby)
On - ICR filter Out
Off – ICR filter In
On
Off
Auto
Indoor
Outdoor
One Push WB
Manual
Fluorescent
Auto Exposure Mode
Manual Control Mode
On
Off
On
Off
Off
B&W
Auto
Manual
On
Off
qq:Tilt 0x01-0x14
qqqq: Tilt 0xE890-0x4C2C
On
Off
qq:Tilt 0x01-0x14
rr:Zoom 0x00-0x07
Hard Motor Stops
Soft Motor Stops
On
Off
On
Off
Off Manual AGC Gain(0dB)
Low
Medium
High
Low1
Low2
Med1
High1
Off p: Manual AGC Gain(0-0x0e)***
***Manual AGC Gain: 0:0dB, 1:3dB, 2:6dB, 3:9dB, 4:12dB, 5:15dB, 6:18dB, 7:21dB, 8:24dB, 9:27dB, 10:30dB, 11:33dB,
12:36dB, 13:39dB & 14:42dB
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 19 of 20
PowerVIEW HD-22 and HD-30 QSR Systems
Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464
©2015 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are
subject to change without notice or obligation. Vaddio, PowerVIEW, ProductionVIEW, EZCamera, Quick-Connect and HSDS are trademarks
PowerVIEW HD-22 QSR and HD-30 QSR Cameras Systems - Document Number 342-0643 Rev D Page 20 of 20
of Vaddio. All other trademarks are property of their respective owners. Document Number 342-0643 Rev D, SD: 68670.0
www.vaddio.com
Loading...