Ubiquiti UVC-G3-5, UVC-G3 Quick Installation Guide
1080p Indoor/Outdoor
IP Camera with Infrared
Model: UVC-G3
Introduction
Thank you for purchasing the Ubiquiti Networks® UniFi® Video
Camera G3. This Quick Start Guide is designed to guide you
through installation and also includes warranty terms.
Package Contents
UVC-G3
Cable Gland
Pole Mount
* Only the single-pack of the UVC-G3 includes a PoE adapter and a
power cord.
Bracket
PoE Adapter (24V, 0.5A)
with Mounting Bracket*
Screw Anchors
(Qty. 2, 8 x 40 mm)
Machine Screws
(Qty. 2, M4x10)
Power Cord*
Self-Tapping Screws
(Qty. 2, M4 x 30)
1080p FHD Indoor/Outdoor
Surveillance Camera with
Built-In Infrared
Model: UVC-G3
Quick Start
Guide
Installation Requirements
• Shielded Category 5 (or above) cabling should be used for
all wired Ethernet connections and should be grounded
through the AC ground of the PoE.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial-grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). Shielded Ethernet
cable and earth grounding must be used for outdoor installations as conditions of product
warranty. TOUGHCable™ is designed for outdoor installations. It is the customer’s responsibility
to follow local country regulations.
www.ubnt.com/toughcable
Hardware Overview
IR LED
Camera Lens
Ethernet
RESET
M/N: UVC-G3
Camera Lock
Ethernet Connects to the Ubiquiti PoE adapter or UniFi
Switch for 24V passive PoE power and data.
Reset To reset to factory defaults, press and hold the Reset
button for more than 10 seconds while the camera is already
poweredon.
24V 0.5A PoE
Reset
Tilt/Mount Lock
Adjustable Base
Cable Gland
Mounting Base
Hardware Installation
The UniFi Video Camera G3 can be mounted on a wall, ceiling,
or pole. Follow the appropriate steps for your installation:
Wall/Ceiling Mount
1. Remove the Mounting Base from the camera by turning the
Tilt/Mount Lock counterclockwise.
2. Mark the mounting holes on the wall or ceiling.
Cable
Slot
Note: If you are running the cable along the wall or
ceiling, ensure that you position the Cable Slot towards
the direction you want the cabling to run.
3. Use a 7 mm drill bit to drill the mounting holes in the wall
or ceiling.
Note: If
you are running the Ethernet cable through
the wall, cut a hole centered between the mounting
holes that is large enough to feed the cable through.
4. Insert a Screw Anchor into each mounting hole.
5. If you are feeding the Ethernet cable through the wall or
ceiling, do so now and feed it through the Mounting Base.
If not, feed the Ethernet cable through the Mounting Base
and place the cable in the Cable Slot.
6. Fasten the Mounting Base to the wall or ceiling using two
Self-Tapping Screws.
7. Remove the camera from the Adjustable Base by turning
the Camera Lock counterclockwise.
8. Feed the Ethernet cable through the Cable Gland and
M/N: UVC-G3 24V 0.5A PoE
RESET
Adjustable Base. Then connect the cable to the Ethernet Port
on the camera.
9. Connect the camera back to the Adjustable Base by turning
the Camera Lock clockwise.
10. Set the pan angle of the Adjustable Base while connecting
it to the Mounting Base. Then lock the camera to the
Mounting Base by turning the Tilt/Mount Lock clockwise.
Pole Mount
To mount the UVC-G3 on a pole, a metal strap or hose clamp is
required (not included).
1. Feed the metal strap through the slots on the Pole Mount
Bracket.
Loading...