Unimac UWN160T4V Owner’s Manual

Washer-Extractors

PHM1429C_SVG

Pocket Hardmount

UniLinc and M30 Control

Refer to Page 9 for Model Identification

Installation/Operation/Maintenance

Original Instructions Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.alliancelaundry.com

Part No. F8410701ENR13

May 2017

Safety Information..................................................................................5

Explanation of Safety Messages....................................................................... 5

Important Safety Instructions........................................................................... 5

Safety Decals................................................................................................. 7

Operator Safety.............................................................................................. 7

Introduction........................................................................................... 8

Model Identification........................................................................................8

Delivery Inspection.........................................................................................8

Serial Plate Location....................................................................................... 8

Replacement Parts ......................................................................................... 9

Customer Service............................................................................................9

Manufacturing Date........................................................................................ 9

Specifications and Dimensions.............................................................. 10

Specifications and Dimensions.......................................................................10

Machine Dimensions ....................................................................................13

Mounting Bolt Hole Locations - 45 and 65 Pound Models................................ 16

Mounting Bolt Hole Locations - 85 and 105 Pound Models.............................. 18

Mounting Bolt Hole Locations - 130 and 160 Pound Models.............................20

Floor Layout............................................................................................. 22

Mounting Bolt Pattern................................................................................25

Single Machine Foundation Requirements.......................................................25

Machine Installation on Existing Floor........................................................ 26

Elevated Pad Installation on Existing Floor..................................................27

New Foundation........................................................................................27

Isolated Pad Installation............................................................................. 27

Machine Foundation and Pad Installation........................................................ 28

Machine Installation......................................................................................29

Machine Mounting and Grouting....................................................................32

Floor Load Data............................................................................................35

Drain Connection Requirements.....................................................................36

Water Connection......................................................................................... 38

Plumbing Diagrams.......................................................................................41

Electrical Installation Requirements................................................................44

North American Approval..........................................................................46

CE Approval.............................................................................................53

Steam Requirements (Steam Heat Option Only)...............................................59

Chemical Injection Supply System................................................................. 59

Connecting External Liquid Supplies with Five Compartment Supply Dispenser

(Optional)............................................................................................. 62

Copyright 2017, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.

DO NOT COPY or TRANSMIT

3 Part No. F8410701ENR13

External Supplies..........................................................................................63

Chemical Injection Using Internal 24VAC Control Transformer.....................64

Chemical Injection Using External AC Power Source................................... 64

External Supply Signals............................................................................. 65

Operation............................................................................................. 67

Operating Instructions for UniLinc Control..................................................... 67

Shakeout Routine...................................................................................... 69

Basket Jog Feature (160 Pound Models Only)..............................................69

Operating Instructions for M30 Control.......................................................... 70

Shakeout Routine...................................................................................... 72

Start Up................................................................................................73

Basket Rotation............................................................................................ 73

Safety Stability Switch Operation............................................................... 73

Maintenance......................................................................................... 74

Maintenance.................................................................................................74

Daily........................................................................................................... 74

Beginning of Day...................................................................................... 74

End of Day............................................................................................... 75

Monthly....................................................................................................... 75

Yearly..........................................................................................................76

Care of Stainless Steel...................................................................................77

Disposal of Unit.................................................................................... 79

Disposal of Unit............................................................................................79

China Restriction of hazardous substances (RoHS)............................... 80

DO NOT COPY or TRANSMIT

4 Part No. F8410701ENR13

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.

DANGER

Indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.

WARNING

Indicates a hazardous situation that, if not avoided, could cause severe personal injury or death.

CAUTION

Indicates a hazardous situation that, if not avoided, may cause minor or moderate personal injury or property damage.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed.

NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.

Important Safety Instructions

WARNING

To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer, follow these basic precautions:

W023

• Read all instructions before using the washer.

• Install the washer according the INSTALLATION instructions. Refer to the EARTH/GROUND instructions in the IN-

STALLATION manual for the proper earth/ground connection of the washer. All connections for water, drain, electrical power and earth/ground must comply with local codes and be made by licensed personnel when required. It is recommended that the machine be installed by qualified technicians.

• Do not install or store the washer where it will be exposed to water and/or weather.

• To prevent fire and explosion, keep the area around machine free from flammable and combustible products. Do not add the following substances or textiles containing traces of the following substances to the wash water: gasoline, kerosene, waxes, cooking oils, vegetable oils, machine oils, dry-cleaning solvents, flammable chemicals, thinners, or other flammable or explosive substances. These substances give off vapors that could ignite, explode or cause the fabric to catch fire by itself.

• Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing machine or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable, do not smoke or use an open flame during this time.

• To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the washer to the electrical power source.

• Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. This appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. This is a safety rule for all appliances.

• DO NOT reach and/or climb into the tub or onto the washer, ESPECIALLY if the wash drum is moving. This is an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.

• Never operate the washer with any guards, panels and/or parts removed or broken. DO NOT bypass any safety devices or tamper with the controls.

• Use washer only for its intended purpose, washing textiles. Never wash machine parts or automotive parts in the machine. This could result in serious damage to the basket or tub.

• Use only low-sudsing, no-foaming types of commercial detergent. Be aware that hazardous chemicals may be present. Wear hand and eye protection when adding detergents and chemicals. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or

DO NOT COPY or TRANSMIT

5 Part No. F8410701ENR13

Safety Information

chemical burns, keep them out of the reach of children at all times [preferably in a locked cabinet].

• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

• Always follow the fabric care instructions supplied by the textile manufacturer.

• Loading door MUST BE CLOSED any time the washer is to fill, tumble or spin. DO NOT bypass the loading door switch by permitting the washer to operate with the loading door open. Do not attempt to open the door until the washer has drained and all moving parts have stopped.

• The lid MUST BE CLOSED any time the washer is to spin. DO NOT bypass the lid release button by permitting the washer to operate with the lid open. Do not attempt to open the lid until the extract compartment has drained and all moving parts have stopped.

• Be aware that hot water is used to flush the supply dispenser, if applicable. Avoid opening the dispenser lid while the machine is running.

• Be aware that hot water is used to flush the supply dispenser. Avoid opening the dispenser lid while the machine is running.

• Do not attach anything to the supply dispenser’s nozzles, if applicable. The air gap must be maintained.

• Do not operate the machine without the water reuse plug or water reuse system in place, if applicable.

• Be sure water connections have a shut-off valve and that fill hose connections are tight. CLOSE the shut-off valves at the end of each wash day.

• Keep washer in good condition. Bumping or dropping the washer can damage safety features. If this occurs, have washer checked by a qualified service person.

• DANGER: Before inspecting or servicing machine, power supply must be turned OFF. The servicer needs to wait for at least 5 minutes after turning the power OFF and needs to check for residual voltage with a voltage meter. The inverter capacitor or EMC filter remains charged with high voltage for some time after powering OFF. This is an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.

• Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry out. ALWAYS disconnect the washer from electrical, power and water supplies before attempting any service.

• Disconnect the power by turning off the circuit breaker or by unplugging the machine. Replace worn power cords.

• Before the washer is removed from service or discarded, remove the door to the washing compartment.

• Before the washer is removed from service or discarded, remove the lid to the washing compartment.

• Failure to install, maintain, and/or operate this washer according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.

NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the washer.

Any problems or conditions not understood should be reported to the dealer, distributor, service agent or the manufacturer.

WARNING

Machine installations must comply with minimum specifications and requirements stated in the applicable Installation Manual, any applicable municipal building codes, water supply requirements, electrical wiring regulations and any other relevant statutory regulations. Due to varied requirements and applicable local codes, this machine must be installed, adjusted, and serviced by qualified maintenance personnel familiar with applicable local codes and the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury, property damage, and/or equipment damage, and will void the warranty.

W820

IMPORTANT: Ensure that the machine is installed on a level floor of sufficient strength. Ensure that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked.

WARNING

Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam must be turned off and the pipe, connections, and components allowed to cool before the pipe can be touched.

SW014

WARNING

Install the machine on a level floor of sufficient strength. Failure to do so may result in conditions which can produce serious injury, death and/or property damage.

W703

DO NOT COPY or TRANSMIT

6 Part No. F8410701ENR13

Safety Decals

Safety decals appear at crucial locations on the machine. Failure to maintain legible safety decals could result in injury to the operator or service technician.

Use manufacturer-authorized spare parts to avoid safety hazards.

Operator Safety

WARNING

NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury.

SW012

The following maintenance checks must be performed daily:

1. Verify that all warning labels are present and legible, replace as necessary.

2. Check door interlock before starting operation of the machine:

a. Attempt to start the machine with the door open. The ma-

chine should not start.

b. Close the door without locking it and start the machine.

The machine should not start.

c. Attempt to open the door while a cycle is in progress. The

door should not open.

If the door lock and interlock are not functioning properly, disconnect power and call a service technician.

3. Do not attempt to operate the machine if any of the following conditions are present:

a. The door does not remain securely locked during the en-

tire cycle. b. Excessively high water level is evident. c. Machine is not connected to a properly grounded circuit.

Safety Information

Do not bypass any safety devices in the machine.

WARNING

Operating the machine with severe out-of-balance loads could result in personal injury and serious equipment damage.

DO NOT COPY or TRANSMIT

W728

7 Part No. F8410701ENR13

Introduction

Model Identification

Information in this manual is applicable to these models:

Introduction

Models

45 Pound [20.4 Kg] UWH045K1L

UWH045K1M UWH045K2L UWH045K2M UWH045T3V

65 Pound [29.5 Kg] UWH065K1L

UWH065K1M UWH065K2L UWH065K2M UWH065T3L UWH065T3M UWH065T4L UWH065T3V

85 Pound [38.6 Kg] UWH085K1M

UWH085K2M UWH085T4V UWH085T3V

105 Pound [47.6 Kg]

130 Pound [59 Kg] UWH130K1M

UWH105K1M UWH105K2M UWH105T3V UWH105T4V

UWH130K2M UWH130T3V UWH130T4V

UWH045T4V UWL045K1L UWL045K1M UWL045K2L UWL045K2M

UWH065T4M UWH065T4V UWL065K1L UWL065K1M UWL065K2L UWL065K2M UWL065T3L UWL065T3M

UWL085K1M UWL085K2M UWL085T4V UWL085T3V

UWL105K1M UWL105K2M UWL105T3V UWL105T4V

UWL130K1M UWL130K2M UWL130T3V UWL130T4V

UWL045T3V UWL045T4V UWN045K1L UWN045K1M UWN045K2L

UWL065T4L UWL065T3V UWL065T4M UWL065T4V UWN065T3L UWN065K1L UWN065K1M UWN065K2L

UWN085K1M UWN085K2M UWN085T3V UWN085T4V

UWN105K1M UWN105K2M UWN105T3V UWN105T4V

UWN130K1M UWN130K2M UWN130T3V UWN130T4V

UWN045K2M UWN045T3V UWN045T4V UWU045K1L UWU045K1M

UWN065K2M UWN065T3M UWN065T3V UWN065T4L UWN065T4M UWN065T4V UWU065K1L UWU065K1M

UWU085K1M UWU085K2M

UWU105K1M UWU105K2M

UWU130K1M UWU130K2M

UWU045K2L UWU045K2M UWU045T3V UWU045T4V

UWU065K2L UWU065K2M UWU065T3L UWU065T3M UWU065T3V UWU065T4L UWU065T4M UWU065T4V

UWU085T3V UWU085T4V

UWU105T3V UWU105T4V

UWU130T3V UWU130T4V

160 Pound [72.6 Kg]

UWH160T3V UWH160T4V

UWL160T3V UWL160T4V

Delivery Inspection

Upon delivery, visually inspect crate, protective cover, and unit for any visible shipping damage. If signs of possible damage are evident, have the carrier note the condition on the shipping papers before the shipping receipt is signed, or advise the carrier of the condition as soon as it is discovered.

Serial Plate Location

The serial plate is located on the valve panel of the machine and, for UniLinc models, is programmed in the control. To access Machine ID through the control:

1. Press and hold

same time.

DO NOT COPY or TRANSMIT

, then , then keypads at the

UWN160T3V UWN160T4V

2. Press the keypad until Diagnostic is highlighted.

3. Press the keypad.

4. Press the

5. Press the keypad.

Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. Refer to Figure 1 .

8 Part No. F8410701ENR13

UWU160T3V UWU160T4V

keypad until machine ID is highlighted.

PHM3254P_SVG

Introduction

Model Example of Serial Plate Location

1. In control (UniLinc Models)

2. On front and back of machine

Figure 1

Manufacturing Date

The manufacturing date for your unit can be found on the serial number. The first two digits indicate the year. The third and fourth digits indicate the month. For example, a unit with serial number 1505000001 was manufactured in May 2015.

Replacement Parts

If literature or replacement parts are required, contact the source from which the machine was purchased or contact Alliance Laundry Systems at +1 (920) 748-3950 for the name and address of the nearest authorized parts distributor.

Customer Service

For technical assistance, contact your local distributor or contact:

Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. www.alliancelaundry.com Phone: +1 (920) 748-3121 Ripon, Wisconsin

DO NOT COPY or TRANSMIT

9 Part No. F8410701ENR13

Specifications and Dimensions

Specifications 45 65 85 105 130 160

Overall Dimensions

Overall width, in. [mm] 34.12 [867] 34.12 [867] 40.12 [1019] 40.12 [1090] 46.12 [1171] 46.12 [1171]

Overall height, in. [mm] 64.43 [1637] 64.43 [1637] 69.08 [1755] 69.08 [1755] 76.05 [1932] 76.05 [1932]

Overall depth, in. [mm] 44.33 [1126] 49.83 [1266] 51.49 [1308] 56.49 [1435] 54.50 [1384] 60.0 [1524]

Weight And Shipping Information

Net weight, lbs. [kg] Through

8/17/14

Starting 8/18/14

Standard shipping weight, lbs. [kg]

Standard shipping volume, ft3 [m3] 75 [2] 75 [2] 107 [3] 107 [3] 139 [4] 139 [4]

Standard shipping dimensions (WxDxH), in. [mm]

Slat crate shipping weight, lbs. [kg]

Slat crate shipping volume, ft3 [m3] 97 [3] 97 [3] 158 [4.5] 158 [4.5] 186 [5.3] 186 [5.3]

Slat crate shipping dimensions (WxDxH), in. [mm]

Through 8/17/14

Starting 8/18/14

Through 8/17/14

Starting 8/18/14

1020 [463] 1060 [481] 1670 [757] 1700 [771] 2040 [925] 2070 [939]

1080 [490] 1100 [499]

1065 [483] 1105 [501] 1720 [780] 1750 [794] 2100 [953] 2130 [966]

1120 [508] 1150 [522]

37.2 x 53.8 x 65 [945 x 1370 x 1650]

1190 [540] 1230 [558] 1870 [848] 1900 [862] 2260 [1025] 2290 [1039]

1250 [567] 1280 [581]

41.7 x 56.8 x

70.8 [1060 x 1440 x 1800]

37.2 x 53.8 x 65 [945 x 1370 x 1650]

41.7 x 56.8 x

70.8 [1060 x 1440 x 1800]

43.2 x 61.8 x

69.4 [1097 x 1570 x 1763]

47.7 x 64.8 x

88.3 [1212 x 1646 x 2243]

43.2 x 61.8 x

69.4 [1097 x 1570 x 1763]

47.7 x 64.8 x

88.3 [1212 x 1646 x 2243]

49.2 x 64.8 x

76.4 [1250 x 1646 x 1941]

53.7 x 67.8 x

88.3 [1364 x 1722 x 1915]

49.2 x 64.8 x

76.4 [1250 x 1646 x 1941]

53.7 x 67.8 x

88.3 [1364 x 1722 x 1915]

Wash Cylinder Information

Cylinder diameter, in. [mm] 31 [787] 31 [787] 36 [914] 36 [914] 42 [1067] 42 [1067]

Cylinder depth, in. [mm] 16.6 [4222] 22.1 [561] 22 [559] 27 [686] 24.5 [622] 30 [762]

Cylinder volume, ft3 [l] 7.3 [185] 9.7 [246] 13 [368] 15.9 [450] 19.6 [555] 24.1 [682]

Perforation size, in. [mm] 0.188 [4.8] 0.188 [4.8] 0.188 [4.8] 0.188 [4.8] 0.188 [4.8] 0.188 [4.8]

Perforation open area, % 21.3 21.3 23 23.4 27.4 27.9

Door Opening Information

Table 1 continues...

DO NOT COPY or TRANSMIT

10 Part No. F8410701ENR13

Specifications and Dimensions

Specifications 45 65 85 105 130 160

Door opening size, in. [mm] 17.8 [452] 17.8 [452] 21.0 [533] 21.0 [533] 24.8 [630] 24.8 [630]

Height of door bottom above floor, in.

28.09 [713] 28.09 [713] 28.09 [713] 28.09 [713] 29.84 [758] 29.84 [758]

[mm]

Drive Train Information

Number of motors in. drive train 1 1 1 1 1 1

Drive motor power, hp [kW] 5.0 [3.7] (V-

speed)

5.0 [3.7] (Vspeed)

7.5 [5.6] 7.5 [5.6] 10 [7.5] 10 [7.5]

Cylinder Speeds / Centrifugal Force Data

1/2 Wash/reverse, rpm [g] 30 [0.4] 30 [0.4] 28 [.4] 28 [.4] 26 [.4] 26 [.4]

Wash/reverse, rpm [g] 42 [.78] 42 [.78] 39 [.78] 39 [.78] 36 [.77] 36 [.77]

Distribution, rpm [g] 75 [2.5] 75 [2.5] 70 [2.5] 70 [2.5] 65 [2.5] 65 [2.5]

Very Low extract, rpm [g] 248 [27] 248 [27] 230 [27] 230 [27] 213 [27] 213 [27]

Low extract, rpm [g] 477 [100] 477 [100] 443 [100] 443 [100] 410 [100] 410 [100]

Medium extract, rpm [g] 674 [200] 674 [200] 626 [200] 626 [200] 579 [200] 579 [200]

High extract (V-speed), rpm [g] 754 [250] 754 [250] 700 [250] 700 [250] 648 [250] 648 [250]

Very High extract (V-speed), rpm [g] 826 [300] 826 [300] 766 [300] 766 [300] 710 [300] 710 [300]

Ultra High extract (V-speed), rpm [g] 954 [400] 954 [400] N/A N/A N/A N/A

Balance Detection

Stability switch installed STD STD STD STD STD STD

Direct Steam Heating (Optional)

Steam inlet connection size, in. [mm] 0.5 [13] 0.5 [13] .5 [13] .5 [13] .75 [19] .75 [19]

Number of steam inlets 1 1 1 1 1 1

Steam required to raise bath temperature, 10°F, lbs. [10°C, kg]

LOW 2.5 [1.1] 3.3 [1.5] 4.6 [2.1] 5.7 [2.6)] 6.7 [3.0] 8.3 [3.8]

MED 2.7 [1.2] 3.7 [1.7] 5.2 [2.4] 6.5 [2.9] 7.8 [3.5] 9.5 [4.3]

HIGH 3.1 [1.4] 4.1 [1.9] 6.1 [2.8] 7.6 [3.4] 9.1 [4.1] 11.1 [5.0]

Average consumption per cycle, BHP [kg] 1.6 [25.4] 2.1 [33.4] 3.1 [49.3] 3.8 [60.4] 4.6 [73.2] 5.8 [92.2]

Electrical Heating (Optional)

Total electrical heating capacity, kW

200V 19.1 19.1 28.6 28.6 N/A N/A

240V 27.4 27.4 41.2 41.2 N/A N/A

380V 17.2 17.2 17.2 17.2 34.4 N/A

415V 20.5 20.5 20.5 20.5 41.0 N/A

480V 27.4 27.4 27.4 27.4 54.8 N/A

Number of electrical heating elements 6/6 6/6 9/6 9/6 12 N/A

Table 1 continues...

DO NOT COPY or TRANSMIT

11 Part No. F8410701ENR13

Specifications and Dimensions

Specifications 45 65 85 105 130 160

Electrical heating element size, kW 4.2 4.2 4.2 4.2 4.2 N/A

Time required to raise bath temperature, min per10°F [5.5°C]

LOW 1.7 2.4 2.2 2.8 1.7 N/A

MED 1.9 2.7 2.5 3.2 2.0 N/A

HIGH 2.1 3.0 3.0 3.7 2.3 N/A

Noise Emission, dB Max Extract 80 80 80 80 80 80

Med Extract 73 73 73 73 73 73

Agitate 61 61 61 61 61 61

Table 1

DO NOT COPY or TRANSMIT

12 Part No. F8410701ENR13

Machine Dimensions

PHM976N_SVG

G H

Specifications and Dimensions

NOTE: UniLinc control model shown.

1. Front View

2. Shell Vent

3. Supply Dispenser

4. Side View

5. Spray Rinse Connection

6. Primary Fill Connections

7. .875 Chem Supply Electrical

8. 1.125 Chem Supply Electrical

9. 1.125 Electrical

10. 1.5000 Electrical

11. Steam Connection

12. Back View

Figure 2

DO NOT COPY or TRANSMIT

13 Part No. F8410701ENR13

Specifications and Dimensions

Machine Dimensions, in. [mm]

45 65 85 105 130 160

A 53.37 [1356] 53.37 [1356] 57.54 [1462] 57.54 [1462] 64.50 [1638] 64.50 [1638]

B 52.99 [1346] 52.99 [1346] 57.92 [1471] 57.92 [1471] 64.88 [1648] 64.88 [1648]

C 49.68 [1262] 49.68 [1262] 54.24 [1378] 54.24 [1378] 61.20 [1554] 61.20 [1554]

D 47.62 [1210] 47.62 [1210] 52.17 [1325] 52.17 [1325] 56.38 [1432] 56.38 [1432]

E 30.48 [774] 30.48 [774] 30.78 [782] 30.78 [782] 29.51 [750] 29.51 [750]

F 14.24 [362] 14.24 [362] 12.28 [312] 12.28 [312] 12.25 [311] 12.25 [311]

G 2.16 [55] 2.16 [55] 2.49 [63] 2.49 [63] 2.90 [74] 2.90 [74]

H 3.58 [91] 3.58 [91] 2.49 [63] 2.49 [63] 2.90 [74] 2.90 [74]

I 7.71 [196] 7.71 [196] 7.71 [196] 7.71 [196] 7.71 [196] 7.71 [196]

J 2.31 [59] 2.31 [59] 2.31 [59] 2.31 [59] 2.31 [59] 2.31 [59]

K 2.83 [72] 2.83 [72] 2.83 [72] 2.83 [72] 2.83 [72] 2.83 [72]

L 4.93 [125] 4.93 [125] 4.93 [125] 4.93 [125] 4.93 [125] 4.93 [125]

M 7.79 [198] 7.79 [198] 8.27 [210] 8.27 [210] 8.27 [210] 8.27 [210]

N 10.41 [264] 10.41 [264] 11.37 [289] 11.37 [289] 11.37 [289] 11.37 [289]

O 14.64 [372] 14.64 [372] 23.05 [585] 23.05 [585] 26.05 [662] 26.05 [662]

P 16.12 [409] 16.12 [409] 23.05 [585] 23.05 [585] 26.05 [662] 26.05 [662]

Q 21.93 [557] 21.93 [557] 27.93 [709] 27.93 [709] 33.93 [862] 33.93 [862]

R 28.81 [732] 28.81 [732] 34.81 [884] 34.81 [884] 40.81 [1037] 40.81 [1037]

S 55.43 [1408] 55.43 [1408] 59.98 [1523] 59.98 [1523] 66.94 [1700] 66.94 [1700]

T 55.84 [1418] 55.84 [1418] 57.42 [1458] 57.42 [1458] 64.38 [1635] 64.38 [1635]

U 1.01 [26] 1.01 [26] 0.88 [22] 0.88 [22] 1.11 [28] 1.11 [28]

V 2.49 [63] 2.49 [63] 1.88 [48] 1.88 [48] 2.16 [55] 2.16 [55]

W 34.24 [870] 34.24 [870] 42.24 [1073] 42.24 [1073] 44.74 [1136] 44.74 [1136]

X 35.63 [905] 41.13 [1045] 48.50 [1232] 48.50 [1232] 51.50 [1308] 51.50 [1308]

Y 44.33 [1126] 49.83 [1266] 51.49 [1308] 56.49 [1435] 54.50 [1384] 60.0 [1524]

Z 64.43 [1637] 64.43 [1637] 69.08 [1755] 69.08 [1755] 76.05 [1932] 76.05 [1932]

AA 33.69 [856] 33.69 [856] 39.45 [1002] 39.45 [1002] 45.68 [1160] 45.68 [1160]

BB 33.69 [856] 33.69 [856] 39.29 [998] 39.29 [998] 42.94 [1091] 42.94 [1091]

CC 28.78 [731] 28.78 [731] 28.78 [731] 28.78 [731] 30.54 [776] 30.54 [776]

DD 28.09 [713] 28.09 [713] 28.09 [713] 28.09 [713] 29.84 [758] 29.84 [758]

EE 20.88 [530] 20.88 [530] 22.62 [575] 22.62 [575] 28.62 [727] 28.62 [727]

Table 2 continues...

DO NOT COPY or TRANSMIT

14 Part No. F8410701ENR13

Specifications and Dimensions

Machine Dimensions, in. [mm]

45 65 85 105 130 160

FF 30.77 [782] 30.77 [782] 36.77 [934] 36.77 [934] 42.77 [1086] 42.77 [1086]

GG 34.12 [867] 34.12 [867] 40.12 [1019] 40.12 [1019] 46.12 [1171] 46.12 [1171]

HH 3.50 [89] 3.50 [89] 3.50 [89] 3.50 [89] 3.50 [89] 3.50 [89]

II 60.94 [1548] 60.94 [1548] 63.88 [1623] 63.88 [1623] 68.90 [1750] 68.90 [1750]

JJ 64.63 [1642] 64.63 [1642] 67.59 [1717] 67.59 [1717] 72.61 [1844] 72.61 [1844]

KK 24.64 [626] 24.64 [626] 28.22 [717] 28.22 [717] 31.65 [804] 31.65 [804]

Table 2

DO NOT COPY or TRANSMIT

15 Part No. F8410701ENR13

PHM960N_SVG

BA AB

Specifications and Dimensions

Mounting Bolt Hole Locations - 45 and

65 Pound Models

45 and 65 Pound [20.4 and 29.5 Kg] Models (refer to Table 3 )

NOTE: For single machine installations or two machines installed back to back, use the outside bolt holes marked “A”. For multiple machines installed side by side with minimum clearance, use the inside bolt holes marked “B”.

1. Front of Mounting Bolt Template (45)

2. Front of Mounting Bolt Template (65)

DO NOT COPY or TRANSMIT

Figure 3

16 Part No. F8410701ENR13

Machine Capacity Dimensions, in. [mm] - 45 and 65 Pound [20.4 and 29.5 Kg] Models

45 65

A 34.12 [867] 34.12 [867]

B 32.24 [819] 32.24 [819]

C 25.48 [647] 25.48 [647]

D .94 [24] .94 [24]

E 4.32 [110] 4.32 [110]

F .94 [24] .94 [24]

G 1.96 [50] 1.96 [50]

H 3 [76] 3 [76]

I 16 [406] 16 [406]

J 26 [660] 26 [660]

K 33.67 [855] Not Applicable

Specifications and Dimensions

L Not Applicable 42.17 [1071]

M Outside 35.99 [914] 35.99 [914]

N 41.41 [1051] 41.41 [1051]

O Inside 30.08 [764] 30.08 [764]

P 36.4 [924] 36.4 [924]

Table 3

DO NOT COPY or TRANSMIT

17 Part No. F8410701ENR13

PHM957N_SVG

Specifications and Dimensions

Mounting Bolt Hole Locations - 85 and

105 Pound Models

85 and 105 Pound [38.6 and 47.6 Kg] Models (refer to Table 4 )

1. Front of Mounting Bolt Template (85)

2. Front of Mounting Bolt Template (105)

Figure 4

DO NOT COPY or TRANSMIT

18 Part No. F8410701ENR13

Machine Capacity Dimensions, in. [mm] - 85 and 105 Pound [38.6 and 47.6 Kg] Models

85 105

A 40.12 [1019] 40.12 [1019]

B 38.24 [971] 38.24 [971]

C 28.24 [717] 28.24 [717]

D 5.94 [151] 5.94 [151]

E 5.89 [149] 5.89 [149]

F .94 [24] .94 [24]

G 2.20 [56] 2.20 [56]

H 3.08 [78] 3.08 [78]

I 18 [457] 18 [457]

J 33.50 [851] 33.50 [851]

K 44.38 [1127] Not Applicable

Specifications and Dimensions

L Not Applicable 49.38 [1254]

M Outside 42.27 [1074] 42.27 [1074]

N 50.84 [1291] 50.84 [1291]

O Inside 33.49 [851] 33.49 [851]

P 43.82 [1113] 43.82 [1113]

Table 4

DO NOT COPY or TRANSMIT

19 Part No. F8410701ENR13

PHM958N

Specifications and Dimensions

Mounting Bolt Hole Locations - 130 and

160 Pound Models

130 and 160 Pound [59 and 72.6 Kg] Models (refer to Table 5 )

1. Front of Mounting Bolt Template (130)

2. Front of Mounting Bolt Template (160)

Figure 5

Machine Capacity Dimensions, in. [mm] - 130 and 160 Pound [59 and 72.6 Kg] Models

130 160

A 46.12 [1171] 46.12 [1171]

B 44.24 [1124] 44.24 [1124]

C 34.24 [870] 34.24 [870]

Table 5 continues...

DO NOT COPY or TRANSMIT

20 Part No. F8410701ENR13

Machine Capacity Dimensions, in. [mm] - 130 and 160 Pound [59 and 72.6 Kg] Models

130 160

D 5.94 [151] 5.94 [151]

E 5.89 [150] 5.89 [150]

F .94 [24] .94 [24]

G 2.20 [56] 2.20 [56]

H 3.31 [84] 3.31 [84]

I 18 [457] 18 [457]

J 33.50 [851] 33.50 [851]

K 47.11 [1197] Not Applicable

L Not Applicable 52.61 [1336]

M Outside 47.76 [1213] 47.76 [1213]

N 55.49 [1409] 55.49 [1409]

Specifications and Dimensions

O Inside 43.17 [1097] 43.17 [1097]

P 47.90 [1217] 47.90 [1217]

Table 5

DO NOT COPY or TRANSMIT

21 Part No. F8410701ENR13

PHM819N_SVG

Specifications and Dimensions

Floor Layout

Dimensional Clearances - Side by Side Mount (refer to Table 6 )

1. Wall

2. Rear of Base

3. Machine 1

4. Machine 2

5. Front of Base

Figure 6

Dimensional Clearances, in. [mm] - Side by Side Mount

Description 45-160

A Distance to wall (minimum) 20 [508]

B Adjacent unit spacing (minimum) Standard 18 [457]

Narrow* 12 [305]

Ultra-narrow* 6 [153]

* Requires additional concrete depth and rebar. Refer to Machine Installation.

Table 6

DO NOT COPY or TRANSMIT

22 Part No. F8410701ENR13

Dimensional Clearances - Back to Back Mount (refer to Table 7 )

PHM810N_SVG

Specifications and Dimensions

1. Front of Base

2. Machine 2

3. Rear of Base

4. Machine 1

5. Edge of Concrete Pad or Wall

Figure 7

DO NOT COPY or TRANSMIT

23 Part No. F8410701ENR13

Specifications and Dimensions

Dimensional Clearances, in. [mm] - Back to Back Mount

Description 45-105 130-160

A Distance to back edge of machine 2 (minimum) 20 [508] 20 [508]

B Adjacent wall spacing

(minimum)

Standard 12 [305] 16 [407]

Narrow* 9 [226] 9 [226]

Ultra-narrow* 6 [153] 6 [153]

* Requires additional concrete depth and rebar. Refer to Machine Installation.

Table 7

DO NOT COPY or TRANSMIT

24 Part No. F8410701ENR13

+ 56 hidden pages

Unimac UWN160T4V Owner’s Manual

Table of Contents

Safety Information

Explanation of Safety Messages

Important Safety Instructions

Safety Decals

Operator Safety

Introduction

Model Identification

Delivery Inspection

Serial Plate Location

Manufacturing Date

Replacement Parts

Customer Service

Specifications and Dimensions

Specifications and Dimensions

Machine Dimensions

Floor Layout