Ubiquiti ES-16XP User Manual

Rack-Mount
Power over Ethernet
Managed Switches

Model: ES-16XP

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgeSwitch®
16XP. This Quick Start Guide is designed to guide you through
installation and includes warranty terms.

Package Contents

EdgeSwitch 16XP

Flathead Screws

(Qty. 2)

Phillips Screws

(Qty. 4)

Cage Nuts

(Qty. 4)

Rack-Mount
Power over Ethernet
Managed Switches

Model: ES-16XP

Power Cords (Qty. 2) Quick Start Guide

TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). Shielded Ethernet
cable and earth grounding must be used for outdoor installations as conditions of product
warranty. TOUGHCable™ is designed for outdoor installations. It is the professional installer’s
responsibility to follow local country regulations, including operation within legal frequency
channels, output power, and Dynamic Frequency Selection (DFS) requirements.

Hardware Overview

A and B designate the two 8-Port EdgeSwitch devices housed
in the rack. This may be useful for the Location setting on the
Device tab in the Configuration Interface.

Front Panel Ports

Management Ports 1-8

Management Ports 1-8

ResetUSB

ResetUSB

EdgeSwitch A EdgeSwitch B

Interface Description

Management

Ports 1-8 10/100/1000 Mbps ports for switching and

10/100 Mbps port used to access the
EdgeSwitch Configuration Interface.

PoE (also available for management by
default).

USB Reserved for future use.

Reset

To reset to factory defaults, press and hold
the Reset button for more than 10 seconds
while the unit is already powered on.

Back Panel

Ventilation HolesVentilation Holes

Power Power

Note: There are additional ventilation holes on the top

and sides of the EdgeSwitch.

Front Panel LEDs

Power/Link

LED State Status

Off No Power/No Link

Power/
Link

MGMT

Ports 1-8

Amber

Off No Power over Ethernet

PoE

Green 24V Power over Ethernet
Amber 48V Power over Ethernet
Off No link
Amber Link established at 10/100 Mbps

Speed/

Amber

Link/

Flashing

Act

Green Link established at 1000 Mbps
Green

Flashing

Speed/Link/Act

PoE

After bootup, the LED indicates
power. After an initial link is
established, the LED indicates a
10/100 Mbps connection. If the link
terminates, the LED turns off until
a link is re-established. If the unit
reboots, the LED will again indicate
power until a link is established.

Link activity at 10/100 Mbps

Link activity at 1000 Mbps

Installation Requirements

• Phillips and flathead screwdrivers

• Standard-sized, 19" wide rack with an available 1U space

• For indoor applications, use Category 5 (or above) UTP
cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)
cabling should be used for all wired Ethernet connections
and should be grounded through the AC ground of the

powersupply.

We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial-grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit www.ubnt.com/toughcable

IMPORTANT: Although the cabling can be located

outdoors, the EdgeSwitch itself should be housed
inside a protective enclosure.

WARNING: To reduce the risk of fire or electric shock,

do not expose this EdgeSwitch to rain or moisture.

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF
CLEARANCE NEXT TO THE VENTILATION HOLES FOR
ADEQUATE AIRFLOW.

Hardware Installation

1. Remove the faceplate from the EdgeSwitch by lifting up

the bottom portion of the faceplate.

2. Connect the Power Cord to the Power port of each

EdgeSwitch.